An advantageous porous architecture of electrodes is pivotal in significantly enhancing alkaline water electrolysis(AWE)efficiency by optimizing the mass transport mechanisms.This effect becomes even more pronounced w...An advantageous porous architecture of electrodes is pivotal in significantly enhancing alkaline water electrolysis(AWE)efficiency by optimizing the mass transport mechanisms.This effect becomes even more pronounced when aiming to achieve elevated current densities.Herein,we employed a rapid and scalable laser texturing process to craft novel multi-channel porous electrodes.Particularly,the obtained electrodes exhibit the lowest Tafel slope of 79 mV dec^(-1)(HER)and 49 mV dec^(-1)(OER).As anticipated,the alkaline electrolyzer(AEL)cell incorporating multi-channel porous electrodes(NP-LT30)exhibited a remarkable improvement in cell efficiency,with voltage drops(from 2.28 to 1.97 V)exceeding 300 mV under 1 A cm^(-1),compared to conventional perforated Ni plate electrodes.This enhancement mainly stemmed from the employed multi-channel porous structure,facilitating mass transport and bubble dynamics through an innovative convection mode,surpassing the traditional convection mode.Furthermore,the NP-LT30-based AEL cell demonstrated exceptional durability for 300 h under 1.0 A cm^(-2).This study underscores the capability of the novel multi-channel porous electrodes to expedite mass transport in practical AWE applications.展开更多
Cold-junction compensation(CJC)and disconnection detection circuit design of various thermocouples(TC)and multi-channel TC interface circuits were designed.The CJC and disconnection detection circuit consists of a CJC...Cold-junction compensation(CJC)and disconnection detection circuit design of various thermocouples(TC)and multi-channel TC interface circuits were designed.The CJC and disconnection detection circuit consists of a CJC semiconductor device,an instrumentation amplifier(IA),two resistors,and a diode for disconnection detection.Based on the basic circuit,a multi-channel interface circuit was also implemented.The CJC was implemented using compensation semiconductor and IA,and disconnection detection was detected by using two resistors and a diode so that IA input voltage became-0.42 V.As a result of the experiment using R-type TC,the error of the designed circuit was reduced from 0.14 mV to 3μV after CJC in the temperature range of 0°C to 1400°C.In addition,it was confirmed that the output voltage of IA was saturated from 88 mV to-14.2 V when TC was disconnected from normal.The output voltage of the designed circuit was 0 V to 10 V in the temperature range of 0°C to 1400°C.The results of the 4-channel interface experiment using R-type TC were almost identical to the CJC and disconnection detection results for each channel.The implemented multi-channel interface has a feature that can be applied equally to E,J,K,T,R,and S-type TCs by changing the terminals of CJC semiconductor devices and adjusting the IA gain.展开更多
Most of existing metasurfaces usually have limited channel behavior,which seriouslyhinders their development and application.In this paper,we propose a multi-channel terahertz focused beam generator based on shared-ap...Most of existing metasurfaces usually have limited channel behavior,which seriouslyhinders their development and application.In this paper,we propose a multi-channel terahertz focused beam generator based on shared-aperture metasurface,and the generator consists of a top square metal strip,a middle layer of silica and a metal bottom plate.By changing the position and size of the shared-aperture array,the designed metasurface can generate any number of multi-channel focusing beams at different predicted positions.In addition,the energy intensity of focusing beams can be controlled.The full-wave simulation results show that the metasurface achieves four-channel vortex focused beam generation with different topological charges,and five-,six-,eight-channel focused beam generation with different energy intensities at a frequency of 1 THz,which are in good agreement with the theoretically calculated predictions.This work can provide a new idea for designing the terahertz multichannel devices.展开更多
Classical multi-channel technology can significantly reduce the pre-stack seismic inversion uncertainty, especially for complex geology such as high dipping structures. However, due to the consideration of complex str...Classical multi-channel technology can significantly reduce the pre-stack seismic inversion uncertainty, especially for complex geology such as high dipping structures. However, due to the consideration of complex structure or reflection features, the existing multi-channel inversion methods have to adopt the highly time-consuming strategy of arranging seismic data trace-by-trace, limiting its wide application in pre-stack inversion. A fast pre-stack multi-channel inversion constrained by seismic reflection features has been proposed to address this issue. The key to our method is to re-characterize the reflection features to directly constrain the pre-stack inversion through a Hadamard product operator without rearranging the seismic data. The seismic reflection features can reflect the distribution of the stratum reflection interface, and we obtained them from the post-stack profile by searching the shortest local Euclidean distance between adjacent seismic traces. Instead of directly constructing a large-size reflection features constraint operator advocated by the conventional methods, through decomposing the reflection features along the vertical and horizontal direction at a particular sampling point, we have constructed a computationally well-behaved constraint operator represented by the vertical and horizontal partial derivatives. Based on the Alternating Direction Method of Multipliers (ADMM) optimization, we have derived a fast algorithm for solving the objective function, including Hadamard product operators. Compared with the conventional reflection features constrained inversion, the proposed method is more efficient and accurate, proved on the Overthrust model and a field data set.展开更多
