Detecting Impact Damage in Carbon Fabric/epoxy-matrix Composites by Ultrasonic F-scan and Electrical Resistance Measurement

The status and the variation of electrical resistance of impacted carbon fiber/epoxy-matrix composites were studied by ultrasonic F-scan and electrical resistance measurement The experimental results shows that impact damage energy threshold value of carbon fabric/epoxy-matrix composites can determine by using ultrasonic F-scan. When the impact energy exceeds the threshold value, damage is generated in composites. Electrical resistance of impacted composites is changed owing to the contact of each carbon fiber unit in composites, which cause a change of the series-parallel in conductors. The veracity of detecting impact damage in composites can be improved in this case.

Multilevel Tests and Measurement Evaluation Methods for the Application of Composite Materials in Spacecraft Structures

With the implementation of new-generation launch vehicles,space stations,lunar and deep space exploration,etc.,the development of spacecraft structures will face new challenges. In order to reduce the spacecraft weight and increase the payload,composite material structures will be widely used. It is difficult to evaluate the strength and life of composite materials due to their complex mechanism and various phenomena in damage and failure.Meanwhile,the structures of composite materials used in spacecrafts will bear complex loads,including the coupling loads of tension,pressure,bending,shear,and torsion. Static loads,thermal loads,and vibration loads may occur at the same time,which asks for verification requirements to ensure the structure safety. Therefore,it is necessary to carry out a systematic multi-level experimental study. In this paper,the building block approach (BBA) is used to investigate the multilevel composite material structures for spacecrafts. The advanced measurement technology is adopted based on digital image correlation (DIC) and piezoelectric and optical fiber sensors to measure the composite material structure deformation. The virtual experiment technology is applied to provide sufficient and reliable data for the evaluation of the composite material structures of spacecrafts.

STRAIN MEASUREMENT IN THE SMART COMPOSITE

The smart composite structure is a new type of structure developed in recent years. It can be used in aircraft or some other important devices. The smart composite structure in which some sensors, actuators and other components are embedded can perform the tasks such damage evaluation, strain measurement, changing stress and suppressing vibration by itself. In the Performance of the tasks above, many parameters must be measured, among which the measurement of strain field is very important. In this paper, some distributed and quasi-distributed embedding optic fiber strain sensors are introduced, and their specialities are discussed.

Evaluation of Impact Damage Tolerance in Carbon Fabric/epoxy-matrix Composites by Electrical Resistance Measurement

Impact damage tolerance is provided in intensity design on composites. The compression intensity of impacted composites requires more than 60% of its original intensity. The influence of impact on compressive intensity and electrical resistance of carbon fabric/epoxy-matrix composites was studied in this paper. The experimental results shows that impact can cause damage in composites, degenerate compressive intensity, and increase resistance. The electrical resistance change rate was used as an evaluation indicator of impact damage tolerance of composites. Impact damage, which results from the applying process of composites, can be identified in time by electrical resistance measurement. So, the safety performance of composites can also be improved.

MEASUREMENT OF INTERNAL STRESSES OF METAL MULTILAYER COMPOSITE COATINGS

The principle, formula and determination of internal stresses of metal multilayer composite coatings by means of the bending strip method were studied. Using this method, internal stresses of ion-plated metal multilayer composite coatings and thick monolayer coating of aluminium bronze, stainless steel and nickel-iron alloy were determined. The reason of decrement in internal stresses of multilayer composite coatings was discussed.

Design and research of magnetically levitated testbed with composite superconductor bearing for micro thrust measurement

A high temperature superconducting(HTS)magnetically levitated testbed has been developed for the steady thrust measurement of miniature ion electrospray thruster.The structure of the testbed mainly consists of an HTS composite bearing,a magnetic shielding plate,an active electromagnetic brake and a laser displacement sensor.The steady thrust is described as a function of the equilibrium angle displacement of the floating frame.Furthermore,the mechanical behaviors of HTS composite bearing were studied via finite element simulation and experiments,which include the load capacity,levitation stiffness and background noise.The results show that the thrust testbed can keep in low noise and have a load capacity up to 4 kg.According to the ignition testing of the electrospray thruster,the thrust force of 25.2 m N was measured by the testbed,which is close to the design value of miniature ion electrospray thruster.

