Generation of structured light beams with polarization variation along arbitrary spatial trajectories using tri-layer metasurfaces

Conventionally,the spatially structured light beams produced by metasurfaces primarily highlight the polarization modulation of the beams propagating along the optical axis or the beams'spatial transmission trajectory.In particular,along the optical axis,the polarization state is either constant or varies continuously in each output plane.Here,we develop innovative spatially structured light beams with continually changing polarization along any arbitrary spatial transmission trajectories.With tri-layer metallic metasurfaces,the geometric characteristics of each layer structure can be adjusted to modulate the phase and polarization state of the incident terahertz(THz)wave.The beam will converge to the predefined trajectory along several paths to generate a Bessel-like beam with longitudinal polarization changes.We demonstrate the versatility of the approach by designing two THz-band structured light beams with varying polarization states along the spatial helical transmission trajectory.Continuous linear polarization changes and linear polarization to right circular polarization(RCP)and back to linear polarization changes are realized respectively.The experimental results are basically consistent with the simulated results.Our proposal for arbitrary trajectory structured light beams with longitudinally varying polarization offers a practical method for continuously regulating the characteristics of spatial structured light beams with non-axial transmission.This technique has potential uses in optical encryption,particle manipulation,and biomedical imaging.

A bio-inspired spider-like structure isolator for low-frequency vibration

This paper proposes a quasi-zero stiffness(QZS)isolator composed of a curved beam(as spider foot)and a linear spring(as spider muscle)inspired by the precise capturing ability of spiders in vibrating environments.The curved beam is simplified as an inclined horizontal spring,and a static analysis is carried out to explore the effects of different structural parameters on the stiffness performance of the QZS isolator.The finite element simulation analysis verifies that the QZS isolator can significantly reduce the first-order natural frequency under the load in the QZS region.The harmonic balance method(HBM)is used to explore the effects of the excitation amplitude,damping ratio,and stiffness coefficient on the system’s amplitude-frequency response and transmissibility performance,and the accuracy of the analytical results is verified by the fourth-order Runge-Kutta integral method(RK-4).The experimental data of the QZS isolator prototype are fitted to a ninth-degree polynomial,and the RK-4 can theoretically predict the experimental results.The experimental results show that the QZS isolator has a lower initial isolation frequency and a wider isolation frequency bandwidth than the equivalent linear isolator.The frequency sweep test of prototypes with different harmonic excitation amplitudes shows that the initial isolation frequency of the QZS isolator is 3 Hz,and it can isolate 90%of the excitation signal at 7 Hz.The proposed biomimetic spider-like QZS isolator has high application prospects and can provide a reference for optimizing low-frequency or ultra-low-frequency isolators.

Novel Even Beam Splitters Based on Subwavelength Binary Simple Periodic Rectangular Structure

In this paper, a novel method of a subwavelength binary simple periodic rectangular structure is presented to realize even beam splitting by combining the rigorous couple-wave analysis with the genetic algorithm. Several even splitters in the terahertz region were designed and one of the silicon-based beam splitters designed to separate one incident beam into four emergent beams has total efficiency up to 92.23 %. Zero-order diffraction efficiency was reduced to less than 0.192 % and the error of uniformity decreased to 6.51 9 10-6. These results break the limitation of even beam splitting based on the traditional scalar theory. In addition, the effects of the incident angle, wavelength, as well as the polarizing angle on the diffraction efficiency and uniformity were also investigated.

Stability influence factors analysis and construction of a deep beam anchorage structure in roadway roof

Deep beam anchorage structures based on spatial distribution analysis of the cable prestressed field have been proposed for roadway roof support, Stability and other factors that influence deep beam structures are studied in this paper using mechanical calculations, numerical analysis and field measurements, A mechanical model of deep beam structure subjected to multiple loading is established, including analysis of roof support in the return airway of S1203 working face in the Yuwu coal mine, China, The expression of maximum shear stress in the deep beam structure is deduced according to the stress superposition criterion, It is found that the primary factors affecting deep beam structure stability are deep beam thickness, cable pre-tension and cable spacing, The variation of maximum shear stress distribution and prestressed field diffusion effects according to various factors are analyzed using Matlah and FLAC3DTM software, and practical support parameters of the S1203 return airway roof are determined, According to the observations of rock pressure, there is no evidence of roof separation, and the maximum values of roof subsidence and convergence of wall rock are 72 and 48 mm, respectively, The results show that the proposed roof support design with a deep beam structure is feasible and achieves effective control of the roadway roof,