Due to the scattered nature of the network,data transmission in a dis-tributed Mobile Ad-hoc Network(MANET)consumes more energy resources(ER)than in a centralized network,resulting in a shorter network lifespan(NL).As...Due to the scattered nature of the network,data transmission in a dis-tributed Mobile Ad-hoc Network(MANET)consumes more energy resources(ER)than in a centralized network,resulting in a shorter network lifespan(NL).As a result,we build an Enhanced Opportunistic Routing(EORP)protocol architecture in order to address the issues raised before.This proposed routing protocol goal is to manage the routing cost by employing power,load,and delay to manage the routing energy consumption based on theflooding of control pack-ets from the target node.According to the goal of the proposed protocol techni-que,it is possible to manage the routing cost by applying power,load,and delay.The proposed technique also manage the routing energy consumption based on theflooding of control packets from the destination node in order to reduce the routing cost.Control packet exchange between the target and all the nodes,on the other hand,is capable of having an influence on the overall efficiency of the system.The EORP protocol and the Multi-channel Cooperative Neighbour Discovery(MCCND)protocol have been designed to detect the cooperative adja-cent nodes for each node in the routing route as part of the routing path discovery process,which occurs during control packet transmission.While control packet transmission is taking place during the routing path discovery process,the EORP protocol and the Multi-channel Cooperative Neighbour Discovery(MCCND)protocol have been designed to detect the cooperative adjacent nodes for each node in the routing.Also included is a simulation of these protocols in order to evaluate their performance across a wide range of packet speeds using Constant Bit Rate(CBR).When the packet rate of the CBR is 20 packets per second,the results reveal that the EORP-MCCND is 0.6 s quicker than the state-of-the-art protocols,according to thefindings.Assuming that the CBR packet rate is 20 packets per second,the EORP-MCCND achieves 0.6 s of End 2 End Delay,0.05 s of Routing Overhead Delay,120 s of Network Lifetime,and 20 J of Energy Consumption efficiency,which is much better than that of the state-of-the-art protocols.展开更多
With the growth of requirements for data sharing,a novel business model of digital assets trading has emerged that allows data owners to sell their data for monetary gain.In the distributed ledger of blockchain,howeve...With the growth of requirements for data sharing,a novel business model of digital assets trading has emerged that allows data owners to sell their data for monetary gain.In the distributed ledger of blockchain,however,the privacy of stakeholder's identity and the confidentiality of data content are threatened.Therefore,we proposed a blockchainenabled privacy-preserving and access control scheme to address the above problems.First,the multi-channel mechanism is introduced to provide the privacy protection of distributed ledger inside the channel and achieve coarse-grained access control to digital assets.Then,we use multi-authority attribute-based encryption(MAABE)algorithm to build a fine-grained access control model for data trading in a single channel and describe its instantiation in detail.Security analysis shows that the scheme has IND-CPA secure and can provide privacy protection and collusion resistance.Compared with other schemes,our solution has better performance in privacy protection and access control.The evaluation results demonstrate its effectiveness and practicability.展开更多
A new muon beam facility,called the Experimental Muon Source(EMuS),was proposed for construction at the China Spallation Neutron Source(CSNS).The design of the complex muon beamlines for the EMuS baseline scheme,which...A new muon beam facility,called the Experimental Muon Source(EMuS),was proposed for construction at the China Spallation Neutron Source(CSNS).The design of the complex muon beamlines for the EMuS baseline scheme,which is based on superconducting solenoids,superferric dipoles and room-temperature magnets,is presented herein.Various muon beams,including surface muons,decay muons and low energy muons,have been developed for multipurpose applications.The optics design and simulation results of the trunk beamline and branch beamlines are presented.With a proton beam power of 25 kW at a standalone target station that consists of a conical graphite target and high-field superconducting solenoids,the muon beam intensity in the trunk beamline varies from 10^(7)/s for surface muons to 10^(10)/s for high-momentum decay muons.And at the endstations,these values vary from 10^(5)/s for surface muons to 10^(8)/s for decay muons.展开更多
Steel-concrete composite structures(SCCS)have been widely used as primary load-bearing components in large-scale civil infrastructures.As the basis of the co-working ability of steel plate and concrete,the bonding sta...Steel-concrete composite structures(SCCS)have been widely used as primary load-bearing components in large-scale civil infrastructures.As the basis of the co-working ability of steel plate and concrete,the bonding status plays an essential role in guaranteeing the structural performance of SCCS.Accordingly,efficient non-destructive testing(NDT)on interfacial debondings in SCCS has become a prominent research area.Multi-channel analysis of surface waves(MASW)has been validated as an effective NDT technique for interfacial debonding detection for SCCS.However,the feasibility of MASW must be validated using experimental measurements.This study establishes a high-frequency data synchronous acquisition system with 32 channels to perform comparative verification experiments in depth.First,the current sensing approaches for high-frequency vibration and stress waves are summarized.Secondly,three types of contact sensors,namely,piezoelectric lead-zirconate-titanate(PZT)patches,accelerometers,and ultrasonic transducers,are selected for MASW measurement.Then,the selection and optimization of the force hammer head are performed.Comparative experiments are carried out for the optimal selection of ultrasonic transducers,PZT patches,and accelerometers for MASW measurement.In addition,the influence of different pasting methods on the output signal of the sensor array is discussed.Experimental results indicate that optimized PZT patches,acceleration sensors,and ultrasonic transducers can provide efficient data acquisition for MASW-based non-destructive experiments.The research findings in this study lay a solid foundation for analyzing the recognition accuracy of contact MASW measurement using different sensor arrays.展开更多
为降低通信冲突和信道干扰,对Mult-i Radio Mult-i Channel传感器网络无冲突信道进行研究,结果证实在网络通信半径大于3倍的网络最大功率通信半径的前提下,Sensor节点规模满足2倍网络功率级数加1的环境下,网络无冲突信道分配的信道数达...为降低通信冲突和信道干扰,对Mult-i Radio Mult-i Channel传感器网络无冲突信道进行研究,结果证实在网络通信半径大于3倍的网络最大功率通信半径的前提下,Sensor节点规模满足2倍网络功率级数加1的环境下,网络无冲突信道分配的信道数达到网络信道冲突图的最大值。文章通过对无冲突信道算法的运用,最终证实其可以有效地提高传感器网络的工作效率,大幅度提升网络的吞吐量。展开更多
