In this study,green zinc oxide(ZnO)/polypyrrole(Ppy)/cellulose acetate(CA)film has been synthesized via solvent casting.This film was used as supporting material for glucose oxidase(GOx)to sensitize a glucose biosenso...In this study,green zinc oxide(ZnO)/polypyrrole(Ppy)/cellulose acetate(CA)film has been synthesized via solvent casting.This film was used as supporting material for glucose oxidase(GOx)to sensitize a glucose biosensor.ZnO nanoparticles have been prepared via the green route using olive leaves extract as a reductant.ZnO/Ppy nanocomposite has been synthesized by a simple in-situ chemical oxidative polymerization of pyrrole(Py)monomer using ferric chloride(FeCl3)as an oxidizing agent.The produced materials and the composite films were characterized using X-ray diffraction analysis(XRD),scanning electron microscope(SEM),Fourier transform infrared(FTIR)and thermogravimetric analysis(TGA).Glucose oxidase was successfully immobilized on the surface of the prepared film and then ZnO/Ppy/CA/GOx composite was sputtered with platinum electrode for the current determination at different initial concentrations of glucose.Current measurements proved the suitability and the high sensitivity of the constructed biosensor for the detection of glucose levels in different samples.The performance of the prepared biosensor has been assessed by measuring and comparing glucose concentrations up to 800 ppm.The results affirmed the reliability of the developed biosensor towards real samples which suggests the wide-scale application of the proposed biosensor.展开更多
The goal is to develop a hybrid IPN network of polyvinyl acetate (PVAc) and ethylene-vinyl acetate (VAE). In this research work, the vinyl acetate (VAc)/ VAE hybrid emulsion and polyvinyl acetate emulsion (PVAc) were ...The goal is to develop a hybrid IPN network of polyvinyl acetate (PVAc) and ethylene-vinyl acetate (VAE). In this research work, the vinyl acetate (VAc)/ VAE hybrid emulsion and polyvinyl acetate emulsion (PVAc) were effectively synthesized. Emulsions with various characteristics have been developed by adjusting the weight ratios between the vinyl acetate monomer and the VAE component. The impacts on the mechanical, thermal, and physical properties of the films were investigated using tests for pencil hardness, tensile shear strength, pH, contact angle measurement, differential scanning calorimetry (DSC), and viscosity. When 5.0 weight percent VAE was added, the tensile shear strength in dry conditions decreased by 18.75% after a 24-hour bonding period, the heat resistance decreased by 26.29% (as per WATT 91) and the tensile shear strength decreased by approximately 36.52% in wet conditions (per EN 204). The pristine sample’s results were also confirmed by the contact angle test. The interpenetrating network (IPN) formation in hybrid PVAc emulsion as primary bonds does not directly attach to PVAc and VAE chains. The addition of VAE reduced the mechanical properties (at dry conditions) and heat resistance as per WATT 91. Contact angle analysis demonstrated that PVAc adhesives containing VAE had increased water resistance when compared to conventional PVA stabilised PVAc homopolymer-based adhesives. When compared to virgin PVAc Homo, the water resistance of the PVAc emulsion polymerization was enhanced by the addition of VAE.展开更多
Cellulose acetate butyrate(CAB)is a cellulose ester that is commonly used in applications such as coatings and leather brighteners.However,its appearance in a fibrous form is rarely reported.CAB porous micro/nanofibro...Cellulose acetate butyrate(CAB)is a cellulose ester that is commonly used in applications such as coatings and leather brighteners.However,its appearance in a fibrous form is rarely reported.CAB porous micro/nanofibrous membranes with a large number of nanopores on the fiber surface were successfully prepared by electrospinning with dichloromethane(DCM)/acetone(AC)as the mixed solvent.Apparent morphology,porosity,moisture permeability,air permeability,static water contact angles,and thermal conductivity of the fibrous membranes were investigated at different spinning voltages.The results showed that with the increase of the spinning voltage,the average fiber diameter of the CAB porous micro/nanofibrous membranes gradually decreased and the fiber diameter distribution was more uniform.When the spinning voltage reached 40 kV,the porosity reached 91.38%,the moisture permeability was up to 7430 g/(m^(2)·d),the air permeability was up to 36.289 mm/s,the static water contact angle was up to 145.0°,while the thermal conductivity of the fibrous membranes reached 0.030 W/(m·K).The material can be applied as thermal-insulation,waterproof and moisture-permeable membranes.展开更多
Original statement in Section 3.5:3.5.GB7 acetate reduced the mobility and invasion of HCT 116 cells The wound healing assay showed that GB7 acetate significantly decreased the migration area of HCT 116 cells when com...Original statement in Section 3.5:3.5.GB7 acetate reduced the mobility and invasion of HCT 116 cells The wound healing assay showed that GB7 acetate significantly decreased the migration area of HCT 116 cells when compared with the control group(P<0.05)(Figs.5A and B).Wound healing of 34%e43%was observed after 24 h and 48 h in untreated cancer cells,whereas 10%e21%were seen in the 100 and 150 mg/mL GB7 acetate groups.展开更多
Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the mo...Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive in highly moist conditions. Microcrystalline cellulose (MCC) are strong renewable, bio-based material and has great potential in a reinforcement of the polymeric matrix. Hence, the present work investigates the applicability of microcrystalline cellulose incorporated 3% and 5% in situ emulsion polymerization PVAc wood adhesives. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with different proportions of MCC were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was increased by increasing the concentration of MCC. The mechanical properties like tensile strength of adhesives with MCC were measured by universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that MCC can improve bonding strength as compared to PVAc Homo based adhesive in the wet condition which was validated through a contact angle study. The hardness of PVAc films were also changed positively by the addition of MCC. Here, we studied the effect of the addition of different concentrations of MCC materials in situ polymerization of PVAc on their performance properties.展开更多
