Sealing capacity evaluation of underground gas storage under intricate geological conditions

Evaluating underground gas storage(UGS)sealing capacity is essential for its safe construction and operational efficiency.This involves evaluating both the static sealing capacity of traps during hydrocarbon accumulation and the dynamic sealing capacity of UGS under intensive gas injection and withdrawal,and alternating loads.This study detailed the methodology developed by Sinopec.The approach merges disciplines like geology,geomechanics,and hydrodynamics,employing both dynamic-static and qualitative-quantitative analyses.Sinopec's evaluation methods,grounded in the in situ stress analysis,include mechanistic studies,laboratory tests,geological surveys,stress analysis,and fluid-solid interactions.Through tests on the static and dynamic sealing capacity of UGS,alongside investigations into sealing mechanisms and the geological and geomechanical properties of cap rocks and faults,A geomechanics-rock damage-seepage mechanics dynamic coupling analysis method has been developed to predict in situ stress variations relative to pore pressure changes during UGS operations and evaluate fault sealing capacity and cap rock integrity,thereby setting the maximum operational pressures.Utilizing this evaluation technique,Sinopec has defined performance metrics and criteria for evaluating the sealing capacity of depleted gas reservoirs,enabling preliminary sealing capacity evaluations at UGS sites.These evaluations have significantly informed the design of UGS construction schemes and the evaluation of fault sealing capacity and cap rock integrity during UGS operations.

Interfacial friction effects on sealing performances of elastomer packer

Elastomer sealing performance is of critical importance for downhole tools application including the use of fracturing(Frac)plugs during multi-stage hydraulic fracking.In practice sealing performances of such plugs are normally evaluated through pressure tests,and in numerical simulation studies,maximum contact stress,average contact stress and contact length data are used to determine sealing quality between a packer and casing.In previous studies,the impact of friction forces on sealing performance is often overlooked.This work aims to fill this knowledge gap in determining the influence of friction forces on elastomer packer sealing performances.We first determined the most appropriate constitutive hyperelastic model for the elastomers used in frac plug.Then we compared analytical calculation results with Finite Element Analysis simulation using a simplified tubular geometry and showed the significant influences on interfacial friction on elastomer packer stress distribution,deformation,and contact stress after setting.With the demonstration of validity of FEA method,we conducted systematic numerical simulation studies to show how the interfacial friction coefficients can affect the maximum contact stress,average contact stress,contact stress distribution,and maximum mises stress for an actual packer used in plug products.In addition,we also demonstrated how the groove in a packer can affect packer deformation and evolvement during setting with the consideration of interfacial stress.This study underscores the critical role that friction forces play in Frac plug performance and provides a new dimension for optimizing packer design by controlling interfacial interactions at the packer contact surfaces.

A Multi-Stage Differential-Multifactorial Evolutionary Algorithm for Ingredient Optimization in the Copper Industry

Ingredient optimization plays a pivotal role in the copper industry,for which it is closely related to the concentrate utilization rate,stability of furnace conditions,and the quality of copper production.To acquire a practical ingredient plan,which should exhibit long duration time with sufficient utilization and feeding stability for real applications,an ingredient plan optimization model is proposed in this study to effectively guarantee continuous production and stable furnace conditions.To address the complex challenges posed by this integer programming model,including multiple coupling feeding stages,intricate constraints,and significant non-linearity,a multi-stage differential-multifactorial evolution algorithm is developed.In the proposed algorithm,the differential evolutionary(DE)algorithm is improved in three aspects to efficiently tackle challenges when optimizing the proposed model.First,unlike traditional time-consuming serial approaches,the multifactorial evolutionary algorithm is utilized to optimize multiple complex models contained in the population of evolutionary algorithm caused by the feeding stability in a parallel manner.Second,a repair algorithm is employed to adjust infeasible ingredient lists in a timely manner.In addition,a local search strategy taking feedback from the current optima and considering the different positions of global optimum is developed to avoiding premature convergence of the differential evolutionary algorithm.Finally,the simulation experiments considering different planning horizons using real data from the copper industry in China are conducted,which demonstrates the superiority of the proposed method on feeding duration and stability compared with other commonly deployed approaches.It is practically helpful for reducing material cost as well as increasing production profit for the copper industry.

