Based on the composite modification technology of the surface of nano Silicondioxide by non-soap emulsion polymerization, it is verified that there are polymer grafted on thesurface of nano silicon dioxide. The modifi...Based on the composite modification technology of the surface of nano Silicondioxide by non-soap emulsion polymerization, it is verified that there are polymer grafted on thesurface of nano silicon dioxide. The modification mechanism and the bonding status on the surface ofnano silicon dioxide after modification were suggested via the results of the infrared spectrum,transmission electronic microscope photograph and X-ray photoelectron spectrum. The hydroxyl formedby hydrolyzing of silane coupling agent reacts with hydroxyl on the surface of nano silicon dioxideto form Si-O-Si bonds by losing water molecules and hence the double bonds are introduced onto thesurface of nano silicon dioxide. The surface of nano silicon dioxide is grafted with polymer throughfree radical polymerization between the double bonds on the surface of nano silicon dioxide andstyrene under the action of initiating agent. The dispersibility of nano silicon dioxide and thecontrollability of surface modification of nano silicon dioxide can be greatly improved by themodification process.展开更多
Si3N4-Si2N2O composites were fabricated with amorphous nano-sized silicon nitride powders by the liquid phase sintering （ LPS ）. The Si2 N2O phase was generated by an in-situ reaction 2 Si3 N4 （ s ） ＋ 1.5 02 （ g...Si3N4-Si2N2O composites were fabricated with amorphous nano-sized silicon nitride powders by the liquid phase sintering （ LPS ）. The Si2 N2O phase was generated by an in-situ reaction 2 Si3 N4 （ s ） ＋ 1.5 02 （ g ） = 3 Si2 N2O （ s ） ＋ N2 （ g ） . The content of Si2 N2 O phase up to 60% in the volume was obtained at a sintering temperature of 1 650℃ and reduced when the sintering temperature increased or decreased, indicating the reaction is reversible. The mass loss, relative density and average grain size increased with increasing the sintering temperature. The average grain size was less than 500 nm when the sintering temperature was below 1 700 ℃. The sintering procedure contains a complex crystallization and a phase transition ： amorphous silicon nitride→equiaxial α- Si3 N4→ equiaxial β- Si3 N4→ rod- like Si2 N2O→ needle- like β- Si3N4 . Small round-shaped β→ Si3 N4 particles were entrapped in the Si2 N2O grains and a high density of staking faults was situated in the middle of Si2 N2O grains at a sintering temperature of 1 650 ℃. The toughness inereased from 3.5 MPa·m^1/2 at 1 600 ℃ to 7.2 MPa· m^1/2 at 1 800 ℃ . The hardness was as high as 21.5 GPa （Vickers） at 1 600 ℃ .展开更多
A series of nano silica/silicone modified waterborne polyurethane(WPU) have been synthesized from polytetramethylene glycol and isophorone diisocyanate, dihydroxymethyl propionic acid and triethylamine, ethylenediamin...A series of nano silica/silicone modified waterborne polyurethane(WPU) have been synthesized from polytetramethylene glycol and isophorone diisocyanate, dihydroxymethyl propionic acid and triethylamine, ethylenediamine, trimethylolpropane, nano-SiO2 and the silane coupling agent KH550. The effect of the dosage of nano-SiO2 on the WPU-Si membrane and the coated RDX(cyclotrimethylenetrinitramine) particles have been studied in terms of their surface properties, mechanical properties, and thermal stability. The results showed that with the increase of Si content, the stability of the emulsion reduced gradually. The material with more Si content displayed an increased thermodynamic stability, an increased high temperature resistance, an increased tensile strength and a decreased elongation at break. With the increase of Si content, the surface tension of the material decreased, the bibulous rate reduced, and the contact angle increased gradually, so that the surface tension of the polyurethane and RDX are close to each other which could improve the performance of coating.展开更多
Nano silicon particles can be become nano fibre under low energy electron beam bombarding. The formation of the nano silicon fibre include two stages. At first, on the nano silicon particle surface many ...Nano silicon particles can be become nano fibre under low energy electron beam bombarding. The formation of the nano silicon fibre include two stages. At first, on the nano silicon particle surface many silicon atoms are gasified, then these silicon atoms deposit in the place where have more charge on account of the static electrical absorption and the point effect of the charge accumulation , these atoms grow into non crystalline silicon fibres. The second stage is the non crystalline silicon fibres crystallizing. Its crystallizing temperature is about 180℃. The growth mechanism of the nano silicon fibre is vapour solid mode.展开更多
