The total ribbon voltage of as-quenched and annealed Fe96-xZr_xB_4 (x=7 or 10) ribbons has been measured as a function of applied dc field and drive current frequency. The experimental results show that both samples e...The total ribbon voltage of as-quenched and annealed Fe96-xZr_xB_4 (x=7 or 10) ribbons has been measured as a function of applied dc field and drive current frequency. The experimental results show that both samples exist the optimum annealing temperature and optimum frequency at which the relative change in ribbon voltage is strongest, and the sensitivity of the magnetic response of the annealed Fe_89Zr_7B_4 ribbon is two order of magnitude larger than that of the annealed Fe_86Zr_10 B4 ribbon. The effect of magnetic properties and structural characteristics on giant magneto-impedance was discussed.展开更多
The giant magnetoimpedance effect of the nanocrystalline ribbonFe_(84)Zr_(2.08)Nb_(1.92)Cu_1B_(11) (atom fraction in %) was investigated. There is an optimumannealing temperature (T_A≈ 998 K) for obtaining the larges...The giant magnetoimpedance effect of the nanocrystalline ribbonFe_(84)Zr_(2.08)Nb_(1.92)Cu_1B_(11) (atom fraction in %) was investigated. There is an optimumannealing temperature (T_A≈ 998 K) for obtaining the largest GMI (giant magneto-impedance) effectin the ribbon Fe_(84)Zr_(2.08)Nb_(1.92)Cu_1B_(11). The ribbon with longer ribbon length has strongerGMI effect, which may be connected with the demagnetization effect of samples. The frequencyf_(max), where the maximum magnetoimpedance GMI(Z)_(max) = [(Z(H) - Z(0))/Z(0)]_(max) occurs, isnear the intersecting frequency f_i of the curves of GMI(R), GMI(X), and GMI(Z) versus frequency.The magnetoreactance GMI(X) decreases monotonically with increasing frequency, which may be due tothe decrease of permeability. In contrast, with the AC (alternating current) frequency increasing,the inagnetore-sistance GMI(R) increases at first, undergoes a peak, and under then drops. Theincrease of the magnetoresistance may result from the enhancement of the skin effect with frequency.The maximum magnetoimpedance value GMI(Z)_(max) under H = 7.2 kA/m is about -56.18% at f= 0.3 MHzfor the nanocrystalline ribbon Fe_(84)Zr_(2.08)Nb_(1.92)Cu_1B_(11) with the annealing temperatureT_A= 998 K and the ribbon length L = 6 cm.展开更多
The melt-spun nanocrystalline ribbons of Fe86.5Zr7B4Cu2.5 alloy were prepared by single wheel technique with wheel surface velocity of 37 m/s.It is found that there appears a lot ofα-Fe nanoparticles with sizes of 5-...The melt-spun nanocrystalline ribbons of Fe86.5Zr7B4Cu2.5 alloy were prepared by single wheel technique with wheel surface velocity of 37 m/s.It is found that there appears a lot ofα-Fe nanoparticles with sizes of 5-10 nm in as-spun nanocystalline ribbons which exhibit giant magnetoimpedance(GMI)effect.The GMI ratio up to 33.69% at frequency f=1MHz under a DC field of 5 172A/m can be obtained.展开更多
SINCE the discovery of the giant magneto-impedance (GMI) effects in amorphous wire (or rib-bon) of CoFeSiB and nanocrystalline wire (or film) of FeCuNbSiB, it has attracted greatattention due to its promising potentia...SINCE the discovery of the giant magneto-impedance (GMI) effects in amorphous wire (or rib-bon) of CoFeSiB and nanocrystalline wire (or film) of FeCuNbSiB, it has attracted greatattention due to its promising potential applications in industry. Amorphous (and nanocrys-talline) soft magnetic alloys have very large magnetic permeability, when an ac driving currentand an external magnetic field (EMF) are applied, the EMF will damp the magnetic fluxchange caused by the ac driving current, thus the magnetic permeability will decrease; as a re-展开更多
Three-dimensional flowerlike nanostructured metal oxides attached on the surfaces of Fe-based multi-phase nanocrys- talline ribbons （Fe-MNRs） were prepared by a simple way （through immersing the Fe-MNRs in Orange I...Three-dimensional flowerlike nanostructured metal oxides attached on the surfaces of Fe-based multi-phase nanocrys- talline ribbons （Fe-MNRs） were prepared by a simple way （through immersing the Fe-MNRs in Orange II solution）. It has been found that the as-prepared Fe-MNRs with 3D flowerlike nanostructures （Fe-MNRs ＋ FNs） exhibit good absorption property for a typical heavy metal ion （Cr^VI） in wastewater, while Fe-MNRs do not possess such properties. The Fe-MNRs ＋ FNs could remove 99% CrvI ions from the solution in 40 min, and this adsorption property can be attributed to the ion exchange between Cr^VI and surface hydroxyl groups （O-H） of 3D flowerlike nanostructures. The present result suggests that the Fe-MNRs ＋ FNs, prepared by facile way, possess great potentials in removing heavy metallic ions in wastewater.展开更多