STRUCTURE DESIGN OF THE BEIJING SPECTROMETERⅢBEAM PIPE

The Beijing spectrometer Ⅲ （BESⅢ） beam pipe is in the center of the BESⅢ, which is the detector of the upgrade project of Beijing electron and positron collider （BEPC Ⅱ）. Electrons and positrons collide in the BESⅢ beam pipe. According to the demands of the BEPC Ⅱ, a key program of Chinese Academy of Sciences, the BESⅢ beam pipe is designed based on the finite elements analysis. The BESIII beam pipe is installed in the inner cylinder of the BESⅢ drift chamber. As a vacuum tube, the BESIII beam pipe is designed as 1 000 mm in length, 63 mm in inner diameter and 114 mm in outer diameter, respectively. The BESIII beam pipe consists of a central beryllium pipe cooled by EDM-1, the oil No.1 for electric discharge machining, and two extended copper pipes cooled by deionized water （DW）. The three parts are jointed by vacuum welding. Factors taken into account in the design are as follows. ① The wall thickness of the central beryllium pipe should be designed as small as possible to reduce the multi-scattering and improve the particle momentum resolution. And the wall thickness of the extended copper pipe should be designed as large as possible to protect the detectors from the backgrounds. ②The BESⅢ beam pipe must be sufficiently cooled to avoid the damage and prevents its influence to the BESⅢ drift chamber （DC） operation. The inner surface temperature of the DC inner cylinder must be maintained at 293±2 K. ③ The magnetic permeability of the materials used in the BESⅢ beam pipe must be less than 1.05 H/m to avoid large magnetic field distortions. ④ The static pressure of the vacuum chamber of the BESⅢ beam pipe must be less than 800 μPa. The simulating results show that the designed structure of the BESⅢ beam pipe satisfies the requirements mentioned above. The structure design scheme is evaluated and adonted hv the headouarters of BEPCⅡ.

Discrete Element with Flexible Connector for Dynamic Analysis of 3-D Beam Structures

Combined multi-body dynamics with structural dynamics, a new discrete element with flexible connector, which is applicable for 3-D beam structures, is developed in this paper. Both the generalized elastic coefficient matrix of the flexible connector and the mass matrix of discrete element may be off-diagonal in a general case. The zero-length rigid element is introduced to simulate the node at which multiple elements are jointed together. It may also be effective when the axes of adjacent elements are not in the same line. The examples for eigenvalue calculation show that the model is successful. It can be extended to the geometric nonlinear response analysis.

Effect of cooling rate on the microstructure of electron beam welded joints of two-phase TiAl-based alloy

The analysis of the microstructural characterization and phase composition of electron beam welded joint zones of Ti- 43Al-9V-O. 3Y alloy has been done in this study. The welded seam is mainly composed of B2 phase, the partial γ ＋ α2 twophase lamellar structure and granular γm phase. And the lanthanon Y existed as YAl2 phase and served as grain refined. The impact of different cooling rates on joint microstructure, fracture characteristic and tensile strength were investigated. The high cooling rate restrained the structural transformation and resulted in the ordering structure. The fracture of the joint was brittle cleavage fracture because the ordering structure went against restraining the crack propagation. With the decrease of cooling rate, the transformation amounts of lamellar structure increased, and the fracture presented the layered and crosslayered characteristic.

Equivalent continuum modeling of beam-like truss structures with flexible joints

The paper investigated the equivalent continuum modeling of beam-like repetitive truss structures considering the flexibility of joints,which models the contact between the truss member and joint by spring-damper with six directional stiffnesses and dampings.Firstly,a two-node hybrid joint-beam element was derived for modeling the truss member with flexible end joints,and a condensed model for the repeating element with flexible joints was obtained.Then,the energy equivalence method was adopted to equivalently model the truss structure with flexible joints and material damping as a spatial viscoelastic anisotropic beam model.Afterwards,the equations of motion for the equivalent beam model were derived and solved analytically in the frequency domain.In the numerical studies,the correctness of the presented method was verified by comparisons of the natural frequencies and frequency responses evaluated by the equivalent beam model with the results of the finite element method model.

