Mitigation of Optical Multipath Interference Algorithms in IM-DD Transmission System

This paper aimed to propose two algorithms,DA-M and RF-M,of reducing the impact of multipath interference(MPI)on intensity modulation direct detection(IM-DD)systems,particularly for four-level pulse amplitude modulation(PAM4)systems.DA-M reduced the fluctuation by averaging the signal in blocks,RF-M estimated MPI by subtracting the decision value of the corresponding block from the mean value of a signal block,and then generated interference-reduced samples by subtracting the interference signal from the product of the corresponding MPI estimate and then weighting factor.This paper firstly proposed to separate the signal before decision-making into multiple blocks,which significantly reduced the complexity of DA-M and RF-M.Simulation results showed that the MPI noise of 28 GBaud IMDD system under the linewidths of 1e5 Hz,1e6 Hz and 10e6 Hz can be effectively alleviated.

Improving Network Availability through Optimized Multipath Routing and Incremental Deployment Strategies

Currently,distributed routing protocols are constrained by offering a single path between any pair of nodes,thereby limiting the potential throughput and overall network performance.This approach not only restricts the flow of data but also makes the network susceptible to failures in case the primary path is disrupted.In contrast,routing protocols that leverage multiple paths within the network offer a more resilient and efficient solution.Multipath routing,as a fundamental concept,surpasses the limitations of traditional shortest path first protocols.It not only redirects traffic to unused resources,effectively mitigating network congestion,but also ensures load balancing across the network.This optimization significantly improves network utilization and boosts the overall performance,making it a widely recognized efficient method for enhancing network reliability.To further strengthen network resilience against failures,we introduce a routing scheme known as Multiple Nodes with at least Two Choices(MNTC).This innovative approach aims to significantly enhance network availability by providing each node with at least two routing choices.By doing so,it not only reduces the dependency on a single path but also creates redundant paths that can be utilized in case of failures,thereby enhancing the overall resilience of the network.To ensure the optimal placement of nodes,we propose three incremental deployment algorithms.These algorithms carefully select the most suitable set of nodes for deployment,taking into account various factors such as node connectivity,traffic patterns,and network topology.By deployingMNTCon a carefully chosen set of nodes,we can significantly enhance network reliability without the need for a complete overhaul of the existing infrastructure.We have conducted extensive evaluations of MNTC in diverse topological spaces,demonstrating its effectiveness in maintaining high network availability with minimal path stretch.The results are impressive,showing that even when implemented on just 60%of nodes,our incremental deployment method significantly boosts network availability.This underscores the potential of MNTC in enhancing network resilience and performance,making it a viable solution for modern networks facing increasing demands and complexities.The algorithms OSPF,TBFH,DC and LFC perform fast rerouting based on strict conditions,while MNTC is not restricted by these conditions.In five real network topologies,the average network availability ofMNTCis improved by 14.68%,6.28%,4.76%and 2.84%,respectively,compared with OSPF,TBFH,DC and LFC.

Performance enhancement of a viscoelastic bistable energy harvester using time-delayed feedback control

This paper focuses on the stochastic analysis of a viscoelastic bistable energy harvesting system under colored noise and harmonic excitation, and adopts the time-delayed feedback control to improve its harvesting efficiency. Firstly, to obtain the dimensionless governing equation of the system, the original bistable system is approximated as a system without viscoelastic term by using the stochastic averaging method of energy envelope, and then is further decoupled to derive an equivalent system. The credibility of the proposed method is validated by contrasting the consistency between the numerical and the analytical results of the equivalent system under different noise conditions. The influence of system parameters on average output power is analyzed, and the control effect of the time-delayed feedback control on system performance is compared. The output performance of the system is improved with the occurrence of stochastic resonance(SR). Therefore, the signal-to-noise ratio expression for measuring SR is derived, and the dependence of its SR behavior on different parameters is explored.

