Experimental study of the effects of a multistage pore-throat structure on the seepage characteristics of sandstones in the Beibuwan Basin:Insights into the flooding mode

To investigate the relationship between grain sizes, seepage capacity, and oil-displacement efficiency in the Liushagang Formation of the Beibuwan Basin, this study identifies the multistage pore-throat structure as a crucial factor through a comparison of oil displacement in microscopic pore-throat experiments. The two-phase flow evaluation method based on the Li-Horne model is utilized to effectively characterize and quantify the seepage characteristics of different reservoirs, closely relating them to the distribution of microscopic pores and throats. It is observed that conglomerate sandstones at different stages exhibit significant heterogeneity and noticeable differences in seepage capacity, highlighting the crucial role played by certain large pore throats in determining seepage capacity and oil displacement efficiency. Furthermore, it was found that the displacement effects of conglomeratic sandstones with strong heterogeneity were inferior to those of conventional homogeneous sandstone, as evidenced by multiple displacement experiments conducted on core samples with varying granularities and flooding systems. Subsequently, core-based experiments on associated gas flooding after water flooding were conducted to address the challenge of achieving satisfactory results in a single displacement mode for reservoirs with significant heterogeneity. The results indicate that the oil recovery rates for associated gas flooding after water flooding increased by 7.3%-16.4% compared with water flooding alone at a gas-oil ratio of approximately 7000 m^(3)/m^(3). Therefore, considering the advantages of gas flooding in terms of seepage capacity, oil exchange ratio, and the potential for two-phase production, gas flooding is recommended as an energy supplement mode for homogeneous reservoirs in the presence of sufficient gas source and appropriate tectonic angle. On the other hand, associated gas flooding after water flooding is suggested to achieve a more favorable development effect compared to a single mode of energy supplementation for strongly heterogeneous sandstone reservoirs.

Modified Sadowski formula-based model for the slope shape amplification effect under multistage slope blasting vibration

Blasting operations,which are crucial to open-pit mine production due to their simplicity and efficiency,require precise control through accurate vibration velocity calculations.The conventional Sadowski formula mainly focuses on blast center distance but neglects the amplification effect of blasting vibration waves by terraced terrain,from which the calculated blasting vibration velocities are smaller than the actual values,affecting the safety of the project.To address this issue,our model introduces the influences of slope and time into Sadowski formula to measure safety through blast vibration displacement.In the northern section of the open-pit quartz mine in Jinchang City,Gansu Province,China,the data of a continuous blasting slope project are referred to.Our findings reveal a noticeable vibration amplification effect during blasting when a multi-stage slope platform undergoes a sudden cross-sectional change near the upper overhanging surface.The amplification vibration coefficient increases with height,while vibration waves within rocks decrease from bottom to top.Conversely,platforms without distinct crosssectional changes exhibit no pronounced amplification during blasting.In addition,the vibration intensity decreases with distance as the rock height difference change propagates.The results obtained by the proposed blast vibration displacement equation incorporating slope shape influence closely agree with real-world scenarios.According to Pearson correlation coefficient(PPMCC)analysis,the average accuracy rate of our model is 88.84%,which exceeds the conventional Sadowski formula(46.92%).

Multistage hydraulic fracturing of a horizontal well for hard roof related coal burst control:Insights from numerical modelling to field application

Multistage hydraulic fracturing of horizontal wells(MFHW)is a promising technology for controlling coal burst caused by thick and hard roofs in China.However,challenges remain regarding the MFHW control mechanism of coal burst and assessment of the associated fracturing effects.In this study,these challenges were investigated through numerical modelling and field applications,based on the actual operating parameters of MFHW for hard roofs in a Chinese coal mine.A damage parameter(D)is proposed to assess the degree of hydraulic fracturing in the roof.The mechanisms and effects of MFHW for controlling coal burst are analyzed using microseismic(MS)data and front-abutment stress distribution.Results show that the degree of fracturing can be categorized into lightly-fractured(D≤0.3),moderately fractured(0.3<D≤0.6),well-fractured(0.6<D≤0.9),and over-fractured(0.9<D≤0.95).A response stage in the fracturing process,characterized by a slowdown in crack development,indicates the transition to a wellfractured condition.After MFHW,the zone range and peak value of the front-abutment stress decrease.Additionally,MS events shift from near the coal seam to the fractured roof layers,with the number of MS events increases while the average MS energy decreases.The MFHW control mechanisms of coal bursts involve mitigating mining-induced stress and reducing seismic activity during longwall retreat,ensuring stresses remain below the ultimate stress level.These findings provide a reference for evaluating MFHW fracturing effects and controlling coal burst disasters in engineering.