The catalytic packing is the core component of the catalytic distillation,and how the catalyst exists in the packing has significant influence on the process.To investigate the effect of catalyst packings on the catal...The catalytic packing is the core component of the catalytic distillation,and how the catalyst exists in the packing has significant influence on the process.To investigate the effect of catalyst packings on the catalytic distillation process,the classical ethyl acetate reactive distillation system was utilized,and a supported catalytic packing(SCP)was prepared in comparison with the conventional tea-bag catalytic packing(TBP).Laboratory scale experiments showed that the ethyl acetate conversion of the SCP was superior to the TBP at a low catalyst loading.The effects of reaction kinetics,mass transfer performance and actual catalytic efficiency of the packings on this process were regarded as reasons and studied by combining the experiments and numerical simulation.Results suggested that the relatively immediate“in-situ separation”caused by the rapid reaction kinetics and better mass transfer performance of SCP may be a main reason for the difference of the conversion.展开更多
Polyamide 6 (PA6) was employed as a charring agent of intumescent flame retardant (IFR) to improve the flame retardancy of ethylene-vinyl acetate copolymer (EVA). Different processing procedures were used to regulate ...Polyamide 6 (PA6) was employed as a charring agent of intumescent flame retardant (IFR) to improve the flame retardancy of ethylene-vinyl acetate copolymer (EVA). Different processing procedures were used to regulate the localization of IFR in the EVA matrix. Localizations in which IFR was dispersed in the PA6phase or in the EVA phase were prepared. The effect of the localization of IFR on the flame retardancy of EVA was investigated. The limited oxygen index (LOI), vertical burning (UL 94) and cone calorimeter test (CCT)showed that the localization of IFR in the EVA matrix exhibited a remarkable influence on the flame retardancy.Compared with EVA/IFR, a weak improvement in the flame retardancy was observed in the EVA/PA6/IFR blend withthe localization of IFR in the PA6 phase. When IFR was regulated from the PA6 phase to the EVA matrix,a remarkable increase in the flame retardancy was exhibited. The LOI was increased from 27.8%to 32.7%, and the UL 94 vertical rating was increased from V-2 to V-0. Moreover, an approximately 41.36%decrease in the peak heat release rate was exhibited. A continuous and compact intumescent charring layer that formed in the blends with the localization of IFR in the EVA matrix should be responsible for its excellent flame retardancy.展开更多
The sweet potato weevil(Cylas formicarius(Fab.)(Coleoptera: Brentidae)) is a pest that feeds on sweet potato(Ipomoea batatas(L.) Lam.(Solanales: Convolvulaceae)), causing substantial economic losses annually. However,...The sweet potato weevil(Cylas formicarius(Fab.)(Coleoptera: Brentidae)) is a pest that feeds on sweet potato(Ipomoea batatas(L.) Lam.(Solanales: Convolvulaceae)), causing substantial economic losses annually. However, no safe and effective methods have been found to protect sweet potato from this pest. Herbivore-induced plant volatiles(HIPVs)promote various defensive bioactivities, but their formation and the defense mechanisms in sweet potato have not been investigated. To identify the defensive HIPVs in sweet potato, the release dynamics of volatiles was monitored.The biosynthetic pathways and regulatory factors of the candidate HIPVs were revealed via stable isotope tracing and analyses at the transcriptional and metabolic levels. Finally, the anti-insect activities and the defense mechanisms of the gaseous candidates were evaluated. The production of(Z)-3-hexenyl acetate(z3HAC) and allo-ocimene was induced by sweet potato weevil feeding, with a distinct circadian rhythm. Ipomoea batatas ocimene synthase(IbOS) is first reported here as a key gene in allo-ocimene synthesis. Insect-induced wounding promoted the production of the substrate,(Z)-3-hexenol, and upregulated the expression of IbOS, which resulted in higher contents of z3HAC and allo-ocimene,respectively. Gaseous z3HAC and allo-ocimene primed nearby plants to defend themselves against sweet potato weevils. These results provide important data regarding the formation, regulation, and signal transduction mechanisms of defensive volatiles in sweet potato, with potential implications for improving sweet potato weevil management strategies.展开更多
Polyvinyl alcohol (PVA) stabilized Polyvinyl acetate (PVAc) dispersions-based wood adhesive has poor water and heat resistance. Recently, the addition of fillers in the wood adhesive is one of the most effective ways ...Polyvinyl alcohol (PVA) stabilized Polyvinyl acetate (PVAc) dispersions-based wood adhesive has poor water and heat resistance. Recently, the addition of fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive. Inorganic fillers have unique characteristics to improve the performance of adhesive, such as small size, high surface energy and surface hardness. Hence, the present work investigates the applicability of calcium carbonate and clay incorporated 3% in situ emulsion polymerization PVAc wood adhesive. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with 3% calcium carbonate and 3% clay were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was reduced in the case of the addition of calcium carbonate and increased in the case of clay. The mechanical properties like tensile strength of adhesives with calcium carbonate and clay were measured by a universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that clay can improve bonding strength as compared to calcium carbonate of PVAc adhesive in wet conditions. The hardness of PVAc films was also changed positively by the addition of calcium carbonate and clay. Thermal stability of PVAc was significantly improved as calcium carbonate and clay were added to PVAc. Here, we did a comparative study of the effect of the addition of calcium carbonate and clay filler materials in situ polymerization of PVAc on their different properties.展开更多
The“shuttle effect”of polysulfides hampers the commercialization of lithium-sulfur(Li-S)batteries.Here,a thin molecular sieve film was decorated on the surface of an electrospun cellulose acetate(CA)membrane derived...The“shuttle effect”of polysulfides hampers the commercialization of lithium-sulfur(Li-S)batteries.Here,a thin molecular sieve film was decorated on the surface of an electrospun cellulose acetate(CA)membrane derived from recycled cigarette filters,where the truncated cone structureβ-cyclodextrin(β-CD)was selected as the building block to physically block and chemically trap polysulfides while simultaneously dramatically speeding up ion transport.Furthermore,on theβ-CD free side of the separator facing the cathode,graphite carbon(C)was sputtered as an upper current collector,which barely increases the thickness.These benefits result in an initial discharge performance of 1378.24 mAh g^(−1) and long-term cycling stability of 863.78 mAh g^(−1) after 1000 cycles at 0.2 C for the battery with theβ-CD/CA/C separator,which is more than three times that of the PP separator after 500 cycles.Surprisingly,the funnel-type channel ofβ-CD generates a differential ionic fluid pressure on both sides,speeding up ion transport by up to 69%,and a 65.3%faster charging rate of 9484 mA g^(−1) was achieved.The“funnel effect”of a separator is regarded as a novel and high-efficiency solution for fast charging of Li-S and other lithium secondary batteries.展开更多