基于Multipath QUIC协议的数据流传输与场景化研究

随着信息技术的不断发展,网民的数量也在不断攀升。传统的网络传输协议无法支持同时选择两种网络连接方式,这会导致网络传输效率低下。本文提出了利用多路径快速用户数据报网络连接(Multipath Quick UDP Internet Connections,MPQUIC)协议对此类问题进行优化的解决方式。该协议已广泛应用在图片下载场景、短视频场景、动态加速场景以及直播场景中,极大地提高了用户体验。

基于Multipath的煤矿巷道三维模型构建方法

针对现有煤矿巷道三维模型存在灵活性和可移植性差、数据更新维护困难等问题,提出了一种基于Multipath的煤矿巷道三维模型构建方法。该方法通过定义点弧拓扑数据模型,将煤矿CAD格式数据转换为Geodatabase中的要素类,利用开发的ArcGIS Engine程序、通过插入节点坐标生成巷道三维模型,实现了煤矿巷道自动建模,有效减少了巷道三维建模的工作量。

Modeling GPS multipath effect based on spherical cap harmonic analysis

Most GPS positioning errors can be eliminated or removed by the differential technique or the modeling method,but the multipath effect is a special kind of system or gross error,so it is difficult to be simulated or eliminated.In order to improve the accuracy of GPS positioning,the single-epoch pseudorange multipath effects at GPS station were calculated,and firstly modeled based on the spherical cap harmonic（SCH）,which is the function of satellite longitude and latitude with the robust method.The accuracy of the kinematic point positioning technique was improved by correcting pseudorange observations with the multipath effect calculated by the SCH model,especially in the elevation direction.The spherical cap harmonic can be used to model the pseudorange multipath effect.

Modeling of temperature-humidity for wood drying based on time-delay neural network

The temperature-humidity models of wood drying were developed based on Time-delay neural network and the identification structures of Time-delay neural network were given. The controlling model and the schedule model, which revealed the relation between controlling signal and temperature-humidity and the relation between wood moisture content and temperature-humidity of wood drying, were separately presented. The models were simulated by using the measured data of the experimental drying kiln. The numerical simulation results showed that the modeling method was feasible, and the models were effective.

Hybrid particle filtering algorithm for GPS multipath mitigation

An altemative algorithm for mitigating GPS multipath was presented by integrating unscented Kalman filter （UKF） and wavelet transform with particle filter. Within consideration of particle degeneracy, UKF was taken for drawing particle. To remove the noise from raw data and data processing error, adaptive wavelet filtering with threshold was adopted while data preprocessing and drawing particle. Three algorithms, named EKF-PF, UKF-PF and WM-UKF-PF, were performed for comparison. The proposed WM-UKF-PF algorithm gives better error minimization, and significantly improves performance of multipath mitigation in terms of SNR and coefficient even though it has computation complexity. It is of significance for high-accuracy positioning and non-stationary deformation analysis.

Multipath mitigation method for tracking Galileo signals

In order to improve the performance of multipath mitigation in tracking Galileo signals, a new multipath mitigation method named early-late strobe correlator （ELSC） is proposed. By applying the strobe correlator used widely in global positioning system （GPS） scenarios to Galileo E1 signals, it can be found that the strobe correlator has an undesirable level of performance when the delay of multipath signals is about 0. 5 chip. Combining several strobe correlators, the ELSC can effectively mitigate the multipath effect especially for the multipath signals with the 0. 5 chip delay. The multipath error envelopes between the strobe correlator and the ELSC are compared for Galileo E1 signals. The simulation results indicate that the ELSC performs excellently on multipath mitigation, and can be applied in both Galileo scenarios and GPS scenarios.

