Efficient Sequestration of Congo Red Dye from Aqueous Solutions Using Pamam Dendrimer-Silica Composite

This study investigates the removal of Congo Red dye from aqueous solution using functionalized generation 3.0 and 5.0 polyamidoamine dendrimer-silica gel composite (G-3PS, G-5PS). Fourier Transform-Infra Red spectroscopy, Brunauer Emmett and Teller, Thermo Gravimetric Analysis, pH at point of zero charge, and scanning electron microscopy measurements have been applied to characterize the synthetic nanohybrid composite, these techniques revealed the successful functionalization of both dendrimer molecules and subsequent immobilization onto silica gel. The implications of varying adsorption parameters such as contact time, initial concentration of adsorbate, temperature and pH on both composites were studied. Experimental data obtained from batch adsorption processes were fitted into two equilibrium isotherms (Langmuir and Freundlich) and 3 kinetic models (Pseudo-First-Order, Pseudo-Second-Order, Intra Particle Diffusion). Adsorption mechanism was mainly governed by film diffusion due to electrostatic interactions between the functionalized dendrimer surface and Congo Red molecules. Thermodynamic parameters illustrate that the adsorption is endothermic and spontaneous. Findings suggest the Nanocomposites (G-3PS and G-5PS) are good adsorbents for the removal of Congo Red dye from aqueous solutions.

TPU/Nano-ZnO复合改性沥青的性能研究及微观机制

为促进聚合物/纳米改性沥青在耐久性路面中的应用,在实验室将不同掺量的聚氨酯及纳米氧化锌添加到A-70#基质沥青中制备了复合改性沥青。采用传统物理性能试验、动态剪切流变试验(DSR)、弯曲梁流变试验(BBR)研究了其物理性能与流变特性,基于响应面法的优化设计来明确两种改性剂的最佳掺量。借助傅里叶红外光谱试验(FTIR)对其微观改性机理进行探讨。采用高压紫外汞灯环境箱对改性沥青进行不同时间的紫外老化,分析其抗紫外老化能力,并基于主成分分析法评价了老化性能测试指标的显著性。结果表明:聚氨酯与纳米氧化锌的共同作用提高了基质沥青的高温稳定性及低温抗裂性,两种改性剂的最佳掺量分别为5%、3%。根据FTIR结果,复合改性沥青的改性过程既存在物理共混,又有化学加成反应。聚氨酯及纳米氧化锌的加入在基质沥青紫外老化过程中能够抑制羰基、亚砜基等极性基团的生成,复数剪切模量、羰基指数、劲度模量及亚砜基指数对沥青紫外老化性能的影响最为显著。

抗菌PP/Rnano-ZnO复合材料的制备及性能研究

以棒状纳米氧化锌(Rnano-ZnO)为抗菌剂、聚丙烯(PP)为基材,采用熔融共混法在双螺杆挤出机中制备了抗菌PP/Rnano-ZnO复合材料。测试了复合材料的抗菌性能,通过DSC法研究了抗菌PP/Rnano-ZnO复合材料中Rnano-ZnO质量分数对结晶性能的影响,采用SEM分析了复合材料冲击断面的微观形貌,采用万能电子拉伸机测试了复合材料的力学性能。结果表明,抗菌PP/Rnano-ZnO复合材料中随着Rnano-ZnO的加入,结晶温度提高了1.81℃,相对结晶度提高了5.03%,冲击强度提高了47.83%,拉伸强度提高了20.96%和断裂伸长率提高了4790%;当抗菌PP/Rnano-ZnO复合材料中Rnano-ZnO质量分数为6.0%时,其力学性能、对大肠杆菌和金黄色葡萄球菌的抗菌效果最佳。

Characterization of cast A356 alloy reinforced with nano SiC composites

The microstructure and mechanical properties of nano composites processed via stir casting were studied. The composites were based on the A356 aluminum alloy reinforced with nano SiC particles. The density measurements show that the samples contain little porosity and the amount of porosity in the composites increases with increasing volume fraction of SiC. The microstructures of the composites were examined using optical microscope and transmission electron microscope. Microscopic observations of the microstructures reveal that the dispersion of the particles is uniform. The yield strength, ultimate tensile strength and the elastic modulus are improved with the addition of nano particles although some reduction in ductility is observed. The highest yield strength and ultimate tensile strength are obtained with the addition of 3.5% SiC nano-particles. A relatively ductile fracture in tensile fractured samples was observed by fractography examination.

