Adhesion property of AlCrNbSiTi high-entropy alloy coating on zirconium:experimental and theoretical studies

Experimental scratch tests and first-principles calculations were used to investigate the adhesion property of AlCrNbSiTi high-entropy alloy(HEA)coatings on zirconium substrates.AlCrNbSiTi HEA and Cr coatings were deposited on Zr alloy substrates using multi-arc ion plating technology,and scratch tests were subsequently conducted to estimate the adhesion property of the coatings.The results indicated that Cr coatings had better adhesion strength than HEA coatings,and the HEA coatings showed brittleness.The special quasi-random structure approach was used to build HEA models,and Cr/Zr and HEA/Zr interface models were employed to investigate the cohesion between the coatings and Zr substrate using first-principles calculations.The calculated interface energies showed that the cohesion between the Cr coating and the Zr substrate was stronger than that of the HEA coating with Zr.In contrary to Al or Si in the HEA coating,Cr,Nb,and Ti atoms binded strongly with Zr substrate.Based on the calculated elastic constants,it was found that low Cr and high Al content decreased the mechanical performances of HEA coatings.Finally,this study demonstrated the utilization of a combined approach involving first-principles calculations and experimental studies for future HEA coating development.

Effect of Multiple Coatings of One-step Self-etching Adhesive on Microtensile Bond Strength to Primary Dentin

Objective To investigate the effect of multiple coatings of the one-step self-etching adhesive on immediate microtensile bond strength to primary dentin.Methods Twelve caries-free human primary molars were randomly divided into 2 groups with 6 teeth each.In group 1,each tooth was hemisected into two halves.One half was assigned to control subgroup 1,which was bonded with a single-step self-etching adhesive according to the manufacturer's instructions;the other half was assigned to experimental subgroup 1 in which the adhesive was applied three times before light curing.In group 2,the teeth were also hemisected into two halves.One half was assigned to control subgroup 2,which was bonded with the single-step self-etching adhesive according to the manufacturer's instructions;the other half was assigned to experimental subgroup 2 in which three layers of adhesive were applied with light curing each successive layer.Microtensile bond strength was immediately tested after specimen preparation.Results When the adhesive was applied three times before light curing,the bond strength of the experimental subgroup 1(n=33,57.49±11.61 MPa) was higher than that of the control subgroup 1(n=31,49.71±11.43 MPa,P<0.05).When using the technique of applying multiple layers of adhesive with light curing each successive layer,no difference of immediate bond strength was observed between the control subgroup 2 and the experimental subgroup 2(P>0.05).Conclusion Multiple coatings of one-step self-etching adhesive can increase the immediate bond strength to primary dentin when using the technique of light-curing after applying three layers of adhesive.

Microstructures and Adhesive Strength of Three Kinds of Ceramic Coatings

In gas turbine engine, the study of ceramic thermal resistance coating has always been paid more attention because it can effectively reduce metal interface temperatures, improve corrosion and/or oxidation resistance and extend life. The microstructures, SEM microfractographs and adhesive strength of three kinds of zirconia plasma-sprayed ceramic coating were investigated. The results indicated that nanostructured zirconia coating have higher adhesive strength and better micro-cracking resistance properties compared with magnesia or yttria stabilized zirconia coating because its less quantities laminar internal structures and closed packed structures with less quantities and uniform distribution cavities. The sprayed power is also an important factor affecting adhesive strength of nanostructured zirconia coating.

Adhesive strength and structure of micro-arc oxidation ceramic coatings grown in-situ on LY12 aluminum alloy

The ceramic coatings containing zirconium dioxide were grown in-situ on LY12 aluminium alloy by micro-arc oxidation in mixed zirconate and phosphate solution. The phase composition and morphology of the coatings were studied by XRD and SEM. The adhesive strength of ceramic coatings was assessed by thermal shock test and tensile test. The results show that the coating is composed of m-ZrO2,t-ZrO2, and a littleγ-Al2O3. Along the section of the coating, t-ZrO2 is more on both sides than that in the middle, while m-ZrO2 is more in the middle than that on both sides. Meantime the coating is also composed of a dense layer and a loose layer. The coating has excellent thermal shock resistance under 550℃and 600℃. And tensile tests show the adhesive strength of the dense layer of the coating with the substrate is more than 17.5 MPa.

