A mixture of amorphous carbon and carbon nanotubes films was synthesized on stainless steel plates by a micro- wave plasma enhanced chemical vapor deposition system. The source gases were hydrogen and methane with flo...A mixture of amorphous carbon and carbon nanotubes films was synthesized on stainless steel plates by a micro- wave plasma enhanced chemical vapor deposition system. The source gases were hydrogen and methane with flow rates of 100 and 16sccm,respectively,with a total pressure of 5.0kPa. The surface morphology and the structure of the films were characterized by field emission scanning electron microscopy （SEM） and Raman scattering spectroscopy. Field emission properties of as-deposited film were measured in a vacuum room below 5 ×10^ 5 Pa. The experimental results show that the initial turn-on field is 0. 9V/μm; The current density is 4.0mA/cm2 and the emission sites are dense and uniform at an electric field of 3.7V/μm. These results indicate that such a mixture of amorphous carbon and carbon nanotubes films is a promising material for field emission applications.展开更多
This paper reported that the nano-catkin carbon films were prepared on Si substrates by means of electron cyclotron resonance microwave plasma chemical vapour deposition in a hydrogen and methane mixture. The surface ...This paper reported that the nano-catkin carbon films were prepared on Si substrates by means of electron cyclotron resonance microwave plasma chemical vapour deposition in a hydrogen and methane mixture. The surface morphology and the structure of the fabricated films were characterized by using scanning electron microscopes and Raman spectroscopy, respectively. The stable field emission properties with a low threshold field of 5V/μm corresponding to a current density of about 1μA/cm^2 and a current density of 3.2mA/cm^2 at an electric field of 10V/μm were obtained from the carbon film deposited at CH4 concentration of 8%. The mechanism that the threshold field decreased with the increase of the CH4 concentration and the high emission current appeared at the high CH4 concentration was explained by using the Fowler-Nordheim theory.展开更多
A simple process to fabricate chain-like carbon nanotube （CNT） films by microwave plasma-enhanced chemical vapor deposition （MPCVD） was developed successfully. Prior to deposition, the Ti/Al2O3 substrates were gro...A simple process to fabricate chain-like carbon nanotube （CNT） films by microwave plasma-enhanced chemical vapor deposition （MPCVD） was developed successfully. Prior to deposition, the Ti/Al2O3 substrates were ground with Fe-doped SiO2 powder. The nano-structure of the deposited films was analyzed by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, and Raman spectroscopy. The field electron emission characteristics of the chain-like carbon nanotube films were measured under the vacuum of 10-5 Pa. The low turn-on field of 0.80 V/μm and the emission current density of 8.5 mA/cm2 at the electric field of 3.0 V/μm are obtained. Based on the above results, chain-like carbon nanotube films probably have important applications in cold cathode materials and electrode materials.展开更多
This paper reports that the nano-sheet carbon films （NSCFs） were fabricated on Si wafer chips with hydrogen- methane gas mixture by means of quartz-tube-type microwave plasma chemical vapour deposition （MWPCVD）. I...This paper reports that the nano-sheet carbon films （NSCFs） were fabricated on Si wafer chips with hydrogen- methane gas mixture by means of quartz-tube-type microwave plasma chemical vapour deposition （MWPCVD）. In order to further improve the field emission （FE） characteristics, a 5-nm Au film was prepared on the samples by using electron beam evaporation. The FE properties were obviously improved due to depositing Au thin film on NSCFs. The FE current density at a macroscopic electric field, E, of 9 V/μm was increased from 12.4 mA/cm2 to 27.2 mA/cm2 and the threshold field was decreased from 2.6 V/μm to 2.0 V/μm for Au-coated carbon films. A modified F-N model considering statistic effects of FE tip structures in the low E region and a space-chavge-limited-current effect in the high E region were applied successfully to explain the FE data of the Au-coated NSCF.展开更多