Characterization of Reinforced Carbon Composites with Full Field Measurements: Long Gauge Length Compressive Apparatus

A new compressive testing apparatus is developed and used in this research. It has long gauge length to allow digital image correlation monitoring and anti buckling guides to prevent buckling. It allows the optical recording of strains and displacements. The novel setup is used to study the compressive response of tufted and untufted Carbon non crimp fabric composites with full field measurements. Experimental results show that the specimens are not bending in the apparatus under compression. Results also show reduced strain concentrations and a large strain field that provides a good environment for material compressive stiffness characterization. The test proves particularly successful for bias direction layup of [+45/-45] for which large damage mechanism occurs. However for [0/90] specimens a scatter in compressive ultimate strength was noticed which is due to the difficulty to prepare specimens with best minute accurate geometry. The compressive apparatus has shown to be a good alternative to existing setups and to provide significantly more information as well as having the possibility to be used in dynamics with a drop tower.

Fiber optic sensing and performance evaluation of a water conveyance tunnel with composite linings under super-high internal pressures

For long-distance water conveyance shield tunnels in operation,the high internal water pressure may cause excessive deformation of composite linings,affecting their structural integrity and serviceability.However,the deformation and failure characteristics of lining structures under internal water pressure are not well investigated in the literature,particularly for three-layer composite linings.This study presents an in situ experimental investigation on the response of two types of composite linings(i.e.separated and combined lining structures)subjected to internal pressures,in which a fiber optic nerve system(FONS)equipped with distributed strain and displacement sensing nerves was employed to monitor the performance of the two composite linings during testing.The experimental results clearly show that the damage of the tunnel lining under different internal pressures was mainly located in the self-compaction concrete layer.The separated lining structure responded more aggressively to the variations in internal pressures than the combined one.Moreover,two evaluation indices,i.e.radial displacement and effective stiffness coefficient,are proposed for describing the changes in the structural bearing performance.The effective stiffness coefficients of the two types of lining structures were reduced by 39.4%and 29.5%,respectively.Considering the convenience of field monitoring,it is suggested that the average strains at different layers can be used as characteristic parameters for estimating the health conditions of lining structures in service.The analysis results provide a practical reference for the design and health evaluation of water conveyance shield tunnels with composite linings.

Comparison between Double Crystals X-ray Diffraction and Micro-Raman Measurement on Composition Determination of High Ge Content Si_(1-x)Ge_(x) Layer Epitaxied on Si Substrate

It is important to acquire the composition of Si1-xGex layer, especially that with high Ge content, epitaxied on Si substrate. Two nondestructive examination methods, double crystals X-ray diffraction （DCXRD） and micro-Raman measurement, were introduced comparatively to determine x value in Si1-xGex layer, which show that while the two methods are consistent with each other when x is low, the results obtained from double crystals X-ray diffraction are not credible due to the large strain relaxation occurring in Si1-xGex layers when Ge content is higher than about 20%. Micro-Raman measurement is more appropriate for determining high Ge content than DCXRD.

Can composite performance measures predict survival of patients with colorectal cancer?