Multi-Stage Multidisciplinary Design Optimization Method for Enhancing Complete Artillery Internal Ballistic Firing Performance

To enhance the comprehensive performance of artillery internal ballistics—encompassing power,accuracy,and service life—this study proposed a multi-stage multidisciplinary design optimization(MS-MDO)method.First,the comprehensive artillery internal ballistic dynamics(AIBD)model,based on propellant combustion,rotation band engraving,projectile axial motion,and rifling wear models,was established and validated.This model was systematically decomposed into subsystems from a system engineering perspective.The study then detailed the MS-MDO methodology,which included Stage I(MDO stage)employing an improved collaborative optimization method for consistent design variables,and Stage II(Performance Optimization)focusing on the independent optimization of local design variables and performance metrics.The methodology was applied to the AIBD problem.Results demonstrated that the MS-MDO method in Stage I effectively reduced iteration and evaluation counts,thereby accelerating system-level convergence.Meanwhile,Stage II optimization markedly enhanced overall performance.These comprehensive evaluation results affirmed the effectiveness of the MS-MDO method.

Evolution and Application of Sealing Ability of Gypsum Caprocks under Temperature-Pressure Coupling:An Example of the ZS5 Well in the Tazhong Area of the Tarim Basin

Gypsum caprocks'sealing ability is affected by temperature-pressure coupling.Due to the limitations of experimental conditions,there is still a lack of triaxial stress-strain experiments that simultaneously consider changes in temperature and pressure conditions,which limits the accuracy of the comprehensive evaluation of the brittle plastic evolution and sealing ability of gypsum rocks using temperature pressure coupling.Triaxial stress-strain tests were utilized to investigate the differences in the evolution of the confinement capacity of gypsum rocks under coupled temperaturepressure action and isothermal-variable pressure action on the basis of sample feasibility analysis.According to research,the gypsum rock's peak and residual strengths decrease under simultaneous increases in temperature and pressure over isothermal pressurization experimental conditions,and it becomes more ductile.This reduces the amount of time it takes for the rock to transition from brittle to plastic.When temperature is taken into account,both the brittle–plastic transformation's depth limit and the lithological transformation of gypsum rocks become shallower,and the evolution of gypsum rocks under variable temperature and pressure conditions is more complicated than that under isothermal pressurization.The sealing ability under the temperature-pressure coupling is more in line with the actual geological context when the application results of the Well#ZS5 are compared.This provides a theoretical basis for precisely determining the process of hydrocarbon accumulation and explains why the early hydrocarbon were not well preserved.

Fracture sealing performance of granular lost circulation materials at elevated temperature:A theoretical and coupled CFD-DEM simulation study

Lost circulation is a common downhole problem of drilling in geothermal and high-temperature,high-pressure(HTHP)formations.Lost circulation material(LCM)is a regular preventive and remedial measure for lost circulation.However,conventional LCMs seem ineffective in high-temperature formations.This may be due to the changes in the mechanical properties of LCMs and their sealing performance under high-temperature conditions.To understand how high temperature affects the fracture sealing performance of LCMs,we developed a coupled computational fluid dynamics-discrete element method(CFD-DEM)model to simulate the behavior of granular LCMs in fractures.We summarized the literature on the effects of high temperature on the mechanical properties of LCMs and the rheological properties of drilling fluid.We conducted sensitivity analyses to investigate how changing LCM slurry properties affected the fracture sealing efficiency at increasing temperatures.The results show that high temperature reduces the size,strength,and friction coefficient of LCMs as well as the drilling fluid viscosity.Smaller,softer,and less frictional LCM particles have lower bridging probability and slower bridging initiation.Smaller particles tend to form dual-particle bridges rather than single-particle bridges.These result in a deeper,tighter,but unstable sealing zone.Reduced drilling fluid viscosity leads to faster and shallower sealing zones.

