Influence of carbon sources on the performance of carbon-coated nano-silicon

Silicon-based material is an important anode material for next-generation lithium-ion batteries.In order to overcome its shortcomings,carbon coating is often employed to improve the electrochemical performance.However,the carbon source,carbon content,and different contact and mixing schemes between carbon sources and silicon are all complex factors and need to be clarified.In this study,nano-silicon is coated by the chemical vapor deposition method using different carbon sources,such as acetylene,methane,propane,and propylene.Carbon content after coating is designed to stay at the same level to reduce the experimental error.Results show the sample with higher conductivity provides higher cycle performance.Propylene is the best choice of the four carbon sources studied in this work.These results indicate that the selection of the carbon source is an important factor that plays a significant role in electrochemical performance.

Effects of carbon sources and temperature on the formation and structural characteristics of food-related Staphylococcus epidermidis biofilms

Biofilms are a constant concern in the food industry;understanding the effect of environmental conditions on biofilm formation is essential to develop effective control strategies.Therefore,this study was conducted to investigate biofilms formation by Staphylococcus epidermidis under various conditions.Biofilms were cultured in nutrient broth containing different carbon source concentrations(0–10 mg/mL)on polystyrene surfaces for 32 h of incubation at 37℃or 55℃,with quantification and enumeration at 8,16,24 and 32 h.S.epidermidis developed biofilms under all tested conditions;achieved the highest yield of biofilm biomass at 2.5 mg/mL for all carbon sources at 37℃.The highest efficiency of extracellular polymeric substance(EPS)molecule production occurred under glucose availability in the growth environment,with a higher yield of biomass and a significantly smaller number of metabolically active cells than under other tested conditions.A condensed ball-shaped structure was observed under the lactose condition.Meanwhile,biofilms in the presence of maltose showed mainly opaque thick rich colonies,while a compact multilayered-shaped structure was exhibited under both glucose and sucrose conditions.These results contribute to a better understanding of the biofilm formation by S.epidermidis in order to reduce contamination and recontamination in the food industry.

Direct Synthesis of Co-doped Graphene on Dielectric Substrates Using Solid Carbon Sources

Direct synthesis of high-quality doped graphene on dielectric substrates without transfer is highly desired for simplified device processing in electronic applications.However,graphene synthesis directly on substrates suitable for device applications,though highly demanded,remains unattainable and challenging.Here,a simple and transfer-free synthesis of high-quality doped graphene on the dielectric substrate has been developed using a thin Cu layer as the top catalyst and polycyclic aromatic hydrocarbons as both carbon precursors and doping sources.N-doped and N,F-co-doped graphene have been achieved using TPB and F16Cu Pc as solid carbon sources,respectively.The growth conditions were systematically optimized and the as-grown doped graphene were well characterized.The growth strategy provides a controllable transfer-free route for high-quality doped graphene synthesis,which will facilitate the practical applications of graphene.

Analysis of phosphate-accumulating organisms cultivated under different carbon sources with polymerase chain reaction-denaturing gradient gel electrophoresis assay

To investigate the microbial communities of microorganisms cultivated under different carbon sources, three sequencing batch reactors were operated. They were supplied with sewage, glucose and sodium acetate as carbon sources respectively and showed high phosphorus removal performance. The results of denaturing gradient gel electrophoresis(DGGE) of polymerase chain reaction-amplified(PCR) 16S rDNA fragments demonstrated that β-protebacteria, Actinomyces sp. and γ-protebacteria only exited in 1# reactor. The microbiological diversity of 1# reactor exceeded the other two reactors. Flavobacterium, Bacillales, Actinomyces, Actinobacteridae and uncultured bacteria(AF527584, AF502204, AY592749, AB076862, AJ619051, AF495454 and AY133070) could be detected in the biological phosphorus removal reactors.