Fabrication and Thermal Insulating Properties of ITO/PVB Nanocomposites for Energy Saving Glass

Chemical co-precipitation method was used to synthesize tin-doped indium oxide（ITO）nanoparticles,and the subsequent solution co-blend was employed to fabricate ITO/PVB nanocomposites.UV（Ultra-violet）-Vis（Visible）-NIR（Near Infrared） spectra show that the addition of ITO nano particles can significantly enhance the thermal insulating efficiency of ITO/PVB nanocomposites.With increasing ITO content,the thermal insulating efficiency is increased.UV is almost fully absorbed by all ITO/PVB nanocomposites.Vis transmittance-haze spectra reveal that ITO/PVB nanocomposites exhibit higher Vis transmittance over 71.3%and lower haze below 2%when ITO content is in the range of 0.1 wt%-0.7 wt%.The UV-Vis-NIR spectroscopy shows that,under the premise of over 70%transmittance to the visible light,the screening effect of the NIR can be enhanced by 80%with 0.7%ITO/PVB nanocomposite membrane compared with the undoped PVB.The thermal insulating tests indicate that,in comparison with the pure PVB film,nanocomposite films with 0.1 wt%-0.9 wt%ITO can reduce temperature by 3-8 ℃.The results show that this novel nanocomposite can be used for energy-saving glass.

Fabrication and Thermal Insulating Properties of ATO/PVB Nanocomposites for Energy Saving Glass

The pechini method was used to synthesize antimony-doped tin oxide （ATO） nanoparticles, and the subsequent solution co-blend was employed to fabricate ATO/PVB nanocomposites. Uv-Vis-NIR spectra show that the addition ofATO nano particles can significantly enhance the thermal insulating efficiency of ATO/PVB nanocomposites. With the increase of ATO content, the thermal insulating efficiency is increased. Uv is almost fully absorbed by all ATO/PVB nanocomposites. Vis transmittance-haze spectra reveal that ATO/ PVB nanocomposites exhibit higher Vis transmittance of over 72.7% and lower haze of below 2% when ATO content is in the range of 0.1 wt%-0.5 wt%. The thermal insulating tests indicate that in comparison with the pure PVB film, nanocomposite films with 0.1 wt%-0.5 wt% ATO can reduce temperature of 1-3 ℃, suggesting that this novel nanocomposite can be used for energy-saving glass.

ENHANCED MECHANICAL PROPERTIES OF POLYPROPYLENE/SILICA NANOCOMPOSITES WITH SURFACE MODIFICATION OF NANO-SILICA VIA IN SITU COPOLYMERIZATION OF METHYL METHACRYLATE AND BUTYL ACRYLATE

Nano-sized silica particles were modified with methacryloxy-propyltrimethoxysilane(MPS) followed by in situ copolymerization of methyl methacrylate(MMA) and butyl acrylate(BA).These modified nanoparticles were compounded with polypropylene(PP) to prepare PP/silica nanocomposites.PMMA grafted on nano-silica enhances the dispersion of the nanoparticles and interfacial adhesion,decreases the size of PP spherulites in nanocomposites and leads to increasing the Young's modulus and toughness of PP/silica nanocomp...