Nano-sheet carbon films are prepared on Si wafers by means of quartz-tube microwave plasma chemical vapour deposition （MPCVD） in a gas mixture of hydrogen and methane. The structure of the fabricated films is invest...Nano-sheet carbon films are prepared on Si wafers by means of quartz-tube microwave plasma chemical vapour deposition （MPCVD） in a gas mixture of hydrogen and methane. The structure of the fabricated films is investigated by using field emission scanning electron microscope （FESEM） and Raman spectroscopy. These nano^carbon films are possessed of good field emission （FE） characteristics with a low threshold field of 2.6 V/μm and a high current density of 12.6 mA/cm^2 at an electric field of 9 V/μm. As the FE currents tend to be saturated in a high E region, no simple Fowler-Nordheim （F-N） model is applicable. A modified F N model considering statistic effects of FE tip structures and a space-charge-limited-current （SCLC） effect is applied successfully to explaining the FE data observed at low and high electric fields, respectively.展开更多
The initial field electron emission degradation behaviour of original nano-structured sp^2-bonded amorphous carbon films has been observed, which can be attributed to the increase of the work function of the film in t...The initial field electron emission degradation behaviour of original nano-structured sp^2-bonded amorphous carbon films has been observed, which can be attributed to the increase of the work function of the film in the field emission process analysed using a Fowler-Nordheim plot. The possible reason for the change of work function is suggested to be the desorption of hydrogen from the original hydrogen termination film surface due to field emission current-induced local heating. For the explanation of the emission degradation behaviour of the nano-structured sp2-bonded amorphous carbon film, a cluster model with a series of graphite （0001） basal surfaces has been presented, and the theoretical calculations have been performed to investigate work functions of graphite （0001） surfaces with different hydrogen atom and ion chemisorption sites by using first principles method based on density functional theory-local density approximation.展开更多
The field emission （FE） characteristics of nano-structured carbon films （NSCFs） are investigated. The saturation behaviour of the field emission current density found at high electric field E cannot be reasonably ...The field emission （FE） characteristics of nano-structured carbon films （NSCFs） are investigated. The saturation behaviour of the field emission current density found at high electric field E cannot be reasonably explained by the traditional Fowler-Nordheim （F-N） theory. A three-region E model and the curve-fitting method are utilized for discussing the FE characteristics of NSCFs. In the low, high, and middle E regions, the FE mechanism is reasonably explained by a modified F-N model, a corrected space-charge-limited-current （SCLC） model and the joint model of F N and SCLC mechanism, respectively. Moreover, the measured FE data accord well with the results from our corrected theoretical model.展开更多
A fringelike field emission with high-luminescence and stable emission current from screen-printed carbon nanotube mixed zinc oxide (CNT-ZnO) composite cathode was investigated. The luminescent patterns are significan...A fringelike field emission with high-luminescence and stable emission current from screen-printed carbon nanotube mixed zinc oxide (CNT-ZnO) composite cathode was investigated. The luminescent patterns are significantly different from those observed in the field emission measure of pure CNT cathode. SEM images reveal that the CNTs are perfectly matched with ZnO powders by filling the interspaces in CNT film. XRD analysis demonstrates that the CNTs and ZnO have a high degree of crystalline perfection. Field emission measurement exhibits that the turn-on field of CNT-ZnO cathode is 2.08 V/μm, lower than 2.46 V/μm for pure CNT cathode. The large fringelike emission current at the brims of CNT-ZnO cathode is attributed to a combination of the increased effective contact area of CNTs, which decrease the sheet resistance of cathode film, and the dangled CNT bundles at the brims of CNT-ZnO film cathode.展开更多