A novel EVA/unmodified nano-magnesium hydroxide （NMH）/silicone rubber ternary nanocomposite was prepared by using a special compound flame retardant of NMH and silicone rubber （CFR）. The flammability of the ternar...A novel EVA/unmodified nano-magnesium hydroxide （NMH）/silicone rubber ternary nanocomposite was prepared by using a special compound flame retardant of NMH and silicone rubber （CFR）. The flammability of the ternary composite was studied by cone calorimeter test （CCT）. Synergistic effect on flame retardancy was found between silicone rubber and NMH. EVA/CFR ternary nanocomposite showed the lowest peak heat release rate （PHRR） and mass loss rate （MLR） among the samples of virgin EVA, EVA composites. The synergistic flame retardancy of silicone rubber and NMH in EVA system is attributed to the enhanced char layers in the condensed phase that prevents the heat and mass transfer in the fire.展开更多
To understand the deformation and removal mechanism of material on nano-scale at ultralow loads,a systemic study on AFM micro/nano-machining on single crystal ailicon is conducted. The results indicate that AFM nano- ...To understand the deformation and removal mechanism of material on nano-scale at ultralow loads,a systemic study on AFM micro/nano-machining on single crystal ailicon is conducted. The results indicate that AFM nano- machining has a precisely dimensional controllability and a good surface quality on nanometer scale.A SEM is adopted to observe nano-machined region and chips,the results indicate that the material removal mechanisms change with the applied normal load. An XPS is used to analyze the changes of chemical composition inside and outside the nano-machined region respectively.The nano-indentation which is conducted with the same AFM diamond tip on the machined region shows a big discrepancy compared with that on the macro-scale. The calculated results show higher nano-hardness and elastic modulus than normal values .This phenomenon on be regarded as the indentation size effect(ISE).展开更多
It was reported that due to the non-linear electrical phenomena,the super-saturated arsenic in silicon single crystalline precipitates during post processing at low temperatures to form different structures.The struct...It was reported that due to the non-linear electrical phenomena,the super-saturated arsenic in silicon single crystalline precipitates during post processing at low temperatures to form different structures.The structure with spatial period of 1.7 to 2.3 nm was observed firstly by TEM on the sample.展开更多
The article has been retracted due to the investigation of complaints received against it. The Editorial Board found that substantial portions of the text came from other published paper. Comparing with the paper publ...The article has been retracted due to the investigation of complaints received against it. The Editorial Board found that substantial portions of the text came from other published paper. Comparing with the paper published in International Journal of Engineering, Science and Technology Vol. 3, No. 4, 2011, pp. 82-88 (www.ijest-ng.com), these two papers have the same contents before Figure 7 and the author added Fig. 8, 9, 10 on the 2012 paper. The scientific community takes a very strong view on this matter, and the Journal of Minerals and Materials Characterization and Engineering (JMMCE) treats all unethical behavior seriously. This paper published in Vol.11 No.5, 529-541, 2012 has been removed from this site.展开更多
In the present work, a Cz-Silicon wafer is implanted with helium ions to produce a buried porous layer, and then thermally annealed in a dry oxygen atmosphere to make oxygen transport into the cavities. The formation ...In the present work, a Cz-Silicon wafer is implanted with helium ions to produce a buried porous layer, and then thermally annealed in a dry oxygen atmosphere to make oxygen transport into the cavities. The formation of the buried oxide layer in the case of internal oxidation （ITOX） of the buried porous layer of cavities in the silicon sample is studied by positron beam annihilation （PBA）. The cavities are formed by 15 keV He implantation at a fluence of 2×10^16 cm^-2 and followed by thermal annealing at 673 K for 30 min in vacuum. The internal oxidation is carried out at temperatures ranging from 1073 to 1473 K for 2 h in a dry oxygen atmosphere. The layered structures evolved in the silicon are detected by using the PBA and the thicknesses of their layers and nature are also investigated. It is found that rather high temperatures must be chosen to establish a sufficient flux of oxygen into the cavity layer. On the other hand high temperatures lead to coarsening the cavities and removing the cavity layer finally.展开更多