G protein and MAPK signaling pathways control the ability of <i>Cochliobolus heterostrophus</i>to exploit different carbon sources

Phytopathogenic fungi are heterotrophic organisms that excrete a complex array of enzymes for digestion of plant host tissues. Regulation and coordination of extracellular enzyme production, according to growth conditions and fungus nutritional needs, may be controlled by conserved eukaryotic signaling elements such as G-protein subunits and mitogen-activated protein kinase (MAPK). These pathways are known to mediate a complex set of responses in fungi involved in development, reproduction and pathogenicity. Here, we used a series of mutants, deficient in G-protein α (cga1) or/and β subunits or in MAPK, to test their contribution to the ability of Cochliobolus heterostrophus to utilize different carbon sources. In saprophytic culture, the G-protein α subunit mutant strains had WT levels of cellulase, pectinase and protease degradation activities, but it grew significantly slower on minimal medium containing maltose. This weakened ability implies an essential role of the CGA1 signaling in some poor nutritional environments. Remarkably, the MAPK null mutant failed to achieve the WT (and cga1) growth rate on cellulose as a sole carbon and did not grow at all for the first seven days of culture. An enzymatic activity test revealed that this strain significantly reduced cellulose extracellular degradation activity when grew on this medium. Deficiency in the MAPK encoding gene also led to reduced ability to grow on pectin, protein sources and maltose as a sole carbon. The evidence presented indicates a significant and nutrient-specific role of the G-protein and MAPK pathways in mediating growth of this fungus in different environments.

The Effects of Different Carbon Sources on the Growth of <i>Rhodobacter sphaeroides</i>

Rhodobacter sphaeroides is a purple non-sulfur bacterium that belongs to the α-3 subdivision of Proteobacteria. R. sphaeroides is a model bacterial species because of its complex genome structure and expanded metabolic capabilities. The genome of R. sphaeroides consists of two circular chromosomes and five endogenous plasmids. It has the ability to grow under a wide variety of environmental conditions. It grows aerobically (~20% O2), semi-aerobically (~2% O2), and photosynthetically (under anaerobic condition plus light). It has been previously shown that many bacterial species utilize a number of alternate carbon sources for their optimal growth under a variety of growth conditions. We hypothesize that different or an additional carbon source in the minimal medium differentially affects the bacterial growth under dark-aerobic conditions. The bacterial growth kinetics and the number of cells in the bacterial culture were analyzed by measuring the optical density (OD at 600 nm) and the colony forming units (CFUs) at regular intervals of bacterial cultures. Results reveal that sodium succinate is the preferred sole carbon source for the optimal growth of R. sphaeroides. The results of growth kinetics and CFUs together concluded that from the tested carbon sources, sodium succinate is the best single carbon source in the minimal media for the optimal growth of R. sphaeroides. Interestingly, cell culture grown in SIS supplemented with sodium acetate exhibits a prolonged lag phase with the lowest ODs and CFUs that later switches to the growth-burst phase support previously discovered similar phenomenon of the growth-rate switch in the presence of acetate metabolism. Future work will utilize the aerobically grown R. sphaeroides’ cells as a biocatalyst to deplete the oxygen levels from natural gas streams and industrial gas pipelines.

Production and characterization of exopolysaccharides in mycelial culture of Cordyceps sinensis fungus Cs-HK1 with different carbon sources

The effects of different carbon sources(sugars) on the production and molecular properties of exopolysaccharides(EPS) were evaluated in the mycelial liquid culture of a medicinal fungus Cordyceps sinensis Cs-HK1. Galactose or mannose was used(at 5 g·L^(-1)) as a secondary carbon source with glucose(35 g·L^(-1)) at the mass ratio of 1:7. Mannose was consumed notably since the first day of culture, but galactose was not even after glucose was exhausted.The volumetric yield of EPS in culture was increased slightly with the addition of galactose and decreased with mannose. The monosaccharide composition of EPS was also different, e.g., on day 8, the glucose contents of EPS were 76%with the addition of mannose, 59% with galactose, compared with 62% with glucose only. The molecular weight distribution of EPS was also affected by the secondary carbon source, being generally lower compared with that with glucose only. The results suggested that the addition of galactose improved the total yield of EPS in culture while mannose can improve the yield of glucan constituent of EPS.