An individual’s self-image is a multi-dimensional and multi-structural concept.Its internal dimensions include ability,knowledge,values,personality,and temperament,and its external dimensions are physical appearance,...An individual’s self-image is a multi-dimensional and multi-structural concept.Its internal dimensions include ability,knowledge,values,personality,and temperament,and its external dimensions are physical appearance,behavior,and clothing.A good image will have a positive impact both in life and at work.We will choose appropriate clothing and makeup to modify the external image and cultivate positive qualities such as correct values and an optimistic attitude towards life to enhance internal dimensions.Among them,“personality”and“ability”mostly belong to the research category of mental health education,and“values”fit in the research field of ideological and political education.Ideological and political education and mental health education are both important components of higher education,which show similarities between them.Ideological and political education and mental health education can complement each other in many ways to enhance students’self-image.展开更多
The construction of modern livable cities faces challenges in karst areas,including ground collapse and engineering problems.Wuhan,with a population of 13.74×10^(6) and approximately 1161 km^(2)of soluble rocks i...The construction of modern livable cities faces challenges in karst areas,including ground collapse and engineering problems.Wuhan,with a population of 13.74×10^(6) and approximately 1161 km^(2)of soluble rocks in the urban area of 8569.15 km^(2),predominantly consists of concealed karst areas where occasional ground collapse events occur,posing significant threats to underground engineering projects.To address these challenges,a comprehensive geological survey was conducted in Wuhan,focusing on major karstrelated issues.Geophysical methods offer advantages over drilling in detecting concealed karst areas due to their efficiency,non-destructiveness,and flexibility.This paper reviewed the karst geological characteristics in Wuhan and the geophysical exploration methods for karst,selected eight effective geophysical methods for field experimentation,evaluated their suitability,and proposed method combinations for different karst scenarios.The results show that different geophysical methods have varying applicability for karst detection in Wuhan,and combining multiple methods enhances detection effectiveness.The specific recommendations for method combinations provided in this study serve as a valuable reference for karst detection in Wuhan.展开更多
In traditional universal asynchronous receiver transmitter (UART) controller, the data transmission is inefficient and the data bus utilization ratio is low. A novel design is provided to solve these problems. The a...In traditional universal asynchronous receiver transmitter (UART) controller, the data transmission is inefficient and the data bus utilization ratio is low. A novel design is provided to solve these problems. The architecture of the system is introduced, the flow charts of data processing as well as the implementation state machine are also presented in detail. This paper is concluded by comparing the performance of this design, which is realized on field programmable gate army (FPGA) using Verilog hardware description language (HDL), with other traditional UART controllers.展开更多
The problem of two order statistics detection schemes for the detection of a spatially distributed target in white Gaussian noise are studied.When the number of strong scattering cells is known,we first show an optima...The problem of two order statistics detection schemes for the detection of a spatially distributed target in white Gaussian noise are studied.When the number of strong scattering cells is known,we first show an optimal detector,which requires many processing channels.The structure of such optimal detector is complex.Therefore,a simpler quasi-optimal detector is then introduced.The quasi-optimal detector,called the strong scattering cells’ number dependent order statistics(SND-OS) detector,takes the form of an average of maximum strong scattering cells with a known number.If the number of strong scattering cells is unknown in real situation,the multi-channel order statistics(MC-OS) detector is used.In each channel,a various number of maximums scattered from target are averaged.Then,the false alarm probability analysis and thresholds sets for each channel are given,following the detection results presented by means of Monte Carlo simulation strategy based on simulated target model and three measured targets.In particular,the theoretical analysis and simulation results highlight that the MC-OS detector can efficiently detect range-spread targets in white Gaussian noise.展开更多
A conventional multi-channel pulse amplitude analyzer acquires single energy spectrum,but provides no information on its tendency with time.To address the limitation,we propose a scheme of time-sharing multichannel pu...A conventional multi-channel pulse amplitude analyzer acquires single energy spectrum,but provides no information on its tendency with time.To address the limitation,we propose a scheme of time-sharing multichannel pulse amplitude analyzer(TSMCA).A dual-port random access memory is divided into two storage spaces,one for current energy spectrum data acquisition and another for previous energy spectrum data storage.The two tasks can be performed simultaneously,and the time-related variation tendency of energy spectrum can be obtained.A prototype system of TSMCA is designed.It performs nicely,with maximum channel number of 4096 in capacity of 2^(32)/Ch,minimal time-sharing slice of 25 ms,the differential nonlinearity of <1.5%,and the integral nonlinearity of <0.3%.展开更多
This paper investigates the receding horizon state estimation for the linear discrete-time system with multi-channel observation delays. The receding horizon estimation is designed by the reorganized observation techn...This paper investigates the receding horizon state estimation for the linear discrete-time system with multi-channel observation delays. The receding horizon estimation is designed by the reorganized observation technique and the linear unbiased estimation method. The estimation gains are developed by solving a set of Riccati equations, and a stability result about the state estimation is shown. Finally, an example is given to illustrate the efficiency of the receding horizon state estimation.展开更多
A multi-gap and multi-channel gas switch with convexo-convex discal planet electrodes was designed and investigated. Eight gaps are formed in series by a trigger electrode, six intermediate electrodes and two high vol...A multi-gap and multi-channel gas switch with convexo-convex discal planet electrodes was designed and investigated. Eight gaps are formed in series by a trigger electrode, six intermediate electrodes and two high voltage electrodes with a uniform gap length of 5 ram. The self breakdown and triggered breakdown performance of the switch are reported. Both the delay time and jitter decrease with the increase in the trigger voltage, switching coefficient and the decrease in the trigger isolating resistor. The delay time of the switch is about 40 ns, and the jitter is less than 2 ns when charged with 4-85 kV and triggered by a voltage pule of -75 kV. The inductance of the switch is about 30 nH.展开更多