This study aims to explore the formation mechanism of ethyl acetate and organic acids in acid rice soup(rice-acid soup)inoculated with Kluyveromyces marxianus L1-1 through the complementary analysis of transcriptome a...This study aims to explore the formation mechanism of ethyl acetate and organic acids in acid rice soup(rice-acid soup)inoculated with Kluyveromyces marxianus L1-1 through the complementary analysis of transcriptome and proteome.The quantity of K.marxianus L1-1 varied significantly in the fermentation process of rice-acid soup and the first and third days were the two key turning points in the growth phase of K.marxianus L1-1.Importantly,the concentrations of ethyl acetate,ethanol,acetic acid,and L-lactic acid increased from day 1 to day 3.At least 4231 genes and 2937 proteins were identified and 610 differentially expressed proteins were annotated to 30 Kyoto Encyclopedia of Genes and Genomes(KEGG)pathways based on the analysis results of transcriptome and proteome.The key genes and proteins including up-regulated alcohol dehydrogenase family,alcohol O-acetyltransferase,acetyl-CoA C-acetyltransferase,acyl-coenzyme A thioester hydrolase,and down-regulated aldehyde dehydrogenase family were involved in glycolysis/gluconeogenesis pathways,starch and sucrose metabolism pathways,amino sugar and nucleotide sugar metabolism pathways,tricarboxylic acid(TCA)cycle,and pyruvate metabolism pathways,thus promoting the formation of ethyl acetate,organic acids,alcohols,and other esters.Our results revealed the formation mechanisms of ethyl acetate and organic acids in rice-acid soup inoculated with K.marxianus L1-1.展开更多
This paper addressed the efect of copper acetate on the combustion characteristics of anthracite depending on the fractional composition of fuel and additive introduction method.Anthracite was impregnated with 5 wt%of...This paper addressed the efect of copper acetate on the combustion characteristics of anthracite depending on the fractional composition of fuel and additive introduction method.Anthracite was impregnated with 5 wt%of Cu(CH_(3)COO)_(2)by mechanical mixing and incipient wetness impregnation.Four anthracite samples of diferent fraction with d<0.1 mm,d=0.1-0.5 mm,d=0.5-1.0 mm,and d=1.0-2.0 mm were compared.According to EDX mapping,incipient wetness impregnation provides a higher dispersion of the additive and its uniform distribution in the sample.The ignition and combustion characteristics of the modifed anthracite samples were studied by thermal analysis and high-speed video recording of the processes in a combustion chamber(at heating medium temperature of 800℃).It was found that copper acetate increases anthracite reactivity,which was evidenced by decreased onset temperature of combustion(ΔT_(i))by 35-190℃and reduced ignition delay time(Δτ_(i))by 2.1-5.4 s.Copper acetate reduces fuel underburning(on average by 70%)in the ash residue of anthracite and decreases the amount of CO and NO_(x)in gas-phase products(on average by 18.5%and 20.8%,respectively).The mechanism for activation of anthracite combustion by copper acetate is proposed.展开更多
Objective:To observe the clinical efficacy of different dosage forms of lepraline acetate(LA)in the treatment of girls with central precocious puberty(CPP).Methods:72 CPP girls treated in the Department of Pediatrics ...Objective:To observe the clinical efficacy of different dosage forms of lepraline acetate(LA)in the treatment of girls with central precocious puberty(CPP).Methods:72 CPP girls treated in the Department of Pediatrics of Huai'an First People's Hospital from February 2021 to August 2022 were included as subjects and divided into two groups:3-month LA group(n=34)and 1-month LA group(n=38).Both group girls were treated for 6 months.Serum hormone levels,body mass index(BMI),bone age/chronological age(BA/CA)and pelvic color ultrasound were detected at 0 and 6 months after treatment,and the changes of various indexes were compared before and after treatment.Results:1)There were no significant differences in baseline data between the two groups before treatment(P>0.05).2)After 6 months of treatment,BA/CA decreased,growth rate slowed down,and predicted adult height increased in both groups(P<0.05),but there were no significant differences between groups(P>0.05).3)After 6 months of treatment,there waere no significant differences in luteinizing hormone(LH)inhibition ratio between the 3 month and 1 month dosage groups(P>0.05).After treatment,the peak value of serum LH and FSH,estradiol level,uterine volume,bilateral ovarian volume,maximum follicle diameter and the number of follicles 4mm were significantly decreased in the two groups,but there were no significant differences between the two groups(P>0.05).4)There were no significant differences in the levels of thyroid hormone,fasting blood glucose and triglyceride between the two groups before and after treatment(P>0.05).Total cholesterol levels were increased after treatment(P<0.05),but there was no significant difference between groups(P>0.05).5)No serious adverse reactions occurred during the treatment of the two dosage forms of LA,but the 3-month dosage form of LA reduced the treatment cost and improved the treatment compliance.Conclusion:The short-term efficacy of 3-month LA in the treatment of CPP in girls is similar to that of 1-month LA.The 3-month dosage form LA is a safe,effective,and economical method for the treatment of CPP in girls.展开更多