Method of reverberation ray matrix for static analysis of planar framed structures composed of anisotropic Timoshenko beam members

Based on the method of reverberation ray matrix（MRRM）, a reverberation matrix for planar framed structures composed of anisotropic Timoshenko（T） beam members containing completely hinged joints is developed for static analysis of such structures.In the MRRM for dynamic analysis, amplitudes of arriving and departing waves for joints are chosen as unknown quantities. However, for the present case of static analysis, displacements and rotational angles at the ends of each beam member are directly considered as unknown quantities. The expressions for stiffness matrices for anisotropic beam members are developed. A corresponding reverberation matrix is derived analytically for exact and unified determination on the displacements and internal forces at both ends of each member and arbitrary cross sectional locations in the structure. Numerical examples are given and compared with the finite element method（FEM） results to validate the present model. The characteristic parameter analysis is performed to demonstrate accuracy of the present model with the T beam theory in contrast with errors in the usual model based on the Euler-Bernoulli（EB） beam theory. The resulting reverberation matrix can be used for exact calculation of anisotropic framed structures as well as for parameter analysis of geometrical and material properties of the framed structures.

Generation of structure light in probe absorption spectrum via microwave-driven Y-type atomic system

Behavior of structure light is investigated by monitoring probe absorption using a microwave-driven Y-type atomic media configuration.The system under consideration is driven by one of the control vortex beams as well as an extra non-vortex control beam to ensure electromagnetically induced transparency.The significant aspect in the generation of structured light is the azimuthal phase-dependent modification for probe absorption.Further intensity distribution for absorption spectra is examined for simultaneously evaluating both the control vortex beams.We also go through the radial distribution of intensity for various orbital angular momentum values.Different modes of structural beams may be distinguished using the suggested approach.Our research gives us a way for rapidly transferring vortex wavefronts from control field to probe absorption profile.This could be useful in quantum information processing.

Pseudo-beam method for compressive buckling characteristics analysis of space inflatable load-carrying structures

This paper extends Le van＇s work to the case of nonlinear problem and the complicated configuration. The wrinkling stress distribution and the pressure effects are also included in our analysis. Pseudo-beam method is presented based on the inflatable beam theory to model the inflatable structures as a set of inflatable beam elements with a prestressed state. In this method, the discretized nonlinear equations are given based upon the virtual work principle with a 3-node Timoshenko＇s beam model. Finite element simulation is performed by using a 3-node BEAM189 element incorporating ANSYS nonlinear program. The pressure effect is equivalent included in our method by modifying beam element cross-section parameters related to pressure. A benchmark example, the bending case of an inflatable cantilever beam, is performed to verify the accuracy of our proposed method. The comparisons reveal that the numerical results obtained with our method are close to open published analytical and membrane finite element results. The method is then used to evaluate the whole buckling and the loadcarrying characteristics of an inflatable support frame subjected to a compression force. The wrinkling stress and region characteristics are also shown in the end. This method gives better convergence characteristics, and requires much less computation time. It is very effective to deal with the whole load-carrying ability analytical problems for large scale inflatable structures with complex configuration.

Conversion between solid and beam element solutions of finite element method based on meta-modeling theory:development and application to a ramp tunnel structure

In this study, a new method for conversion of solid finite element solution to beam finite element solution is developed based on the meta-modeling theory which constructs a model consistent with continuum mechanics. The proposed method is rigorous and efficient compared to a typical conversion method which merely computes surface integration of solid element nodal stresses to obtain cross-sectional forces. The meta-modeling theory ensures the rigorousness of proposed method by defining a proper distance between beam element and solid element solutions in a function space of continuum mechanics. Results of numerical verification test that is conducted with a simple cantilever beam are used to find the proper distance function for this conversion. Time history analysis of the main tunnel structure of a real ramp tunnel is considered as a numerical example for the proposed conversion method. It is shown that cross-sectional forces are readily computed for solid element solution of the main tunnel structure when it is converted to a beam element solution using the proposed method. Further, envelopes of resultant forces which are of primary importance for the purpose of design, are developed for a given ground motion at the end.

