MULTI-SCALE COHERENT STRUCTURES IN TURBULENT BOUNDARY LAYER DETECTED BY LOCALLY AVERAGED VELOCITY STRUCTURE FUNCTIONS

The time sequence of longitudinal velocity component at different vertical locations in turbulent boundary layer was finely measured in a wind tunnel. The concept of coarse_grained velocity structure functions, which describes the relative motions of straining and compressing for multi_scale eddy structures in turbulent flows, was put forward based on the theory of locally multi_scale average. Based on the consistency between coarse_grained velocity structure function and Harr wavelet transformation,detecting method was presented, by which the coherent structures and their intermittency was identified by multi_scale flatness factor calculated by locally average structure function. Phase_averaged evolution course for multi_scale coherent eddy structures in wall turbulence were extracted by this conditional sampling to educe scheme. The dynamics course of multi_scale coherent eddy structures and their effects on statistics of turbulent flows were studied.

Experimental investigation of closed-loop active control to modulate coherent structures by mu-level method

The experimental research on zero-net-mass-flux jet closed-loop active control was conducted in the wind tunnel.The mu-level method successfully detected burst events of the coherent structures. The streamwise velocity signals in the turbulent boundary layer were measured by HWA. The drag reduction rate of 16.7% is obtained comparable to that of the open-loop control and saves 75% of the input energy at the asynchronous 100 V/160 Hz control case, which reflects the advantages of the closed-loop control. The experimental findings indicate that the intensity increases in the near-wall region.The perturbation of the PZT vibrators on the skewness factor is concentrated in the region y+< 60. The generation of highspeed fluids is depressed and the downward effect of high-speed fluids weakens. The alteration of energy distribution and the discernible impact of modulation between structures of varying scales are observed. The correlation coefficient exhibits a strong positive correlation, which indicates that the large-scale structures produce modulation effect on small-scale ones.The occurrence of burst events is effectively suppressed. The disturbance has the characteristics of stable periodicity,positive and negative symmetry, low intermittency, and high pulsation strength. The conditional phase waveform shows that the fluctuation amplitude increases, indicating amplitude modulation effects on coherent structures.

Multi-Scale Design and Optimization of Composite Material Structure for Heavy-Duty Truck Protection Device

In this paper,to present a lightweight-developed front underrun protection device(FUPD)for heavy-duty trucks,plain weave carbon fiber reinforced plastic(CFRP)is used instead of the original high-strength steel.First,the mechanical and structural properties of plain carbon fiber composite anti-collision beams are comparatively analyzed from a multi-scale perspective.For studying the design capability of carbon fiber composite materials,we investigate the effects of TC-33 carbon fiber diameter(D),fiber yarn width(W)and height(H),and fiber yarn density(N)on the front underrun protective beam of carbon fiber compositematerials.Based on the investigation,a material-structure matching strategy suitable for the front underrun protective beam of heavy-duty trucks is proposed.Next,the composite material structure is optimized by applying size optimization and stack sequence optimization methods to obtain the higher performance carbon fiber composite front underrun protection beam of commercial vehicles.The results show that the fiber yarn height(H)has the greatest influence on the protective beam,and theH1matching scheme for the front underrun protective beamwith a carbon fiber composite structure exhibits superior performance.The proposed method achieves a weight reduction of 55.21% while still meeting regulatory requirements,which demonstrates its remarkable weight reduction effect.

Complex-amplitude Fourier single-pixel imaging via coherent structured illumination

We propose a method of complex-amplitude Fourier single-pixel imaging(CFSI)with coherent structured illumination to acquire both the amplitude and phase of an object.In the proposed method,an object is illustrated by a series of coherent structured light fields,which are generated by a phase-only spatial light modulator,the complex Fourier spectrum of the object can be acquired sequentially by a single-pixel photodetector.Then the desired complex-amplitude image can be retrieved directly by applying an inverse Fourier transform.We experimentally implemented this CFSI with several different types of objects.The experimental results show that the proposed method provides a promising complex-amplitude imaging approach with high quality and a stable configuration.Thus,it might find broad applications in optical metrology and biomedical science.