AIM: To assess the relationship between long-term colorectal patient survival and methods of calculating composite performance scores.METHODS: The Taiwan Cancer Database was used to identify patients who underwent bowel resection for colorectal adenocarcinoma between 2003 and 2004. Patients were assigned to one of three cohorts based on tumor staging: cohort 1, colon cancer stage < Ⅲ; cohort 2, colon cancer stage Ⅲ; cohort 3, rectal cancer. A composite performance score(CPS) was calculated for each patient using five different aggregating methods, including all-or-none, 70% standard, equal weight, analytic hierarchy process(AHP), and principal component analysis(PCA) algorithms. The relationships between CPS and five-year overall, disease-free, and disease-specific survivals were evaluated by a Cox proportional hazards model. A goodness-of-fit analysis for all five methods was performed using Akaike's information criterion.RESULTS: A total of 3272 colorectal cancer patients(cohort 1, 1164; cohort 2, 790; cohort 3, 1318 patients) with a mean age of 65 years were enrolled in the study. Bivariate correlation analysis showed that CPS values from the equal weight method were highly correlated with those from the AHP method in all cohorts(all P < 0.05). Multivariate Cox hazards analysis showed that CPS values derived from equal weight and AHP methods were significantly associated with fiveyear survivals of patients in cohorts 1 and 2(all P < 0.05). In these cohorts, higher CPS values suggested a higher probability of five-year survival. However, CPS values derived from the all-or-none method did not show any significant process-outcome relationship in any cohort. Goodness-of-fit analyses showed that CPS values derived from the PCA method were the best fit to the Cox proportional hazards model, whereas the values from the all-or-none model showed the poorest fit.CONCLUSION: CPS values may highlight process-outcome relationships for patients with colorectal cancer in addition to evaluating quality of care performance.

Simultaneous Measurements of Coal Ash Composition by Laser-induced Breakdown Spectroscopy in Different Optical Collection

针对燃煤组分分布不均匀的特性，研究不同收光模式对激光诱导击穿光谱技术同步测量灰成分的影响。选用具有不同灰成分含量梯度的燃煤样品作为检测对象，对比分析同向收光和侧向收光下灰成分组成元素谱线信号探测的强度和稳定性及SiO2、Al2O3、Fe2O3、CaO、MgO和TiO2含量定量分析的精确度。研究结果表明，相同实验条件下同向收光模式的光谱信号稳定性和定量分析精确度更好，检验样品中各灰成分的预测值和参考值之间的拟合度均在0．986以上。而侧向收光模式下探测到的光谱信号强度更强，光谱探测下限可以达到190nm。

Importance Measure Analysis for Use in Dynamic Performance Design of a Co-cured Composite Damping Instrument Panel

For the best dynamic performance of a co-cured composite damping instrument panel with light weight and high strength,a multilayer sandwich structure with polymethacrylimide( PMI) foam combined with embedded and co-cured composite damping structure is proposed. The structue can maintain the excellent mechanical properties of composite materials,and achieve the damping and light effect at the same time. Input variables which may affect the dynamic performance of the instrument panel were selected and variance based importance measure was analyzed through multifinite element method( FEM) analysis. Using the results of the importance measure analysis,with other design requirements,the important design variable was optimized and an instrument panel with the best dynamic performance under the requirements of light weight and high strength was obtained. The structure of the instrument panel can provide reference for the design of precision,high speed,and dynamic composite component. The importance measure analysis of dynamic performance of the instrument panel can provide a reference for relative design.

Polypyrrole Chitosan Cobalt Ferrite Nanoparticles Composite Layer for Measuring the Low Concentration of Fluorene Using Surface Plasmon Resonance

Fluorene is a polycyclic aromatic hydrocarbon, which is a hazardous toxic chemical in the environment. The measurement of low concentrations of fluorene is a subject of intense interest in chemistry and in the environment. Polypyrrole chitosan cobalt ferrite nanoparticles are prepared using the electrochemical method. The prepared layers are characterized using field emission scanning electron microscopy, Fourier transform infrared spectroscopy, and energy dispersive spectroscopy. The layers are used to detect fluorene using the surface plasmon resonance technique at room temperature. The composite layer is evaluated after detection of fluorene using atomic force microscopy. The fluorene is bound on the layer, and the shift of the resonance angle is about 0.0052°, corresponding to the limitation of 0.01 ppm.

