Spectra of spontaneous Raman scattering in taper-drawn micro/nano-fibers

We study the spontaneous Raman scattering （RS） in taper-drawn micro/nano-fibers （MNFs） by employing the photon counting technique. The spectra of RS in five MNFs, which are fabricated by using different heating flames （hydrogen flame or butane flame） and with different diameters, are measured within a frequency shift range of 1435 cm- 1_3200 cm- 1. From the measured spectra, we observe the RS peaks originated from silica and a unique RS peak with a frequency shift of - 2905 cm-1 （- 87.2 THz）. Unlike the former ones, the latter one is not observable in conventional optical fibers. Furthermore, the unique peak becomes obvious and starts to rapidly increase with the decrease of the diameter of MNFs when the diameter is smaller than 2 μm, and the intensity of the unique peak significantly depends on the heating flame used in the fabricating process. Our investigation is useful for the entanglement generation or optical sensing using taper-drawn MNFs.

Research on the Development of Fibroin and Nano-Fiber from Silk Cocoons for Regenerated Tissue Engineering Applications by Electro-Spinning

In this paper, the main goal is to prepare silk fibroin nano-fiber, which is used for regenerated tissue applications. Silk scaffold nano-fibers made by electro-spinning technology can be used in regenerated tissue applications. The purpose of the research is to prepare a silk-fibroin nano-fiber solution for potential applications in tissue engineering. Using a degumming process, pure silk fibroin protein is extracted from silk cocoons. The protein solution for fibroin is purified, and the protein content is determined. The precise chemical composition, exact temperature, time, voltage, distance, ratio, and humidity all have a huge impact on degumming, solubility, and electro-spinning nano-fibers. The SEM investigates the morphology of silk fibroin nano-fibres at different magnifications. It also reveals the surface condition, fiber orientation, and fiber thickness of the silk fibroin nano-fiber. The results show that regenerated silk fibroin and nano-fiber can be used in silk fibroin scaffolds for various tissue engineering applications.

An energetic nano-fiber composite based on polystyrene and 1,3,5-trinitro-1,3,5-triazinane fabricated via electrospinning technique

Electrospinning is a simple technique used to fabricate polymeric nano-fibrous membranes.These nano-fibers have found a wide range of valuable applications in the biomedical field.However,it has not been utilized with solid high explosives yet.Herein,the electrospinning technique has been used to fabricate polystyrene(PS)/1,3,5-trinitro-1,3,5-triazinane(RDX)composite nanofibers.The governed electrospinning parameters,voltage,distance from the collector,flow rate,mandrel rotating speed,time,and solution concentration,that greatly affect the morphology of the obtained nanofibers were optimized.The fabricated PS/RDX nano-fibers were characterized using scanning electron microscopy(SEM),X-ray diffractometer(XRD),and Fourier Transform Infrared(FTIR)spectroscopy.The impact and friction sensitivities of PS/RDX were also measured.The thermal behavior of the prepared composite and the pure materials were studied by the thermal gravimetric analysis technique(TGA).SEM results proved the fabrication of PS/RDX fibers in the nano-size via electrospinning.FTIR spectroscopy confirmed the existence of the characteristic functional groups of both PS and RDX in the composite nano-fibers.XRD sharp peaks showed the conversion of amorphous PS into crystalline shape via electrospinning and also confirmed the formation of PS/RDX composite.The PS fibers absorbed the heat and increased the onset decomposition of the pure RDX from 181.5 to 200.7℃in the case of PS/RDX fibers.Interestingly,PS/RDX nano-fibers showed the relatively low impact and friction sensitivities of 100 J and 360 N respectively.These results could introduce PS/RDX nanofibrous composite in the field of explosives detection with high levels of safety.

Preparation of chain copper oxide nanoparticles by microwave

Cu（OH）2 nano-fibers were prepared by chemical precipitation with CuSO4·5H2O and NaOH as raw materials. The Cu（OH）2 nano-fibers have a diameter of 10-30 nm and a length of 1-6 μm. The reaction conditions were as follows： the concentration of CuSO4 solution was 0.1 mol·L^-1,NaOH solution 4 mol·L^-1,the dropping rate of the NaOH solution 50 mL·min^-1,the reaction temperature 20℃the pH value of the reaction terminal 13,and the stirring rate 1200 r·min^-1. The chain nano-CuO grains were obtained through the microwave radiation of the Cu（OH）2 nano-fibers.

Electrospinning and Electrospun Nanofibers

Electro-spinning is a very modern process which can be used in various purposes. We did this experimental work at Swerea IVF in Sweden during M. Sc in Textile Technology programme at University of Bor?s. We should especially thank our supervisor—Anna Thorvaldsson and course teacher—Ioannis S. Chronakis. In this report, we have tried to explain the basic manufacturing techniques of the electrospun nanofiber by the electro-spinning, how one can characterize it by SEM (Scanning Electron Microscopy) and its various applications in the practical field, e.g wound healing, Tissue Engineering Scaffold. The experimental work helped us a lot to gather sufficient knowledge about the electro-spinning process which we wanted to share with all.