In systems in atomic and nano scales such as clusters or agglomerates constituted of particles from a few to less than one hundred of atoms, quantum confinement effects are very important. Their optical and electronic...In systems in atomic and nano scales such as clusters or agglomerates constituted of particles from a few to less than one hundred of atoms, quantum confinement effects are very important. Their optical and electronic properties are often dependent on the size of the systems and the way in which the atoms in these clusters are bonded. Generally, these nano-structures display optical and electronic properties significantly different of those found in corresponding bulk materials. Silicon agglomerates found in Silicon Rich Oxide (SRO) films have optical properties, which have reported as depended directly on nano-crystal size. Furthermore, the room temperature photoluminescence (PL) of Silicon Rich Oxides (SRO) has repeatedly generated a huge interest due to their possible applications in optoelectronic devices. However, a plausible emission mechanism has not yet widespread acceptance of the scientific community. In this research, we employed the Density Functional Theory with a functional B3LYP and a basis set 6 - 31G* to calculate the optical and electronic properties of small (six to ten silicon atoms) and medium size clusters of silicon (constituted of eleven to fourteen silicon atoms). With the theoretical calculation of the structural and optical properties of silicon clusters, it is possible to evaluate the contribution of silicon agglomerates in the luminescent emission mechanism experimentally found in thin SRO films.展开更多
The photoluminescence(PL)dynamics of nano-silicon prepared in various environments is investigated,which involves the emission in nanostructures related to a wider band from 550 nm to 900 nm and the localized states e...The photoluminescence(PL)dynamics of nano-silicon prepared in various environments is investigated,which involves the emission in nanostructures related to a wider band from 550 nm to 900 nm and the localized states emission at 694 nm,605 nm,604 nm and 560 nm.It is observed that the sharp PL peak on the samples prepared in nitrogen has the shape of single tip near 605 nm,but the shape of twin tips always occurs in the two sharp peaks on the samples prepared in oxygen.The threshold behavior and the optical gain are discovered in the PL emission at 694 nm,605 nm and 604 nm.The experiments demonstrate that the optimum pressure to prepare samples in oxygen for the enhancement of emission near 700 nm is about 10~100 Pa,and the optimum one in oxygen for the enhancement of emission near 600 nm is about 1/10~1 Pa,while in high vacuum(<10μPa) the PL emission becomes weaker.展开更多
A three-dimensional dynamic model for nano/micro-fabrications of silicon was presented. With the developed model, the fabrication process of silicon on nothing（SON） structure was quantitatively investigated. We empl...A three-dimensional dynamic model for nano/micro-fabrications of silicon was presented. With the developed model, the fabrication process of silicon on nothing（SON） structure was quantitatively investigated. We employ a diffuse interface model that incorporates the mechanism of surface diffusion. The mechanism of the fabrication is systematically integrated for high reliability of computational analysis. A semi-implicit Fourier spectral scheme is applied for high efficiency and numerical stability. Moreover, the theoretical analysis provides the guidance that is ordered by the fundamental geometrical design parameters to guide different fabrications of SON structures. The performed simulations suggest a substantial potential of the presented model for a reliable design technology of nano/micro-fabrications.展开更多
文摘Based on the composite modification technology of the surface of nano Silicondioxide by non-soap emulsion polymerization, it is verified that there are polymer grafted on thesurface of nano silicon dioxide. The modification mechanism and the bonding status on the surface ofnano silicon dioxide after modification were suggested via the results of the infrared spectrum,transmission electronic microscope photograph and X-ray photoelectron spectrum. The hydroxyl formedby hydrolyzing of silane coupling agent reacts with hydroxyl on the surface of nano silicon dioxideto form Si-O-Si bonds by losing water molecules and hence the double bonds are introduced onto thesurface of nano silicon dioxide. The surface of nano silicon dioxide is grafted with polymer throughfree radical polymerization between the double bonds on the surface of nano silicon dioxide andstyrene under the action of initiating agent. The dispersibility of nano silicon dioxide and thecontrollability of surface modification of nano silicon dioxide can be greatly improved by themodification process.