Amorphous carbon nanoparticles （a-CNPs） on a multi-walled carbon nanotube （MWCNT） film, deposited on a silicon substrate, were synthesized using an electrodeposition combination from a methanol suspension of polyd...Amorphous carbon nanoparticles （a-CNPs） on a multi-walled carbon nanotube （MWCNT） film, deposited on a silicon substrate, were synthesized using an electrodeposition combination from a methanol suspension of polydiallyldimethylammonium chloride-modified MWCNTs. A low-voltage electropho- retic deposition of the MWCNTs and a high-voltage electrochemical deposition of the a-CNPs were carried out to yield homogenously attached a-CNPs on the surfaces of the MWCNTs, and form a composite film with good adhesion to the substrate. This scalable technology can produce a large area of a-CNP/MWCNT film. And the field emission investigations show that the a-CNP/MWCNT film has turn- on electric field of 3.17 V μm- 1 （at 10 μA cm-2） and threshold field of 4.62 V μm-1 （at 1 mA cm-2）, which are lower than those of the MWCNT film. The a-CNP/MWCNT film can be deposited simply with large areas and may be a promising cathode material applied in field emission displays.展开更多
文摘A mixture of amorphous carbon and carbon nanotubes films was synthesized on stainless steel plates by a micro- wave plasma enhanced chemical vapor deposition system. The source gases were hydrogen and methane with flow rates of 100 and 16sccm,respectively,with a total pressure of 5.0kPa. The surface morphology and the structure of the films were characterized by field emission scanning electron microscopy （SEM） and Raman scattering spectroscopy. Field emission properties of as-deposited film were measured in a vacuum room below 5 ×10^ 5 Pa. The experimental results show that the initial turn-on field is 0. 9V/μm; The current density is 4.0mA/cm2 and the emission sites are dense and uniform at an electric field of 3.7V/μm. These results indicate that such a mixture of amorphous carbon and carbon nanotubes films is a promising material for field emission applications.
文摘This paper reported that the nano-catkin carbon films were prepared on Si substrates by means of electron cyclotron resonance microwave plasma chemical vapour deposition in a hydrogen and methane mixture. The surface morphology and the structure of the fabricated films were characterized by using scanning electron microscopes and Raman spectroscopy, respectively. The stable field emission properties with a low threshold field of 5V/μm corresponding to a current density of about 1μA/cm^2 and a current density of 3.2mA/cm^2 at an electric field of 10V/μm were obtained from the carbon film deposited at CH4 concentration of 8%. The mechanism that the threshold field decreased with the increase of the CH4 concentration and the high emission current appeared at the high CH4 concentration was explained by using the Fowler-Nordheim theory.
文摘A simple process to fabricate chain-like carbon nanotube （CNT） films by microwave plasma-enhanced chemical vapor deposition （MPCVD） was developed successfully. Prior to deposition, the Ti/Al2O3 substrates were ground with Fe-doped SiO2 powder. The nano-structure of the deposited films was analyzed by scanning electron microscopy （SEM）, transmission electron microscopy （TEM）, and Raman spectroscopy. The field electron emission characteristics of the chain-like carbon nanotube films were measured under the vacuum of 10-5 Pa. The low turn-on field of 0.80 V/μm and the emission current density of 8.5 mA/cm2 at the electric field of 3.0 V/μm are obtained. Based on the above results, chain-like carbon nanotube films probably have important applications in cold cathode materials and electrode materials.
文摘This paper reports that the nano-sheet carbon films （NSCFs） were fabricated on Si wafer chips with hydrogen- methane gas mixture by means of quartz-tube-type microwave plasma chemical vapour deposition （MWPCVD）. In order to further improve the field emission （FE） characteristics, a 5-nm Au film was prepared on the samples by using electron beam evaporation. The FE properties were obviously improved due to depositing Au thin film on NSCFs. The FE current density at a macroscopic electric field, E, of 9 V/μm was increased from 12.4 mA/cm2 to 27.2 mA/cm2 and the threshold field was decreased from 2.6 V/μm to 2.0 V/μm for Au-coated carbon films. A modified F-N model considering statistic effects of FE tip structures in the low E region and a space-chavge-limited-current effect in the high E region were applied successfully to explain the FE data of the Au-coated NSCF.
