Improvement of thermally grown oxide layer in thermal barrier coating systems with nano alumina as third layer

A thermally grown oxide （TGO） layer is formed at the interface of bond coat/top coat. The TGO growth during thermal exposure in air plays an important role in the spallation of the ceramic layer from the bond coat. High temperature oxidation resistance of four types of atmospheric plasma sprayed TBCs was investigated. These coatings were oxidized at 1000 °C for 24, 48 and 120 h in a normal electric furnace under air atmosphere. Microstructural characterization showed that the growth of the TGO layer in nano NiCrAlY/YSZ/nano Al2O3 coating is much lower than in other coatings. Moreover, EDS and XRD analyses revealed the formation of Ni（Cr,Al）2O4 mixed oxides （as spinel） and NiO onto the Al2O3 （TGO） layer. The formation of detrimental mixed oxides （spinels） on the Al2O3 （TGO） layer of nano NiCrAlY/YSZ/nano Al2O3 coating is much lower compared to that of other coatings after 120 h of high temperature oxidation at 1000 °C.

Microstructure and Contact Fatigue Behavior of Nano-SiO_2/Ni Coating Prepared by Electro-Brush Plating

The composite coating nano SiO 2/Ni was prepared by co depositing nano SiO 2 particles with pure nickel through electro brush plating. By taking into account the effect of microstructure, heat treatment and load on the contact fatigue life, the anti contact fatigue behavior of the composite coating was examined and compared with that of nickel coating. As a result, the contact fatigue life decreased with the increasing of load. The contact fatigue lives of nano SiO 2/Ni coating were 16.5% and 45.2% higher than those of nickel coating respectively under the loads of 60 N and 140 N, and 326.3% higher than its counterpart of nickel coating after annealed under the load of 140 N. From the SEM image of fatigue fracture, it has been observed that the fatigue fracture of the composite coating initiated in the sub surface as well as at the track surface due to the huddling of units, and propagated along the interface between grain units.

Application of Nano Coating （SiO2） on Textile Products

Liquid SiO2 solutions produced by silicon-based nano- powder are covered on the fabric surface by using spray method. Fabric surfaces were coated at the room temperature in air with the different spray nozzles. Surface analysis of the coated fabric was performed by using Contact Angle and SEM pictures. According to the Contact Angles measurements, the coated fabric surfaces showed hydrophobic character between 126 and 146 degrees, and the SiO2 particles sticked to the fabric fibers as seen from SEM picture.

The Effect and Mechanism of Nano-Cu Lubricating Additives on the Electroless Deposited Ni-W-P Coating

The coating and deposition process with excellent anti wear and suitable for industrial application were developed, and the optimum bath composition and process were obtained by studying the influence of the bath composition, temperature and pH value on the deposition rate and the plating solution stability. Moreover, the tribological properties of nano-Cu lubricating additives and electroless deposited Ni-W-P coating as well as their synergistic effect are researched using ring-block abrasion testing machine and energy dispersive spectrometer. Research results show that Ni-W-P alloy coating and nano-Cu lubricating additive have excellent synergistic effect, e g, the wear resistance of Ni-W-P alloy coating （with heat treatment and the oil with nano-Cu additives） has increased hundreds times than 45 steel as the metal substrate with the basic oil, and zero wear is achieved, which breaks through the bottleneck of previous separate research of the above-mentioned two aspects.

Effects of Surfactants SDS and CTAB on Ni-SiC Deposition

The influences of surfactant type and concentration on the content and uniformity of SiC particles in Ni-SiC deposit were studied in this paper. The electrochemical behavior of preparing Ni-SiC composite coating was investigated using the cyclic voltammetry method. Then the impact of surfactants on the deposition potential of Ni-SiC coating was analyzed. Electrochemical studies showed that the cathode overvoltage increases gradually with increasing SDS（Sodium dodecyl sulfate） concentration. The CV curve showed the shift towards a lower current at a given potential with increasing SDS concentration. Ni-SiC composite coatings were prepared by electrodeposition. The experimental results show that the dispersion of 40 nm SiC in Ni-SiC coating obtained in the electrolyte containing SDS is superior that containing CTAB（cetyltrimethyl ammonium bromide）. CTAB increases the content of 40 nm SiC particles in the Ni-SiC coating, but the uniformity of 40 nm SiC particles in Ni-SiC composite coating is poor. SiC particles are still agglomerated. Compared with the anionic surfactant SDS and the cationic surfactant CTAB, surfactant SDS makes the particles better dispersed. But the contribution of surfactant SDS for co-deposition amount of SiC particles is negligible. The cationic surfactant CTAB can effectively improve the suspension performance of SiC particles and promote the co-deposition of SiC particles and metallic nickel. But there is still some reunion of SiC.