Dynamic evaluation on sealing capacity of caprocks of the Meso-Neoproterozoic reservoirs in Ordos Basin,China

The Meso-Neoproterozoic is a new play in the Ordos Basin.A deeper understanding about the dynamic relationship between the caprocks and the source rocks is needed.Based on the comprehensive analysis of hydrocarbon source development characteristics of the Meso-Neoproterozoic and its overlying strata,as well as the formation contact relationships,lithology characteristics and exploratory drilling data,it is recognized that the Meso-Neoproterozoic contains two types of petroleum accumulation assemblage,that is,the“self-sourced indigenous”and“upper source rock-lower reservoir”assemblages.The former is mainly controlled by the development and distribution of source rocks of the Changcheng System,with the Lower Cambrian shale sequence as its caprock.The later is controlled by the superposition between the Meso-Neoproterozoic and its overlying source rocks and this assemblage is mainly distributed in Hangjinqi and Pingliang areas with the Carboniferous-Permian shale sequence as its caprock.The dynamic evaluation on the displacement pressure serves to reconstruct the displacement pressure history of the caprock.The results show that the shale sequence of the Cambrian Maozhuang Formation in well XY 1 in the southern Ordos Basin has possibly acquired the ability of sealing natural gas since the early of Late Triassic.Its displacement pressure increased rapidly up to 20 MPa during the Late Triassic-Jurassic and keeps at 9.2 MPa at present,indicating fair sealing ability.The Carboniferous-Permian caprocks in Hangjinqi area could have acquired the ability to seal natural gas in the Late Jurassic-Early Cretaceous,and the present-day displacement pressure is 9e12 MPa,indicating good sealing ability.The upper Paleozoic caprock in Pingliang area has been able to seal natural gas since the Early Jurassic,with a maximum displacement pressure of 23 MPa during the Cretaceous period and a current value of 17 e20 MPa,indicative of strong ability to seal natural gas.The sealing ability of caprocks of both the“selfsourced indigenous”and“upper source rock-lower reservoir”assemblages has come into being earlier than or at least no later than the peak gas generation of the source rocks and therefore the caprocks are dynamically effective in geohistory.The Meso-Neoproterozoic reservoirs in the Ordos Basin are well preserved and probabally of better potential for exploration in terms of the caprock-source rock combination.

Research on Regulation Method of Energy Storage System Based on Multi-Stage Robust Optimization

To address the scheduling problem involving energy storage systems and uncertain energy,we propose a method based on multi-stage robust optimization.This approach aims to regulate the energy storage system by using a multi-stage robust optimal control method,which helps overcome the limitations of traditional methods in terms of time scale.The goal is to effectively utilize the energy storage power station system to address issues caused by unpredictable variations in environmental energy and fluctuating load throughout the day.To achieve this,a mathematical model is constructed to represent uncertain energy sources such as photovoltaic and wind power.The generalized Benders Decomposition method is then employed to solve the multi-stage objective optimization problem.By decomposing the problem into a series of sub-objectives,the system scale is effectively reduced,and the algorithm’s convergence ability is improved.Compared with other algorithms,the multi-stage robust optimization model has better economy and convergence ability and can be used to guide the power dispatching of uncertain energy and energy storage systems.