Characteristics and demographic factors of traditional Chinese medicine constitution types among elderly individuals in China:A national multistage cluster random study Author links open overlay panel

Objective:To reveal the distribution characteristics and demographic factors of traditional Chinese medicine(TCM)constitution among elderly individuals in China.Methods: Elderly individuals from seven regions in China were selected as samples in this study using a multistage cluster random sampling method.The basic information questionnaire and Constitution in Chinese Medicine Questionnaire(Elderly Edition)were used.Descriptive statistical analysis,chi-squared tests,and binary logistic regression analysis were used.Results: The single balanced constitution(BC)accounted for 23.9%.The results of the major TCM constitution types showed that BC(43.2%)accounted for the largest proportion and unbalanced constitutions ranged from 0.9%to 15.7%.East China region(odds ratio[OR]=2.097;95%confidence interval[CI],1.912 to 2.301),married status(OR=1.341;95%CI,1.235 to 1.457),and managers(OR=1.254;95%CI,1.044 to 1.505)were significantly associated with BC.Age>70 years was associated with qi-deficiency constitution and blood stasis constitution(BSC).Female sex was significantly associated with yang-deficiency constitution(OR=1.646;95%CI,1.52 to 1.782).Southwest region was significantly associated with phlegm-dampness constitution(OR=1.809;95%CI,1.569 to 2.086).North China region was significantly associated with inherited special constitution(OR=2.521;95%CI,1.569 to 4.05).South China region(OR=2.741;95%CI,1.997 to 1.3.763),Central China region(OR=8.889;95%CI,6.676 to 11.835),senior middle school education(OR=2.442;95%CI,1.932 to 3.088),and managers(OR=1.804;95%CI,1.21 to 2.69)were significantly associated with BSC.Conclusions: This study defined the distribution characteristics and demographic factors of TCM constitution in the elderly population.Adjusting and improving unbalanced constitutions,which are correlated with diseases,can help promote healthy aging through the scientific management of these demographic factors.

Multistage Stochastic Programming Model for the Portfolio Problem of a Property-Liability Insurance Company

The current portfolio model for property-liability insurance company is only single period that can not meet the practical demands of portfolio management, and the purpose of this paper is to develop a multiperiod model for its portfolio problem. The model is a multistage stochastic programming which considers transaction costs, cash flow between time periods, and the matching of asset and liability; it does not depend on the assumption for normality of return distribution. Additionally, an investment constraint is added. The numerical example manifests that the multiperiod model can more effectively assist the property-liability insurer to determine the optimal composition of insurance and investment portfolio and outperforms the single period one.

Construction of Early-warning Model for Plant Diseases and Pests Based on Improved Neural Network

By studying principles and methods related to early-warning model of plant diseases and using PSO method, parameter optimization was conducted to backward propagation neural network, and a pre-warning model for plant diseases based on particle swarm and neural network algorithm was established. The test results showed that the construction of early-warning model is effective and feasible, which will provide a via- ble model structure to establish the effective early-warning platform.

Multistage Extension and Age Dating of the Xiaoqinling Metamorphic Core Complex,Central China

Abstract There are two extensional systems in the Xiaoqinling metamorphic core complex (XMCC). One is the detachment fault system developed along the peripheries of the XMCC, which extended in an ESE-WNW direction and whose upper plate moved towards the WNW. The other extensional system includes the retrograde shear zones and normal faults developed within the XMCC, which represent the collapse of the XMCC. Ar-Ar and K-Ar dating shows that the extension of the detachment fault system continued from 135 to 123 Ma, i.e. in the late stage of its evolution at about 127 Ma. The collapse represented by the extensional system within the XMCC was operative during 120–106 Ma, and its main activity occurred about 116 Ma ago. These suggest that the XMCC experienced two extensional stages in its evolution, i.e., the syn-orogenic regional extension and post-orogenic collapse extension.