Combined Insights from Leachate Structure and Microstructure Characteristics for Eating Quality of Convenience Rice Processed by Super-Heated and Pressurized Steam Technologies

Convenience rice has become widely popular due to its easy availability for cooking. This study investigated the starch structure and composition of leachate and the microstructure of reheated convenience rice using novel processing technologies: super-heated steaming(SHS), auto-electric cooking(AEC), and pressurized-steam cooking(PSC). Additionally, the effect of two different target water contents(58% and 63%) was also evaluated. The PSC_63% sample had the highest total solids and amylopectin amount in the leachate. The amylopectin amount in the leachate differed significantly based on the targeted water content. Morphological characterization revealed that the swelling of starch and the coated layer on the surface of rice grains were most pronounced in the PSC_63% sample due to the pressure processing. The textural hardness of the AEC_58% sample was much higher than that of the other samples. The PSC_63% sample had the highest textural adhesiveness value, which can be attributed to the highest amylopectin amount in the leachate. Sensory characterization showed that the PSC_63% sample had the highest glossiness, whiteness, moistness, and overall acceptability. The principal component analysis score plots presented substantial differences in the leachate and textural and sensory characteristics of reheated convenience rice among the different processing technologies.

Improved multi-scale inverse bottleneck residual network based on triplet parallel attention for apple leaf disease identification

Accurate diagnosis of apple leaf diseases is crucial for improving the quality of apple production and promoting the development of the apple industry. However, apple leaf diseases do not differ significantly from image texture and structural information. The difficulties in disease feature extraction in complex backgrounds slow the related research progress. To address the problems, this paper proposes an improved multi-scale inverse bottleneck residual network model based on a triplet parallel attention mechanism, which is built upon ResNet-50, while improving and combining the inception module and ResNext inverse bottleneck blocks, to recognize seven types of apple leaf(including six diseases of alternaria leaf spot, brown spot, grey spot, mosaic, rust, scab, and one healthy). First, the 3×3 convolutions in some of the residual modules are replaced by multi-scale residual convolutions, the convolution kernels of different sizes contained in each branch of the multi-scale convolution are applied to extract feature maps of different sizes, and the outputs of these branches are multi-scale fused by summing to enrich the output features of the images. Second, the global layer-wise dynamic coordinated inverse bottleneck structure is used to reduce the network feature loss. The inverse bottleneck structure makes the image information less lossy when transforming from different dimensional feature spaces. The fusion of multi-scale and layer-wise dynamic coordinated inverse bottlenecks makes the model effectively balances computational efficiency and feature representation capability, and more robust with a combination of horizontal and vertical features in the fine identification of apple leaf diseases. Finally, after each improved module, a triplet parallel attention module is integrated with cross-dimensional interactions among channels through rotations and residual transformations, which improves the parallel search efficiency of important features and the recognition rate of the network with relatively small computational costs while the dimensional dependencies are improved. To verify the validity of the model in this paper, we uniformly enhance apple leaf disease images screened from the public data sets of Plant Village, Baidu Flying Paddle, and the Internet. The final processed image count is 14,000. The ablation study, pre-processing comparison, and method comparison are conducted on the processed datasets. The experimental results demonstrate that the proposed method reaches 98.73% accuracy on the adopted datasets, which is 1.82% higher than the classical ResNet-50 model, and 0.29% better than the apple leaf disease datasets before preprocessing. It also achieves competitive results in apple leaf disease identification compared to some state-ofthe-art methods.

Clinical characteristics of peripapillary hyperreflective ovoid mass-like structures in myopic children

AIM:To describe the characteristics of peripapillary hyperreflective ovoid mass-like structure(PHOMS)in myopic children and to investigate factors associated with PHOMS.METHODS:This retrospective observational study included 101 eyes of 101 children(age≤17y)with myopia.All included patients underwent comprehensive clinical examination.Optic nerve canal parameters,including disc diameter,optic nerve head(ONH)tilt angle,and border tissue angle were measured using serial enhanced-depth imaging spectral-domain optical coherence tomography(EDI-OCT).Based on the optic disc drusen consortium’s definition of PHOMS,eyes were classified as PHOMS group and non-PHOMS group.PHOMS was categorized according to height.RESULTS:Sixty-seven(66.3%)eyes were found with PHOMS.Small PHOMS could only be detected by optical coherence tomography(OCT).Medium PHOMS could be seen with blurred optic disc borders corresponding to OCT.The most frequent location of PHOMS was at the nasosuperior(91%,61 of 67 eyes)to ONH disc.The axial length and spherical equivalent were more myopic in the PHOMS group than in the non-PHOMS group(both P<0.001).ONH tilt angle was also significantly greater in PHOMS group than in non-PHOMS group[8.90(7.16-10.54)vs 3.93(3.09-5.25),P<0.001].Border tissue angle was significantly smaller in PHOMS group than in non-PHOMS group[29.70(20.90-43.81)vs 45.62(35.18-60.45),P<0.001].In the multivariable analysis,spherical equivalent(OR=3.246,95%CI=1.209-8.718,P=0.019)and ONH tilt angle(OR=3.275,95%CI=1.422-7.542,P=0.005)were significantly correlated with PHOMS.There was no disc diameter associated with PHOMS.In the linear regression analysis,border tissue angle was negatively associated with PHOMS height(β=-2.227,P<0.001).CONCLUSION:PHOMS is associated with optic disc tilt and optic disc nasal shift in myopia.Disc diameter is not a risk factor for PHOMS.The changes in ONH caused by axial elongation facilitated an understanding of the mechanism of PHOMS.