To study multi-radio multi-channel (MR-MC) Ad Hoc networks based on 802.11, an efficient cross-layer routing protocol with the function of joint channel assignment, called joint channel assignment and cross-layer ro...To study multi-radio multi-channel (MR-MC) Ad Hoc networks based on 802.11, an efficient cross-layer routing protocol with the function of joint channel assignment, called joint channel assignment and cross-layer routing (JCACR), is presented. Firstly, this paper introduces a new concept called channel utilization percentage (CUP), which is for measuring the contention level of different channels in a node’s neighborhood, and deduces its optimal value for determining whether a channel is overloaded or not. Then, a metric parameter named channel selection metric (CSM) is designed, which actually reffects not only the channel status but also corresponding node’s capacity to seize it. JCACR evaluates channel assignment by CSM, performs a local optimization by assigning each node a channel with the smaller CSM value, and changes the working channel dynamically when the channel is overloaded. Therefore, the network load balancing can be achieved. In addition, simulation shows that, when compared with the protocol of weighted cumulative expected transfer time (WCETT), the new protocol can improve the network throughput and reduce the end-to-end average delay with fewer overheads.展开更多
We propose and experimentally demonstrate an integrated silicon photonic scheme to generate multi-channel millimeter-wave(MMW) signals for 5 G multi-user applications. The fabricated silicon photonic chip has a footpr...We propose and experimentally demonstrate an integrated silicon photonic scheme to generate multi-channel millimeter-wave(MMW) signals for 5 G multi-user applications. The fabricated silicon photonic chip has a footprint of 1.1 × 2.1 mm^2 and integrates 7 independent channels each having on-chip polarization control and heterodyne mixing functions. 7 channels of4-Gb/s QPSK baseband signals are delivered via a 2-km multi-core fiber(MCF) and coupled into the chip with a local oscillator(LO) light. The polarization state of each signal light is automatically adjusted and aligned with that of the LO light, and then 7 channels of 28-GHz MMW carrying 4-Gb/s QPSK signals are generated by optical heterodyne beating. Automated polarizationcontrol function of each channel is also demonstrated with ~7-ms tuning time and ~27-dB extinction ratio.展开更多
A data acquisition system (DAS) to implement high-speed, real-time and multi-channel data acquisition and store is presented. The control of the system is implemented by the combination of complex programable logic ...A data acquisition system (DAS) to implement high-speed, real-time and multi-channel data acquisition and store is presented. The control of the system is implemented by the combination of complex programable logic device (CPLD) and digital signal processing (DSP), the bulk buffer of the system is implemented by the combination of CPLD, DSP, and synchronous dynamic random access memory (SDRAM), and the data transfer is implemented by the combination of DSP, first in first out (FIFO), universal serial bus (USB) and USB hub. The system could not only work independently in single-channel mode, but also implement high-speed real-time multi-channel data acquisition system (MCDAS) by the combination of multiple single-channels. The sampling rate and data storage capacity of each channel could reach up to 100 million sampiing per second and 256 MB respectively.展开更多
There are well-established chemical and turbidity anomalies in the plumes occurring vicinity of hydrothermal vents, which are used to indicate their existence and locations. We here develop a small, accurate multi-cha...There are well-established chemical and turbidity anomalies in the plumes occurring vicinity of hydrothermal vents, which are used to indicate their existence and locations. We here develop a small, accurate multi-channel chemical sensor to detect such anomalies which can be used in deep-sea at depths of more than 4 000 m. The design allowed five all-solid-state electrodes to be mounted on it and each (apart from one reference electrode) could be changed according to chemicals to be measured. Two experiments were conducted using the chemical sensors. The first was a shallow-sea trial which included sample measurements and in situ monitoring. pH, Eh, CO3^2- and SO4^2- electrodes were utilized to demonstrate that the chemical sensor was accurate and stable outside the laboratory. In the second experiment, the chemical sensor was integrated with pH, Eh, CO3^2- and H2S electrodes, and was used in 29 scans of the seabed along the Southwest Indian Ridge (SWIR) to detect hydrothermal vents, from which 27 sets of valid data were obtained. Hydrothermal vents were identified by analyzing the chemical anomalies, the primary judging criteria were decreasing voltages of Eh and H2S, matched by increasing voltages of pH and CO3^2- . We proposed that simultaneous detection of changes in these parameters will indicate a hydrothermal vent. Amongst the 27 valid sets of data, five potential hydrothermal vents were targeted using the proposed method. We suggest that our sensors could be widely employed by marine scientists.展开更多
基金financial support from the National Key R&D Program(2023YFE0108000)the Academy of Sciences Project of Guangdong Province(2019GDASYL-0102007,2021GDASYL-20210103063)+1 种基金GDAS’Project of Science and Technology Development(2022GDASZH-2022010203-003)financial support from the China Scholarship Council(202108210128)。
文摘An advantageous porous architecture of electrodes is pivotal in significantly enhancing alkaline water electrolysis(AWE)efficiency by optimizing the mass transport mechanisms.This effect becomes even more pronounced when aiming to achieve elevated current densities.Herein,we employed a rapid and scalable laser texturing process to craft novel multi-channel porous electrodes.Particularly,the obtained electrodes exhibit the lowest Tafel slope of 79 mV dec^(-1)(HER)and 49 mV dec^(-1)(OER).As anticipated,the alkaline electrolyzer(AEL)cell incorporating multi-channel porous electrodes(NP-LT30)exhibited a remarkable improvement in cell efficiency,with voltage drops(from 2.28 to 1.97 V)exceeding 300 mV under 1 A cm^(-1),compared to conventional perforated Ni plate electrodes.This enhancement mainly stemmed from the employed multi-channel porous structure,facilitating mass transport and bubble dynamics through an innovative convection mode,surpassing the traditional convection mode.Furthermore,the NP-LT30-based AEL cell demonstrated exceptional durability for 300 h under 1.0 A cm^(-2).This study underscores the capability of the novel multi-channel porous electrodes to expedite mass transport in practical AWE applications.