Evaluation of the dynamic sealing performance of cap rocks of underground gas storage under multi-cycle alternating loads

The static sealing of underground gas storage(UGS),including the integrity of cap rocks and the stability of faults,is analyzed from a macro perspective using a comprehensive geological evaluation method.Changes in pore structure,permeability,and mechanical strength of cap rocks under cyclic loads may impact the rock sealing integrity during the injection and recovery phases of UGS.In this work,the mechanical deformation and failure tests of rocks,as well as rock damage tests under alternating loads,are conducted to analyze the changes in the strength and permeability of rocks under multiple-cycle intense injection and recovery of UGS.Additionally,this study proposes an evaluation method for the dynamic sealing performance of UGS cap rocks under multi-cycle alternating loads.The findings suggest that the failure strength(70%)can be used as the critical value for rock failure,thus providing theoretical support for determining the upper limit of operating pressure and the number of injection-recovery cycles for the safe operation of a UGS system.

Study on Sealing Characteristics of Sliding Seal Assembly of Aircraft Hydraulic Actuator

The hydraulic actuator,known as the"muscle"of military aircraft,is responsible for flight attitude adjustment,trajectory control,braking turn,landing gear retracting and other actions,which directly affect its flight efficiency and safety.However,the sealing assembly often has the situation of over-aberrant aperture fit clearance or critical over-aberrant clearance,which increases the failure probability and degree of movable seal failure,and directly affects the flight efficiency and safety of military aircraft.In this paper,the simulation model of hydraulic actuator seal combination is established by ANSYS software,and the sealing principle is described.The change curve of contact width and contact pressure of combination seal under the action of high-pressure fluid is drawn.The effects of different oil pressure,fit clearance and other parameters on the sealing performance are analyzed.Finally,the accelerated life test of sliding seal components is carried out on the hydraulic actuator accelerated life test rig,and the surface morphology is compared and analyzed.The research shows that the O-ring is the main sealing element and the role of the check ring is to protect and support the O-ring to prevent damage caused by squeezing into the fit clearance,so the check ring bears a large load and is prone to shear failure.Excessive fit clearance is the main factor affecting the damage of the check ring,and the damage parts are mainly concentrated at the edge of the sealing surface.This paper provides a theoretical basis for the design of hydraulic actuator and the improvement of sealing performance.

深水采油树Spring-Seal密封圈接触模型构建与实验测试

为提高深水采油树在高压、高温、低温等工况下长时间工作的稳定性,对采油树密封圈进行重新设计,提出Spring-Seal密封圈(以下简称S密封圈);基于赫兹接触理论、填料密封接触理论,重新构建S密封圈接触力学模型;建立有限元仿真分析模型,分析不同条件下S密封圈的密封性能,同时验证新建接触模型的合理性;利用实验测试S密封圈的实际密封效果。研究结果表明:S密封圈在高压、高温、低温等工况下能够长时间稳定工作且密封性能良好。研究结果可为S密封圈的接触研究及工程运用提供理论参考。

Air tightness of compressed air storage energy caverns with polymer sealing layer subjected to various air pressures

During the operation of compressed air storage energy system,the rapid change of air pressure in a cavern will cause drastic changes in air density and permeability coefficient of sealing layer.To calculate and properly evaluate air tightness of polymer sealing caverns,the air-pressure-related air density and permeability must be considered.In this context,the high-pressure air penetration in the polymer sealing layer is studied in consideration of thermodynamic change of the cavern structure during the system operation.The air tightness model of compressed air storage energy caverns is then established.In the model,the permeability coefficient and air density of sealing layer vary with air pressure,and the effectiveness of the model is verified by field data in two test caverns.Finally,a compressed air storage energy cavern is taken as an example to understand the air tightness.The air leakage rate in the caverns is larger than that using air-pressure-independent permeability coefficient and air density,which is constant and small in the previous leakage rate calculation.Under the operating pressure of 4.5-10 MPa,the daily air leakage in the compressed air storage energy cavern of Yungang Mine with high polymer butyl rubber as the sealing material is 0.62%,which can meet the sealing requirements of compressed air storage energy caverns.The air tightness of the polymer sealing cavern is mainly affected by the cavern operating pressure,injected air temperature,cavern radius,and sealing layer thickness.The cavern air leakage rate will be decreased to reduce the cavern operating pressure the injection air temperature,or the cavern radius and sealing layer thickness will be increased.

