ZrO2/TiO2 composite photocatalytic film was produced on the pure titanium substrate using in-situ Zr（OH）4 colloidal particle by the micro-arc oxidation technique and characterized by scanning electron microscope （...ZrO2/TiO2 composite photocatalytic film was produced on the pure titanium substrate using in-situ Zr（OH）4 colloidal particle by the micro-arc oxidation technique and characterized by scanning electron microscope （SEM）, energy dispersive X-ray （EDX）, X-ray diffraction （XRD） and ultraviolet-visible （UV-Vis） spectrophotometer. The composite film shows a lamellar and porous structure which consists of anatase, futile and ZrO2 phases. The optical absorption edge of film is shifted to longer wavelength when ZrO2 is introduced to TiO2. Furthermore, the photocatalytic reaction rate constants of degradation of rhodamine B solution with ZrO2/TiO2 composite film and pure TiO2 film under ultraviolet irradiation are measured as 0.0442 and 0.0186 h 1, respectively.展开更多
Series of TiO 2-ZnO heterojunction composite films with different n（Zn）/n（Ti） ratios were prepared by UDP450 magnetron sputter ion plating equipment, and the mole ratio of Zn to Ti was controlled by adjusting the ...Series of TiO 2-ZnO heterojunction composite films with different n（Zn）/n（Ti） ratios were prepared by UDP450 magnetron sputter ion plating equipment, and the mole ratio of Zn to Ti was controlled by adjusting the current values of sputtering target. The effects of n（Zn）/n（Ti） on the microstructures of TiO2-ZnO films were investigated by SEM, AFM, Raman and XPS, and their photocatalytic decomposition of methyl orange solutions was evaluated. The results show that an increase in n（Zn）/n（Ti） typically results in a decrease in the grain size of composite films firstly and then an increase of grain size, while an increase in n（Zn）/n（Ti） leads to an increase in film roughness firstly and then a decrease in film roughness. Both grain size and roughness of TiO2-ZnO films reach the maximum and minimum at n（Zn）/n（Ti） of 1/9.3, respectively. The n（Zn）/n（Ti） shows little effect on the valences of Zn and Ti elements, which mainly exist in the form of TiO2 and ZnO phases. The n（Zn）/n（Ti） has influence on the amount of anatase/rutile TiO2 heterojunction in the film. With increase of the n（Zn）/n（Ti）, the absorption intensity of the composite film increases and the absorption region extends to 450 nm, which is redshifted as much as 150 nm in comparison with the pure TiO2 films. However, the photocatalytic abilities of heterogeneous composite films do not depend on the n（Zn）/n（Ti） but rather on the microstructures of the TiO2-ZnO composite films. Degradation rate of the film reaches the maximum and the photocatalytic decomposition of pollutants works best when n（Zn）/n（Ti）=1：9.3.展开更多
Two kinds of TiO_2 nanometer thin films were prepared on stainless steel bythe reverse micellar and sol-gel methods, respectively. The calcined TiO_ 2 thin films werecharacterized by X-ray diffraction (XRD), atomic fo...Two kinds of TiO_2 nanometer thin films were prepared on stainless steel bythe reverse micellar and sol-gel methods, respectively. The calcined TiO_ 2 thin films werecharacterized by X-ray diffraction (XRD), atomic force microscopy (AFM), BET surface area and X-rayphotoelectron spectroscopy (XPS). Photocatalytic activity was evaluated by photocatalyticdecoloration of methyl orange aqueous solution. The results showed that the TiO_2 thin filmsprepared by reverse micellar method (designated as RM-TiO_2 films) showed higher photocatalyticactivity than those by sol-gel method (designated as SG-TiO_2 films). This is attributed to the factthat the former is composed of smaller monodispersed spherical particles with a size of about 15 nmand possesses higher surface areas.展开更多
Anatase TiO2 sol was synthesized under mild conditions （75℃ and ambient pressure） by hydrolysis of titaniumn-butoxide in abundant acidic aqueous solution and subsequent reflux to enhance crystallization. At room te...Anatase TiO2 sol was synthesized under mild conditions （75℃ and ambient pressure） by hydrolysis of titaniumn-butoxide in abundant acidic aqueous solution and subsequent reflux to enhance crystallization. At room temperature and in ambient atmosphere, crystalline TiO2 thin films were deposited on polymethylmethacrylate （PMMA）, SiO2-coated PMMA and SiO2-coated silicone rubber substrates from the as-prepared TiO2 sol by a dip-coating process. SiO2 layers prior to TiO2 thin films on polymer substrates could not only protect the substrates from the photocatalytic decomposition of the TiO2 thin films but also enhance the adhesion of the TiO2 thin films to the substrates. Field-emission type scanning electron microscope （FE-SEM） investigations revealed that the average particle sizes of the nanoparticles composing the TiO2 thin films were about 35-47 nm. The TiO2 thin films exhibited high photocatalytic activities in the degradation of reactive brilliant red dye X-3B in aqueous solution under aerated conditions. The preparation process of photocatalytic TiO2 thin films on the polymer substrates was quite simple and a low temperature route.展开更多