Monitoring of Real-Time Complex Deformed Shapes of Thin-Walled Channel Beam Structures Subject to the Coupling Between Bi-Axial Bending and Warping Torsion

Structural health monitoring(SHM)is a research focus involving a large category of techniques performing in-situ identification of structural damage,stress,external loads,vibration signatures,etc.Among various SHM techniques,those able to monitoring structural deformed shapes are considered as an important category.A novel method of deformed shape reconstruction for thinwalled beam structures was recently proposed by Xu et al.[1],which is capable of decoupling complex beam deformations subject to the combination of different loading cases,including tension/compression,bending and warping torsion,and also able to reconstruct the full-field displacement distributions.However,this method was demonstrated only under a relatively simple loading coupling cases,involving uni-axial bending and warping torsion.The effectiveness of the method under more complex loading cases needs to be thoroughly investigated.In this study,more complex deformations under the coupling between bi-axial bending and warping torsion was decoupled using the method.The set of equations for deformation decoupling was established,and the reconstruction algorithm for bending and torsion deformation were utilized.The effectiveness and accuracy of the method was examined using a thin-walled channel beam,relying on analysis results of finite element analysis(FEA).In the analysis,the influence of the positions of the measurement of surface strain distributions on the reconstruction accuracy was discussed.Moreover,different levels of measurement noise were added to the axial strain values based on numerical method,and the noise resistance ability of the deformation reconstruction method was investigated systematically.According to the FEA results,the effectiveness and precision of the method in complex deformation decoupling and reconstruction were demonstrated.Moreover,the immunity of the method to measurement noise was proven to be considerably strong.

Short beam shear properties and failure modes of the wood-based X-type lattice sandwich structure

A wood-based X-type lattice sandwich structure was manufactured by insertion-glue method.The birch was used as core,and Oriented Strand Board was used as panel of the sandwich structure.The short beam shear properties and the failure modes of the wood-based X-type lattice sandwich structure with different core direction(vertical and parallel),unit specification(120 mm×60 mm and 60 mm×60 mm),core size(50 mm and 60 mm),and drilling depth(9 mm and 12 mm)were investigated by a short beam shear test and the establishment of a theoretical model to study the equivalent shear modulus and deflection response of the X-type lattice sandwich structure.Results from the short beam shear test and the theoretical model showed that the failure modes of the wood-based X-type lattice sandwich structure were mainly the wrinkling and crushing of the panels under three-point bending load.The experimental values of deflection response of various type specimens were higher than the theoretical values of them.For the core direction of parallel,the smaller the unit specification is,the shorter the core size is,and the deeper the drilling depth is,the greater the short beam shear properties of the wood-based X-type lattice sandwich structure is.

Broadband acoustic focusing by symmetric Airy beams with phased arrays comprised of different numbers of cavity structures

We realize broadband acoustic focusing effect by employing two symmetric Airy beams generated from phased arrays,in which the units of the phased arrays consist of different numbers of cavity structures, each of which is composed of a square cavity and two inclined channels in air. The exotic phenomenon arises from the energy overlapping of the two symmetric Airy beams. Besides, we demonstrate the focusing performance with high self-healing property, and discuss the effects of structure parameters on focusing performance, and present the characteristics of the cavity structure with straight channels. Compared with other acoustic lenses, the proposed acoustic lens has advantages of broad bandwidth（about 1.4 kHz）, high self-healing property of focusing performance, and free adjustment of focal length. Our finding should have great potential applications in ultrasound imaging and medical diagnosis.