Preparation of multi-walled carbon nanotube–Fe composites and their application as light weight and broadband electromagnetic wave absorbers

Multi-walled carbon nanotube （MWCNT）-Fe composites were prepared via the metal organic chemical vapor deposi- tion by depositing iron pentacarbonyl on the surface of MWCNTs. The structural and morphological analyses demonstrated that Fe nanoparticles were deposited on the surface of the MWCNTs. The electromagnetic properties of the MWCNTs were significantly changed, and the absorbing capacity evidently improved after the Fe deposition on the MWCNT surface. A minimum reflection loss of -29.4 dB was observed at 8.39 GHz, and the less than -10 dB bandwidth was about 10.6 GHz, which covered the whole X band （8.2-12.4 GHz） and the whole Ku band （12.4-18 GHz）, indicating that the MWCNT-Fe composites could be used as an effective microwave absorption material.

DIELECTRIC PROPERTIES OF NANO Si/C/N COMPOSITE POWDER AND NANO SiC POWDER AT HIGH FREQUENCIES AND MICROSTRUCTURE CHARACTERIZATION

The dielectric properties of nano Si/C/N composite powder and nano SiC powder at high frequencies have been studied. The nano Si/C/N composite powder and nano SiC powder were synthesized from hexamethyldisilazane ((Me 3Si) 2NH) (Me:CH 3) and SiH 4 C 2H 2 respectively by a laser induced gas phase reaction. The complex permittivities of the nano Si/C/N composite powder and nano SiC powder were measured between 8 2GHz and 12 4GHz. The real and imaginary parts of the complex permittivities of nano Si/C/N composite powder are much higher than those of nano SiC powder. The SiC microcrystalline in the nano Si/C/N composite powder dissolved a great deal of nitrogen. The local structure around Si atoms changed by introducing N into SiC. Carbon atoms around Si were substituted by N atoms. So charged defects and quasi free electrons moved in response to the electric field, diffusion or polarization current resulted from the field propagation. The high ε″and loss factor tgδ(ε″/ε′) of Si/C/N composite powder were due to the dielectric relaxation.

Synergistic effect of magnetic field and nanocomposite pour point depressant on the yield stress of waxy model oil

Yield stress,as the key parameter to characterize the network strength of waxy oil,is important to the petroleum pipeline safety.Reducing the yield stress of waxy oil is of great significance for flow assurance.In this study,the effect of alternating magnetic field(intensity,frequency)on the yield stress of a waxy model oil with nanocomposite pour point depressant(NPPD)is systematically investigated.An optimum magnetic field intensity and frequency is found for the reduction in yield stress.When adding with NPPD,the heterogeneous nucleation of NPPD contributes to the reduction in yield stress for waxy model oil.Interestingly,the magnetic field is helpful for the modification of yield stress at a lower frequency and intensity before the optimal value;however,the modification is found to be weakened when the magnetic field is further increased after the optimal value.Possible explanation is proposed that the aggregation morphology of wax crystal would be altered and results in the release of wrapped oil phase from the network structure under the magnetic field.

Preparation of Molecularly Imprinted Composites Initiated by Hemin/Graphene Hybrid Nanosheets and Its Application in Detection of Sulfamethoxazole

Molecularly imprinted polymers(MIPs)exhibit high selectivity resulting from imprinted cavities and superior performance from functional materials,which have attracted much attention in many fields.However,the combination of MIPs film and functional materials is a great challenge.In this study,hemin/graphene hybrid nanosheets(H-GNs)were used to initiate the imprinted polymerization by catalyzing the generation of free radicals.Thus,MIPs using sulfamethoxazole as the template was directly prepared on the surface of H-GNs without any film modification.Most importantly,the template could be absorbed on the H-GNs to enhance the number of imprinted sites per unit surface area,which could improve the selectivity of MIPs film.Thus,the composites could exhibit high adsorption capacity(29.4 mg/g),imprinting factor(4.2)and excellent conductivity,which were modified on the surface of electrode for rapid,selective and sensitive detection of sulfamethoxazole in food and serum samples.The linear range was changed from 5μg/kg to 1 mg/g and the limit of detection was 1.2μg/kg.This sensor was free from interference caused by analogues of sulfamethoxazole,which provides a novel insight for the preparation of MIPs-based sensor and its application in food safety monitoring and human exposure study.