A new kind of porous nano-'IiO_2 composite films was prepared on the glasssubstrate with the water glass as binders and the sodium fluorosilicate as solidifying reagent. Themorphologies of the films were studied b...A new kind of porous nano-'IiO_2 composite films was prepared on the glasssubstrate with the water glass as binders and the sodium fluorosilicate as solidifying reagent. Themorphologies of the films were studied by scanning electron microscope(SEM).The UV-Visspcctiophotometer was also used to investigate the absorption of the films. The gas-phasephotocatalytic oxidation of nitrogen oxides on the composite film was carried out in Ti0_2/UVsystem, and some important factors affecting the photocatalytic oxidation were also studied such asthe catalyst concentration, vapor pressure and the presence of oxygen. The results showed theconversion of NO_x reached 97.5% alter 2 h UV-irradiation. The final product of photo-oxidation wasdetected to be HNO_3 by FT-IR. The way of photocatalytic oxidation of NO_x was possibly useful inthe practical application.展开更多
TiO2 thin films were prepared by DC magnetron sputtering with the oxygen flow rate higher than the threshold. The film deposited for 5 h was of anatase phase with a preferred orientation along the <220> directio...TiO2 thin films were prepared by DC magnetron sputtering with the oxygen flow rate higher than the threshold. The film deposited for 5 h was of anatase phase with a preferred orientation along the <220> direction, but the films deposited for 2 and 3 h were amorphous. The transmittance and photocatalytic activity of the TiO2 films increased constantly with increasing film thickness. When the annealing temperature was lower than 700℃, only anatase grew in the TiO2 film. TiO2 phase changed from anatase to rutile when the annealing temperature was above 800℃. The photocatalytic activity decreased with increasing annealing temperature.展开更多
To deposit TiO2 films through plasma CVD, the partial pressure ratio of O2 to TIC14 should be greater than the stoichiometric ratio （PO2/PTiCl4 〉 1）. However, this may lead to the formation of powder instead of fil...To deposit TiO2 films through plasma CVD, the partial pressure ratio of O2 to TIC14 should be greater than the stoichiometric ratio （PO2/PTiCl4 〉 1）. However, this may lead to the formation of powder instead of film on the substrate when using volume dielectric barrier discharge （volume-DBD） at atmospheric pressure. In this study, by adding N2 into the working gas Ar, TiO2 photocatalytic films were successfully fabricated in the presence of excess O2 （PO2/PTiC14 = 2.6） by using a wire-to-plate atmospheric-pressure volume-DBD. The tuning effect of N2 on the deposition of TiO2 film was studied in detail. The results showed that by increasing the N2 content, the deposition rate and particle size of the TiO2 film were reduced, and its photocatalytic activity was enhanced. The tuning mechanism of N2 is further discussed.展开更多
Nano-F-/Ce3+/TiO2 particles were prepared by hydrolysis of tetrabutyl titanate in a mixed CF3COOH-Ce(NO3)3-H2O solution. The photocatalytic decomposition of methylene blue in aqueous solution was used to evaluate thei...Nano-F-/Ce3+/TiO2 particles were prepared by hydrolysis of tetrabutyl titanate in a mixed CF3COOH-Ce(NO3)3-H2O solution. The photocatalytic decomposition of methylene blue in aqueous solution was used to evaluate their photocatalytic activities. The powders were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersion X-ray spectrum (EDS), and Brunauer-Emmett-Teller (BET) surface area analysis. The results showed that F- and Ce3+ were doped into TiO2. The appropriate content of fluorine and cerium were 2.0% and 1.0% (atom fraction) respectively. The codoped nano-F-/Ce3+/TiO2 particles had higher BET specific surface area, smaller crystallite size and higher photocatalytic activity than those of undoped TiO2 particles.展开更多
