Microstructure and Nano-hardness of Pure Copper and ODS Copper Alloy under Au Ions Irradiation at Room Temperature

The microstructure and nano-hardness of the pure copper and oxide dispersion-strengthened（ODS） copper alloy subjected to 1.4 Me V Au ions irradiation at room temperature were investigated. After irradiation, dislocation-loops form in both materials, while voids can only be generated in the pure copper. Compared with the irradiated pure copper, larger average diameter and lower number density of irradiation-induced dislocation-loops were detected in the ODS copper alloy, revealing that high-density dislocation and large volume of Al2O3 particles existing in the ODS copper alloy can act as effective sinks for the irradiation-induced defects. It was also detected that irradiation hardening in the ODS copper alloy is lower than that in the pure copper. The microstructure and nano-hardness results reveal that the ODS copper alloy has a better irradiation tolerance than the pure copper. In addition, the average diameter of the Al2O3 particles in the ODS copper alloy decreases after irradiation, because the Al–O chemical bonds are decomposed and the atoms are redistributed in the matrix during the irradiation process. This work reveals that the irradiation tolerance of the copper can be effectively enhanced by adding nano-sized Al2O3 particles into the matrix.

Microstructure, Hardness and Corrosion Resistance of ZrN Films Prepared by Inductively Coupled Plasma Enhanced RF Magnetron Sputtering

ZrN fihns were deposited on Si（111） and M2 steel by inductively coupled plasma （ICP）-enhanced RF magnetron sputtering. The effect of ICP power on the microstructure, mechanical properties and corrosion resistance of ZrN films was investigated. When the ICP power is below 300 W, the ZrN films show a columnar structure. With the increase of ICP power, the texture coefficient （To） of the （111） plane, the nanohardness and elastic modulus of the films increase and reach the maximum at a power of 300 W. As the ICP Power exceeds 300 W, the films exhibit a ZrN and ZrNx mixed crystal structure without columnar grain while the nanohardness and elastic modulus of the films decrease. All the ZrN coated samples show a higher corrosion resistance than that of the bare M2 steel substrate in 3.5% NaCl electrolyte. The nanohardness and elastic modulus mostly depend on the crystalline structure and Tc of ZrN（111）.

Wave Processes and Mass Transfer on the Copper-Stainless Steel Interface under Solid Phase Bonding by High-Temperature Rolling

The paper presents the study of hierarchy of deformation wave-processes from nano- to macro-structural level, which takes place in dissimilar materials, bonded by high-temperature vacuum rolling in solid phase. The focus was on the processes that occur on the interface of the bonded materials: mass trasfer of impurities and alloying elements stimulated by deformation, the study of nano- and micro-hardness.

Influence of La2O3 addition on nano indentation hardness and residual stress of Stellite 6 coating prepared by plasma cladding

One of the problems limiting the application of Stellite 6 coating is the residual stress resulting in cracks in the coating easily. In order to reduce the residual stress and increase the nano-indentation hardness,La2 O3 was added to Stellite 6 coating in this study, and the influence on the microstructure, nano indentation hardness and residual stress of the coatings were investigated by scanning electron microscopy（SEM） with energy dispersive spectrum（EDS）, X-ray diffraction（XRD） and nano-indentation tester. Results indicate that the addition of La2 O3 leads to the phenomenon that the dendrite is partly transformed into the equiaxed grain, which results in the grain refinement. The nano-indentation hardness of coatings is improved, which is attributed to the fine-grain strengthening and dispersion strengthening effect of La2 O3. With the addition of La2 O3, the residual stress in coatings is decreased significantly. Especially, when the content of La2 O3 is 0.8 wt%, the nano indentation hardness increases by 1.31 times and residual stress decreases to 20 percent, compared with coating without La2 O3.

Cold compression deformation method for reducing residual stress and uniformizing micro-property in ferrite steel

To reduce internal residual stress and homogenize micro-property of hot-rolled ferrite steel,the cold compression deformation method with small reduction rate has been performed in the hot-rolled samples,and X-ray diffraction and nanoindentation test have been used to detect the residual stress and micro-property.The samples with deformation rate of 0-5.59%or annealing at 550℃ are analyzed.The results show that,due to the coupling effect of thermal expansion and cold contraction and the volume expansion of microstructural transformation from austenite to ferrite,compressive residual stress was found inside the hot-rolled samples.With the increase in cold compression deformation,the dislocation density increased and the microhardness increased gradually,and there is no obvious rule for the change of mean nano-hardness in micro-zone for the center of samples.However,the uniformity of nano-hardness in the micro-zone increased first and then decreased,and the value of residual stress has obvious corresponding relationship with the uniformity of micro-zone property.The cold compression deformation with appropriate reduction rate can reduce residual stress and improve nano-hardness uniformity of the hot-rolled samples,but more deformation(such as reduction rateε=5.59%)makes residual stress increase and makes uniformity of nano-hardness deteriorate.

Morphology and distribution of precipitates and their effects on compression cracks in Fe-6.5Si-0.02B electrical steel

Morphology and distribution of precipitates in the Fe-6.5Si-0.02B alloy were characterized, and these effects on room- temperature compression cracks were investigated. The results showed that the precipitate in the Fe-6.5Si-0.02B alloy is FezB with body-centered tetragonal structure, and its nano-hardness is 15.0 GPa which is higher than that of the matrix （- 8.5 GPa）. In the as-cast alloys, most of the intragranular precipitates are coarse lath-like with the length of 5-15 μm and width of 2-5 μm, and the precipitates formed at the grain boundaries are of about 2-3 μm in width. After oil quenching followed by heat treatment at 1100 ℃ for more than 30 min, the precipitates inside grains are refined with a size of several hundred nanometers and the precipitates at the grain boundaries are refined with a size of 〈 1 μm. After compression test, transgranular and intergranular cracks occur in the as-cast alloys with coarse precipitates. For the quenched alloys with fine precipitates, the number of cracks decreases significantly, and no transgranular cracks happen because some cracks are blocked or the propagation direction is changed by grain boundary.