Sliding wear behaviour of AZ31B magnesium alloy and nano-composite

AZ31B magnesium alloy and nano-composite were manufactured by hybrid casting process and hot extruded at 350 °C. The sliding wear behaviour of alloy and nano-composite was estimated at room temperature using the standard pin-on-disc wear test equipment. The tests were conducted under a normal load of 10 N at different sliding speeds ranging from 0.60 to 1.2 m/s for distance up to 2000 m. The wear mechanisms of the worn out surface were studied using SEM analysis. The influence of test parameters on wear rate of the pins was established using a linear regression model statistically. Compared with the AZ31B magnesium alloy, the nano-composite shows lower wear rates due to higher hardness improvement caused by the reinforcement. The wear mechanism appears to be a mix-up of ploughing, rows of furrows, delamination and oxidation.

Influence of volume percentage of NanoTiB2 particles on tribological&mechanical behaviour of 6061-T6 Al alloy nano-surface composite layer prepared via friction stir process

The aim of present study is to analyze the influence of volume percentage(vol.%) of nano-sized particles(TiB_2: average size is 35 nm) on microstructure, mechanical and tribological behavior of 6061-T6 Al alloy surface nano composite prepared via Friction stir process(FSP). The microstructure of the fabricated surface nanocomposites is examined using optical microscopy(OM) and scanning electron microscope(SEM) for distribution of TiB_2 nano reinforcement particles, thickness of nano composite layer formed on the Aluminum alloy substrate and fracture features. The depth of surface nano composite layer is measured as 3683.82 m m along the cross section of stir zone of nano composite perpendicular to FSP. It was observed that increase in volume percentage of TiB_2 particles, the microhardness is increased up to132 Hv and it is greater than as-received Al alloy's microhardness(104 Hv). It is also observed that at 4volume percentage higher tensile properties exhibited as compared with the 2 and 8 vol. %. It is found that high wear resistance exhibited at 4 volume percentage as-compared with the 2 and 8 vol. %. The observed wear and mechanical properties are interrelated with microstructure, fractography and worn morphology.

Microstructure,mechanical response and fractography of AZ91E/Al_(2)O_(3)_(p) nano composite fabricated by semi solid stir casting method

The present study confers to the fabrication and its characterization of magnesium alloy(AZ91E)based nano composites with nano Al_(2)O_(3) particulate reinforcements.A novel Semi Solid stir casting technique was adopted for the fabrication of the composite.An average particle size of 50 nm was used as reinforcement to disperse in matrix.The effects of change in weight fraction of reinforcements on the distribution of particles,particle–matrix interfacial reactions,physical as well as mechanical properties were reported.The SEM and EDS analysis has shown the uniform distribution of particles in the composite along with the presence of elements.The mechanical properties of reinforced and unreinforced composite were evaluated and presented.Fractography of tensile specimens was also discussed.

Fabrication and Mechanical Properties of Sm2O3 Doped CeO2 Reinforced Ti3AlC2 Nano Composite

The fabrication process of Sm2O3 doped CeO2 reinforced Ti3AlC2 nano composites including the nano particle dispersion process by a hetero-coagulation process was developed using in-situ synthesis and densification process of Ti3AlC2. The effects of Sm2O2 doped CeO2 nano particles on mechanical properties of Ti3AlC2 were investigated. It was found that the presence of 20SDC nano particles in Ti3AlC2 was very effective to improve the mechanical properties of Ti3AlC2 without spoiling the unique characteristics of Ti3AlC2temary carbide.

Micro mechanical properties of n-Al2O3/Ni composite coating by nanoindentation

A new type of nano test system was introduced, the test principle and the indentation data analysis method were described. It was used to test the micro mechanical properties, such as hardness, elastic modulus and indentation creep property of n-Al2O3/Ni composite coating on steel prepared by brush plating, and the variety of mechanical properties with coating thickness was researched. The results show that the mechanical properties are basically identical within the whole coating, the hardness and modulus decrease in the defect fields, especially within the dendritic crystals, whereas the mechanical properties are not influenced greatly at the interspaces among dendritic crystals. The average hardness and elastic modulus of n-Al2O3/Ni coating are 6.34 GPa and 154 GPa respectively, and the hardness is 2.4 times higher than that of steel and the indentation creep curve of n-Al2O3/Ni coating is similar to that of the uniaxial compression creep, and the creep rate of steady-state is about 0. 104 nm/s. These results will supply useful data for process improvement, new type material development and application expansion.