By the UV-curing method, a porous TiO2 film with net-like framework has been prepared. The characterization results of the porous TiO2 film by means of SEM, TEM, XRD, and N2 adsorption-desorption analysis show that th...By the UV-curing method, a porous TiO2 film with net-like framework has been prepared. The characterization results of the porous TiO2 film by means of SEM, TEM, XRD, and N2 adsorption-desorption analysis show that the net-like framework of the porous TiO2 film is composed of TiO2 nanoparticles, forming three dimensional porous structure. The porous TiO2 film exhibits higher photocatalytic activity for the degradation of methylene blue（MB） dye compared with the conventional dense TiO2 film.展开更多
In the present work, the hybrid catalyst films of TiO2/CuO containing up to 10% in mol of copper were deposited onto glass surface. Precursor solutions were obtained by citrate precursor method. Films were porous and ...In the present work, the hybrid catalyst films of TiO2/CuO containing up to 10% in mol of copper were deposited onto glass surface. Precursor solutions were obtained by citrate precursor method. Films were porous and the average particle size was 20 nm determined by FEG-SEM analysis. The photocatalytic activities of these films were studied using Rhodamine B as a target compound in a fixed bed reactor developed in our laboratory and UV lamp. It was observed that the addition of copper to TiO2 increased significantly its photocatalytic activity during the oxidation of Rhodamine B. The degradation exceeded 90% within 48 hours of irradiation compared to 38% when pure TiO2 was used. Moreover, there was a reduction in the particles band gap energy when compared to that of pure TiO2. These results indicate that the TiO2/CuO films are promising catalysts for the development of fixed bed reactors to be used to treat effluents containing azo dyes.展开更多
The uniform transparent TiO2/SiO2 photocatalytic composite thin films are prepared by sol-gel method on the soda lime glass substrates, and characterized by UV-visible spectroscopy, X-ray diffraction (XRD), transmissi...The uniform transparent TiO2/SiO2 photocatalytic composite thin films are prepared by sol-gel method on the soda lime glass substrates, and characterized by UV-visible spectroscopy, X-ray diffraction (XRD), transmission electron microscopy (TEM), BET surface area, FTIR spectroscopy and X-ray photoelectron spectroscopy (XPS). It was found that the addition of SiO2 to TiO2 thin films can suppress the grain growth of TiO2 crystal, increase the hydroxyl content on the surface of TiO2 films, lower the contact angle for water on TiO, films and enhance the hydrophilic property of TiO2 films. The super-hydrophilic TiO2/SiO2 photocatalytic composite thin films with the contact angle of 0((o) under bar) are obtained by the addition of 10%-20% SiO2 in mole fraction.展开更多
The feasibility of photocatalytic degradation of organochlorine compounds using TiO 2 supported on fiberglass cloth as a photocatalyst was studied. The results showed that 2 0×10 -4 mol/dm 3 of dichloroeth...The feasibility of photocatalytic degradation of organochlorine compounds using TiO 2 supported on fiberglass cloth as a photocatalyst was studied. The results showed that 2 0×10 -4 mol/dm 3 of dichloroethylene, trichloroethylene and tetrachloroethylene can be completely photocatalytically degraded within a short time under illumination with a 375W medium pressure mercury lamp. The effects of parameters such as illumination time, initial concentration of organochlorine compounds, amount of air flow and concentration of H 2O 2 on the photocatalytic degradation were investigated. The TiO 2 supported on the fiberglass was not easily detached and after 500h illumination there was no significant loss of photocatalytic activity of TiO 2. The passible mechanisms of photocatalytic degradation were discussed.展开更多