Development of an automatic measurement system using atmospheric pressure photoionization ultrahigh-resolution mass spectrometry and application for on-line analysis of particulate matter

On-line chemical characterization of atmospheric particulate matter(PM)with soft ionization technique and ultrahigh-resolution Mass Spectrometry(UHRMS)provides molecular information of organic constituents in real time.Here we describe the development and application of an automatic measurement system that incorporates PM_(2.5)sampling,thermal desorption,atmospheric pressure photoionization,and UHRMS analysis.Molecular formulas of detected organic compounds were deducted from the accurate(±10 ppm)molecular weights obtained at a mass resolution of 100,000,allowing the identification of small organic compounds in PM_(2.5).Detection efficiencies of 28 standard compounds were determined and we found a high sensitivity and selectivity towards organic amines with limits of detection below 10 pg.As a proof of principle,PM_(2.5)samples collected off-line in winter in the urban area of Beijing were analyzed using the Ionization Module and HRMS of the system.The automatic system was then applied to conduct on-line measurements during the summer time at a time resolution of 2 hr.The detected organic compounds comprised mainly CHON and CHN compounds below 350 m/z.Pronounced seasonal variations in elemental composition were observed with shorter carbon backbones and higher O/C ratios in summer than that in winter.This result is consistent with stronger photochemical reactions and thus a higher oxidation state of organics in summer.Diurnal variation in signal intensity of each formula provides crucial information to reveal its source and formation pathway.In summary,the automatic measurement system serves as an important tool for the on-line characterization and identification of organic species in PM_(2.5).

Thrust Analysis of a Fish Robot Actuated by Piezoceramic Composite Actuators

In this work, a three-dimensional （3D） Computational Fluid Dynamics （CFD） model was built to simulate the tail fin motion of a fish robot actuated by a piezoceramic composite actuator, and to determine the maximum thrust tail-beat frequency. A simulation of the tail fin at a tail-beat frequency was performed to confirm measured thrust data from a previous study. The computed and measured thrusts were in good agreement. A series of thrust simulations were conducted for various tail-beat frequencies to confirm the maximum thrust frequency that was obtained from thrust measurements in the previous study. The largest thrust was calculated at a tail-beat frequency of 3.7 Hz and vortices around the tail were fully separated. The calculated maximum thrust tail-beat frequency was in good agreement with the measured frequency. Flow characteristics during tail fin motion were examined to explain why the largest thrust occurred at this particular tail-beat frequency.

Effects of dietary ratio of n-6 to n-3 polyunsaturated fatty acids on immunoglobulins, cytokines, fatty acid composition, and performance of lactating sows and suckling piglets

This experiment was conducted to investigate the effects of dietary ratios of n-6：n-3 polyunsaturated fatty acids （PUFA） on the performance of lactating sows and their piglets. Thirty pregnant Landrace sows were assigned to one of three treatments from d 108 of gestation until weaning （26-29 d） and were fed diets containing different ratios of n-6：n-3 PUFA including 3：1,9：1 and 13：1. The effects on sow and litter production traits were examined together with an assessment of sow body condition. No differences were detected among the treatments for the daily feed intake of sows or changes in sow weight and back-fat levels during lactation （P 〉 0.05）. Litter size at d 14 and d 21 were tended to increase in 3：1 treatment compared with 9：1 and 13：1 treatments （P 〈 0.10）. Litter weight gain （1.77 kg/d） from d 0 to d 14 was tended to increase in 9：1 groups compared with the other two treatments （P 〈 0.10）. A significant difference was observed for the content of a -linolenic acid, total n-3 PUFA, and the ratio of n-6：n-3 PUFA in the colostrum, milk, and piglets plasma （P 〈 0.01）. The effects of different ratios of n-6：n-3 PUFA in sow diets on colostrum, milk and piglet plasma immunoglobulin concentrations are studied. No difference was observed among treatments in the concentrations of IgM, and IgA in colostrum （P 〉 0.05）. A great significant difference for IgG concentration was observed among 3 group in colostrum. A great significant difference for IgA, and IgM （P〈 0.01） concentrations in piglet plasma at d14 and a significant difference for IgG（P 〈 0.05） was observed at d14. Furthermore, at d 21 of lactation, piglet plasma IgG and IgA concentration were greater in 3：1 compared with 13：1 group （P 〈 0.01）. In summary, the current study demonstrated that altering the ratio of n-6：n-3 PUFA in lactating sow diet had an effect on the immune component including immunoglobulin and cytokines, and it tended to increase the litter average daily gain and improve the immune status of piglets when dietary ratio of n-6：n-3 PUFA was 9：1.