文摘Cold-junction compensation(CJC)and disconnection detection circuit design of various thermocouples(TC)and multi-channel TC interface circuits were designed.The CJC and disconnection detection circuit consists of a CJC semiconductor device,an instrumentation amplifier(IA),two resistors,and a diode for disconnection detection.Based on the basic circuit,a multi-channel interface circuit was also implemented.The CJC was implemented using compensation semiconductor and IA,and disconnection detection was detected by using two resistors and a diode so that IA input voltage became-0.42 V.As a result of the experiment using R-type TC,the error of the designed circuit was reduced from 0.14 mV to 3μV after CJC in the temperature range of 0°C to 1400°C.In addition,it was confirmed that the output voltage of IA was saturated from 88 mV to-14.2 V when TC was disconnected from normal.The output voltage of the designed circuit was 0 V to 10 V in the temperature range of 0°C to 1400°C.The results of the 4-channel interface experiment using R-type TC were almost identical to the CJC and disconnection detection results for each channel.The implemented multi-channel interface has a feature that can be applied equally to E,J,K,T,R,and S-type TCs by changing the terminals of CJC semiconductor devices and adjusting the IA gain.
基金Project supported by the National Natural Science Foundation of China (Grant No.62271460)the Zhejiang Key Research and Development Project,China (Grant Nos.2021C03153 and 2022C03166)。
文摘Most of existing metasurfaces usually have limited channel behavior,which seriouslyhinders their development and application.In this paper,we propose a multi-channel terahertz focused beam generator based on shared-aperture metasurface,and the generator consists of a top square metal strip,a middle layer of silica and a metal bottom plate.By changing the position and size of the shared-aperture array,the designed metasurface can generate any number of multi-channel focusing beams at different predicted positions.In addition,the energy intensity of focusing beams can be controlled.The full-wave simulation results show that the metasurface achieves four-channel vortex focused beam generation with different topological charges,and five-,six-,eight-channel focused beam generation with different energy intensities at a frequency of 1 THz,which are in good agreement with the theoretically calculated predictions.This work can provide a new idea for designing the terahertz multichannel devices.
基金We would like to acknowledge the sponsorship of the National Natural Science Foundation of China(42004092,42030103,41974119)Marine S&T Fund of Shandong Province for Pilot National Laboratory for Marine Science and Technology(Qingdao)(Grant No.2021QNLM020001-6)Young Elite Scientists Sponsorship Program by CAST(2021QNRC001).
文摘Classical multi-channel technology can significantly reduce the pre-stack seismic inversion uncertainty, especially for complex geology such as high dipping structures. However, due to the consideration of complex structure or reflection features, the existing multi-channel inversion methods have to adopt the highly time-consuming strategy of arranging seismic data trace-by-trace, limiting its wide application in pre-stack inversion. A fast pre-stack multi-channel inversion constrained by seismic reflection features has been proposed to address this issue. The key to our method is to re-characterize the reflection features to directly constrain the pre-stack inversion through a Hadamard product operator without rearranging the seismic data. The seismic reflection features can reflect the distribution of the stratum reflection interface, and we obtained them from the post-stack profile by searching the shortest local Euclidean distance between adjacent seismic traces. Instead of directly constructing a large-size reflection features constraint operator advocated by the conventional methods, through decomposing the reflection features along the vertical and horizontal direction at a particular sampling point, we have constructed a computationally well-behaved constraint operator represented by the vertical and horizontal partial derivatives. Based on the Alternating Direction Method of Multipliers (ADMM) optimization, we have derived a fast algorithm for solving the objective function, including Hadamard product operators. Compared with the conventional reflection features constrained inversion, the proposed method is more efficient and accurate, proved on the Overthrust model and a field data set.