Bayesian synthetic evaluation of multistage reliability growth with instant and delayed fix modes

In the multistage reliability growth tests with instant and delayed fix modes, the failure data can be assumed to follow Weibull processes with different parameters at different stages. For the Weibull process within a stage, by the proper selection of prior distribution form and the parameters, a concise posterior distribution form is obtained, thus simplifying the Bayesian analysis. In the multistage tests, the improvement factor is used to convert the posterior of one stage to the prior of the subsequent stage. The conversion criterion is carefully analyzed to determine the distribution parameters of the subsequent stage＇s variable reasonably. Based on the mentioned results, a new synthetic Bayesian evaluation program and algorithm framework is put forward to evaluate the multistage reliability growth tests with instant and delayed fix modes. The example shows the effectiveness and flexibility of this method.

Experimental mass transfer coefficients in a pilot plant multistage column extractor

The volumetric overall mass transfer coefficients in a multistage column have been measured using axial dispersion model for toluene–acetone–water system. The effect of operating parameters on the volumetric overall mass transfer coefficients has been investigated for both mass transfer directions. The results show that the mass transfer performance is strongly dependent on rotor speed and mass transfer direction, although only slightly dependent on phase flow rates. In addition, empirical correlations to predict the overall mass transfer coefficients have been developed. The proposed correlations based on dimensionless numbers can be considered as a useful tool for the possible scale up of the multistage column extractor.

Multistage Enrichment of the Sawafuqi Uranium Deposit: New Insights into Sandstone-hosted Uranium Deposits in the Intramontane Basins of Tian Shan, China

Meso-Cenozoic intracontinental orogenic processes in the Tian Shan orogenic belt have significant effect on the sandstone-hosted uranium deposits in the intramontane basins and those adjacent to the orogen. The Sawafuqi uranium deposit, which is located in the South Tian Shan orogenic belt, is investigated to reveal the relationships between uranium mineralization and orogenies. Recent exploration results show that the Sawafuqi uranium deposit has tabular, stratiform, quasi-stratiform, and lens-like orebodies and various geological characteristics different from typical interlayer oxidation zone sandstone-hosted uranium deposits. Systematic studies of ore samples from the Sawafuqi uranium deposit using a variety of techniques, including thin section observation, a-track radiograph, electron microprobe and scanning electron microscope, suggest that uranium mineralization is closely related to pyrite and organic matter. Mineralization-related alterations in the host rocks are mainly silicification and argillation including kaolinite, illite （and illite-smectite mixed layer） and chlorite. Tree stages of mineralization were identified in the Sawafuqi uranium deposit： （i） uranium-bearing detritus and synsedimentary initial pre-enrichment; （ii） interlayer oxidization zone uranium mineralization; and （iii） vein-type uranium mineralization. The synsedimentary uranium pre-enrichment represents an early uranium enrichment in the Sawafuqi uranium deposit, and interlayer oxidation zone uranium mineralization formed the main orebodies, which are superimposed by the vein-type uranium mineralization. Combining the results of this study with previous studies on the Meso-Cenozoic orogenies of South Tian Shan, it is proposed that the synsedimentary uranium pre-enrichment of the Sawafuqi uranium deposit was caused by Triassic Tian Shan uplift, and the interlayer oxidation zone uranium mineralization occurred during the Eocence-Oligocene period, when tectonism was relatively quiet, whereas the vein-type uranium mineralization took place in relation to the strong orogeny of South Tian Shan since Miocene.

FINITE ELEMENT SIMULATION AND OPTIMIZATION OF MULTISTAGE WARM/HOT FORMING FOR OUTER RACE

A multistage warm/hot forming is simulated for the cross grove outer race ofconstant velocity joint, using a thermo-mechanical coupled rigid viscoplastic finite element method,and specially some problem for process development and die design are analyzed. A forming testshows that computed results have good agreement with experimental results. Above obtained resultscan be applied to development of multistage warm/hot forming process and die design for outer race.

Variable selection-based SPC procedures for high-dimensional multistage processes

Monitoring high-dimensional multistage processes becomes crucial to ensure the quality of the final product in modern industry environments. Few statistical process monitoring(SPC) approaches for monitoring and controlling quality in highdimensional multistage processes are studied. We propose a deviance residual-based multivariate exponentially weighted moving average(MEWMA) control chart with a variable selection procedure. We demonstrate that it outperforms the existing multivariate SPC charts in terms of out-of-control average run length(ARL) for the detection of process mean shift.