Behavioral modeling of RF power amplifiers with time-delay feed-forward neural networks

A novel behavioral model using three-layer time-delay feed-forward neural networks （TDFFNN）is adopted to model radio frequency （RF）power amplifiers exhibiting memory nonlinearities. In order to extract the parameters, the back- propagation algorithm is applied to train the proposed neural networks. The proposed model is verified by the typical odd- order-only memory polynomial model in simulation, and the performance is compared with different numbers of taped delay lines（TDLs） and perceptrons of the hidden layer. For validating the TDFFNN model by experiments, a digital test bench is set up to collect input and output data of power amplifiers at a 60 × 10^6 sample/s sampling rate. The 3.75 MHz 16-QAM signal generated in the vector signal generator（VSG） is chosen as the input signal, when measuring the dynamic AM/AM and AM/PM characteristics of power amplifiers. By comparisons and analyses, the presented model provides a good performance in convergence, accuracy and efficiency, which is approved by simulation results and experimental results in the time domain and frequency domain.

A comparison analysis of multipath extract methods in short-baseline applications of GPS

In order to eliminate the multipath errors existing in static short-baseline applications, a novel de-noising method based on a singular spectrum analysis （named as DSSA） is introduced to extract multipath signals. The multipath error is extracted from the double difference （DD） residuals by DSSA and then applied to the correct multipath error in subsequent measurements based on the correlation among adjacent epochs. Methods based on discrete wavelet transform （DWT） and stationary wavelet transform （SWT） are introduced as comparisons of DSSA based on analysis of a simulated signal. Real baseline residuals are tested to verify different extract methods. Results show that compared with the SWT, the DSSA improves the root mean square （RMS） of the residual by 48.6% and achieves a time reduction of 75.3%.

HiQoS:An SDN-Based Multipath QoS Solution

Today's Internet architecture provides only "best effort" services,thus it cannot guarantee quality of service(QoS) for applications.Software Defined Network(SDN)is a new approach to computer networking that separates control plane and forwarding planes,and has the advantage of centralized control and programmability.In this paper,we propose HiQoS that provides QoS guarantees using SDN.Moreover,HiQoS makes use of multiple paths between source and destination and queuing mechanisms to guarantee QoS for different types of traffic.Experimental results show that our HiQoS scheme can reduce delay and increase throughput to guarantee QoS.Very importantly,HiQoS recovers from link failure very quickly by rerouting traffic from failed path to other available path.

Novel adaptive Hatch filter to mitigate the effects of ionosphere and multipath on LAAS

It has been proven that carrier smoothing and differential global positioning system （DGPS） are effective to improve the accuracy of pseudorange by reducing the noise in it and eliminating almost all the common mode errors between the ground station and user. However, another issue coming with local area augmentation system （LAAS） is how to find an adaptive smoothing window width to minimize the error on account of ionosphere delay and multipath. Based on the errors analysis in carrier smoothing process, a novel algorithm is formulated to design adaptive Hatch filter whose smoothing window width flexibly varies with the characteristic of ionosphere delay and multipath in the differential carrier smoothing process. By conducting the simulation in LAAS and after compared with traditional Hatch filers, it reveals that not only the accuracy of differential correction, but also the accuracy and the robustness of positioning results are significantly improved by using the designed adaptive Hatch filter.

GPS short-delay multipath estimation and mitigation based on least square method

The GPS multipath signal model is presented, which indicates that the coherent DLL outputs in multipath environment are the convolution between the ideal DLL outputs and the channel responses. So the channel responses can be estimated by a least square method using the observed curve of the DLL discriminator. In terms of the estimated multipath channels, two multipath mitigation methods are discussed, which are equalization filtering and multipath subtracting, respectively. It is shown, by computer simulation, that the least square method has a good performance in channels estimation and the multipath errors can be mitigated almost completely by either of the methods. However, the multipath subtracting method has relative small remnant errors than equalization filtering.