Production of Poly（3-hydroxybutyrate-co-3-hydroxyhexanoate） by Recombinant Pseudomonas stutzeri 1317 from Unrelated Carbon Sources

合成生物学诺言将由装配整个小径的分开的模块简化新陈代谢的小径的构造。这为象 polyhydroxyalkanoates (公众房产管理局) 那样的工业产品的微生物引起的生产给新途径。在这研究，(3-hydroxybutyrate-co-3-hydroxyhexanoate )(PHBHHx ) 由 Pseudomonas stutzeri， 1317 从无关的碳采购原料 poly 生产例如葡萄糖， P 的 phaC1-phaZ-phaC2 操纵子。stutzeri 1317 被击倒产生 PHA 缺乏的变异的 P。stutzeri 1317LF。然后，包含 phaCAhAReBRe， phaCAhBReGPp 和 phaCAhPAh 的三个模块被介绍进 P。stutzeri 1317LF 独立。饮料烧瓶结果显示先锋供应和公众房产管理局 synthase 活动是为 P 的 PHBHHx 累积的重要因素。stutzeri 1317LF。而且，从不同的碳资源的 recombinants 的 PHBHHx 累积被执行。最高的 PHBHHx 内容是 23.7%( 由质量) 与 58.6%( 由鼹鼠) 3HB 部分。这些结果为进一步改进 P 的 PHBHHx 累积提供基础。从无关的碳来源的 stutzeri。

Effects of Different Carbon Sources and NaBr-KCl on Synthesis of Ti(C,N)

Ti（ C, N） was synthesized with the starting materials of 76. 9% titania white and 23. 1% carbon black （graphite or activated carbon ）, or 40% titania white and 60% amylum, with or without 10% NaBr - KCl, dry moulding and carbon embedded firing at i 300 ℃ and 1 400 ℃ for 3 h, respectively. Phase composition and microstructure of the synthesized Ti （C, N） were analyzed by XRD, SEM and EPMA. Effects of different carbon sources and NaBr-KCl on the synthesis of Ti（ C, N） were investigated. The results show that： （1） Ti （C, N） can be synthesized by using carbon black, graphite, activated carbon or amylum as carbon source separately; （2） Additive NaBr - KCl is more favorable for accelerating the carbothermal reduction reaction using carbon black or amylum as carbon source; （3） In the presence of NaBr - KCl, particle size of the synthesized Ti（ C, N） is 5 -8μm using carbon black as carbon source fired at 1 300 ℃ for 3 h, while that is only 1 - 3 μm using graphite, activated carbon or amylum fired at 1 400 ℃ for 3 h.

Measurement of k_(eff) by delayed neutron multiplication in subcritical systems

In this paper, we build on the concept of equivalent fundamental-mode source to propose using delayed neutrons as a neutron source in multiplication experiments to acquire the effective multiplication factor keffof subcritical systems, which is difficult to acquire directly from conventional neutron source multiplication method. We analyzed the difference between a fundamental-mode fission source and delayed neutron source,then adopted a factor to convert delayed neutron distribution to an equivalent fundamental-mode source distribution, and employed Monte Carlo code to acquire this factor.The delayed neutron multiplication measurement method was established for the first time, and corresponding experiments were conducted in subcritical systems. The multiplication of delayed neutrons was measured based on Chinese Fast Burst Reactor-Ⅱ(CFBR-Ⅱ) at subcritical states, and keffwas acquired from delayed neutron multiplication successfully(0.9921 and 0.9969, respectively).The relative difference between k_(eff)obtained by the new method and previous values acquired by the positive period method is less than 1% for these two studied cases.