文摘Due to the scattered nature of the network,data transmission in a dis-tributed Mobile Ad-hoc Network(MANET)consumes more energy resources(ER)than in a centralized network,resulting in a shorter network lifespan(NL).As a result,we build an Enhanced Opportunistic Routing(EORP)protocol architecture in order to address the issues raised before.This proposed routing protocol goal is to manage the routing cost by employing power,load,and delay to manage the routing energy consumption based on theflooding of control pack-ets from the target node.According to the goal of the proposed protocol techni-que,it is possible to manage the routing cost by applying power,load,and delay.The proposed technique also manage the routing energy consumption based on theflooding of control packets from the destination node in order to reduce the routing cost.Control packet exchange between the target and all the nodes,on the other hand,is capable of having an influence on the overall efficiency of the system.The EORP protocol and the Multi-channel Cooperative Neighbour Discovery(MCCND)protocol have been designed to detect the cooperative adja-cent nodes for each node in the routing route as part of the routing path discovery process,which occurs during control packet transmission.While control packet transmission is taking place during the routing path discovery process,the EORP protocol and the Multi-channel Cooperative Neighbour Discovery(MCCND)protocol have been designed to detect the cooperative adjacent nodes for each node in the routing.Also included is a simulation of these protocols in order to evaluate their performance across a wide range of packet speeds using Constant Bit Rate(CBR).When the packet rate of the CBR is 20 packets per second,the results reveal that the EORP-MCCND is 0.6 s quicker than the state-of-the-art protocols,according to thefindings.Assuming that the CBR packet rate is 20 packets per second,the EORP-MCCND achieves 0.6 s of End 2 End Delay,0.05 s of Routing Overhead Delay,120 s of Network Lifetime,and 20 J of Energy Consumption efficiency,which is much better than that of the state-of-the-art protocols.
基金supported by National Key Research and Development Plan in China(Grant No.2020YFB1005500)Beijing Natural Science Foundation(Grant No.M21034)BUPT Excellent Ph.D Students Foundation(Grant No.CX2023218)。
文摘With the growth of requirements for data sharing,a novel business model of digital assets trading has emerged that allows data owners to sell their data for monetary gain.In the distributed ledger of blockchain,however,the privacy of stakeholder's identity and the confidentiality of data content are threatened.Therefore,we proposed a blockchainenabled privacy-preserving and access control scheme to address the above problems.First,the multi-channel mechanism is introduced to provide the privacy protection of distributed ledger inside the channel and achieve coarse-grained access control to digital assets.Then,we use multi-authority attribute-based encryption(MAABE)algorithm to build a fine-grained access control model for data trading in a single channel and describe its instantiation in detail.Security analysis shows that the scheme has IND-CPA secure and can provide privacy protection and collusion resistance.Compared with other schemes,our solution has better performance in privacy protection and access control.The evaluation results demonstrate its effectiveness and practicability.
基金supported by the National Natural Science Foundation of China(Nos.11527811 and 12035017).
文摘A new muon beam facility,called the Experimental Muon Source(EMuS),was proposed for construction at the China Spallation Neutron Source(CSNS).The design of the complex muon beamlines for the EMuS baseline scheme,which is based on superconducting solenoids,superferric dipoles and room-temperature magnets,is presented herein.Various muon beams,including surface muons,decay muons and low energy muons,have been developed for multipurpose applications.The optics design and simulation results of the trunk beamline and branch beamlines are presented.With a proton beam power of 25 kW at a standalone target station that consists of a conical graphite target and high-field superconducting solenoids,the muon beam intensity in the trunk beamline varies from 10^(7)/s for surface muons to 10^(10)/s for high-momentum decay muons.And at the endstations,these values vary from 10^(5)/s for surface muons to 10^(8)/s for decay muons.
基金National Natural Science Foundation of China under Grant (Nos.52192662,52020105005,51908320)the Beijing Nova Program under Grant No.20220484012+1 种基金the Interdisciplinary Research Project for Young Teachers of USTB (Fundamental Research Funds for the Central Universities,FRF-IDRY-22-013)the Key Laboratory for Intelligent Infrastructure and Monitoring of Fujian Province (Huaqiao University,IIM-01-05)。
文摘Steel-concrete composite structures(SCCS)have been widely used as primary load-bearing components in large-scale civil infrastructures.As the basis of the co-working ability of steel plate and concrete,the bonding status plays an essential role in guaranteeing the structural performance of SCCS.Accordingly,efficient non-destructive testing(NDT)on interfacial debondings in SCCS has become a prominent research area.Multi-channel analysis of surface waves(MASW)has been validated as an effective NDT technique for interfacial debonding detection for SCCS.However,the feasibility of MASW must be validated using experimental measurements.This study establishes a high-frequency data synchronous acquisition system with 32 channels to perform comparative verification experiments in depth.First,the current sensing approaches for high-frequency vibration and stress waves are summarized.Secondly,three types of contact sensors,namely,piezoelectric lead-zirconate-titanate(PZT)patches,accelerometers,and ultrasonic transducers,are selected for MASW measurement.Then,the selection and optimization of the force hammer head are performed.Comparative experiments are carried out for the optimal selection of ultrasonic transducers,PZT patches,and accelerometers for MASW measurement.In addition,the influence of different pasting methods on the output signal of the sensor array is discussed.Experimental results indicate that optimized PZT patches,acceleration sensors,and ultrasonic transducers can provide efficient data acquisition for MASW-based non-destructive experiments.The research findings in this study lay a solid foundation for analyzing the recognition accuracy of contact MASW measurement using different sensor arrays.