文摘Nano-sheet carbon films are prepared on Si wafers by means of quartz-tube microwave plasma chemical vapour deposition （MPCVD） in a gas mixture of hydrogen and methane. The structure of the fabricated films is investigated by using field emission scanning electron microscope （FESEM） and Raman spectroscopy. These nano^carbon films are possessed of good field emission （FE） characteristics with a low threshold field of 2.6 V/μm and a high current density of 12.6 mA/cm^2 at an electric field of 9 V/μm. As the FE currents tend to be saturated in a high E region, no simple Fowler-Nordheim （F-N） model is applicable. A modified F N model considering statistic effects of FE tip structures and a space-charge-limited-current （SCLC） effect is applied successfully to explaining the FE data observed at low and high electric fields, respectively.
文摘The initial field electron emission degradation behaviour of original nano-structured sp^2-bonded amorphous carbon films has been observed, which can be attributed to the increase of the work function of the film in the field emission process analysed using a Fowler-Nordheim plot. The possible reason for the change of work function is suggested to be the desorption of hydrogen from the original hydrogen termination film surface due to field emission current-induced local heating. For the explanation of the emission degradation behaviour of the nano-structured sp2-bonded amorphous carbon film, a cluster model with a series of graphite （0001） basal surfaces has been presented, and the theoretical calculations have been performed to investigate work functions of graphite （0001） surfaces with different hydrogen atom and ion chemisorption sites by using first principles method based on density functional theory-local density approximation.
基金Project supported by the National Natural Science Foundation of China (Grant No. 11164031)the Scientific Research Foundation for the Returned Overseas Chinese Scholars,Ministry of Education of China (Grant No. (2009)1341)
文摘The field emission （FE） characteristics of nano-structured carbon films （NSCFs） are investigated. The saturation behaviour of the field emission current density found at high electric field E cannot be reasonably explained by the traditional Fowler-Nordheim （F-N） theory. A three-region E model and the curve-fitting method are utilized for discussing the FE characteristics of NSCFs. In the low, high, and middle E regions, the FE mechanism is reasonably explained by a modified F-N model, a corrected space-charge-limited-current （SCLC） model and the joint model of F N and SCLC mechanism, respectively. Moreover, the measured FE data accord well with the results from our corrected theoretical model.
文摘A fringelike field emission with high-luminescence and stable emission current from screen-printed carbon nanotube mixed zinc oxide (CNT-ZnO) composite cathode was investigated. The luminescent patterns are significantly different from those observed in the field emission measure of pure CNT cathode. SEM images reveal that the CNTs are perfectly matched with ZnO powders by filling the interspaces in CNT film. XRD analysis demonstrates that the CNTs and ZnO have a high degree of crystalline perfection. Field emission measurement exhibits that the turn-on field of CNT-ZnO cathode is 2.08 V/μm, lower than 2.46 V/μm for pure CNT cathode. The large fringelike emission current at the brims of CNT-ZnO cathode is attributed to a combination of the increased effective contact area of CNTs, which decrease the sheet resistance of cathode film, and the dangled CNT bundles at the brims of CNT-ZnO film cathode.
基金support from the Top Hundred Talents Program of Chinese Academy of Sciencesthe National Nature Science Foundation of China(No.51002161)
文摘Amorphous carbon nanoparticles （a-CNPs） on a multi-walled carbon nanotube （MWCNT） film, deposited on a silicon substrate, were synthesized using an electrodeposition combination from a methanol suspension of polydiallyldimethylammonium chloride-modified MWCNTs. A low-voltage electropho- retic deposition of the MWCNTs and a high-voltage electrochemical deposition of the a-CNPs were carried out to yield homogenously attached a-CNPs on the surfaces of the MWCNTs, and form a composite film with good adhesion to the substrate. This scalable technology can produce a large area of a-CNP/MWCNT film. And the field emission investigations show that the a-CNP/MWCNT film has turn- on electric field of 3.17 V μm- 1 （at 10 μA cm-2） and threshold field of 4.62 V μm-1 （at 1 mA cm-2）, which are lower than those of the MWCNT film. The a-CNP/MWCNT film can be deposited simply with large areas and may be a promising cathode material applied in field emission displays.