基金Funded by the National Science Foundation of China ( No.50375037)
文摘Si3N4-Si2N2O composites were fabricated with amorphous nano-sized silicon nitride powders by the liquid phase sintering （ LPS ）. The Si2 N2O phase was generated by an in-situ reaction 2 Si3 N4 （ s ） ＋ 1.5 02 （ g ） = 3 Si2 N2O （ s ） ＋ N2 （ g ） . The content of Si2 N2 O phase up to 60% in the volume was obtained at a sintering temperature of 1 650℃ and reduced when the sintering temperature increased or decreased, indicating the reaction is reversible. The mass loss, relative density and average grain size increased with increasing the sintering temperature. The average grain size was less than 500 nm when the sintering temperature was below 1 700 ℃. The sintering procedure contains a complex crystallization and a phase transition ： amorphous silicon nitride→equiaxial α- Si3 N4→ equiaxial β- Si3 N4→ rod- like Si2 N2O→ needle- like β- Si3N4 . Small round-shaped β→ Si3 N4 particles were entrapped in the Si2 N2O grains and a high density of staking faults was situated in the middle of Si2 N2O grains at a sintering temperature of 1 650 ℃. The toughness inereased from 3.5 MPa·m^1/2 at 1 600 ℃ to 7.2 MPa· m^1/2 at 1 800 ℃ . The hardness was as high as 21.5 GPa （Vickers） at 1 600 ℃ .
基金the financial support by the National Natural Science Foundation of China(No.20973022 and No.11472048)
文摘A series of nano silica/silicone modified waterborne polyurethane(WPU) have been synthesized from polytetramethylene glycol and isophorone diisocyanate, dihydroxymethyl propionic acid and triethylamine, ethylenediamine, trimethylolpropane, nano-SiO2 and the silane coupling agent KH550. The effect of the dosage of nano-SiO2 on the WPU-Si membrane and the coated RDX(cyclotrimethylenetrinitramine) particles have been studied in terms of their surface properties, mechanical properties, and thermal stability. The results showed that with the increase of Si content, the stability of the emulsion reduced gradually. The material with more Si content displayed an increased thermodynamic stability, an increased high temperature resistance, an increased tensile strength and a decreased elongation at break. With the increase of Si content, the surface tension of the material decreased, the bibulous rate reduced, and the contact angle increased gradually, so that the surface tension of the polyurethane and RDX are close to each other which could improve the performance of coating.
文摘Nano silicon particles can be become nano fibre under low energy electron beam bombarding. The formation of the nano silicon fibre include two stages. At first, on the nano silicon particle surface many silicon atoms are gasified, then these silicon atoms deposit in the place where have more charge on account of the static electrical absorption and the point effect of the charge accumulation , these atoms grow into non crystalline silicon fibres. The second stage is the non crystalline silicon fibres crystallizing. Its crystallizing temperature is about 180℃. The growth mechanism of the nano silicon fibre is vapour solid mode.
基金This work was subsidized by the Special Funds for Major State Basic Research Projects(No.2005CB623800).
文摘A novel EVA/unmodified nano-magnesium hydroxide （NMH）/silicone rubber ternary nanocomposite was prepared by using a special compound flame retardant of NMH and silicone rubber （CFR）. The flammability of the ternary composite was studied by cone calorimeter test （CCT）. Synergistic effect on flame retardancy was found between silicone rubber and NMH. EVA/CFR ternary nanocomposite showed the lowest peak heat release rate （PHRR） and mass loss rate （MLR） among the samples of virgin EVA, EVA composites. The synergistic flame retardancy of silicone rubber and NMH in EVA system is attributed to the enhanced char layers in the condensed phase that prevents the heat and mass transfer in the fire.
基金This project is supported by National Natural ScienceFoundation of China (No.59835180) and Science andTechnology Foundatio
文摘To understand the deformation and removal mechanism of material on nano-scale at ultralow loads,a systemic study on AFM micro/nano-machining on single crystal ailicon is conducted. The results indicate that AFM nano- machining has a precisely dimensional controllability and a good surface quality on nanometer scale.A SEM is adopted to observe nano-machined region and chips,the results indicate that the material removal mechanisms change with the applied normal load. An XPS is used to analyze the changes of chemical composition inside and outside the nano-machined region respectively.The nano-indentation which is conducted with the same AFM diamond tip on the machined region shows a big discrepancy compared with that on the macro-scale. The calculated results show higher nano-hardness and elastic modulus than normal values .This phenomenon on be regarded as the indentation size effect(ISE).
文摘It was reported that due to the non-linear electrical phenomena,the super-saturated arsenic in silicon single crystalline precipitates during post processing at low temperatures to form different structures.The structure with spatial period of 1.7 to 2.3 nm was observed firstly by TEM on the sample.