Multiple Coatings can Improve the Bond Durability of One-step Self-etching Adhesive to Primary Dentin

Objective To investigate whether multiple coatings can improve the bond durability of one-step self-etching adhesive to primary dentin. Methods Twelve caries-free human primary molars were randomly divided into 2 groups. In group 1, each tooth was hemisected into 2 halves. One half was assigned to the control subgroup 1, which was bonded with a commercially available one-step self-etching adhesive according to the manufacturer＇s instruc- tions; the other half was assigned to experimental subgroup 1, in which the adhesive was applied three times before light curing. In group 2, one split half tooth was bonded with a commercially available one-step self-etching adhesive according to the manufacturer＇s instructions; for the other half, three layers of adhesive were applied with each successive layer of light curing. Specimens were stored in 0.9% NaC1 containing 0.02% sodium azide at 37℃ for 18 months and then were subjected to microtensile bond strength test and the fracture mode analysis. Results When the adhesive was applied three times before light curing, the bond strength of the ex- perimental subgroup 1 was significantly higher than that of the control subgroup 1 （47.46__＋13.91 vs. 38.12＋11.21 MPa, P〈O.05）. When using the technique of applying multiple layers of adhesive with each successive layer of light curing, no difference was observed in bond strength between the control subgroup and the experimental subgroup （39.40＋8.87 vs. 40.87-＋9.33 MPa, P〉O.05）. Conclusion Multiple coatings can improve the bond durability of one-step self-etching adhesive to primary dentin when using the technique of light-curing after applying 3 layers of adhesive.

The Study of the Grit-blasting Parameters and Their Effects on the Adhesive Strength of the Plasma Sprayed Coatings

Surface Preparation is very important in adhesive b on ding of spray coatings to the surface of a work piece. The common practice is gr it-blasting of the surface before subjecting it to the spray coating process. In this study, grit-blasting of an AISI 4130 steel (of different heat treatmen ts) with Al 2O 3 particles was studied. Various grit-blasting parameters such as blasting particle size, the distance between blasting nozzle and the work pi ece (25, 30 and 40 cm.), blasting pressure (3,4,5,6 and 7 bars), blasting time ( 3, 6 and 10 seconds), and the blasting angle (45° and 90°) were examined in or der to find the optimum roughness. The mean roughness (Ra) of the grit-blasted surfaces were measured and the vari ations of the roughness with respect to the above mentioned variables were studi ed. The results show that by increasing blasting time, surface roughness increas es up to a maximum and then slightly decreases it with further duration of t he process. On the other hand a lengthy blasting causes some undesirable results such as an increase in residual particles between surface irregularities. There fore an optimum blasting time is of great importance. Increasing the blasting pr essure also provides a rougher surface, but in grit blasting of harder specimens the surface roughness decreases when the pressure reaches a certain limit. About the blasting angle, it was noticed that an angle of 45° results in less r esidual particles between the surface irregularities, in comparison to the angle of 90°. After grit-blasting, the specimens were plasma spray coated with 80% ZrO 2-20 % Y 2O 3 powder. The adhesive strength of the coating to the substrate was the n measured according to the DIN 50160 standard. The results show that for a certain base metal, the adhesive strength is directl y related to the surface roughness of the base material. Residual particles afte r grit-blasting the surface of the specimens can also have a strong deteriorati ng effect on adhesive strength. Finally, it was shown that the hardness of the b ase material had a direct effect on the adhesive strength of the sprayed coating s.

High corrosion and wear resistant electroless Ni–P gradient coatings on aviation aluminum alloy parts

A Ni–P alloy gradient coating consisting of multiple electroless Ni–P layers with various phosphorus contents was prepared on the aviation aluminum alloy. Several characterization and electrochemical techniques were used to characterize the different Ni–P coatings’ morphologies, phase structures, elemental compositions, and corrosion protection. The gradient coating showed good adhesion and high corrosion and wear resistance, enabling the application of aluminum alloy in harsh environments. The results showed that the double zinc immersion was vital in obtaining excellent adhesion (81.2 N). The optimal coating was not peeled and shredded even after bending tests with angles higher than 90°and was not corroded visually after 500 h of neutral salt spray test at 35℃. The high corrosion resistance was attributed to the misaligning of these micro defects in the three different nickel alloy layers and the amorphous structure of the high P content in the outer layer. These findings guide the exploration of functional gradient coatings that meet the high application requirement of aluminum alloy parts in complicated and harsh aviation environments.

Improvement of anticorrosion and adhesion to magnesium alloy by phosphate coating formed at room temperature

A new surface protection process was developed to magnesium alloy against corrosion in aggressive environments.Firstly,a phosphate coating was formed on rinsed magnesium alloy.Then,powder painting was carried out on the phosphated magnesium alloy.Surface morphologies and phase compositions of the phosphate coating were investigated by X-ray diffraction(XRD) and scanning electron microscope(SEM) .The results show that the phosphate coatings formed in bath containing earth additives at room temperature have dense and fine microstructure.The phosphate coating provides excellent paint adhesion to the magnesium alloy. Salt spray tests indicate that the corrosion resistance of the phosphate coating plus paint could meet the demand of magnesium alloy automobile components in aggressive environments.