The sergestid shrimp Acetes vulgaris has long been an important fishery species in estuaries and coastal waters along the Pang-Rad River, Rayong province, Thailand. In nature, this shrimp feeds on a wide range of food...The sergestid shrimp Acetes vulgaris has long been an important fishery species in estuaries and coastal waters along the Pang-Rad River, Rayong province, Thailand. In nature, this shrimp feeds on a wide range of food items, such as phytoplankton, zooplankton, algae, plant matter, debris, sand, and mud. The objective of this study was to compare different feeds on growth and survival of A. vulgaris reared in fiberglass tanks containing 70 m<sup>3</sup> of seawater salinity 25 ppt over a period of 70 days. Individual shrimps were fed with four different types of feeds i.e., newly hatched Artemia (Ar), rotifer (Ro), newly hatched Artemia + rotifer (ArRo) and shrimp larvae commercial feed (SF). Results suggested that specific growth rates (both for body weight and body length) of shrimps reared with SF were not significantly different with treatment feed with Ar, ArRo and Ro (p ≥ 0.05). The survival rate of A. vulgaris did not vary significantly (p ≥ 0.05) among the Ar, Ro and ArRo treatments. However, the highest survival rate of shrimp (81.78% ± 3.08%) was observed in SF treatment and the percentage of survival rate was significantly different with treatment feed with Ar, Ro and ArRo (p ≤ 0.05). The findings reflected the ability of Acetes shrimps to consume diverse food types including both live feed and pelleted feed. Insights obtained from this research suggested that artificial feed can be as efficient as live feeds. This new knowledge is a needed addition to a currently lacking knowledge base for aquaculture of this Acetes species.展开更多
Objective:To analyze the clinical efficacy of megestrol acetate dispersible tablets in the adjuvant treatment of acute leukemia.Methods:80 patients with acute leukemia admitted from December 2021 to December 2022 were...Objective:To analyze the clinical efficacy of megestrol acetate dispersible tablets in the adjuvant treatment of acute leukemia.Methods:80 patients with acute leukemia admitted from December 2021 to December 2022 were randomly divided into two groups.The control group underwent chemotherapy,and the observation group took megestrol acetate dispersible tablets and underwent chemotherapy.The effect of the treatments were evaluated by analyzing the albumin(Alb)and prealbumin(Palb)indicators,and the adverse reactions were observed.Results:There was no significant difference in Alb and Palb indexes between the two groups before treatment(P>0.05).After treatment,Alb and Palb indexes in the observation group were greater than those in the control group(P<0.05).The incidence of adverse reactions in the control group was 20.00%,which was significantly higher than the observation group(5.00%),with P<0.05.Conclusion:The combination of megestrol acetate dispersible tablets and chemotherapy is more effective in treating patients with acute leukemia,and the Alb and Palb indexes can be optimized.Besides,there are fewer adverse reactions,which means that the treatment is relatively safe.展开更多
BACKGROUND Conventional magnifying endoscopy with narrow-band imaging(NBI)observation of the gastric body mucosa shows dominant patterns in relation to the regular arrangement of collecting venules,subepithelial capil...BACKGROUND Conventional magnifying endoscopy with narrow-band imaging(NBI)observation of the gastric body mucosa shows dominant patterns in relation to the regular arrangement of collecting venules,subepithelial capillary network,and gastric pits.AIM To evaluate the effectiveness of a new one-dual(near)focus,NBI mode in the assessment of the microscopic features of gastric body mucosa compared to conventional magnification.METHODS During 2021 and 2022,68 patients underwent proximal gastrointestinal endoscopy using magnification endoscopic modalities subsequently applying acetic acid(AA).The GIF-190HQ series NBI system with dual focus capability was used for the investigation of gastric mucosa.At the time of the endoscopy,the gastric body mucosa of all enrolled patients was photographed using the white light endoscopy(WLE),near focus(NF),NF-NBI,AA-NF,and AA-NF-NBI modes.RESULTS The WLE,NF and NF-NBI endoscopic modes for all patients(204 images)were classified in the same order into three groups.Two images from each patient for the AA-NF and AA-NF-NBI endoscopic modes were classified in the same order.According to all three observers who completed the work independently,NF magnification was significantly superior to WLE(P<0.01),and the NF-NBI mode was significantly superior to NF magnification(P<0.01).After applying AA,the three observers confirmed that AA-NF-NBI was significantly superior to AA-NF(P<0.01).Interobserver kappa values for WLE were 0.609,0.704,and 0.598,respectively and were 0.600,0.721,and 0.637,respectively,for NF magnification.For the NF-NBI mode,the values were 0.378,0.471,and 0.553,respectively.For AA-NF,they were 0.453,0.603,and 0.480,respectively,and for AA-NF-NBI,they were 0.643,0.506,and 0.354,respectively.CONCLUSION When investigating gastric mucosa in microscopic detail,NF-NBI was the most powerful endoscopic mode for assessing regular arrangement of collecting venules,subepithelial capillary network,and gastric pits among the five endoscopic modalities investigated in this study.AA-NF-NBI was the most powerful endoscopic mode for analyzing crypt opening and intervening part.展开更多
Mg-air batteries have attracted tremendous attention as a potential next-generation power source for portable electronics and e-transportation due to their remarkable high theoretical volumetric energy density,environ...Mg-air batteries have attracted tremendous attention as a potential next-generation power source for portable electronics and e-transportation due to their remarkable high theoretical volumetric energy density,environmental sustainability,and cost-effectiveness.However,the fast hydrogen evolution reaction(HER)in NaCl-based aqueous electrolytes impairs the performance of Mg-air batteries and leads to poor specific capacity,low energy density,and low utilization.Thus,the conventionally used NaCl solute was proposed to be replaced by NaNO_(3)and acetic acid additive as a corrosion inhibitor,therefore an electrolyte engineering for long-life time Mg-air batteries is reported.The resulting Mg-air batteries based on this optimized electrolyte demonstrate an improved discharge voltage reaching~1.8 V for initial 5 h at a current density of 0.5 mA/cm^(2) and significantly prolonged cells'operational lifetime to over 360 h,in contrast to only~17 h observed in NaCl electrolyte.X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry were employed to analyse the composition of surface film and scanning electron microscopy combined with transmission electron microscopy to clarify the morphology changes of the surface layer as a function of acetic acid addition.The thorough studies of chemical composition and morphology of corrosion products have allowed us to elucidate the working mechanism of Mg anode in this optimized electrolyte for Mg-air batteries.展开更多