文摘The article has been retracted due to the investigation of complaints received against it. The Editorial Board found that substantial portions of the text came from other published paper. Comparing with the paper published in International Journal of Engineering, Science and Technology Vol. 3, No. 4, 2011, pp. 82-88 (www.ijest-ng.com), these two papers have the same contents before Figure 7 and the author added Fig. 8, 9, 10 on the 2012 paper. The scientific community takes a very strong view on this matter, and the Journal of Minerals and Materials Characterization and Engineering (JMMCE) treats all unethical behavior seriously. This paper published in Vol.11 No.5, 529-541, 2012 has been removed from this site.
文摘In the present work, a Cz-Silicon wafer is implanted with helium ions to produce a buried porous layer, and then thermally annealed in a dry oxygen atmosphere to make oxygen transport into the cavities. The formation of the buried oxide layer in the case of internal oxidation （ITOX） of the buried porous layer of cavities in the silicon sample is studied by positron beam annihilation （PBA）. The cavities are formed by 15 keV He implantation at a fluence of 2×10^16 cm^-2 and followed by thermal annealing at 673 K for 30 min in vacuum. The internal oxidation is carried out at temperatures ranging from 1073 to 1473 K for 2 h in a dry oxygen atmosphere. The layered structures evolved in the silicon are detected by using the PBA and the thicknesses of their layers and nature are also investigated. It is found that rather high temperatures must be chosen to establish a sufficient flux of oxygen into the cavity layer. On the other hand high temperatures lead to coarsening the cavities and removing the cavity layer finally.
文摘In systems in atomic and nano scales such as clusters or agglomerates constituted of particles from a few to less than one hundred of atoms, quantum confinement effects are very important. Their optical and electronic properties are often dependent on the size of the systems and the way in which the atoms in these clusters are bonded. Generally, these nano-structures display optical and electronic properties significantly different of those found in corresponding bulk materials. Silicon agglomerates found in Silicon Rich Oxide (SRO) films have optical properties, which have reported as depended directly on nano-crystal size. Furthermore, the room temperature photoluminescence (PL) of Silicon Rich Oxides (SRO) has repeatedly generated a huge interest due to their possible applications in optoelectronic devices. However, a plausible emission mechanism has not yet widespread acceptance of the scientific community. In this research, we employed the Density Functional Theory with a functional B3LYP and a basis set 6 - 31G* to calculate the optical and electronic properties of small (six to ten silicon atoms) and medium size clusters of silicon (constituted of eleven to fourteen silicon atoms). With the theoretical calculation of the structural and optical properties of silicon clusters, it is possible to evaluate the contribution of silicon agglomerates in the luminescent emission mechanism experimentally found in thin SRO films.
基金National Natural Science Foundation of China(Grant No.11264007)
文摘The photoluminescence(PL)dynamics of nano-silicon prepared in various environments is investigated,which involves the emission in nanostructures related to a wider band from 550 nm to 900 nm and the localized states emission at 694 nm,605 nm,604 nm and 560 nm.It is observed that the sharp PL peak on the samples prepared in nitrogen has the shape of single tip near 605 nm,but the shape of twin tips always occurs in the two sharp peaks on the samples prepared in oxygen.The threshold behavior and the optical gain are discovered in the PL emission at 694 nm,605 nm and 604 nm.The experiments demonstrate that the optimum pressure to prepare samples in oxygen for the enhancement of emission near 700 nm is about 10~100 Pa,and the optimum one in oxygen for the enhancement of emission near 600 nm is about 1/10~1 Pa,while in high vacuum(<10μPa) the PL emission becomes weaker.
基金the National Natural Science Foundation of China(No.51775154)the ZheJiang Provincial Natural Science Foundation of China(No.LZ15E050004)
文摘A three-dimensional dynamic model for nano/micro-fabrications of silicon was presented. With the developed model, the fabrication process of silicon on nothing（SON） structure was quantitatively investigated. We employ a diffuse interface model that incorporates the mechanism of surface diffusion. The mechanism of the fabrication is systematically integrated for high reliability of computational analysis. A semi-implicit Fourier spectral scheme is applied for high efficiency and numerical stability. Moreover, the theoretical analysis provides the guidance that is ordered by the fundamental geometrical design parameters to guide different fabrications of SON structures. The performed simulations suggest a substantial potential of the presented model for a reliable design technology of nano/micro-fabrications.