It is well known that the photocatalytic activity of TiO_2 thin filmsstrongly depends on the preparing methods and post-treatment conditions, since they have a decisiveinfluence on the chemical and physical properties...It is well known that the photocatalytic activity of TiO_2 thin filmsstrongly depends on the preparing methods and post-treatment conditions, since they have a decisiveinfluence on the chemical and physical properties of TiO_2 thin films. Therefore, it is necessary toelucidate the influence of the preparation process and post-treatment conditions on thephoto-catalytic activity and surface microstructures of the films. This review deals with thepreparation of TiO_2 thin film photo-catalysts by wet-chemical methods (such as sol-gel,-reversemicellar and liquid phase deposition) and the comparison of various preparation methods as well astheir advantage and disadvantage. Furthermore, it is discussed that the advancement ofphotocatalytic activity, super-hydrophilicity and bactericidal activity of TiO_2 thin filmphotocatalyst in recent years.展开更多
Ag TiO 2 thin films were prepared on glasses.The morphology and structure of Ag TiO 2 films were investigated by XRD, SEM and FT IR.The photocatalytic and hydrophilic properties of Ag TiO 2 thin films were also...Ag TiO 2 thin films were prepared on glasses.The morphology and structure of Ag TiO 2 films were investigated by XRD, SEM and FT IR.The photocatalytic and hydrophilic properties of Ag TiO 2 thin films were also evaluated by examining photocatalytic degradation dichlorophos under sunlight illumination and the change of contact angle respectively.The research results show that the Ag TiO 2 thin film is mainly composed of 20-100nm Ag and TiO 2 particles.The Ag TiO 2 thin films possess a super hydrophilic ability and higher photocatalytic activity than that of pure TiO 2 thin film.展开更多
The waterborne polyurethane/doped Ti O2 nanoparticle hybrid films were prepared. Nd, I doped Ti O2 was prepared with a 50 nm particle size firstly. The hybrid film was prepared by mixing doped Ti O2 with waterborne po...The waterborne polyurethane/doped Ti O2 nanoparticle hybrid films were prepared. Nd, I doped Ti O2 was prepared with a 50 nm particle size firstly. The hybrid film was prepared by mixing doped Ti O2 with waterborne polyurethane, followed by heat treatment. The presence and nanometric distribution of doped Ti O2 nanoparticles in prepared membranes is evident according to SEM images. The photocatalytic activities of doped Ti O2 were signifi cantly enhanced compared with pure Ti O2 powders. After the hybrid fi lm fabrication, the photocatalytic activities were almost the same as the pure catalysts with kMB of 0.046. In the antibacterial testing, the hybrid fi lms can inhibit E. coli growth. A signifi cant decrease in membrane fl uidity and increase of permeability of E. coli were observed.展开更多
The transparent C-doped TiO2 nanostructure films were fabricated on the silicate glass substrates by sol-gel spin-coated method. The as-prepared films were characterized by X-ray diffraction （XRD）, scanning electron...The transparent C-doped TiO2 nanostructure films were fabricated on the silicate glass substrates by sol-gel spin-coated method. The as-prepared films were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, UV-visible absorption spectra （UV-vis） and X-ray photoelectron spectroscopy （XPS）. The photocatalytic activity was evaluated via the photocatalytic oxidation of methylene blue in aqueous under daylight irradiation at room temperature. The results show that the daylight-induced photocatalytic activities of the as-prepared films are improved by the C-doping. The calcination temperatures significantly affect the morphology, microstructure and photocatalytic activity of the as-prepared samples. At 723 K, the C-doped TiO2 films exhibit the highest photocatalytic activity due to the synergetic effects of good crystallization, appropriate oxygen vacancies and strong absorption in the near UV and visible-light region.展开更多
基金Project(gf200901002)supported by the Open Research Fund of National Defense Key Disciplines Laboratory of Light Alloy Processing Science and Technology of Nanchang Hangkong University,China
文摘ZrO2/TiO2 composite photocatalytic film was produced on the pure titanium substrate using in-situ Zr（OH）4 colloidal particle by the micro-arc oxidation technique and characterized by scanning electron microscope （SEM）, energy dispersive X-ray （EDX）, X-ray diffraction （XRD） and ultraviolet-visible （UV-Vis） spectrophotometer. The composite film shows a lamellar and porous structure which consists of anatase, futile and ZrO2 phases. The optical absorption edge of film is shifted to longer wavelength when ZrO2 is introduced to TiO2. Furthermore, the photocatalytic reaction rate constants of degradation of rhodamine B solution with ZrO2/TiO2 composite film and pure TiO2 film under ultraviolet irradiation are measured as 0.0442 and 0.0186 h 1, respectively.