Tomographic PIV investigation of coherent structures in a turbulent boundary layer flow

Tomographic particle image velocimetry was used to quantitatively visualize the three-dimensional co- herent structures in the logarithmic region of the turbulent boundary layer in a water tunnel. The Reynolds number based on momentum thickness is Reo = 2 460. The in- stantaneous velocity fields give evidence of hairpin vortices aligned in the streamwise direction forming very long zones of low speed fluid, which is flanked on either side by high- speed ones. Statistical support for the existence of hairpins is given by conditional averaged eddy within an increasing spanwise width as the distance from the wall increases, and the main vortex characteristic in different wall-normal re- gions can be reflected by comparing the proportion of ejec- tion and its contribution to Reynolds stress with that of sweep event. The pre-multiplied power spectra and two-point cor- relations indicate the presence of large-scale motions in the boundary layer, which are consistent with what have been termed very large scale motions （VLSMs）. The three dimen-sional spatial correlations of three components of veloc- ity further indicate that the elongated low-speed and high- speed regions will be accompanied by a counter-rotating roll modes, as the statistical imprint of hairpin packet structures, all of which together make up the characteristic of coherent structures in the logarithmic region of the turbulent boundary layer （TBL）.

Gustiness and Coherent Structure of Strong Winds and Their Role in Dust Emission and Entrainment

After the passage of a cold front, spring in northern China, the outbreak of strong wind is often accompanied by dust emissions. Through analyses of data in the atmospheric boundary layer during a typical case, it is revealed there are rather regular gust wave packets superimposed on the basic strong wind flow. The gust-wind wave packets have a period equal to around 3 6 rains and possess coherent structure. As the vertical transport of momentum is decomposed into separate parts by （a） basic flow, （b） gust-wind, and （c） turbulence, they are all in a downwards direction at the lower levels of the atmospheric boundary layer during strong wind periods. However, （a） is the largest, while （b） and （c） are comparable. All these are very different from the case of normal weather. Besides, the friction velocity at the ground surface is also much larger than that of normal weather and should be corrected by taking the contributions of the basic flow and gust-wind into account.The strong basic flow with descending motion is very favorable for soil erosion and sand/dust emissions, but suppresses the entrainment of dust particles by keeping them within the bottom levels of the atmospheric boundary layer. Owing to the coherent structure of gust-wind, dust particles can effectively overcome the systematic descending air motion and penetrate into the middle and upper levels of the atmospheric boundary layer, and then propagate further and diffuse into the troposphere where ascending air motion prevails.

THE EFFECT OF COMPLIANT COATINGS ON COHERENT STRUCTURE IN TURBULENT BOUNDARY LAYERS

The velocity profile,turbulence intensity profile,streaky structure and bursting frequency in turbulent boundary layers over a flat plate with compliant coatings were investigated by Laser Doppler Anemometry and condi- tional sampling techniques.This experiment led to the conclusions that in boundary layer flows on a compliant wall,as compared with that on a rigid wall,the log law region was extended further away from the wall,and that the maximum value of each turbulence intensity profile in the near wall region was reduced and the bursting frequency obviously decreased with the compliant coatings.One point worthy of notice was that the above results were very much like those of polymer drag reduction experiments.