文摘为降低通信冲突和信道干扰,对Mult-i Radio Mult-i Channel传感器网络无冲突信道进行研究,结果证实在网络通信半径大于3倍的网络最大功率通信半径的前提下,Sensor节点规模满足2倍网络功率级数加1的环境下,网络无冲突信道分配的信道数达到网络信道冲突图的最大值。文章通过对无冲突信道算法的运用,最终证实其可以有效地提高传感器网络的工作效率,大幅度提升网络的吞吐量。
基金Sichuan Provincial Key Research Base for Philosophy and Social Sciences,Mental Health Education Research Project“Research on Self-Image Cognition Improvement Strategies of Higher Vocational Students Under the Background of Ideological and Political Education in Colleges and Universities”(XLJKJY202114C)。
文摘An individual’s self-image is a multi-dimensional and multi-structural concept.Its internal dimensions include ability,knowledge,values,personality,and temperament,and its external dimensions are physical appearance,behavior,and clothing.A good image will have a positive impact both in life and at work.We will choose appropriate clothing and makeup to modify the external image and cultivate positive qualities such as correct values and an optimistic attitude towards life to enhance internal dimensions.Among them,“personality”and“ability”mostly belong to the research category of mental health education,and“values”fit in the research field of ideological and political education.Ideological and political education and mental health education are both important components of higher education,which show similarities between them.Ideological and political education and mental health education can complement each other in many ways to enhance students’self-image.
基金jointly supported by the project of Chinese National Natural Science Foundation(42107485)National Key R&D Program(2020YFC1512400,2018YFC800804)China Geological Survey(DD20190282,DD20221734,and DD20230323)。
文摘The construction of modern livable cities faces challenges in karst areas,including ground collapse and engineering problems.Wuhan,with a population of 13.74×10^(6) and approximately 1161 km^(2)of soluble rocks in the urban area of 8569.15 km^(2),predominantly consists of concealed karst areas where occasional ground collapse events occur,posing significant threats to underground engineering projects.To address these challenges,a comprehensive geological survey was conducted in Wuhan,focusing on major karstrelated issues.Geophysical methods offer advantages over drilling in detecting concealed karst areas due to their efficiency,non-destructiveness,and flexibility.This paper reviewed the karst geological characteristics in Wuhan and the geophysical exploration methods for karst,selected eight effective geophysical methods for field experimentation,evaluated their suitability,and proposed method combinations for different karst scenarios.The results show that different geophysical methods have varying applicability for karst detection in Wuhan,and combining multiple methods enhances detection effectiveness.The specific recommendations for method combinations provided in this study serve as a valuable reference for karst detection in Wuhan.
基金National Natural Science Foundation of China (60532030)
文摘In traditional universal asynchronous receiver transmitter (UART) controller, the data transmission is inefficient and the data bus utilization ratio is low. A novel design is provided to solve these problems. The architecture of the system is introduced, the flow charts of data processing as well as the implementation state machine are also presented in detail. This paper is concluded by comparing the performance of this design, which is realized on field programmable gate army (FPGA) using Verilog hardware description language (HDL), with other traditional UART controllers.
基金supported by the Major Program of National Natural Science Foundation of China (10990012)the National Natural Science Foundation of China (61201296,61271024)+1 种基金the Fundamental Research Funds for the Central Universities (K5051202037)Guangxi Key Lab of Wireless Wideband Communication & Signal Processing (12205)
文摘The problem of two order statistics detection schemes for the detection of a spatially distributed target in white Gaussian noise are studied.When the number of strong scattering cells is known,we first show an optimal detector,which requires many processing channels.The structure of such optimal detector is complex.Therefore,a simpler quasi-optimal detector is then introduced.The quasi-optimal detector,called the strong scattering cells’ number dependent order statistics(SND-OS) detector,takes the form of an average of maximum strong scattering cells with a known number.If the number of strong scattering cells is unknown in real situation,the multi-channel order statistics(MC-OS) detector is used.In each channel,a various number of maximums scattered from target are averaged.Then,the false alarm probability analysis and thresholds sets for each channel are given,following the detection results presented by means of Monte Carlo simulation strategy based on simulated target model and three measured targets.In particular,the theoretical analysis and simulation results highlight that the MC-OS detector can efficiently detect range-spread targets in white Gaussian noise.
基金supported by the National Natural Science Foundation of China(Nos.11375195,11375263,and 11105143)the project of National Magnetic Confinement Fusion Energy Development Research(No.2013GB104003)
文摘A conventional multi-channel pulse amplitude analyzer acquires single energy spectrum,but provides no information on its tendency with time.To address the limitation,we propose a scheme of time-sharing multichannel pulse amplitude analyzer(TSMCA).A dual-port random access memory is divided into two storage spaces,one for current energy spectrum data acquisition and another for previous energy spectrum data storage.The two tasks can be performed simultaneously,and the time-related variation tendency of energy spectrum can be obtained.A prototype system of TSMCA is designed.It performs nicely,with maximum channel number of 4096 in capacity of 2^(32)/Ch,minimal time-sharing slice of 25 ms,the differential nonlinearity of <1.5%,and the integral nonlinearity of <0.3%.
基金supported by National Natural Science Foundation of China(61473134,61573220)the Postdoctoral Science Foundation of China(2017M622231)
文摘This paper investigates the receding horizon state estimation for the linear discrete-time system with multi-channel observation delays. The receding horizon estimation is designed by the reorganized observation technique and the linear unbiased estimation method. The estimation gains are developed by solving a set of Riccati equations, and a stability result about the state estimation is shown. Finally, an example is given to illustrate the efficiency of the receding horizon state estimation.