Measurement of k_(eff) with an improved neutron source multiplication method based on numerical analysis

In this work,we developed a numerical analysis-associated experiment method to determine the effective multiplication factor k_(eff),which is difficult to obtain directly from conventional neutron source multiplication(NSM)method.The method is based on the relationship between k_(eff),subcritical multiplication factor k_s and external neutron source efficiency Φ~* in the subcritical system.On basis of the theoretical analysis,the dependence of k_s and Φ~* on subcriticality and source position was investigated at the Chinese Fast Burst Reactor-Ⅱ(CFBR-Ⅱ).A series of k_s were measured by NSM experiments at four subcritical states(k_(eff) = 0.996,0.994,0.991 and0.986) with the ^(252)Cf neutron source located at different positions(from the system center to outside) at each subcritical states.The Φ~* was obtained by Monte-Carlo simulation for each condition.With the measured k_s and calculated Φ~*,k_(eff) of the subcritical system was evaluated with a relative difference of < 1%between values obtained by the improved method and by positive period method.Especially,the relative difference of < 0.18%with the source located at the system center.

Full-domain collaborative deployment method of multiple interference sources and evaluation of its deployment effect

This paper realizes the full-domain collaborative deployment of multiple interference sources of the global satellite navigation system(GNSS)and evaluates the deployment effect to enhance the ability to disturb the attacker and the capability to defend the GNSS during navigation countermeasures.Key evaluation indicators for the jamming effect of GNSS suppressive and deceptive jamming sources are first created,their evaluation models are built,and their detection procedures are sorted out,as the basis for determining the deployment principles.The principles for collaboratively deploying multi-jamming sources are developed to obtain the deployment structures(including the required number,structures in demand,and corresponding positions)of three single interference sources required by collaboratively deploying.Accordingly,simulation and hardware-in-loop testing results are presented to determine a rational configuration of the collaborative deployment of multi-jamming sources in the set situation and further realize the full-domain deployment of an interference network from ground,air to space.Varied evaluation indices for the deployment effect are finally developed to evaluate the deployment effect of the proposed configuration and further verify its reliability and rationality.

Persistence of fertilization effects on soil organic carbon in degraded alpine wetlands in the Yellow River source region

In the restoration of degraded wetlands,fertilization can improve the vegetation-soil-microorganisms complex,thereby affecting the organic carbon content.However,it is currently unclear whether these effects are sustainable.This study employed Biolog-Eco surveys to investigate the changes in vegetation characteristics,soil physicochemical properties,and soil microbial functional diversity in degraded alpine wetlands of the source region of the Yellow River at 3 and 15 months after the application of nitrogen,phosphorus,and organic mixed fertilizer.The following results were obtained:The addition of nitrogen fertilizer and organic compost significantly affects the soil organic carbon content in degraded wetlands.Three months after fertilization,nitrogen addition increases soil organic carbon in both lightly and severely degraded wetlands,whereas after 15 months,organic compost enhanced the soil organic carbon level in severely degraded wetlands.Structural equation modeling indicates that fertilization decreases the soil pH and directly or indirectly influences the soil organic carbon levels through variations in the soil water content and the aboveground biomass of vegetation.Three months after fertilization,nitrogen fertilizer showed a direct positive effect on soil organic carbon.However,organic mixed fertilizer indirectly reduced soil organic carbon by increasing biomass and decreasing soil moisture.After 15 months,none of the fertilizers significantly affected the soil organic carbon level.In summary,it can be inferred that the addition of nitrogen fertilizer lacks sustainability in positively influencing the organic carbon content.

Carbon efficiency evaluation method for urban energy system with multiple energy complementary

Urban energy systems(UESs)play a pivotal role in the consumption of clean energy and the promotion of energy cascade utilization.In the context of the construction and operation strategy of UESs with multiple complementary energy resources,a comprehensive assessment of the energy efficiency is of paramount importance.First,a multi-dimensional evaluation system with four primary indexes of energy utilization,environmental protection,system operation,and economic efficiency and 21 secondary indexes is constructed to comprehensively portray the UES.Considering that the evaluation system may contain a large number of indexes and that there is overlapping information among them,an energy efficiency evaluation method based on data processing,dimensionality reduction,integration of combined weights,and gray correlation analysis is proposed.This method can effectively reduce the number of calculations and improve the accuracy of energy efficiency assessments.Third,a demonstration project for a UES in China is presented.The energy efficiency of each scenario is assessed using six operational scenarios.The results show that Scenario 5,in which parks operate independently and investors build shared energy-storage equipment,has the best results and is best suited for green and low-carbon development.The results of the comparative assessment methods show that the proposed method provides a good energy efficiency assessment.This study provides a reference for the optimal planning,construction,and operation of UESs with multiple energy sources.