China agricultural outlook for 2015–2024 based on China Agricultural Monitoring and Early-warning System(CAMES)

The primary goal of Chinese agricultural development is to guarantee national food security and supply of major agricultural products. Hence, the scientiifc work on agricultural monitoring and early warning as wel as agricultural outlook must be strengthened. In this study, we develop the China Agricultural Monitoring and Early-warning System (CAMES) on the basis of a comparative study of domestic and international agricultural outlook models. The system is a dynamic and multi-market partial equilibrium model that integrates biological mechanisms with economic mechanisms. This system, which includes 11 categories of 953 kinds of agricultural products, could dynamical y project agricultural market supply and demand, assess food security, and conduct scenario analysis at different spatial levels, time scale levels, and macro-micro levels. Based on the CAMES, the production, consumption, and trade of the major agricultural products in China over the next decade are projected. The fol owing conclusions are drawn:i) The production of major agricultural products wil continue to grow steadily, mainly because of the increase in yield. i ) The growth of agricultural consumption wil be slightly higher than that of agricultural production. Meanwhile, a high self-sufifciency rate is expected for cereals such as rice, wheat, and maize, with the rate being stable at around 97%. i i) Agricultural trade wil continue to thrive. The growth of soybean and milk im-ports wil slow down, but the growth of traditional agricultural exports such as vegetables and fruits is expected to continue.

Charcoal Production via Multistage Pyrolysis

Interests in charcoal usage have recently been re-ignited because it is believed that charcoal is a muchbetter fuel than wood. The conventional charcoal production consumes a large amount of energy due to the prolonged heating time and cooling time which contribute to the process completing in one to several days. Wood py-rolysis consists of both endothermic and exothermic reactions as well as the decomposition of the different components at different temperature range （hemicellulose： 200-260℃; cellulose： 240-350℃ and lignin： 280-500℃）. Inthis study we propose a multistagepyrolysis which is an approach to carry out pyrolysis with multiple heating stages so as to gain certain processing benefits. We propose a three-stage approach which includes rapid stepwise heating stage to a variable target temperatures of 250 ℃, 300℃, 350 ℃ and 400 ℃, slow and gradual heatingstage to a tinal temperature of 400℃ and adiabatic with cooling stage. The multi-stage pyrolysis process can save 30% energy and the processing time by using a first temperature target of 300 ℃and heating rate of 5℃.min-1 to produce a fixed-carbon yield of 25.73% as opposed to the base case with a fixed-carbon yield of23.18%.

Deformation early-warning index for heightened gravity dam during impoundment period

The mechanical parameters of materials in a dam body and dam foundation tend to change when dams are reinforced in aging processes.It is important to use an early-warning index to reflect the safety status of dams,particularly of heightened projects in the impoundment period.Herein,a new method for monitoring the safety status of heightened dams is proposed based on the deformation monitoring data of a dam structure,a statistical model,and finite-element numerical simulation.First,a fast optimization inversion method for estimation of dam mechanical parameters was developed,which used the water pressure component extracted from a statistical model,an improved inversion objective function,and a genetic optimization iterative algorithm.Then,a finite element model of a heightened concrete gravity dam was established,and the deformation behavior of the dam with rising water levels in the impoundment period was simulated.Subsequently,mechanical parameters of aged dam parts were calculated using the fast optimization inversion method with simulated deformation and the water pressure deformation component obtained by the statistical model under the same conditions of water pressure change.Finally,a new earlywarning index of dam deformation was constructed by means of the forward-simulated deformation and other components of the statistical model.The early-warning index is useful for forecasting dam deformation under different water levels,especially high water levels.

Microstructure Design of High-Entropy Alloys Through a Multistage Mechanical Alloying Strategy for Temperature-Stable Megahertz Electromagnetic Absorption