It was reported that hemispheric corrosion occurred in copper tubes in an acetic acid environment. When hemispheric corrosion occurred, corrosion could easily progress if water then flowed into the copper pipe, and co...It was reported that hemispheric corrosion occurred in copper tubes in an acetic acid environment. When hemispheric corrosion occurred, corrosion could easily progress if water then flowed into the copper pipe, and countermeasures were needed. Therefore, we studied the copper corrosion caused by acetic acid. The present work investigated the relationship between the corrosion form of copper and acetic acid concentration using phosphorous-deoxidized copper, and reported that hemispherical corrosion was observed at acetic acid concentrations of 0.01 to 1 vol.% (0.002 to 0.2 mol·L<sup>-1</sup>) in the immersion test. In this study, the effects of acetic acid and phosphate on copper corrosion were examined using oxygen-free copper in immersion tests. The results suggested that different concentrations of phosphate in acetic acid solutions and the presence or absence of acetic acid and phosphate affected the corrosion of copper, resulting in different corrosion forms and corrosion progress.展开更多
文摘In this study,green zinc oxide(ZnO)/polypyrrole(Ppy)/cellulose acetate(CA)film has been synthesized via solvent casting.This film was used as supporting material for glucose oxidase(GOx)to sensitize a glucose biosensor.ZnO nanoparticles have been prepared via the green route using olive leaves extract as a reductant.ZnO/Ppy nanocomposite has been synthesized by a simple in-situ chemical oxidative polymerization of pyrrole(Py)monomer using ferric chloride(FeCl3)as an oxidizing agent.The produced materials and the composite films were characterized using X-ray diffraction analysis(XRD),scanning electron microscope(SEM),Fourier transform infrared(FTIR)and thermogravimetric analysis(TGA).Glucose oxidase was successfully immobilized on the surface of the prepared film and then ZnO/Ppy/CA/GOx composite was sputtered with platinum electrode for the current determination at different initial concentrations of glucose.Current measurements proved the suitability and the high sensitivity of the constructed biosensor for the detection of glucose levels in different samples.The performance of the prepared biosensor has been assessed by measuring and comparing glucose concentrations up to 800 ppm.The results affirmed the reliability of the developed biosensor towards real samples which suggests the wide-scale application of the proposed biosensor.
文摘The goal is to develop a hybrid IPN network of polyvinyl acetate (PVAc) and ethylene-vinyl acetate (VAE). In this research work, the vinyl acetate (VAc)/ VAE hybrid emulsion and polyvinyl acetate emulsion (PVAc) were effectively synthesized. Emulsions with various characteristics have been developed by adjusting the weight ratios between the vinyl acetate monomer and the VAE component. The impacts on the mechanical, thermal, and physical properties of the films were investigated using tests for pencil hardness, tensile shear strength, pH, contact angle measurement, differential scanning calorimetry (DSC), and viscosity. When 5.0 weight percent VAE was added, the tensile shear strength in dry conditions decreased by 18.75% after a 24-hour bonding period, the heat resistance decreased by 26.29% (as per WATT 91) and the tensile shear strength decreased by approximately 36.52% in wet conditions (per EN 204). The pristine sample’s results were also confirmed by the contact angle test. The interpenetrating network (IPN) formation in hybrid PVAc emulsion as primary bonds does not directly attach to PVAc and VAE chains. The addition of VAE reduced the mechanical properties (at dry conditions) and heat resistance as per WATT 91. Contact angle analysis demonstrated that PVAc adhesives containing VAE had increased water resistance when compared to conventional PVA stabilised PVAc homopolymer-based adhesives. When compared to virgin PVAc Homo, the water resistance of the PVAc emulsion polymerization was enhanced by the addition of VAE.
基金National Natural Science Foundation of China(No.52203056)。
文摘Cellulose acetate butyrate(CAB)is a cellulose ester that is commonly used in applications such as coatings and leather brighteners.However,its appearance in a fibrous form is rarely reported.CAB porous micro/nanofibrous membranes with a large number of nanopores on the fiber surface were successfully prepared by electrospinning with dichloromethane(DCM)/acetone(AC)as the mixed solvent.Apparent morphology,porosity,moisture permeability,air permeability,static water contact angles,and thermal conductivity of the fibrous membranes were investigated at different spinning voltages.The results showed that with the increase of the spinning voltage,the average fiber diameter of the CAB porous micro/nanofibrous membranes gradually decreased and the fiber diameter distribution was more uniform.When the spinning voltage reached 40 kV,the porosity reached 91.38%,the moisture permeability was up to 7430 g/(m^(2)·d),the air permeability was up to 36.289 mm/s,the static water contact angle was up to 145.0°,while the thermal conductivity of the fibrous membranes reached 0.030 W/(m·K).The material can be applied as thermal-insulation,waterproof and moisture-permeable membranes.
文摘Original statement in Section 3.5:3.5.GB7 acetate reduced the mobility and invasion of HCT 116 cells The wound healing assay showed that GB7 acetate significantly decreased the migration area of HCT 116 cells when compared with the control group(P<0.05)(Figs.5A and B).Wound healing of 34%e43%was observed after 24 h and 48 h in untreated cancer cells,whereas 10%e21%were seen in the 100 and 150 mg/mL GB7 acetate groups.
文摘Polyvinyl alcohol (PVA) colloid stabilized Polyvinyl acetate (PVAc) based wood adhesive has poor performance in highly humid conditions. Currently, the addition of natural fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive in highly moist conditions. Microcrystalline cellulose (MCC) are strong renewable, bio-based material and has great potential in a reinforcement of the polymeric matrix. Hence, the present work investigates the applicability of microcrystalline cellulose incorporated 3% and 5% in situ emulsion polymerization PVAc wood adhesives. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with different proportions of MCC were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was increased by increasing the concentration of MCC. The mechanical properties like tensile strength of adhesives with MCC were measured by universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that MCC can improve bonding strength as compared to PVAc Homo based adhesive in the wet condition which was validated through a contact angle study. The hardness of PVAc films were also changed positively by the addition of MCC. Here, we studied the effect of the addition of different concentrations of MCC materials in situ polymerization of PVAc on their performance properties.
基金support provided by National Natural Science Foundation of China(21978243).