Energy Entropy On-Demand Multipath Routing Protocol for Mobile Ad Hoc Networks

This paper provides a critical review of energy entropy theory in Mobile Ad Hoc Networks (MANETs) and proposes an Energy Entropy on Ad Hoc On-demand Distance Vector Multipath (EEAODVM) routing protocol. The essential idea of the protocol is to find every route which can minimize the node residual energy in the process of selecting path. It balances individual node battery energy utilization and hence prolongs the entire network lifetime. The results of simulation show that, with the proposed EEAODVM routing protocol, packet delivery ratio, routing overhead ratio, average end-to-end delay, network's lifetime and minimal residual energy ratio can be improved in most of cases. It is an available approach for multipath routing decision.

Energy Based Ultra-Wideband Multipath Routing Algorithm in Ad Hoc Sensor Networks

The Energy based Ultra-Wideband Multipath Routing(EUMR) algorithm for Ad hoc sensor network is proposed. It utilizes the function of UWB positioning to reduce the network communication delay and route overhead. Furthermore,the algorithm considers energy consumption,the residual energy and node hops of communication paths to make energy consumption more balanced and extend the network lifetime. Then routing which is stable,energy-saving and low-delay is realized. Simulation results show that the algorithm has better performance on saving energy,route overhead,stability and extending network lifetime.

Multipath Source Self Repair Routing Algorithm for Mobile Ad Hoc Networks

A multipath source self repair routing (MSSRR) algorithm for mobile ad hoc networks is proposed. By using multiple paths which can be repaired by themselves to transmit packets alternately, the network's load is balanced, the link state in the network can be checked in time, the number of the times the route discovery mechanism starts is decreased. If only one route which will be broken can be used to transmit the packets, the route discovery mechanism is restarted.The algorithm is implemented on the basis of dynamic source routing (DSR). The effect of MSSRR on lifetime of the access from the source to the destination and the overhead is discussed. Compared with the performance of DSR,it can be seen that the algorithm can improve the performance of the network obviously and the overhead almost does not increase if the average hop count is larger.

Cross-correlation function based multipath mitigation technique for cosine-BOC signals

We propose a new multipath mitigation technique based on cross-correlation function for the new cosine phased binary off-set carrier （cosine-BOC） modulated signals, which will most likely be employed in both European Galileo system and Chinese Compass system. This technique is implemented to create an optimum cross-correlation function via designing the modulated symbols of the local signal. And the structure of the code tracking loop for cosine-BOC signals is quite simple including only two real correlators. Results demonstrate that the technique efficiently eliminates the ranging errors in the medium and long multipath regions with respect to the conventional receiver correlation techniques.

PD-type iterative learning control for nonlinear time-delay system with external disturbance

The PD-type iterative learning control design of a class of affine nonlinear time-delay systems with external disturbances is considered. Sufficient conditions guaranteeing the convergence of the n-norm of the tracking error are derived. It is shown that the system outputs can be guaranteed to converge to desired trajectories in the absence of external disturbances and output measurement noises. And in the presence of state disturbances and measurement noises, the tracking error will be bounded uniformly. A numerical simulation example is presented to validate the effectiveness of the proposed scheme.

Parameter design for a vibration absorber with time-delayed feedback control

Traditional passive vibration absorbers are effective only when their natural frequencies are close to those of the excitations. To solve this problem, a vibration absorber with time-delayed feedback control is proposed to suppress vibration of the primary system under excitation with changing frequency. Firstly, the mechanical model of the delay coupled system is established. Then, the displacement transfer ratio of the system is obtained. The stability of the system is analyzed since delay may result in destabilization. Next, in order to design the control parameters, the vibration absorption performances of the proposed time-delayed vibration absorber are studied. The vibration absorption region is shown. The results show that time-delayed feedback control is able to change the response of the system. The effective vibration absorption frequency band is adjustable by tuning the control gain and time delay. The effective frequency band can be widened when choosing appropriate control parameters. The vibration absorption performances can be greatly improved by the time-delayed absorber. In addition, the optimum control parameters are obtained. Finally, the experimental prototype is constructed. Several tests with different control parameters are taken. The experimental and analytical results match quite well.