Integrated Towing Transportation Technique for Offshore Wind Turbine with Composite Bucket Foundation

Composite bucket foundation and one-step installation technology for offshore wind turbine are the integration of foundation construction,transportation and whole installation at sea.The cost of offshore wind turbine construction and installation has been largely reduced.Foundation stability is the key technology in the process of towing transportation.Field observation data can reflect the real state of the foundation.In this paper,the influence of water depth and towing speed on liquid level,the compartment pressure,and the pitch angles during towing of composite bucket foundation are studied.These data are analyzed based on the field measurements data from a 3.3 MW offshore wind power project in China.The results show that with varied water depths and towing speeds,the compartment pressure changes are small during the bucket foundation towing process.The offshore wind turbine composite bucket foundation is stable while being towed in the ocean.

Sub-bandgap photocurrent response and carrier transport properties of undoped semi-insulating LEG GaAs as a composite

Undoped (ND) semi-insulating (SI) liquid encapsulated Czochralski (LEC) GaAscrystals were investigated by photocurrent and temperature-dependent Hall measurements. It isindicated that strong nonuniformities in the distributions of impurities and defects can occur forthe NDSILEC GaAs crystal grown under a condition with strong constitutional supercooling. In suchcase, the deep level that dominates Fermi level is spacial location dependent, and the GaAs crystalbecomes a composite consisting of a large number of elementary domains with differentconductivities. The sub-bandgap photocurrent response and the carrier transport properties for thiskind of composite are quite different from those for homogeneous NDSILEC GaAs.

Corrosion Resistance of Ni-P Composite Coating on Mg Alloy:Critical Role of the Intermediate Phosphate Conversion Coating Layer for Suppressing Galvanic Couple Formation

Electroless nickel(EN)plating can give rise to the severe galvanic corrosion of the magnesium(Mg)alloy matrix,owing to its nobler electrochemical potential than Mg alloy.To hinder the formation of galvanic couple,an intermediate phosphate conversion coating(PCC)layer is introduced between the EN layer and the Mg alloy matrix.Since the ceramic-like PCC layer cannot be catalyzed,a low-cost Ag-activation technique is used to process the PCC layer before electroless plating.The cross-section morphology and element distribution of the PCC-EN composite coating indicate that the PCC intermediate layer can effectively separate the Mg alloy from the EN layer.Moreover,the results of electrochemical tests suggest that the PCC-EN composite coating has a better corrosion resistance in comparison with the EN coating and AZ91D Mg alloy.

Facile fabrication of TiO_2 nanoparticle–TiO_2 nanofiber composites by co-electrospinning–electrospraying for dye-sensitized solar cells

We report a facile method for the fabrication of TiO2 nanofiber-nanoparticle composite （FP） via. simulta- neous electrospraying and electrospinning for dye-sensitized solar cell （DSC） applications. The loading of nanoparticles on the fibers is controlled by varying their feed rates during electrospinning. The FP composites having three different particle loading are prepared by the methodology and the FP with the highest particle loading （denoted as FP-3 in the manuscript） showed the best overall efficiency of 9.15% in comparison to the other compositions of the FP （FP-2, 8.15% and FP-1, Z51%, respectively） and nanofibers （F） and nanoparticles （P） separately （7.21 and 7.81, respectively）. All the material systems are characterized by spec- troscopy, microscopy, surface area measurements and the devices are characterized by current-voltage （I-V）, incident photon-to-current conversion efficiency （IPCE）, electrochemical impedance measurements, etc. I-V, dye-loading and reflectance measurements throw light on the overall performance of the DSC devices.