Developing megahertz(MHz)electromagnetic wave(EMW)absorption materials with broadband absorption,multi-temperature adaptability,and facile preparation method remains a challenge.Herein,nanocrystalline FeCoNiCr_(0.4)Cu_(0.2) high-entropy alloy powders(HEAs)with both large aspect ratios and thin intergranular amorphous layers are constructed by a multistage mechanical alloying strategy,aiming to achieve excellent and temperature-stable permeability and EMW absorption.A single-phase face-centered cubic structure with good ductility and high crystallinity is obtained as wet milling precursors,via precisely controlling dry milling time.Then,HEAs are flattened to improve aspect ratios by synergistically regulating wet milling time.FeCoNiCr_(0.4)Cu_(0.2) HEAs with dry milling 20 h and wet milling 5 h(D20)exhibit higher and more stable permeability because of larger aspect ratios and thinner intergranular amorphous layers.The maximum reflection loss(RL)of D20/SiO_(2) composites is greater than-7 dB with 5 mm thickness,and EMW absorption bandwidth(RL<-7 dB)can maintain between 523 and 600 MHz from-50 to 150℃.Furthermore,relying on the“cocktail effect”of HEAs,D20 sample also exhibits excellent corrosion resistance and high Curie temperature.This work provides a facile and tunable strategy to design MHz electromagnetic absorbers with temperature stability,broadband,and resistance to harsh environments.

Data Processing Model of Coalmine Gas Early-Warning System

The data processing mode is vital to the performance of an entire coalmine gas early-warning system, especially in real-time performance. Our objective was to present the structural features of coalmine gas data, so that the data could be processed at different priority levels in C language. Two different data processing models, one with priority and the other without priority, were built based on queuing theory. Their theoretical formulas were determined via a M/M/I model in order to calculate average occupation time of each measuring point in an early-warning program. We validated the model with the gas early-warning system of the Huaibei Coalmine Group Corp. The results indicate that the average occupation time for gas data processing by using the queuing system model with priority is nearly 1/30 of that of the model without priority.

Characteristics Analysis and the Early-warning Service System of Heavy Fog in Chizhou City

By analyzing the heavy fog data in Chizhou City in recent 50 years(1959-2007),the general rules of meteorological elements variations were found when the heavy fog happened.The meteorological elements included the temperature,humidity,wind direction,wind speed,air pressure and so on.The conceptual models of high-altitude and ground situation were established when the heavy fog happened in Chizhou City.Based on considering sufficiently the special geographical environment in Chizhou City,we found the key factors which affected the local heavy fog via the relative analyses.By using the statistical forecast methods which included the second-level judgment method and regression method of event probability and so on,the forecast mode equation of heavy fog was established.Moreover,the objective forecast system of heavy fog in Chizhou City was also manufactured.It provided the basis and platform which could be referred for the heavy fog forecast,service and the release of early-warning signal.

Improved Quality Prediction Model for Multistage Machining Process Based on Geometric Constraint Equation

Product variation reduction is critical to improve process efficiency and product quality, especially for multistage machining process（MMP）. However, due to the variation accumulation and propagation, it becomes quite difficult to predict and reduce product variation for MMP. While the method of statistical process control can be used to control product quality, it is used mainly to monitor the process change rather than to analyze the cause of product variation. In this paper, based on a differential description of the contact kinematics of locators and part surfaces, and the geometric constraints equation defined by the locating scheme, an improved analytical variation propagation model for MMP is presented. In which the influence of both locator position and machining error on part quality is considered while, in traditional model, it usually focuses on datum error and fixture error. Coordinate transformation theory is used to reflect the generation and transmission laws of error in the establishment of the model. The concept of deviation matrix is heavily applied to establish an explicit mapping between the geometric deviation of part and the process error sources. In each machining stage, the part deviation is formulized as three separated components corresponding to three different kinds of error sources, which can be further applied to fault identification and design optimization for complicated machining process. An example part for MMP is given out to validate the effectiveness of the methodology. The experiment results show that the model prediction and the actual measurement match well. This paper provides a method to predict part deviation under the influence of fixture error, datum error and machining error, and it enriches the way of quality prediction for MMP.

Design of Computationally Efficient Sharp FIR Filter Utilizing Modified Multistage FRM Technique for Wireless Communications Systems

Modern wireless communications gadgets demand multi-standard communications facilities with least overlap between different input radio channels. A sharp digital filter of extremely narrow transition-width with lower stop band ripples offers alias-free switching among the preferred frequency bands. A computationally competent low pass filter (LPF) structure based on the multistage frequency response masking (FRM) approach is proposed for the design of sharp finite impulse response (FIR) filters which are suitable for wireless communications applications. In comparison of basic FRM with other existing multistage FRM structures, the proposed structure has a narrow transition bandwidth and higher stop band attenuation with significant reduction in terms of the number of computational steps. A design example is incorporated to demonstrate the efficiency of the proposed approach. Simulation results establish the improvement of the proposed scheme over other recently published design strategies.