Sustainable, thermoplastic and hydrophobic coating from natural cellulose and cinnamon to fabricate eco-friendly catering packaging

Non-degradable polymers cause serious environmental pollution problem,such as the widely-used while unrecyclable coatings which significantly affect the overall degradation performance of products.It is imperative and attractive to develop biodegradable functional coatings.Herein,we proposed a novel strategy to successfully prepare biodegradable,thermoplastic and hydrophobic coatings with high transparence and biosafety by weakening the interchain interactions between cellulose chain.The natural cellulose and cinnamic acid were as raw materials.Via reducing the degree of polymerization(DP)of cellulose and regulating the degree of substitution(DS)of cinnamate moiety,the obtained cellulose cinnamate(CC)exhibited not only the thermalflow behavior but also good biodegradability,which solves the conflict between the thermoplasticity and biodegradability in cellulose-based materials.The glass transition temperature(T_(g))and thermalflow temperature(T_(f))of the CC could be adjusted in a range of 150–200℃ and 180–210℃,respectively.The CC with DS<1.2 and DP≤100 degraded more than 60%after an enzyme treatment for 7 days,and degraded more than 80%after a composting treatment for 42 days.Furthermore,CC had no toxicity to human epidermal cells even at a high concentration(0.5 mg mL^(-1)).In addition,CC could be easily fabricated into multifunctional coating with high hydrophobicity,thermal adhesion and high transparence.Therefore,after combining with cellophane and paperboard,CC coating with low DP and DS could be used to prepare fully-biodegradable heat-sealing packaging,art paper,paper cups,paper straws and food packaging boxes.

Microstructure, Adhesion and Wear of Plasma Sprayed AlSi-SiC Composite Coatings

Al-12.5 wt% Si alloy powder with 15 wt% SiCp was mechanically alloyed (MA) using attrition mill in purified nitrogen atmosphere. The MA processed powder was found to have nano grain size and uniform distribution of SiCp in the AlSi matrix. This MA processed powder was used for atmospheric plasma spraying (APS) for varying distances and currents densities. The coatings obtained were studied by image analyzer, SEM and XRD. Microhardness and wear rate of the coatings were evaluated using Vickers indenter and pin on disk type tribometer, respectively. Adhesion strength of the coatings was measured by interfacial indentation test. The results showed that these coatings have uniform distribution of reinforced SiC particles in the nano crystalline matrix, low porosity (1% - 2%), low wear rates and improved adhe-sion strength. It was also observed that by increasing current density of APS, the adhesive strength increased.

Evaluation for Adhesion Strength of Coating and Substrateby Burying Beforehand Specimen

Adhesion strength is an important target in evaluating the quality of coating layers.The traditional way of adhesion strength test is bonding pull off method for thick layers and scratch test for thin films.The drawbacks of these two methods are discussed in this paper,and an evaluating method for adhesion strength of coating by burying beforehand specimen is proposed.The adhesion strength of samples is measured with two methods.The dispersity of testing data is lower than that in the ASTM C663 79 Standard.

IMPROVEMENT OF ADHESION BETWEEN ION PLATED TiN COATING AND BASE METAL BY ADDING Y

The adhesion between the ion plated TiN coating and the base metal is improved by adding Y.The machenism of the effect of Y has been discussed as well.

Effect of manganese on the formation of hybrid zirconiumbased conversion coating on low carbon steel surface

This study revealed the effect of Mn on the formation of hybrid zirconium-based conversion coatings(HZCC)on low carbon steel.The XPS results indicated that the Mn compounds on the surface of low carbon steel were mainly MnO and Mn_(2)SiO_(4).Combined with the electrochemical measurements,the corrosion resistance of HZCC showed an increase followed by a decrease with increasing Mn concentration,which was related to the Mn_(2)SiO_(4) and SiO_(2) on the surface of low carbon steel.The excessive Mn concentration resulted in the loss of SiO_(2) and aggregation of Mn_(2)SiO_(4) on the low carbon steel surface,which caused the aggregation of Zr compounds on the surface and reduced the uniformity of the coating.Meanwhile,a moderate amount of Mn addition would be beneficial to increase the adhesion of organic coatings.

Effects of zincate treatment on adhesion of electroless Ni-P coating onto various aluminum alloys

The effects of alloying elements on zincate treatment and adhesion of electroless Ni-P coating onto various aluminum alloy substrates were examined.Surface morphology of zinc deposits in the 1st zincate treatment and its adhesion were changed depending on the alloying element.The zinc deposits in the 2nd zincate treatment became thinly uniform,and the adhesion between aluminum alloy substrate and Ni-P coating was improved irrespective of the alloying element.XPS analysis revealed the existence of zinc on the surface of each aluminum alloy substrate after the pickling in 5% nitric acid.This zinc on the surface should be an important factor influencing the morphology of zinc deposit at the 2nd zincate treatment and its adhesion.