基金supported by National Natural Science Foundation of China(Nos.50477019,50637010)the State Key Laboratory of Electrical Insulation and Power Equipment of China(EIPE.09207)
文摘A multi-gap and multi-channel gas switch with convexo-convex discal planet electrodes was designed and investigated. Eight gaps are formed in series by a trigger electrode, six intermediate electrodes and two high voltage electrodes with a uniform gap length of 5 ram. The self breakdown and triggered breakdown performance of the switch are reported. Both the delay time and jitter decrease with the increase in the trigger voltage, switching coefficient and the decrease in the trigger isolating resistor. The delay time of the switch is about 40 ns, and the jitter is less than 2 ns when charged with 4-85 kV and triggered by a voltage pule of -75 kV. The inductance of the switch is about 30 nH.
基金supported by the National Natural Science Foundationof China (60873195 61070220)+3 种基金the Natural Science Foundation of Anhui Province (070412049)the Outstanding Young Teacher Foundation of Anhui Higher Education Institutions of China (2009SQRZ167)the Natural Science Foundation of Anhui Higher Education Institutions of China (KJ2009B114)the Open Project Program of Engineering Research Center of Safety Critical Industry Measure and Control Technology (SCIMCT0802)
文摘To study multi-radio multi-channel (MR-MC) Ad Hoc networks based on 802.11, an efficient cross-layer routing protocol with the function of joint channel assignment, called joint channel assignment and cross-layer routing (JCACR), is presented. Firstly, this paper introduces a new concept called channel utilization percentage (CUP), which is for measuring the contention level of different channels in a node’s neighborhood, and deduces its optimal value for determining whether a channel is overloaded or not. Then, a metric parameter named channel selection metric (CSM) is designed, which actually reffects not only the channel status but also corresponding node’s capacity to seize it. JCACR evaluates channel assignment by CSM, performs a local optimization by assigning each node a channel with the smaller CSM value, and changes the working channel dynamically when the channel is overloaded. Therefore, the network load balancing can be achieved. In addition, simulation shows that, when compared with the protocol of weighted cumulative expected transfer time (WCETT), the new protocol can improve the network throughput and reduce the end-to-end average delay with fewer overheads.
基金supported by the National Key R&D Pro-gram of China under Grant 2016YFB0402501in part by the Natural Science Foundation of China under grant 61605112Open Fund of IPOC under grant BUPT
文摘We propose and experimentally demonstrate an integrated silicon photonic scheme to generate multi-channel millimeter-wave(MMW) signals for 5 G multi-user applications. The fabricated silicon photonic chip has a footprint of 1.1 × 2.1 mm^2 and integrates 7 independent channels each having on-chip polarization control and heterodyne mixing functions. 7 channels of4-Gb/s QPSK baseband signals are delivered via a 2-km multi-core fiber(MCF) and coupled into the chip with a local oscillator(LO) light. The polarization state of each signal light is automatically adjusted and aligned with that of the LO light, and then 7 channels of 28-GHz MMW carrying 4-Gb/s QPSK signals are generated by optical heterodyne beating. Automated polarizationcontrol function of each channel is also demonstrated with ~7-ms tuning time and ~27-dB extinction ratio.
文摘A data acquisition system (DAS) to implement high-speed, real-time and multi-channel data acquisition and store is presented. The control of the system is implemented by the combination of complex programable logic device (CPLD) and digital signal processing (DSP), the bulk buffer of the system is implemented by the combination of CPLD, DSP, and synchronous dynamic random access memory (SDRAM), and the data transfer is implemented by the combination of DSP, first in first out (FIFO), universal serial bus (USB) and USB hub. The system could not only work independently in single-channel mode, but also implement high-speed real-time multi-channel data acquisition system (MCDAS) by the combination of multiple single-channels. The sampling rate and data storage capacity of each channel could reach up to 100 million sampiing per second and 256 MB respectively.
基金The Open Foundation of Laboratory of Marine Ecosystem and Biogeochemistry,SOA under contract No.LMEB201701
文摘There are well-established chemical and turbidity anomalies in the plumes occurring vicinity of hydrothermal vents, which are used to indicate their existence and locations. We here develop a small, accurate multi-channel chemical sensor to detect such anomalies which can be used in deep-sea at depths of more than 4 000 m. The design allowed five all-solid-state electrodes to be mounted on it and each (apart from one reference electrode) could be changed according to chemicals to be measured. Two experiments were conducted using the chemical sensors. The first was a shallow-sea trial which included sample measurements and in situ monitoring. pH, Eh, CO3^2- and SO4^2- electrodes were utilized to demonstrate that the chemical sensor was accurate and stable outside the laboratory. In the second experiment, the chemical sensor was integrated with pH, Eh, CO3^2- and H2S electrodes, and was used in 29 scans of the seabed along the Southwest Indian Ridge (SWIR) to detect hydrothermal vents, from which 27 sets of valid data were obtained. Hydrothermal vents were identified by analyzing the chemical anomalies, the primary judging criteria were decreasing voltages of Eh and H2S, matched by increasing voltages of pH and CO3^2- . We proposed that simultaneous detection of changes in these parameters will indicate a hydrothermal vent. Amongst the 27 valid sets of data, five potential hydrothermal vents were targeted using the proposed method. We suggest that our sensors could be widely employed by marine scientists.