基金Project (2010JQ6008) supported by the Natural Science Foundation of Shaanxi Province,China
文摘Series of TiO 2-ZnO heterojunction composite films with different n（Zn）/n（Ti） ratios were prepared by UDP450 magnetron sputter ion plating equipment, and the mole ratio of Zn to Ti was controlled by adjusting the current values of sputtering target. The effects of n（Zn）/n（Ti） on the microstructures of TiO2-ZnO films were investigated by SEM, AFM, Raman and XPS, and their photocatalytic decomposition of methyl orange solutions was evaluated. The results show that an increase in n（Zn）/n（Ti） typically results in a decrease in the grain size of composite films firstly and then an increase of grain size, while an increase in n（Zn）/n（Ti） leads to an increase in film roughness firstly and then a decrease in film roughness. Both grain size and roughness of TiO2-ZnO films reach the maximum and minimum at n（Zn）/n（Ti） of 1/9.3, respectively. The n（Zn）/n（Ti） shows little effect on the valences of Zn and Ti elements, which mainly exist in the form of TiO2 and ZnO phases. The n（Zn）/n（Ti） has influence on the amount of anatase/rutile TiO2 heterojunction in the film. With increase of the n（Zn）/n（Ti）, the absorption intensity of the composite film increases and the absorption region extends to 450 nm, which is redshifted as much as 150 nm in comparison with the pure TiO2 films. However, the photocatalytic abilities of heterogeneous composite films do not depend on the n（Zn）/n（Ti） but rather on the microstructures of the TiO2-ZnO composite films. Degradation rate of the film reaches the maximum and the photocatalytic decomposition of pollutants works best when n（Zn）/n（Ti）=1：9.3.
基金This project is financially supported by the National Natural Science Foundation of China (No.s 50272049, 50072016) The Excellent Young Teachers Program of MOE, China (No. (2002)350)
文摘Two kinds of TiO_2 nanometer thin films were prepared on stainless steel bythe reverse micellar and sol-gel methods, respectively. The calcined TiO_ 2 thin films werecharacterized by X-ray diffraction (XRD), atomic force microscopy (AFM), BET surface area and X-rayphotoelectron spectroscopy (XPS). Photocatalytic activity was evaluated by photocatalyticdecoloration of methyl orange aqueous solution. The results showed that the TiO_2 thin filmsprepared by reverse micellar method (designated as RM-TiO_2 films) showed higher photocatalyticactivity than those by sol-gel method (designated as SG-TiO_2 films). This is attributed to the factthat the former is composed of smaller monodispersed spherical particles with a size of about 15 nmand possesses higher surface areas.
文摘Anatase TiO2 sol was synthesized under mild conditions （75℃ and ambient pressure） by hydrolysis of titaniumn-butoxide in abundant acidic aqueous solution and subsequent reflux to enhance crystallization. At room temperature and in ambient atmosphere, crystalline TiO2 thin films were deposited on polymethylmethacrylate （PMMA）, SiO2-coated PMMA and SiO2-coated silicone rubber substrates from the as-prepared TiO2 sol by a dip-coating process. SiO2 layers prior to TiO2 thin films on polymer substrates could not only protect the substrates from the photocatalytic decomposition of the TiO2 thin films but also enhance the adhesion of the TiO2 thin films to the substrates. Field-emission type scanning electron microscope （FE-SEM） investigations revealed that the average particle sizes of the nanoparticles composing the TiO2 thin films were about 35-47 nm. The TiO2 thin films exhibited high photocatalytic activities in the degradation of reactive brilliant red dye X-3B in aqueous solution under aerated conditions. The preparation process of photocatalytic TiO2 thin films on the polymer substrates was quite simple and a low temperature route.
基金Supported by the Key Technologies Research and Development Programme of the Ninth Five year Plan of China (96 554 03 01)
文摘A new kind of porous nano-'IiO_2 composite films was prepared on the glasssubstrate with the water glass as binders and the sodium fluorosilicate as solidifying reagent. Themorphologies of the films were studied by scanning electron microscope(SEM).The UV-Visspcctiophotometer was also used to investigate the absorption of the films. The gas-phasephotocatalytic oxidation of nitrogen oxides on the composite film was carried out in Ti0_2/UVsystem, and some important factors affecting the photocatalytic oxidation were also studied such asthe catalyst concentration, vapor pressure and the presence of oxygen. The results showed theconversion of NO_x reached 97.5% alter 2 h UV-irradiation. The final product of photo-oxidation wasdetected to be HNO_3 by FT-IR. The way of photocatalytic oxidation of NO_x was possibly useful inthe practical application.
基金supported by the National Natural Science Foundation of China(No.50001013)Hundred-Talent Project of CAS and the NSFC for Outstanding Young Scientists(No.59625103).