文摘The catalytic packing is the core component of the catalytic distillation,and how the catalyst exists in the packing has significant influence on the process.To investigate the effect of catalyst packings on the catalytic distillation process,the classical ethyl acetate reactive distillation system was utilized,and a supported catalytic packing(SCP)was prepared in comparison with the conventional tea-bag catalytic packing(TBP).Laboratory scale experiments showed that the ethyl acetate conversion of the SCP was superior to the TBP at a low catalyst loading.The effects of reaction kinetics,mass transfer performance and actual catalytic efficiency of the packings on this process were regarded as reasons and studied by combining the experiments and numerical simulation.Results suggested that the relatively immediate“in-situ separation”caused by the rapid reaction kinetics and better mass transfer performance of SCP may be a main reason for the difference of the conversion.
基金the National Natural Science Foundation of China (No.51673059)the Science and Technology Planning Project of Henan Province (No. 212102210636)the Opening Project of Jiangxi Province Key Laboratory of Polymer Micro/Nano Manufacturing and Devices (East China University of Technology)。
文摘Polyamide 6 (PA6) was employed as a charring agent of intumescent flame retardant (IFR) to improve the flame retardancy of ethylene-vinyl acetate copolymer (EVA). Different processing procedures were used to regulate the localization of IFR in the EVA matrix. Localizations in which IFR was dispersed in the PA6phase or in the EVA phase were prepared. The effect of the localization of IFR on the flame retardancy of EVA was investigated. The limited oxygen index (LOI), vertical burning (UL 94) and cone calorimeter test (CCT)showed that the localization of IFR in the EVA matrix exhibited a remarkable influence on the flame retardancy.Compared with EVA/IFR, a weak improvement in the flame retardancy was observed in the EVA/PA6/IFR blend withthe localization of IFR in the PA6 phase. When IFR was regulated from the PA6 phase to the EVA matrix,a remarkable increase in the flame retardancy was exhibited. The LOI was increased from 27.8%to 32.7%, and the UL 94 vertical rating was increased from V-2 to V-0. Moreover, an approximately 41.36%decrease in the peak heat release rate was exhibited. A continuous and compact intumescent charring layer that formed in the blends with the localization of IFR in the EVA matrix should be responsible for its excellent flame retardancy.
基金supported by the National Natural Science Foundation of China–Guangdong Natural Science Foundation Joint Project (U1701234)。
文摘The sweet potato weevil(Cylas formicarius(Fab.)(Coleoptera: Brentidae)) is a pest that feeds on sweet potato(Ipomoea batatas(L.) Lam.(Solanales: Convolvulaceae)), causing substantial economic losses annually. However, no safe and effective methods have been found to protect sweet potato from this pest. Herbivore-induced plant volatiles(HIPVs)promote various defensive bioactivities, but their formation and the defense mechanisms in sweet potato have not been investigated. To identify the defensive HIPVs in sweet potato, the release dynamics of volatiles was monitored.The biosynthetic pathways and regulatory factors of the candidate HIPVs were revealed via stable isotope tracing and analyses at the transcriptional and metabolic levels. Finally, the anti-insect activities and the defense mechanisms of the gaseous candidates were evaluated. The production of(Z)-3-hexenyl acetate(z3HAC) and allo-ocimene was induced by sweet potato weevil feeding, with a distinct circadian rhythm. Ipomoea batatas ocimene synthase(IbOS) is first reported here as a key gene in allo-ocimene synthesis. Insect-induced wounding promoted the production of the substrate,(Z)-3-hexenol, and upregulated the expression of IbOS, which resulted in higher contents of z3HAC and allo-ocimene,respectively. Gaseous z3HAC and allo-ocimene primed nearby plants to defend themselves against sweet potato weevils. These results provide important data regarding the formation, regulation, and signal transduction mechanisms of defensive volatiles in sweet potato, with potential implications for improving sweet potato weevil management strategies.
文摘Polyvinyl alcohol (PVA) stabilized Polyvinyl acetate (PVAc) dispersions-based wood adhesive has poor water and heat resistance. Recently, the addition of fillers in the wood adhesive is one of the most effective ways to enhance the performance of PVAc wood adhesive. Inorganic fillers have unique characteristics to improve the performance of adhesive, such as small size, high surface energy and surface hardness. Hence, the present work investigates the applicability of calcium carbonate and clay incorporated 3% in situ emulsion polymerization PVAc wood adhesive. Effect on physical, thermal and mechanical properties was studied by viscosity, pH, contact angle measurement, differential scanning calorimetry (DSC) and pencil hardness test of films. Emulsions with 3% calcium carbonate and 3% clay were prepared and the shear strength of the applied adhesive on wood was measured. The viscosity of the adhesives was reduced in the case of the addition of calcium carbonate and increased in the case of clay. The mechanical properties like tensile strength of adhesives with calcium carbonate and clay were measured by a universal tensile machine (UTM). Thermal stability was studied by differential scanning calorimetry (DSC). The tensile shear strength demonstrates that clay can improve bonding strength as compared to calcium carbonate of PVAc adhesive in wet conditions. The hardness of PVAc films was also changed positively by the addition of calcium carbonate and clay. Thermal stability of PVAc was significantly improved as calcium carbonate and clay were added to PVAc. Here, we did a comparative study of the effect of the addition of calcium carbonate and clay filler materials in situ polymerization of PVAc on their different properties.
基金the Jiangsu Provincial Key Research and Development Program(BE2017060)the China Postdoctoral Science Foundation(169483)the 111 Project(B17021)。
文摘The“shuttle effect”of polysulfides hampers the commercialization of lithium-sulfur(Li-S)batteries.Here,a thin molecular sieve film was decorated on the surface of an electrospun cellulose acetate(CA)membrane derived from recycled cigarette filters,where the truncated cone structureβ-cyclodextrin(β-CD)was selected as the building block to physically block and chemically trap polysulfides while simultaneously dramatically speeding up ion transport.Furthermore,on theβ-CD free side of the separator facing the cathode,graphite carbon(C)was sputtered as an upper current collector,which barely increases the thickness.These benefits result in an initial discharge performance of 1378.24 mAh g^(−1) and long-term cycling stability of 863.78 mAh g^(−1) after 1000 cycles at 0.2 C for the battery with theβ-CD/CA/C separator,which is more than three times that of the PP separator after 500 cycles.Surprisingly,the funnel-type channel ofβ-CD generates a differential ionic fluid pressure on both sides,speeding up ion transport by up to 69%,and a 65.3%faster charging rate of 9484 mA g^(−1) was achieved.The“funnel effect”of a separator is regarded as a novel and high-efficiency solution for fast charging of Li-S and other lithium secondary batteries.