In situ formation of multiple catalysts for enhancing the hydrogen storage of MgH_(2) by adding porous Ni_(3)ZnC_(0.7)/Ni loaded carbon nanotubes microspheres

MgH_(2) is considered one of the most promising hydrogen storage materials because of its safety,high efficiency,high hydrogen storage quantity and low cost characteristics.But some shortcomings are still existed:high operating temperature and poor hydrogen absorption dynamics,which limit its application.Porous Ni_(3)ZnC_(0.7)/Ni loaded carbon nanotubes microspheres(NZC/Ni@CNT)is prepared by facile filtration and calcination method.Then the different amount of NZC/Ni@CNT(2.5,5.0 and 7.5 wt%)is added to the MgH_(2) by ball milling.Among the three samples with different amount of NZC/Ni@CNT(2.5,5.0 and 7.5 wt%),the MgH_(2)-5 wt%NZC/Ni@CNT composite exhibits the best hydrogen storage performances.After testing,the MgH_(2)-5 wt%NZC/Ni@CNT begins to release hydrogen at around 110℃ and hydrogen absorption capacity reaches 2.34 wt%H_(2) at 80℃ within 60 min.Moreover,the composite can release about 5.36 wt%H_(2) at 300℃.In addition,hydrogen absorption and desorption activation energies of the MgH_(2)-5 wt%NZC/Ni@CNT composite are reduced to 37.28 and 84.22 KJ/mol H_(2),respectively.The in situ generated Mg_(2)NiH_(4)/Mg_(2)Ni can serve as a"hydrogen pump"that plays the main role in providing more activation sites and hydrogen diffusion channels which promotes H_(2) dissociation during hydrogen absorption process.In addition,the evenly dispersed Zn and MgZn2 in Mg and MgH_(2) could provide sites for Mg/MgH_(2) nucleation and hydrogen diffusion channel.This attempt clearly proved that the bimetallic carbide Ni_(3)ZnC_(0.7) is a effective additive for the hydrogen storage performances modification of MgH_(2),and the facile synthesis of the Ni_(3)ZnC_(0.7)/Ni@CNT can provide directions of better designing high performance carbide catalysts for improving MgH_(2).

Interfacial design of silicon/carbon anodes for rechargeable batteries:A review

Silicon(Si)has been studied as a promising alloying type anode for lithium-ion batteries due to its high specific capacity,low operating potential and abundant resources.Nevertheless,huge volume expansion during alloying/dealloying processes and low electronic conductivity of Si anodes restrict their electrochemical performance.Thus,carbon(C)materials with special physical and chemical properties are applied in Si anodes to effectively solve these problems.This review focuses on current status in the exploration of Si/C anodes,including the lithiation mechanism and solid electrolyte interface formation,various carbon sources in Si/C anodes,such as traditional carbon sources(graphite,pitch,biomass),and novel carbon sources(MXene,graphene,MOFs-derived carbon,graphdiyne,etc.),as well as interfacial bonding modes of Si and C in the Si/C anodes.Finally,we summarize and prospect the selection of carbonaceous materials,structural design and interface control of Si/C anodes,and application of Si/C anodes in all-solid-state lithium-ion batteries and sodium-ion batteries et al.This review will help researchers in the design of novel Si/C anodes for rechargeable batteries.