文摘TiO2 thin films were prepared by DC magnetron sputtering with the oxygen flow rate higher than the threshold. The film deposited for 5 h was of anatase phase with a preferred orientation along the <220> direction, but the films deposited for 2 and 3 h were amorphous. The transmittance and photocatalytic activity of the TiO2 films increased constantly with increasing film thickness. When the annealing temperature was lower than 700℃, only anatase grew in the TiO2 film. TiO2 phase changed from anatase to rutile when the annealing temperature was above 800℃. The photocatalytic activity decreased with increasing annealing temperature.
基金supported by National Natural Science Foundation of China(Nos.10835004,51077009)the Fundamental Research Funds for the Central Universities
文摘To deposit TiO2 films through plasma CVD, the partial pressure ratio of O2 to TIC14 should be greater than the stoichiometric ratio （PO2/PTiCl4 〉 1）. However, this may lead to the formation of powder instead of film on the substrate when using volume dielectric barrier discharge （volume-DBD） at atmospheric pressure. In this study, by adding N2 into the working gas Ar, TiO2 photocatalytic films were successfully fabricated in the presence of excess O2 （PO2/PTiC14 = 2.6） by using a wire-to-plate atmospheric-pressure volume-DBD. The tuning effect of N2 on the deposition of TiO2 film was studied in detail. The results showed that by increasing the N2 content, the deposition rate and particle size of the TiO2 film were reduced, and its photocatalytic activity was enhanced. The tuning mechanism of N2 is further discussed.
基金the Natural Science Foundation of Hebei Province (203364)the Natural Science Foundation of Hebei University of Science and Technology (XL2006038)
文摘Nano-F-/Ce3+/TiO2 particles were prepared by hydrolysis of tetrabutyl titanate in a mixed CF3COOH-Ce(NO3)3-H2O solution. The photocatalytic decomposition of methylene blue in aqueous solution was used to evaluate their photocatalytic activities. The powders were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersion X-ray spectrum (EDS), and Brunauer-Emmett-Teller (BET) surface area analysis. The results showed that F- and Ce3+ were doped into TiO2. The appropriate content of fluorine and cerium were 2.0% and 1.0% (atom fraction) respectively. The codoped nano-F-/Ce3+/TiO2 particles had higher BET specific surface area, smaller crystallite size and higher photocatalytic activity than those of undoped TiO2 particles.
基金Supported by the National Natural Science Foundation of China(Nos.20606035, 20401015, 50574082)Chinese Acade-my of Sciences Project of One Hundred Talents.
文摘By the UV-curing method, a porous TiO2 film with net-like framework has been prepared. The characterization results of the porous TiO2 film by means of SEM, TEM, XRD, and N2 adsorption-desorption analysis show that the net-like framework of the porous TiO2 film is composed of TiO2 nanoparticles, forming three dimensional porous structure. The porous TiO2 film exhibits higher photocatalytic activity for the degradation of methylene blue（MB） dye compared with the conventional dense TiO2 film.
基金FAPESP,FAPEMIG,CAPES and CNPq for the financial support.
文摘In the present work, the hybrid catalyst films of TiO2/CuO containing up to 10% in mol of copper were deposited onto glass surface. Precursor solutions were obtained by citrate precursor method. Films were porous and the average particle size was 20 nm determined by FEG-SEM analysis. The photocatalytic activities of these films were studied using Rhodamine B as a target compound in a fixed bed reactor developed in our laboratory and UV lamp. It was observed that the addition of copper to TiO2 increased significantly its photocatalytic activity during the oxidation of Rhodamine B. The degradation exceeded 90% within 48 hours of irradiation compared to 38% when pure TiO2 was used. Moreover, there was a reduction in the particles band gap energy when compared to that of pure TiO2. These results indicate that the TiO2/CuO films are promising catalysts for the development of fixed bed reactors to be used to treat effluents containing azo dyes.
基金This work was financially supported by the Foundation for University Key Teachers by the Ministry of Education, theKey Resear
文摘The uniform transparent TiO2/SiO2 photocatalytic composite thin films are prepared by sol-gel method on the soda lime glass substrates, and characterized by UV-visible spectroscopy, X-ray diffraction (XRD), transmission electron microscopy (TEM), BET surface area, FTIR spectroscopy and X-ray photoelectron spectroscopy (XPS). It was found that the addition of SiO2 to TiO2 thin films can suppress the grain growth of TiO2 crystal, increase the hydroxyl content on the surface of TiO2 films, lower the contact angle for water on TiO, films and enhance the hydrophilic property of TiO2 films. The super-hydrophilic TiO2/SiO2 photocatalytic composite thin films with the contact angle of 0((o) under bar) are obtained by the addition of 10%-20% SiO2 in mole fraction.