基金financially supported by National Natural Science Foundation of China (32060530)Guizhou University, Gui Da Te Gang He Zi (2022) 39, Technology platform and talent team plan of Guizhou. China ((2018)5251)+2 种基金Graduate Research Fund Project of Guizhou (YJSCXJH(2019]028)Industry-University-Research Cooperation Project of Guizhou (701/700465172217)China Scholarship Council (201906670006)
文摘This study aims to explore the formation mechanism of ethyl acetate and organic acids in acid rice soup(rice-acid soup)inoculated with Kluyveromyces marxianus L1-1 through the complementary analysis of transcriptome and proteome.The quantity of K.marxianus L1-1 varied significantly in the fermentation process of rice-acid soup and the first and third days were the two key turning points in the growth phase of K.marxianus L1-1.Importantly,the concentrations of ethyl acetate,ethanol,acetic acid,and L-lactic acid increased from day 1 to day 3.At least 4231 genes and 2937 proteins were identified and 610 differentially expressed proteins were annotated to 30 Kyoto Encyclopedia of Genes and Genomes(KEGG)pathways based on the analysis results of transcriptome and proteome.The key genes and proteins including up-regulated alcohol dehydrogenase family,alcohol O-acetyltransferase,acetyl-CoA C-acetyltransferase,acyl-coenzyme A thioester hydrolase,and down-regulated aldehyde dehydrogenase family were involved in glycolysis/gluconeogenesis pathways,starch and sucrose metabolism pathways,amino sugar and nucleotide sugar metabolism pathways,tricarboxylic acid(TCA)cycle,and pyruvate metabolism pathways,thus promoting the formation of ethyl acetate,organic acids,alcohols,and other esters.Our results revealed the formation mechanisms of ethyl acetate and organic acids in rice-acid soup inoculated with K.marxianus L1-1.
文摘This paper addressed the efect of copper acetate on the combustion characteristics of anthracite depending on the fractional composition of fuel and additive introduction method.Anthracite was impregnated with 5 wt%of Cu(CH_(3)COO)_(2)by mechanical mixing and incipient wetness impregnation.Four anthracite samples of diferent fraction with d<0.1 mm,d=0.1-0.5 mm,d=0.5-1.0 mm,and d=1.0-2.0 mm were compared.According to EDX mapping,incipient wetness impregnation provides a higher dispersion of the additive and its uniform distribution in the sample.The ignition and combustion characteristics of the modifed anthracite samples were studied by thermal analysis and high-speed video recording of the processes in a combustion chamber(at heating medium temperature of 800℃).It was found that copper acetate increases anthracite reactivity,which was evidenced by decreased onset temperature of combustion(ΔT_(i))by 35-190℃and reduced ignition delay time(Δτ_(i))by 2.1-5.4 s.Copper acetate reduces fuel underburning(on average by 70%)in the ash residue of anthracite and decreases the amount of CO and NO_(x)in gas-phase products(on average by 18.5%and 20.8%,respectively).The mechanism for activation of anthracite combustion by copper acetate is proposed.
基金Jiangsu Province Maternal and Child Health Care Project (No.FYX202213)。
文摘Objective:To observe the clinical efficacy of different dosage forms of lepraline acetate(LA)in the treatment of girls with central precocious puberty(CPP).Methods:72 CPP girls treated in the Department of Pediatrics of Huai'an First People's Hospital from February 2021 to August 2022 were included as subjects and divided into two groups:3-month LA group(n=34)and 1-month LA group(n=38).Both group girls were treated for 6 months.Serum hormone levels,body mass index(BMI),bone age/chronological age(BA/CA)and pelvic color ultrasound were detected at 0 and 6 months after treatment,and the changes of various indexes were compared before and after treatment.Results:1)There were no significant differences in baseline data between the two groups before treatment(P>0.05).2)After 6 months of treatment,BA/CA decreased,growth rate slowed down,and predicted adult height increased in both groups(P<0.05),but there were no significant differences between groups(P>0.05).3)After 6 months of treatment,there waere no significant differences in luteinizing hormone(LH)inhibition ratio between the 3 month and 1 month dosage groups(P>0.05).After treatment,the peak value of serum LH and FSH,estradiol level,uterine volume,bilateral ovarian volume,maximum follicle diameter and the number of follicles 4mm were significantly decreased in the two groups,but there were no significant differences between the two groups(P>0.05).4)There were no significant differences in the levels of thyroid hormone,fasting blood glucose and triglyceride between the two groups before and after treatment(P>0.05).Total cholesterol levels were increased after treatment(P<0.05),but there was no significant difference between groups(P>0.05).5)No serious adverse reactions occurred during the treatment of the two dosage forms of LA,but the 3-month dosage form of LA reduced the treatment cost and improved the treatment compliance.Conclusion:The short-term efficacy of 3-month LA in the treatment of CPP in girls is similar to that of 1-month LA.The 3-month dosage form LA is a safe,effective,and economical method for the treatment of CPP in girls.