Direct chemical vapor deposition growth of graphene on Ni particles using solid carbon sources

Graphene has attained a considerable amount of popularity as an attractive ultra-thin reinforcement for nickel(Ni)matrix composites in recent years.However,its excellent reinforcement efficiency is suffered from the agglomeration of graphene nanosheets in manufacturing process and the poor bonding strength of graphene with Ni matrix.To overcome these two problems,one of the efficient strategies is to in-situ grow graphene reinforcements on Ni particles for powder metallurgy.This work aims to synthesize uniform graphene@Ni composite particles by using polymethyl methacrylate(PMMA)as the solid sources for chemical vapor deposition(CVD)process.The results demonstrate that few-layer or multilayer graphene with different morphologies can be grown on the particles by controlling the PMMA content and annealed temperature,respectively.The optimum condition for the formation of high-quality few-layer graphene is 1.0 mg·ml^(-1) PMMA and 900℃.A competition mechanism rises from the growth kinetic,and the spatial confinement effect has led to the formation of graphene with different microstructures and morphologies.

The status and development proposal of carbon sources and sinks monitoring satellite system

In order to mitigate global warming,the international communities actively explore low-carbon and green development methods.According to the Paris Agreement that came into effect in 2016,there will be a global stocktaking plan to carry out every 5 years from 2023 onwards.In September 2020,China proposed a"double carbon"target of carbon peaking before 2030 and carbon neutrality before 2060.Achieving carbon peaking and carbon neutrality goals requires accurate carbon emissions and carbon absorptions.China’s existing carbon monitoring methods have insufficient detection accuracy,low spatial resolution,and narrow swath,which are difficult to meet the monitoring requirement of carbon sources and sinks monitoring.In order to meet the needs of carbon stocktaking and support the monitoring and supervision of carbon sources and sinks,it is recommended to make full use of the foundation of the existing satellites,improve the detection technical specifications of carbon sources and sinks monitoring measures,and build a multi-means and comprehensive,LEO-GEO orbit carbon monitoring satellite system to achieve higher precision,higher resolution and multi-dimensional carbon monitoring.On this basis,it is recommended to strengthen international cooperation,improve data sharing policy,actively participate in the development of carbon retrieval algorithm and the setting of international carbon monitoring standards,establish an independent and controllable global carbon monitoring and evaluation system,and contribute China’s strength to the global realization of carbon peaking and carbon neutrality.

Organic Carbon in the Surface Sediments from the Intensive Mariculture Zone of Sanggou Bay: Distribution, Seasonal Variations and Sources

Mariculture has rapidly grown worldwide, which might greatly influence the biogeochemical cycle of organic carbon in coastal seas. In this study, several geochemical parameters, including grain size composition, sedimentary total organic carbon (TOC), total nitrogen (TN), stable carbon (δ13C) and nitrogen (δ15N) isotopic compositions, were analyzed for surface sediments collected from different mariculture zones of Sanggou Bay and in different seasons. We investigated the composition and distribution of or- ganic matter in surface sediments and further evaluated the contribution of mariculture activities to TOC sources. The TOC and TN contents (mass percentage) in the bay were in the range of 0.14% to 1.45% and 0.03% to 0.20%, respectively. The spatial distribution indicated that sedimentary TOC and TN contents in shellfish monoculture and shellfish-kelp polyculture zones were higher than in other mariculture zones, which might be related to grain size composition and mariculture organisms. Seasonal variations of TOC contents were observed in different mariculture zones. The TOC/TN atomic ratio (C/N),δ13C and δ15N were in the ranges of 5.97 to 10.97, 21.76‰ to 13.14‰ and 2.13‰ to 8.08‰, respectively, implying that sedimentary organic matter in Sanggou Bay was the mixture of marine phytoplankton, terrestrial and maricultural sources. A simple mixing model based on δ13C was applied and the results indicated that the relative contributions of organic carbon sources in Sanggou Bay followed the order kelp (36.6%) marine phytoplankton (28.7%) shellfish bio-deposition (23.8%) terrestrial input (10.9%). Surface sediments in Sanggou Bay were domi- nated by mariculture-derived organic carbon, which on average accounted for 60.4% of TOC.