Trace Elements of Multi-stage Minerals and Titanite U-Pb Dating for the Gneisses from Liansan Island,Sulu UHPM Belt

Gneisses with anatectic characteristics from the Liansan island in the Sulu UHPM(ultra-high pressure metamorphic)belt were studied for petrography,titanite U-Pb dating and mineral geochemistry.Three origins of garnets are distinguished:metamorphic garnet,peritectic garnet and anatectic garnet,which are formed in the stages of peak metamorphism,retrograde anatexis and melt crystallization,respectively.The euhedral titanite has a high content of REE and high Th/U ratios,which is interpreted as indicating that it was newly-formed from an anatectic melt.The LA-ICP-MS titanite U-Pb dating yields 214-217 Ma ages for the titanite(melt)crystallization.The distribution of trace elements varies in response to the different host minerals at different stages.At the peak metamorphic stage,Y and HREE are mainly hosted by garnet,Ba and Rb by phengite,Sr,Nb,Ta,Pb,Th,U and LREE by allanite and Y,U and HREE by zircon.During partial melting,Y,Pb,Th,U and REE are released into the melt,which causes a dramatic decline of these element contents in the retrograde minerals.Finally,titanite absorbs most of the Nb,U,LREE and HREE from the melt.Therefore,the different stages of metamorphism have different mineral assemblages,which host different trace elements.

Overview of multi-stage charging strategies for Li-ion batteries

To reduce the carbon footprint in the transportation sector and improve overall vehicle efficiency,a large number of electric vehicles are being manufactured.This is due to the fact that environmental concerns and the depletion of fossil fuels have become significant global problems.Lithium-ion batteries(LIBs)have been distinguished themselves from alternative energy storage technologies for electric vehicles(EVs) due to superior qualities like high energy and power density,extended cycle life,and low maintenance cost to a competitive price.However,there are still certain challenges to be solved,like EV fast charging,longer lifetime,and reduced weight.For fast charging,the multi-stage constant current(MSCC) charging technique is an emerging solution to improve charging efficiency,reduce temperature rise during charging,increase charging/discharging capacities,shorten charging time,and extend the cycle life.However,there are large variations in the implementation of the number of stages,stage transition criterion,and C-rate selection for each stage.This paper provides a review of these problems by compiling information from the literature.An overview of the impact of different design parameters(number of stages,stage transition,and C-rate) that the MSCC charging techniques have had on the LIB performance and cycle life is described in detail and analyzed.The impact of design parameters on lifetime,charging efficiency,charging and discharging capacity,charging speed,and rising temperature during charging is presented,and this review provides guidelines for designing advanced fast charging strategies and determining future research gaps.

A multiphysical-geochemical coupling model for caprock sealing efficiency in CO_(2) geosequestration

Precipitation or dissolution due to geochemical reactions has been observed in the caprocks for CO_(2) geosequestration.Geochemical reactions modify the caprock sealing efficiency with self-limiting or self-enhancement.However,the effect of this modification on the caprock sealing efficiency has not been fully investigated through multiphysical-geochemical coupling analysis.In this study,a multiphysical-geochemical coupling model was proposed to analyze caprock sealing efficiency.This coupling model considered the full couplings of caprock deformation,two-phase flow,CO_(2) concentration diffusion,geochemical reaction,and CO_(2) sorption.The two-phase flow only occurs in the fracture network and the CO_(2) may partially dissolve into water and diffuse through the concentration difference.The dissolved CO_(2) has geochemical reactions with some critical minerals,thus altering flow channels.The CO_(2) in the fracture network diffuses into matrix,causing the matrix swelling.This fully coupling model was validated with a penetration experiment on a cement cube and compared with two other models for CO_(2) storage plumes.Finally,the effects of geochemical reactions on penetration depth and pore pressure were studied through parametric study.The numerical simulations reveal that the coupling of geochemical reactions and matrix diffusion significantly affect the caprock sealing efficiency.Geochemical reactions occur at a short time after the arrival of CO_(2) concentration and modify the fracture porosity.The CO_(2) diffusion into the matrix requires a much longer time and mainly induces matrix swelling.These effects may produce selfenhancement or self-limiting depending on the flow rate in the fracture network,thus significantly modifying caprock sealing efficiency.