文摘The sergestid shrimp Acetes vulgaris has long been an important fishery species in estuaries and coastal waters along the Pang-Rad River, Rayong province, Thailand. In nature, this shrimp feeds on a wide range of food items, such as phytoplankton, zooplankton, algae, plant matter, debris, sand, and mud. The objective of this study was to compare different feeds on growth and survival of A. vulgaris reared in fiberglass tanks containing 70 m<sup>3</sup> of seawater salinity 25 ppt over a period of 70 days. Individual shrimps were fed with four different types of feeds i.e., newly hatched Artemia (Ar), rotifer (Ro), newly hatched Artemia + rotifer (ArRo) and shrimp larvae commercial feed (SF). Results suggested that specific growth rates (both for body weight and body length) of shrimps reared with SF were not significantly different with treatment feed with Ar, ArRo and Ro (p ≥ 0.05). The survival rate of A. vulgaris did not vary significantly (p ≥ 0.05) among the Ar, Ro and ArRo treatments. However, the highest survival rate of shrimp (81.78% ± 3.08%) was observed in SF treatment and the percentage of survival rate was significantly different with treatment feed with Ar, Ro and ArRo (p ≤ 0.05). The findings reflected the ability of Acetes shrimps to consume diverse food types including both live feed and pelleted feed. Insights obtained from this research suggested that artificial feed can be as efficient as live feeds. This new knowledge is a needed addition to a currently lacking knowledge base for aquaculture of this Acetes species.
文摘Objective:To analyze the clinical efficacy of megestrol acetate dispersible tablets in the adjuvant treatment of acute leukemia.Methods:80 patients with acute leukemia admitted from December 2021 to December 2022 were randomly divided into two groups.The control group underwent chemotherapy,and the observation group took megestrol acetate dispersible tablets and underwent chemotherapy.The effect of the treatments were evaluated by analyzing the albumin(Alb)and prealbumin(Palb)indicators,and the adverse reactions were observed.Results:There was no significant difference in Alb and Palb indexes between the two groups before treatment(P>0.05).After treatment,Alb and Palb indexes in the observation group were greater than those in the control group(P<0.05).The incidence of adverse reactions in the control group was 20.00%,which was significantly higher than the observation group(5.00%),with P<0.05.Conclusion:The combination of megestrol acetate dispersible tablets and chemotherapy is more effective in treating patients with acute leukemia,and the Alb and Palb indexes can be optimized.Besides,there are fewer adverse reactions,which means that the treatment is relatively safe.
文摘BACKGROUND Conventional magnifying endoscopy with narrow-band imaging(NBI)observation of the gastric body mucosa shows dominant patterns in relation to the regular arrangement of collecting venules,subepithelial capillary network,and gastric pits.AIM To evaluate the effectiveness of a new one-dual(near)focus,NBI mode in the assessment of the microscopic features of gastric body mucosa compared to conventional magnification.METHODS During 2021 and 2022,68 patients underwent proximal gastrointestinal endoscopy using magnification endoscopic modalities subsequently applying acetic acid(AA).The GIF-190HQ series NBI system with dual focus capability was used for the investigation of gastric mucosa.At the time of the endoscopy,the gastric body mucosa of all enrolled patients was photographed using the white light endoscopy(WLE),near focus(NF),NF-NBI,AA-NF,and AA-NF-NBI modes.RESULTS The WLE,NF and NF-NBI endoscopic modes for all patients(204 images)were classified in the same order into three groups.Two images from each patient for the AA-NF and AA-NF-NBI endoscopic modes were classified in the same order.According to all three observers who completed the work independently,NF magnification was significantly superior to WLE(P<0.01),and the NF-NBI mode was significantly superior to NF magnification(P<0.01).After applying AA,the three observers confirmed that AA-NF-NBI was significantly superior to AA-NF(P<0.01).Interobserver kappa values for WLE were 0.609,0.704,and 0.598,respectively and were 0.600,0.721,and 0.637,respectively,for NF magnification.For the NF-NBI mode,the values were 0.378,0.471,and 0.553,respectively.For AA-NF,they were 0.453,0.603,and 0.480,respectively,and for AA-NF-NBI,they were 0.643,0.506,and 0.354,respectively.CONCLUSION When investigating gastric mucosa in microscopic detail,NF-NBI was the most powerful endoscopic mode for assessing regular arrangement of collecting venules,subepithelial capillary network,and gastric pits among the five endoscopic modalities investigated in this study.AA-NF-NBI was the most powerful endoscopic mode for analyzing crypt opening and intervening part.
基金the China Scholarship Council(CSC)for funding(no.201806310116)。
文摘Mg-air batteries have attracted tremendous attention as a potential next-generation power source for portable electronics and e-transportation due to their remarkable high theoretical volumetric energy density,environmental sustainability,and cost-effectiveness.However,the fast hydrogen evolution reaction(HER)in NaCl-based aqueous electrolytes impairs the performance of Mg-air batteries and leads to poor specific capacity,low energy density,and low utilization.Thus,the conventionally used NaCl solute was proposed to be replaced by NaNO_(3)and acetic acid additive as a corrosion inhibitor,therefore an electrolyte engineering for long-life time Mg-air batteries is reported.The resulting Mg-air batteries based on this optimized electrolyte demonstrate an improved discharge voltage reaching~1.8 V for initial 5 h at a current density of 0.5 mA/cm^(2) and significantly prolonged cells'operational lifetime to over 360 h,in contrast to only~17 h observed in NaCl electrolyte.X-ray photoelectron spectroscopy and time-of-flight secondary ion mass spectrometry were employed to analyse the composition of surface film and scanning electron microscopy combined with transmission electron microscopy to clarify the morphology changes of the surface layer as a function of acetic acid addition.The thorough studies of chemical composition and morphology of corrosion products have allowed us to elucidate the working mechanism of Mg anode in this optimized electrolyte for Mg-air batteries.
文摘It was reported that hemispheric corrosion occurred in copper tubes in an acetic acid environment. When hemispheric corrosion occurred, corrosion could easily progress if water then flowed into the copper pipe, and countermeasures were needed. Therefore, we studied the copper corrosion caused by acetic acid. The present work investigated the relationship between the corrosion form of copper and acetic acid concentration using phosphorous-deoxidized copper, and reported that hemispherical corrosion was observed at acetic acid concentrations of 0.01 to 1 vol.% (0.002 to 0.2 mol·L<sup>-1</sup>) in the immersion test. In this study, the effects of acetic acid and phosphate on copper corrosion were examined using oxygen-free copper in immersion tests. The results suggested that different concentrations of phosphate in acetic acid solutions and the presence or absence of acetic acid and phosphate affected the corrosion of copper, resulting in different corrosion forms and corrosion progress.