Stability and activity of carbon nanofiber-supported catalysts in the aqueous phase reforming of ethylene glycol

Nickel, cobalt, copper and platinum nanoparticles supported on carbon nano-fibers were evaluated with respect to their stability, catalytic activity and selectivity in the aqueous phase reforming of ethylene glycol （230 ℃, autogenous pressure, batch reactor）. The initial surface-specific activities for ethylene glycol reforming were in a similar range but decreased in the order of Pt （15.5 h-1 ） 〉Co（13.0 h 1 ） 〉Ni（5.2 h-1） while the Cu catalyst only showed low dehydrogenation activity. The hydrogen molar selectivity decreased in the order of Pt （53%）〉Co（21%）〉Ni （15%） as a result of the production of methane over the latter two catalysts. Over the Co catalyst acids were formed in the liquid phase while alcohols were formed over Ni and Pt. Due to the low pH of the reaction mixture, especially in the case of Co （as a result of the formed acids）, significant cobalt leaching occurs which resulted in a rapid deactivation of this catalyst. Investigations of the spent catalysts with various techniques showed that metal particle growth is responsible for the deactivation of the Pt and Ni catalysts. In addition, coking might also contribute to the deactivation of the Ni catalyst.

Characterization and Influence of Nanofiber Flours of Wood Modified on Fresh State Properties of Cement Based Mortars

Nanofibrillated wood fiber was used as fillers in the partial cement matrix replacing the cement to a content of up to 2%by weight of cement.The nanofibrillated effect of wood fibers on porosity,thermal properties and compressive strength was studied.The results obtained showed an improvement in compressive strength of more than 40%with 1%by weight of wood fiber nanofibrillate.The addition of nanofibrillated wood fiber shows a good pore reduction,and the best result was obtained with emulsion of a mixture incorporating 1%by weight of wood fiber nanofibrillate in the presence of an anionic surfactant(SDBS).Thermal conductivity measurements and thermal expansion coefficient,compared to nanofibrillated wood fiber reinforced cement pastes,showed the reinforcing efficiency of cellulose fiber nanofibrillate.The degree of hydration of the cement increased with nanofibrillated wood fibers.This property has been confirmed by Fourier transform infrared spectroscopy.These analyzes revealed that the presence of nanofibrillated wood fibers generates and promotes the hydration of the cement,producing more portlandite and calcium silicate gel,which influences the compressive strength which gives a strong improvement.

Stabilization and Evaluation of Modified Nanofiber Flour Wood on the Properties of Cement-Baszd Mortar

The influence of nanofiberwood on the properties of the fresh condition of cement based mortars is not known in detail,despite recent advances in nanocellulose technology and it is related composite materials.Nanofiber wood from industrial waste,produced by high-pressure homogenization,was used as cement partial replacement for cement paste at a content ranging from 0%to 2%by weight of cement.The effect of the nanofiber wood content on the porosity,the compressive strength and the degree of hydration of the cement was investigated.Results have shown an improvement in the compressive strength by more than 50%with 1%of added fiber wood.The chemical modification of nanofibers wood by grafting of chains alkyls in their surfaces can reduce the quantity of water absorbed by the sample.The addition of an anionic additive(SDBS)in the water of mixing improves of more the surface of samples by minimizing the size of pores by emulsion effect,from where the absorption of water reduces.The degree of hydration of the cement has increased with the cellulose content containing nanofibrils.The analyze revealed that the presence of nanofiber wood favored the hydration of the cement by producing more calcium silicate gel and portlandite,probably the main reason for this improvement in compressive strength.

Influence and Dispersion of Nanofiber of Wood Modified on Properties of Cement Based Mortars

Wood nanofibers from industrial waste have been used as polymeric material to reinforce the cement paste to a content of up to 2%by weight of cement.The effect of the wood nanofibre content on the porosity,the compressive strength and the degree of hydration of the cement was studied.The results showed an improvement in compressive strength of over 50%with 1%of added fiberwood.Chemical modification of nanofiber wood by grafting alkyl chains to their surface can reduce the amount of water absorbed by the sample.Addition of an anionic additive(SDBS)to the mixing water improves the surface of the samples more and more by minimizing the pore size by emulsion effect,hence the water absorption decreases.The degree of hydration of the cement increased with the cellulose content containing nanofibrils.The analysis revealed that the presence of nanofibers favored the hydration of the cement by producing more calcium silicate gel and portlandite,probably the main reason for this improvement in compressive strength.

Stability of partially deacetylated chitin nano-fiber dispersions mediated by protonic acids

Partially deacetylated chitin nano-fiber(DAChN)dispersions were prepared using mechanical treatment of partially deacetylated crab shellα-chitin under acidic conditions mediated by various protonic acids.The representative organic acids had a better efficiency in terms of mediating the nanofibrillation of chitin fibers in comparison to the inorganic acid(HCl).The DAChN dispersed in water at a pH of 3.5 mediated by gluconic acid exhibited the highest yield of nano-fibers(88.6%),followed by succinic,itaconic,and ascorbic acids with a nano-fiber yield of 79.9%,73.3%and 66.0%,respectively.The pH,conductivity,viscosity,and light transmittance of dispersions were assessed under different storage times.All of the tested DAChN dispersions were stable for at least 15 weeks at 4℃.