Multi-Stage Improvement of Marine Predators Algorithm and Its Application

The metaheuristic algorithms are widely used in solving the parameters of the optimization problem.The marine predators algorithm(MPA)is a novel population-based intelligent algorithm.Although MPA has shown a talented foraging strategy,it still needs a balance of exploration and exploitation.Therefore,a multi-stage improvement of marine predators algorithm(MSMPA)is proposed in this paper.The algorithm retains the advantage of multistage search and introduces a linear flight strategy in the middle stage to enhance the interaction between predators.Predators further away from the historical optimum are required to move,increasing the exploration capability of the algorithm.In the middle and late stages,the searchmechanism of particle swarmoptimization(PSO)is inserted,which enhances the exploitation capability of the algorithm.This means that the stochasticity is decreased,that is the optimal region where predators jumping out is effectively stifled.At the same time,self-adjusting weight is used to regulate the convergence speed of the algorithm,which can balance the exploration and exploitation capability of the algorithm.The algorithm is applied to different types of CEC2017 benchmark test functions and threemultidimensional nonlinear structure design optimization problems,compared with other recent algorithms.The results show that the convergence speed and accuracy of MSMPA are significantly better than that of the comparison algorithms.

On the installation of an in situ large-scale vertical SEALing (VSEAL) experiment on bentonite pellet-powder mixture

Recently,the Institute for Radiological protection and Nuclear Safety(IRSN)has launched VSEAL(Vertical SEALing)project to investigate the impact of gas migration on the long-term performance of bentonite based vertical sealing systems(VSS).The first VSEAL in situ test was emplaced in IRSN’s Underground Research Laboratory(URL)in Tournemire(France)in 2019 and was equipped with 76 wired and wireless sensors.The test is still in progress,but the collected set of data provides already valuable information of the hydro-mechanical behavior of VSS during hydration.The swelling core consists of a mixture of highdensity pellets and powder of MX80 bentonite in a ratio of 80/20(in dry mass).An innovative method was adopted to drill a 1-m diameter and w10-m deep shaft in order to minimize the rock perturbation at the sidewalls.Because a specific protocol was adopted to install the bentonite mixture together with a careful characterization of the core during construction,VSEAL 1 constitutes the unique in situ sealing test with a well-known initial structural distribution of the pellets and the powder.Some heterogeneities occurred within the experiment during the installation process:a damaged zone developed around the shaft walls due to the interruption of the installation operations caused by COVID19 lockdown in France;a technological gap with a variable thickness between the last pellets layer and the top confining lid and a heterogeneous distribution of the bentonite powder at some layers inducing large inter pellets voids close to the bentonite-rock interface.Artificially injected water volume,relative humidity,water content and swelling pressure in both radial and axial directions were monitored.Comparison of the results showed that the presence of installation-induced heterogeneities led to the generation of preferential flow paths that influenced the swelling pressure evolution at radial and axial directions.