The effects of ribbon thickness(t)on the structure and magnetic properties of a Fe_(82.3)B_(13)Cu_(1.7)Nb_(3) alloy in melt-spun and annealed states have been investigated.Increasing the t from 15 to 23μm changes the...The effects of ribbon thickness(t)on the structure and magnetic properties of a Fe_(82.3)B_(13)Cu_(1.7)Nb_(3) alloy in melt-spun and annealed states have been investigated.Increasing the t from 15 to 23μm changes the structure of the melt-spun ribbons from a single amorphous phase to a composite with denseα-Fe nanograins embedded in the amorphous matrix.The grain size(D_(α-Fe))of theα-Fe near the free surface of the ribbon is about 6.7 nm,and it gradually decreases along the cross section toward the wheel-contacted surface.Further increasing the t to 32μm coarsens the D_(α-Fe) near the free surface to 15.2 nm and aggravates the D_(α-Fe) ramp along the cross section.After annealing,the ribbon with t=15μm has relatively largeα-Fe grains with D_(α-Fe)>30 nm,while the thicker ribbons possessing the pre-existing nanograins form a finer nanostructure with D_(α-Fe)<16 nm.The structural uniformity of the ribbon with t=23μm is better than that of the ribbon with t=32μm.The annealed ribbons with t=23 and 32μm possess superior soft magnetic properties to the ribbon with t=15μm.The ribbon with t=23μm exhibits a high saturation magnetic flux density of 1.68 T,low coercivity of 9.6 A/m,and high effective permeability at 1 kHz of 15,000.The ribbon with t=32μm has a slightly larger coercivity due to the lower structural uniformity.The formation mechanism of the fine nanostructure for the ribbons with suitable t has been discussed in terms of the competitive growth effect among the pre-existingα-Fe nanograins.展开更多
利用单辊快淬法制备Fe Cu Nb Si B铁基纳米晶薄带。分析了热处理温度、热处理时间及冷却条件包括冷却速度与氧化程度对Fe Cu Nb Si B铁基纳米晶薄带高频磁导率的影响。随热处理温度的上升,铁基纳米晶铁芯的磁导率先增大而后出现不同程...利用单辊快淬法制备Fe Cu Nb Si B铁基纳米晶薄带。分析了热处理温度、热处理时间及冷却条件包括冷却速度与氧化程度对Fe Cu Nb Si B铁基纳米晶薄带高频磁导率的影响。随热处理温度的上升,铁基纳米晶铁芯的磁导率先增大而后出现不同程度的降低;在一定热处理温度,随热处理时间的延长,铁基纳米晶铁芯的磁导率逐渐减小;较快的冷却速度与氧化会降低铁基纳米晶铁芯的高频磁性能。展开更多
文摘The total ribbon voltage of as-quenched and annealed Fe96-xZr_xB_4 (x=7 or 10) ribbons has been measured as a function of applied dc field and drive current frequency. The experimental results show that both samples exist the optimum annealing temperature and optimum frequency at which the relative change in ribbon voltage is strongest, and the sensitivity of the magnetic response of the annealed Fe_89Zr_7B_4 ribbon is two order of magnitude larger than that of the annealed Fe_86Zr_10 B4 ribbon. The effect of magnetic properties and structural characteristics on giant magneto-impedance was discussed.
基金This work was financially supported by the National Natural Science Foundation of China (No. 50271036)
文摘The giant magnetoimpedance effect of the nanocrystalline ribbonFe_(84)Zr_(2.08)Nb_(1.92)Cu_1B_(11) (atom fraction in %) was investigated. There is an optimumannealing temperature (T_A≈ 998 K) for obtaining the largest GMI (giant magneto-impedance) effectin the ribbon Fe_(84)Zr_(2.08)Nb_(1.92)Cu_1B_(11). The ribbon with longer ribbon length has strongerGMI effect, which may be connected with the demagnetization effect of samples. The frequencyf_(max), where the maximum magnetoimpedance GMI(Z)_(max) = [(Z(H) - Z(0))/Z(0)]_(max) occurs, isnear the intersecting frequency f_i of the curves of GMI(R), GMI(X), and GMI(Z) versus frequency.The magnetoreactance GMI(X) decreases monotonically with increasing frequency, which may be due tothe decrease of permeability. In contrast, with the AC (alternating current) frequency increasing,the inagnetore-sistance GMI(R) increases at first, undergoes a peak, and under then drops. Theincrease of the magnetoresistance may result from the enhancement of the skin effect with frequency.The maximum magnetoimpedance value GMI(Z)_(max) under H = 7.2 kA/m is about -56.18% at f= 0.3 MHzfor the nanocrystalline ribbon Fe_(84)Zr_(2.08)Nb_(1.92)Cu_1B_(11) with the annealing temperatureT_A= 998 K and the ribbon length L = 6 cm.