Coherent structures and wavepackets in subsonic transitional turbulent jets

A large eddy simulation (LES) is performed for two subsonic jets with a Reynolds number of , which have different core temperatures, i.e., the cold and hot jet. The far-field overall sound pressure levels (OASPL) and noise spectra are well validated against previous experimental results. It is found that the OASPL is raised by heating at shallow angles. The most energetic coherent structures are extracted with specified frequencies using the filter based on the frequency domain variant of the snapshot method of proper orthogonal decomposition (POD). The modes have high coherence of near-field pressure for both jets, while the coherence of modes is enhanced greatly by heating. Based on the coherent structures, spatial wavepackets are educed and the characteristics of growth, saturation and decay are analyzed and compared between the two jets in detail. The results show that heating would enhance the linear growth rate for high frequency components, and nonlinear growth rates for low frequency components in general, which are responsible for higher OASPL in the hot jet. The far-field sound generated by wavepackets is computed using the Kirchhoff extrapolation, which matches well with that of LES at shallow angles. This indicates that the wavepackets associated with coherent structures are dominant sound sources in forced transitional turbulent jets. Additionally, the present POD method is proven to be a robust tool to extract the salient features of the wavepackets in turbulent flows.

A KIND OF FAST CHANGING COHERENT STRUCTURE IN A TURBULENT BOUNDARY LAYER

Coherent structures of a turbulent boundary layer were investigated by hydrogen bubble method. A kind of fast changing structure was observed. That is a spot in which all the hydrogen bubbles vanish much faster than in other regions. This investigation verified that dark-spot is formed by a strong sweep from outer layer. Inside a dark-spot the local instantaneous flow speed might be four times of its neighboring high-speed streaks. Comparing with the low/high speed streaks, both dark-spot and the vortical structures around it are changing very fast. Around dark-spot intensive shear layers are formed and indications of the generation of small-scale structures could be observed.

WAVELET ANALYSIS OF COHERENT STRUCTURES IN A THREE-DIMENSIONAL MIXING LAYER

Wavelet analysis is applied to the results obtained by the direct numerical simulation of a three-dimensional (3D) mixing layer in order to investigate coherent structures in dimension of scale. First, 3D orthonormal wavelet bases are constructed, and the corresponding decomposition algorithm is developed. Then the Navier-Stokes equations are transformed into the wavelet space and the architecture for multi-scale analysis is established. From this architecture, the coarse field images in different scales are obtained and some local statistical quantities are calculated. The results show that, with the development of a mixing layer, the energy spectrum densities for different wavenumbers increase and the energy is transferred from the average flow to vortex structures in different scales. Due to the non-linear interactions between different scales, cascade processes of energy are very complex. Because vortices always roll and pair at special areas, for a definite scale, the energy is obtained from other scales at some areas while it is transferred to other scales at other areas. In addition, energy dissipation and transfer always occur where an intense interaction between vortices exists.

AN EXPERIMENTAL STUDY ON TURBULENT COHERENT STRUCTURES NEAR A SHEARED AIR-WATER INTERFACE

The turbulence structures near a sheared air-water interface were experimentally investigated with the hydrogen bubble visualization technique. Surface shear was imposed by an airflow over the water flow which was kept free from surface waves. Results show that the wind shear has the main influence on coherent structures under air-water interfaces. Low- and high- speed streaks form in the region close to the interface as a result of the imposed shear stress. When a certain airflow velocity is reached, “turbulent spots” appear randomly at low-speed streaks with some characteristics of hairpin vortices. At even higher shear rates, the flow near the interface is dominated primarily by intermittent bursting events. The coherent structures observed near sheared air-water interfaces show qualitative similarities with those occurring in near-wall turbulence. However, a few distinctive phenomena were also observed, including the fluctuating thickness of the instantaneous boundary layer and vertical vortices in bursting processes, which appear to be associated with the characteristics of air-water interfaces.

Two-point statistics of coherent structures in turbulent flow over riblet-mounted surfaces

Direct numerical simulations (DNS) of turbulent flow over a drag-reducing and a drag-increasing riblet configuration are performed. Three-dimensional two-point statistics are presented for the first time to quantify the interaction of the riblet surfaces with the coherent, energy-bearing eddy structures in the near-wall region. Results provide statistical evidence that the averaged organization of the streamwise vortices in the drag-reducing case is lifted above the riblet tip, while in the drag-increasing case the streamwise vortices are embedded further into the riblet cove. In the spanwise direction, the cores of the streamwise vortices over the riblet surfaces are shown to be closer to each other than those for flow over the smooth wall, and wider riblet spacing leads to more reduction on their spanwise distances. In the cases with riblets the streamwise vortices have longer streamwise lengths, but their inclination angles do not change much.