Propagation and sealing efficiency of chemical grouting in a two-dimensional fracture network with flowing water

In this study, an orthogonal array experiment is conducted by using a transparent fracture network replica. Image processing and theoretical analysis are performed to investigate the model sealing efficiency(SE), factors influencing SE, and the effect of flowing water on propagation. The results show that grout propagation can be classified into three patterns in the fracture network: sealing off, partial sealing,and major erosion. The factors controlling the SE in a descending order of the amount of influence are the initial water flow speed, fracture aperture, grout take, and gel time. An optimal value for the combination of the gel time and grout take(artificial factors) can result in a good SE. The grouting and seepage pressures are measured, and the results reveal that their variations can indicate the SE to some extent. The SE is good when the seepage pressure at each point increases overall;the frequent fluctuations in the seepage pressure indicate a moderately poor SE, and an overall decline in the seepage pressure indicates a major erosion type. The deflection effect of grouting shows an approximately elliptical propagation with the long axis expanding along the wider fracture opening, demonstrating further application in grouting design.

Geopolymer-based modification of blasting sealing materials and optimization of blasting block size in coal seams of open pit mines

This research proposes the utilization of a geopolymer-based blasting sealing material to improve the profitability of coal sales and reduce the rate of coal fragmentation during blasting in open pit mines.The study first focused on optimizing the strength of the sealant material and reducing curing time.This was achieved by regulating the slag doping and sodium silicate solution modulus.The findings demonstrated that increasing slag content and improving the material resulted in an early rise in strength while increasing the modulus of the sodium silicate solution extended the curing time.The slag doping level was fixed at 80 g,and the sodium silicate solution modulus was set at 1.5.To achieve a strength of 3.12 MPa,the water/gel ratio was set at 0.5.The initial setting time was determined to be 33 min,meeting the required field test duration.Secondly,the strength requirements for field implementation were assessed by simulating the action time and force destruction process of the sealing material during blasting using ANSYS/LS-DYNA software.The results indicated that the modified material meets these requirements.Finally,the Shengli Open Pit Coal Mine served as the site for the field test.It was observed that the hole-sealing material’s hydration reaction created a laminated and flocculated gel inside it.This enhanced the density of the modified material.Additionally,the pregelatinized starch,functioning as an organic binder,filled the gaps between the gels,enhancing the cohesion and bonding coefficient of the material.Upon analyzing the post-blasting shooting effect diagram using the Split-Desktop software,it was determined that the utilization of the modified blast hole plugging material resulted in a decrease in the rate of coal fragmentation from 33.2%to 21.1%.This reduction exhibited a minimal error of 1.63%when compared to the field measurement,thereby providing further confirmation of the exceptional plugging capabilities of the modified material.This study significantly contributes to establishing a solid theoretical basis for enhancing the blasting efficiency of open pit mines and,in turn,enhancing their economic advantages.

Influence of pressure disturbance wave on dynamic response characteristics of liquid film seal for multiphase pump

Slug flow or high GVF(Gas Volume Fraction)conditions can cause pressure disturbance waves and alternating loads at the boundary of mechanical seals for multiphase pumps,endangering the safety of multiphase pump units.The mechanical seal model is simplified by using periodic boundary conditions and numerical calculations are carried out based on the Zwart-Gerber-Belamri cavitation model.UDF(User Define Function)programs such as structural dynamics equations,alternating load equations,and pressure disturbance equations are embedded in numerical calculations,and the dynamic response characteristics of mechanical seal are studied using layered dynamic mesh technology.The results show that when the pressure disturbance occurs at the inlet,as the amplitude and period of the disturbance increase,the film thickness gradually decreases.And the fundamental reason for the hysteresis of the film thickness change is that the pressure in the high-pressure area cannot be restored in a timely manner.The maximum value of leakage and the minimum value of axial velocity are independent of the disturbance period and determined by the disturbance amplitude.The mutual interference between enhanced waves does not have a significant impact on the film thickness,while the front wave in the attenuated wave has a promoting effect on the subsequent film thickness changes,and the fluctuation of the liquid film cavitation rate and axial velocity under the attenuated wave condition deviates from the initial values.Compared with pressure disturbance conditions,alternating load conditions have a more significant impact on film thickness and leakage.During actual operation,it is necessary to avoid alternating load conditions in multiphase pump mechanical seals.