文摘The melt-spun nanocrystalline ribbons of Fe86.5Zr7B4Cu2.5 alloy were prepared by single wheel technique with wheel surface velocity of 37 m/s.It is found that there appears a lot ofα-Fe nanoparticles with sizes of 5-10 nm in as-spun nanocystalline ribbons which exhibit giant magnetoimpedance(GMI)effect.The GMI ratio up to 33.69% at frequency f=1MHz under a DC field of 5 172A/m can be obtained.
文摘SINCE the discovery of the giant magneto-impedance (GMI) effects in amorphous wire (or rib-bon) of CoFeSiB and nanocrystalline wire (or film) of FeCuNbSiB, it has attracted greatattention due to its promising potential applications in industry. Amorphous (and nanocrys-talline) soft magnetic alloys have very large magnetic permeability, when an ac driving currentand an external magnetic field (EMF) are applied, the EMF will damp the magnetic fluxchange caused by the ac driving current, thus the magnetic permeability will decrease; as a re-
基金This work was supported by the National Key Basic Research and Development Programme （Grant No.2016YFB0300500） and the National Natural Science Foundation of China （NSFC, Grant Nos. 51571127 and 51771096）.
文摘Three-dimensional flowerlike nanostructured metal oxides attached on the surfaces of Fe-based multi-phase nanocrys- talline ribbons （Fe-MNRs） were prepared by a simple way （through immersing the Fe-MNRs in Orange II solution）. It has been found that the as-prepared Fe-MNRs with 3D flowerlike nanostructures （Fe-MNRs ＋ FNs） exhibit good absorption property for a typical heavy metal ion （Cr^VI） in wastewater, while Fe-MNRs do not possess such properties. The Fe-MNRs ＋ FNs could remove 99% CrvI ions from the solution in 40 min, and this adsorption property can be attributed to the ion exchange between Cr^VI and surface hydroxyl groups （O-H） of 3D flowerlike nanostructures. The present result suggests that the Fe-MNRs ＋ FNs, prepared by facile way, possess great potentials in removing heavy metallic ions in wastewater.
基金supported by the National Natural Science Foundation of China(Grant Nos.51871039,51771039 and 51571047)。
文摘The effects of ribbon thickness(t)on the structure and magnetic properties of a Fe_(82.3)B_(13)Cu_(1.7)Nb_(3) alloy in melt-spun and annealed states have been investigated.Increasing the t from 15 to 23μm changes the structure of the melt-spun ribbons from a single amorphous phase to a composite with denseα-Fe nanograins embedded in the amorphous matrix.The grain size(D_(α-Fe))of theα-Fe near the free surface of the ribbon is about 6.7 nm,and it gradually decreases along the cross section toward the wheel-contacted surface.Further increasing the t to 32μm coarsens the D_(α-Fe) near the free surface to 15.2 nm and aggravates the D_(α-Fe) ramp along the cross section.After annealing,the ribbon with t=15μm has relatively largeα-Fe grains with D_(α-Fe)>30 nm,while the thicker ribbons possessing the pre-existing nanograins form a finer nanostructure with D_(α-Fe)<16 nm.The structural uniformity of the ribbon with t=23μm is better than that of the ribbon with t=32μm.The annealed ribbons with t=23 and 32μm possess superior soft magnetic properties to the ribbon with t=15μm.The ribbon with t=23μm exhibits a high saturation magnetic flux density of 1.68 T,low coercivity of 9.6 A/m,and high effective permeability at 1 kHz of 15,000.The ribbon with t=32μm has a slightly larger coercivity due to the lower structural uniformity.The formation mechanism of the fine nanostructure for the ribbons with suitable t has been discussed in terms of the competitive growth effect among the pre-existingα-Fe nanograins.
文摘利用单辊快淬法制备Fe Cu Nb Si B铁基纳米晶薄带。分析了热处理温度、热处理时间及冷却条件包括冷却速度与氧化程度对Fe Cu Nb Si B铁基纳米晶薄带高频磁导率的影响。随热处理温度的上升,铁基纳米晶铁芯的磁导率先增大而后出现不同程度的降低;在一定热处理温度,随热处理时间的延长,铁基纳米晶铁芯的磁导率逐渐减小;较快的冷却速度与氧化会降低铁基纳米晶铁芯的高频磁性能。