Analytical and experimental studies on nonlinear characteristics of an L-shape beam structure

This paper focuses on theoretical and experimental investigations of planar nonlinear vibrations and chaotic dynamics of an L-shape beam structure subjected to fundamental harmonic excitation,which is composed of two beams with right-angled L-shape.The ordinary differential governing equation of motion for the L-shape beam structure with two-degree-of-freedom is firstly derived by applying the substructure synthesis method and the Lagrangian equation.Then,the method of multiple scales is utilized to obtain a four-dimensional averaged equation of the L-shape beam structure.Numerical simulations,based on the mathematical model,are presented to analyze the nonlinear responses and chaotic dynamics of the L-shape beam structure.The bifurcation diagram,phase portrait,amplitude spectrum and Poincare map are plotted to illustrate the periodic and chaotic motions of the L-shape beam structure.The existence of the Shilnikov type multi-pulse chaotic motion is also observed from the numerical results.Furthermore, experimental investigations of the L-shape beam structure are performed,and there is a qualitative agreement between the numerical and experimental results.It is also shown that out-of-plane motion may appear intuitively.

New Factor to Characterize Mechanism of “Strong Column-Weak Beam” of RC Frame Structures

Most reinforced concrete(RC)frame structures did not achieve the "strong column-weak beam" failure mode in recent big earthquakes, resulting in a large number of casualties and significant property loss. To deal with this serious problem, a new column-beam relative factor was proposed to characterize the relative yield situation of column ends and beam ends. By limiting the column-beam relative factor, RC frame structures could achieve the "strong column-weak beam" failure mode under the excitation of strong ground motions. The limit values of column-beam relative factor were calculated, analyzed and verified by using structural simulation models for corner columns in the bottom story of structures, which are destroyed most seriously in earthquakes. The results show that the limit values should be analyzed under bi-directional ground motion and with different axial compression ratios of columns. The peak ground acceleration(PGA)of ground motions has no significant effect on the limit values, while the type of strong ground motions has a significant effect on the limit values.

Effects of edge beams on mechanic behavior under lateral load in reinforced concrete hollow slab-column structure

In order to get the formulae for calculating the equivalent frame width coefficient of reinforced concrete hollow slab-column structures with edge beam,the finite element structural program was used in the elastic analysis of reinforced concrete hollow slab-column structure with different dimensions to study internal relationship between effective beam width and the frame dimensions.In addition,the formulas for calculating the increasing coefficient of edge beam were also obtained.

Finite Element Model Updating of Complicated Beam-Type Structures Based on Reduced Super Beam Model

A finite element model updating technique for complicated beam-type structures is presented in this study.Firstly, a complicated beam-type structure is reduced to a reduced super beam model with a much smaller degree of freedom by using the reduced super beam method, which is based on the classic plane cross-section assumption and displacement interpolation function of beam theory.Then based on the reduced super beam, the analysis of eigensolutions and eigensensitivities from the reduced eigenequation are processed for model updating, which will greatly reduce the computational effort when compared to the traditional model updating methods performed on the global model.Optimization techniques are adopted for updating the difference of modal dynamic properties, resulting in optimal values of the structural parameters.Finally, a complicated stiffened cylindrical shell model and a practical missile structure, served as the illustrative examples, are employed for model updating application, which demonstrate that the reduced super beam-based method is both effective and highly efficient.

A New Non-uniform Beam Element and Its Application to Buckling Analysis for Framed Structures

The non-uniform beam components are commonly used in engineering,while the method to analyze such component is not too satisfactory yet. A new non-uniform beam element with high precision was developed based on the non-linear analysis and the static condensation. Based on the interpolation theory, the displacement fields of the three-node non-uniform Euler-Bernoulli beam element were constructed at first: the quintic Hermite interpolation polynomial was used for the lateral displacement field and the quadratic Lagrange interpolation polynomial for the axial displacement field. Then,based on the basic assumptions of non-uniform Euler-Bernoulli beam whose section properties were continuously varying along its centroidal axis, the linear and geometric stiffness matrices of the three-node non-uniform beam element were derived according to the nonlinear finite element theory. Finally,the degrees of freedom ( DOFs) of the middle node of the element were eliminated using the static condensation method, and a new two-node non-uniform beam element including axial-force effect was obtained. The results indicate that each bar needs to be meshed with only one element could get a fairly accurate solution when it is applied to the stability analyses.