A MECHANISM FOR EXCITATION OF COHERENT STRUCTURES IN WALL REGION OF A TURBULENT BOUNDARY LAYER

The problem of how the coherent structures in the wall region of a turbulent boundary layer could be excited by the disturbances from the outer region was investigated by using direct numerical simulation (DNS) method. The results show that velocity disturbances at the upper boundary of the wall region could excite coherent structures in the wall region, thus offering a more comprehensive model for individual coherent structures.

Exotic Localized Coherent Structures of New (2+1)-Dimensional Soliton Equation

The variable separation approach is used to obtain localized coherent structures of the new (2+1)-dimensional nonlinear partialdifferential equation. Applying the Backlund transformation and introducing the arbitraryfunctions of the seed solutions, the abundance of the localized structures of this model are derived. Some special types ofsolutions solitoff, dromions, dromion lattice, breathers and instantons are discussed by selecting the arbitrary functionsappropriately. The breathers may breath in their amplititudes, shapes, distances among the peaks and even the numberof the peaks.

The spatial-temporal evolution of coherent structures in log law region of turbulent boundary layer

The spatial-temporal evolution of coherent structures （CS） is significant for turbulence control and drag re- duction. Among the CS, low and high speed streak structures show typical burst phenomena. The analysis was based on a time series of three-dimensional and three-component （3D-3C） velocity fields of the flat plate turbulent boundary layer （TBL） measured by a Tomographic and Time-resolved PIV （Tomo TRPIV） system. Using multi-resolution wavelet transform and conditional sampling method, we extracted the intrinsic topologies and found that the streak structures appear in bar-like patterns. Furthermore, we seized locations and velocity information of transient CS, and then calculated the propagation velocity of CS based on spatial-temporal cross-correlation scanning. This laid a foundation for further studies on relevant dynamics properties.

AN EXPERIMENTAL STUDY OF THE LARGE SCALE COHERENT STRUCTURES IN A FORCED FREE SHEAR LAYER

The dynamic characteristics of the large scale coherent structures in a forced free shear layer are experi- mentally studied by means of flow visualization. The quantitative measurements are acquired by the use of a LDV. It is shown that the development of the coherent structures can be greatly influenced by upstream artificial perturbations and as a result the mixing in the layer can be controlled. Like vortex merging, vortex splitting is also a common evolu- tion pattern in the development of the coherent structures.

Tomographic PIV investigation on coherent vortex structures over shark-skin-inspired drag-reducing riblets

Nature has shown us that the microstructure of the skin of fast-swimming sharks in the ocean can reduce the skin friction drag due to the well-known shark-skin effect.In the present study,the effect of shark-skin-inspired riblets on coherent vortex structures in a turbulent boundary layer（TBL） is investigated.This is done by means of tomographic particle image velocimetry（TPIV） measurements in channel fl ws over an acrylic plate of drag-reducing riblets at a friction Reynolds number of 190.The turbulent fl ws over drag-reducing riblets are verifie by a planar time-resolved particle image velocimetry（TRPIV） system initially,and then the TPIV measurements are performed.Two-dimensional（2D） experimental results with a dragreduction rate of around 4.81% are clearly visible over triangle riblets with a peak-to-peak spacing s＋of 14,indicating from the drag-reducing performance that the buffer layer within the TBL has thickened;the logarithmic law region has shifted upward and the Reynolds shear stress decreased.A comparison of the spatial topological distributions of the spanwise vorticity of coherent vortex structures extracted at different wall-normal heights through the improved quadrant splitting method shows that riblets weaken the amplitudesof the spanwise vorticity when ejection（Q2） and sweep（Q4） events occur at the near wall,having the greatest effect on Q4 events in particular.The so-called quadrupole statistical model for coherent structures in the whole TBL is verified Meanwhile,their spatial conditional-averaged topological shapes and the spatial scales of quadrupole coherent vortex structures as a whole in the overlying turbulent fl w over riblets are changed,suggesting that the riblets dampen the momentum and energy exchange between the regions of near-wall and outer portion of the TBL by depressing the bursting events（Q2 and Q4）,thereby reducing the skin friction drag.