A method for predicting critical load evaluating adhesion of coatings in scratch testing

In this paper based on the experiment principle of evaluating adhesion property by scratch testing, the peeling mechanism of thin films is discussed by applying contact theory and surface physics theory. A mathematical model predicting the critical load is proposed for calculating critical load as determined byscratch testing. The factors for correctly evaluating adhesion of coatings according to the experimental data arediscussed.

ADHESION STRENGTH OF COATING SUBSTRATE AND SURFACE MORPHOLOGY OF PRETREATMENT

Premature failure of coated tool often results from a poor adhesion of coating-substrate and shortens the lifetime of the tool. The results of increasing the adhesion strength of thin film coatings on cutting tool inserts by pretreating the inserts with sandblasting technique to obtain a desirable surface morphology of the inserts are presented. A geometric model representing the ideal surface morphology is established to enhance the nucleation density and adhesion strength of coating-substrate. Thin film coating experiment is conducted on the substrates of four different sample groups. Indentation and wear tests are performed on coated inserts to evaluate the effect of sandblasting on the adhesion strength of the coatings. A theoretical analysis is provided on the formation and growth of atom clusters in terms of the contact angle and the thermodynamic barrier of a substrate to predict thin film nucleation.

Evaluation of the Interfacial Adhesion between Brittle Coating and Ductile Substrate by Cross-Sectional Indention

The cross-sectional indentation method is extended to evaluate the interfacial adhesion between brittle coating and ductile substrate. The experimental results on electroplated chromium coating/steel substrate show that the interfacial separation occurs due to the edge chipping of brittle coating. The corresponding models are established to elucidate interfacial separation processes. This work further highlights the advantages and potential of this novel indentation method.

Employing SiO_2 Buffer Layer to Improve Adhesion of the Frequency-doubled Antireflection Coating on LBO

Frequency-doubled antireflection coatings simultaneously effective at 1064 nm and 532 nm were deposited on the lithium triborate （LiB3O5 or LBO） crystals using the electron beam evaporation method. Comparing with the sample without buffer layer, it is found that the adhesion of the sample with buffer layer of SiO2 between coating and LBO substrate is improved significantly from 137.4 mN to greater than 200 mN. And the laser-induced damage threshold is increased by 20% from 15.1 J/cm^2 to 18.6 J/cm^2. The strengthening mechanism of adhesion of the buffer layer of SiO2 is discussed by considering full plastic indentation and shear theory.

Improvement of human embryonic stem cell-derived retinal pigment epithelium cell adhesion, maturation, and function through coating with truncated recombinant human vitronectin

AIM:To explore an xeno-free and defined coating substrate suitable for the culture of H9 human embryonic stem cell-derived retinal pigment epithelial(hES-RPE)cells in vitro,and compare the behaviors and functions of h ESRPE cells on two culture substrates,laminin521(LN-521)and truncated recombinant human vitronectin(VTN-N).METHODS:hES-RPE cells were used in the experiment.The abilities of LN-521 and VTN-N at different concentrations to adhere to hES-RPE cells were compared with a high-content imaging system.Quantitative real-time polymerase chain reaction was used to evaluate RPE-specific gene expression levels midway(day 10)and at the end(day 20)of the time course.Cell polarity was observed by immunofluorescent staining for apical and basal markers of the RPE.The phagocytic ability of hES-RPE cells was identified by flow cytometry and immunofluorescence.RESULTS:The cell adhesion assay showed that the ability of LN-521 to adhere to hES-RPE cells was dosedependent.With increasing coating concentration,an increasing number of cells attached to the surface of LN-521-coated wells.In contrast,VTN-N presented a strong adhesive ability even at a low concentration.The optimal concentration of LN-521 and VTN-N required to coat and adhesion to hES-RPE cells were 2 and 0.25μg/cm^(2),respectively.Furthermore,both LN-521 and VTN-N could facilitate adoption of the desired cobblestone cellular morphology with tight junction and showed polarity by the hES-RPE cells.However,hES-RPE cells cultivated in VTN-N had a greater phagocytic ability,and it took less time for these hES-RPE cells to mature.CONCLUSION:VTN-N is a more suitable coating substrate for cultivating hES-RPE cells.

Correlation between Coating Adhesion and Damage Threshold: Simple Method of Reliability Assessment for Optoelectronic Applications

It is demonstrated that inherent coating adhesion and damage threshold are correlated for Ta2O5 and HfO2 coatings widely used in optoelectronic devices. By utilizing a newly proposed 1-h boiling water test combined with the optical aging under high-power laser irradiation, we show that an optical coating that survives the 1-h boiling water test withstands the damage threshold, ensuring the field service life even in harsh environments. Besides the standard evaluation methods, which may have limitations for applications required in harsh environments, the 1-h boiling water test can serve as an alternative method of reliability assessment for optical coatings. A heuristics herein can be used as a gating item for qualification of optical coatings for various applications.