文摘The feasibility of photocatalytic degradation of organochlorine compounds using TiO 2 supported on fiberglass cloth as a photocatalyst was studied. The results showed that 2 0×10 -4 mol/dm 3 of dichloroethylene, trichloroethylene and tetrachloroethylene can be completely photocatalytically degraded within a short time under illumination with a 375W medium pressure mercury lamp. The effects of parameters such as illumination time, initial concentration of organochlorine compounds, amount of air flow and concentration of H 2O 2 on the photocatalytic degradation were investigated. The TiO 2 supported on the fiberglass was not easily detached and after 500h illumination there was no significant loss of photocatalytic activity of TiO 2. The passible mechanisms of photocatalytic degradation were discussed.
文摘It is well known that the photocatalytic activity of TiO_2 thin filmsstrongly depends on the preparing methods and post-treatment conditions, since they have a decisiveinfluence on the chemical and physical properties of TiO_2 thin films. Therefore, it is necessary toelucidate the influence of the preparation process and post-treatment conditions on thephoto-catalytic activity and surface microstructures of the films. This review deals with thepreparation of TiO_2 thin film photo-catalysts by wet-chemical methods (such as sol-gel,-reversemicellar and liquid phase deposition) and the comparison of various preparation methods as well astheir advantage and disadvantage. Furthermore, it is discussed that the advancement ofphotocatalytic activity, super-hydrophilicity and bactericidal activity of TiO_2 thin filmphotocatalyst in recent years.
文摘Ag TiO 2 thin films were prepared on glasses.The morphology and structure of Ag TiO 2 films were investigated by XRD, SEM and FT IR.The photocatalytic and hydrophilic properties of Ag TiO 2 thin films were also evaluated by examining photocatalytic degradation dichlorophos under sunlight illumination and the change of contact angle respectively.The research results show that the Ag TiO 2 thin film is mainly composed of 20-100nm Ag and TiO 2 particles.The Ag TiO 2 thin films possess a super hydrophilic ability and higher photocatalytic activity than that of pure TiO 2 thin film.
基金Funded by the National Natural Science Foundation of China(No.51208141)Open Project of State Key Laboratory of Urban Water Resource and Environment,Harbin Institute of Technology(No.QA201206)
文摘The waterborne polyurethane/doped Ti O2 nanoparticle hybrid films were prepared. Nd, I doped Ti O2 was prepared with a 50 nm particle size firstly. The hybrid film was prepared by mixing doped Ti O2 with waterborne polyurethane, followed by heat treatment. The presence and nanometric distribution of doped Ti O2 nanoparticles in prepared membranes is evident according to SEM images. The photocatalytic activities of doped Ti O2 were signifi cantly enhanced compared with pure Ti O2 powders. After the hybrid fi lm fabrication, the photocatalytic activities were almost the same as the pure catalysts with kMB of 0.046. In the antibacterial testing, the hybrid fi lms can inhibit E. coli growth. A signifi cant decrease in membrane fl uidity and increase of permeability of E. coli were observed.
基金Funded by Shan Xi Research Fund for Returned Scholars (No.2007-25)Shan Xi Open Fund for Key Laboratory(No.2008012013-7)The Specialized Fund for The Innovative of College Students of Tai Yuan City(No.09122018)
文摘The transparent C-doped TiO2 nanostructure films were fabricated on the silicate glass substrates by sol-gel spin-coated method. The as-prepared films were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, UV-visible absorption spectra （UV-vis） and X-ray photoelectron spectroscopy （XPS）. The photocatalytic activity was evaluated via the photocatalytic oxidation of methylene blue in aqueous under daylight irradiation at room temperature. The results show that the daylight-induced photocatalytic activities of the as-prepared films are improved by the C-doping. The calcination temperatures significantly affect the morphology, microstructure and photocatalytic activity of the as-prepared samples. At 723 K, the C-doped TiO2 films exhibit the highest photocatalytic activity due to the synergetic effects of good crystallization, appropriate oxygen vacancies and strong absorption in the near UV and visible-light region.