Zinc Oxide Nano Particles Integrated Kenaf/Unsaturated Polyester BioComposite

Increasing need for materials with special features have brought various new inventions,one of the most promising hope for new material with special features and functionalities is composites materials.Thus,this study report an integration of zinc nanoparticles into kenaf/polyester polymer composite to introduce new behavior to the composite.The composite behaviors were compared for mechanical,thermal,moisture absorption and biodegradability properties.Prepared Zinc Oxide nanoparticles entrenched in the kenaf/polyestaer composites net structure through chemical bonds between kenaf/ZnO/polyester resin,existence of ZnO significantly influence the mechanical and thermals properties of composites.Thermal analysis based on(TGA)response revealed the integration of ZnO nanoparticles improved the thermal stability when thermal decomposition temperature beyond 3650 C.The thermal cracking decreased with present of ZnO and increase with kenaf content(layers).The modulus,Tensile strength,break at elongation,flexural modulus,flexural strength and impact strength of the composites with higher content kenaf/ZnO nanoparticle are 560 MPa,58MPa,1.8%,1300 PMa,68 MPa and 31 MPa,respectively.Thus,addition of kenaf layers and ZnO results in larger mechanical properties enhancement,the results of the contact angle show improvement in wetting of the fibres with addition of ZnO nanoparticles.

Synthesis and study of MPNS/SMA nano-composite tanning agent

The radical polymerization of maleic anhydride（MA）,styrene（ST）with the vinyl groups introduced onto the surface of the nano-sized silica via solution polymerization method was developed.The methacryloxypropyl nano-sized silica（MPNS）was used as macromonomer and polymerized with maleic anhydride and styrene by initiating with BPO in toluene.The structure and properties of MPNS/SMA nano-composite were characterized by FT-IR spectra and TEM.Meanwhile,it was applied as tanning agent compared with the traditional styrene-maleic anhydride copolymer in leather.It was found that the applied leather had better quality characteristics with the addition of the nano-sized silica.

Microstructure and Behaviors of Nano Composite Coating

Nano composite coatings are fabricated by electro brush plating containing various nano particles (A12O3, SiO2 and ZrO2>. Its surface morphology and microstructure are observed by means of S-2700 scanning electron microscopy (SEM). And the mechanical behaviors of nano composite coating are analyzed. The results show that microstructure of nano composite coating is obviously fine because of nano particles. Micro hardness at room temperature increases with the increase of nano particles content. The wear resistance and hardness at high temperature are also improved. The strengthening effect is differentiated by the type and content of nano particles. This is due to the combination of dispersion strengthening and grain size strengthening.

Effects of rare earth on microstructures and properties of Ni-W-P-CeO_2-SiO_2 nano-composite coatings

Ni-W-P-CeO2-SiO2 nano-composite coatings were prepared on common carbon steel surface by pulse electrodeposition of nickel, tungsten, phosphorus, rare earth （nano-CeO2） and silicon carbide （nano-SiO2） particles. The effects of nano-CeO2 concentrations in electrolyte on microstructures and properties of nano-composite coatings were studied. The samples were characterized with chemical compositions, elements distributions, microhardness and microstructures. The results indicated that when nano-CeO2 concentration was controlled at 10 g/L, the nano-composite coatings possessed higher microhardness and compact microstmctures with clear outline of spherical matrix metal crystallites, fine crystallite sizes and uniform distribution of elements W, P, Ce and Si within the Ni-W-P matrix metal. Increasing the nano-CeO2 particles concentrations from 4 to 10 g/L led to refinement in grain structure and improvement of microstructures, while when increased to 14 g/L, the crystallite sizes began to increase again and there were a lot of small boss with nodulation shape appearing on the nano-composite coatings surface.