Quasi-plane-hypothesis of strain coordination for RC beams seismically strengthened with externally-bonded or near-surface mounted fiber reinforced plastic

The application of fiber reinforced plastic（FRP）,including carbon FRP and glass FRP,for structural repair and strengthening has grown due to their numerous advantages over conventional materials such as externally bonded reinforcement（EBR） and near-surface mounted（NSM） strengthening techniques.This paper summarizes the results from 21 reinforced concrete beams strengthened with different methods,including externally-bonded and near-surface mounted FRP,to study the strain coordination of the FRP and steel rebar of the RC beam.Since there is relative slipping between the RC beam and the FRP,the strain of the FRP and steel rebar of the RC beam satisfy the quasi-plane-hypothesis;that is,the strain of the longitudinal fiber that parallels the neutral axis of the plated beam within the scope of the effective height（h 0） of the cross section is in direct proportion to the distance from the fiber to the neutral axis.The strain of the FRP and steel rebar satisfies the equation：ε FRP =βε steel,and the value of β is equal to 1.1-1.3 according to the test results.

First assessment of Noise-Equivalent Sigma-Zero in GF3-02 TOPSAR mode with sea surface wind speed retrieval

Gaofen-3-02(GF3-02)is the first C-band synthetic aperture radar(SAR)satellite with terrain observation with progressive scans of SAR(TOPSAR)imaging mode in China,which plays an essential role in marine environment monitoring.Given the weak scattering characteristics of the ocean,the system thermal noise superimposed on SAR images has significant interference,especially in cross-polarization channels.Noise-Equivalent Sigma-Zero(NESZ)is a measure of the sensitivity of the radar to areas of low backscatter.The NESZ is defined to be the scattering cross-section coefficient of an area which contributes a mean level in the image equal to the signal-independent additive noise level.For TOPSAR,NESZ exhibits the shape of the SAR scanning gain curve in the azimuth and the shape of the antenna pattern in the range.Therefore,the accurate measurement of NESZ plays a vital role in the application of spaceborne SAR sea surface cross-polarization data.This paper proposes a theoretical calculation method for the NESZ curve in GF3-02 TOPSAR mode based on SAR noise inner calibration data and the imaging algorithm.A method for correcting the error existing in the theoretical curve of NESZ is also proposed according to the relationship between sea surface backscattering and wind speed and the same characteristics of target scattering in the overlapping area of adjacent sub-swaths.According to assessment with wide-swath TOPSAR cross-polarization data,the GF3-02 TOPSAR mode has a very low thermal noise level,which is better than−33 dB at the edge of each beam,and controlled below−38 dB at the center of the beam.The two-dimensional reference curves of the NESZ of each beam are provided to the GF3-02 TOPSAR users.After discussing the relationship between normalized radar cross section(NRCS)and wind speed,we provide a formula for NRCS related to wind speed and radar incidence angle.Compared with the NRCS derived from this formula and the NESZ-subtracted NRCS of SAR images,the bias is−0.0048 dB,the Root Mean Square Error is 1.671 dB and the correlation coefficient is 0.939.

Analytical calculation of electromagnetic, torque for surface mounted permanent magnet brushless motors

With the air gap magnetic field distribution of surface mounted permanent magnet （PM） motors obtained using an analytical technique, the instantaneous electromagnetic torque and its corresponding components are investigated with the Maxwell stress tensor method. Accurate results can easily be achieved using the proposed method without using the tedious finite element analysis （FEA）. In this paper, the electromagnetic torque of a surface mounted PM motor with two phases energized is decomposed into four torque components. This technique is useful not only for the design and optimization of the permanent magnet motor, but also for the choice of control strategy.

Finite element simulation for mechanical response of surface mounted solder joints under different temperature cycling

Nonlinear finite element simulation for mechanical response of surface mounted solder joint under different temperature cycling was carried out. Seven sets of parameters were used in order to evaluate the influence of temperature cycling profile parameters. The results show that temperature cycling history has significant effect on the stress response of the solder joint. Based on the concept of relative damage stress proposed by the authors, it is found that enough high temperature holding time is necessary for designing the temperature cycling profile in accelerated thermal fatigue test.

Hierarchical planning for a surface mounting machine placement

For a surface mounting machine (SMM) in printed circuit board (PCB) assembly line, there are four problems, e.g. CAD data conversion, nozzle selection, feeder assignment and placement sequence determination. A hierarchical planning for them to maximize the throughput rate of an SMM is presented here. To minimize set-up time, a CAD data conversion system was first applied that could automatically generate the data for machine placement from CAD design data files. Then an effective nozzle selection approach was implemented to minimize the time of nozzle changing. And then, to minimize picking time, an algorithm for feeder assignment was used to make picking multiple components simultaneously as much as possible. Finally, in order to shorten pick-and-place time, a heuristic algorithm was used to determine optimal component placement sequence according to the decided feeder positions. Experiments were conducted on a four head SMM. The experimental results were used to analyse the assembly line performance.

Add-on pegylated interferon augments hepatitis B surface antigen clearance vs continuous nucleos(t)ide analog monotherapy in Chinese patients with chronic hepatitis B and hepatitis B surface antigen≤1500 IU/mL:An observational study

BACKGROUND Nucleos(t)ide analog(NA)has shown limited effectiveness against hepatitis B surface antigen(HBsAg)clearance in chronic hepatitis B(CHB)patients.AIM To evaluate the efficacy and safety of add-on peginterferonα-2a(peg-IFNα-2a)to an ongoing NA regimen in CHB patients.METHODS In this observational study,195 CHB patients with HBsAg≤1500 IU/m L,hepatitis B e antigen(HBeAg)-negative(including HBeAg-negative patients or HBeAg-positive patients who achieved HBeAg-negative after antiviral treatment with NA)and hepatitis B virus-deoxyribonucleic acid<1.0×10^2 IU/mL after over 1 year of NA therapy were enrolled between November 2015 and December2018 at the Second Affiliated Hospital of Xi'an Jiaotong University,China.Patients were given the choice between receiving either peg-IFNα-2a add-on therapy to an ongoing NA regimen(add-on group,n=91)or continuous NA monotherapy(monotherapy group,n=104)after being informed of the benefits and risks of the peg-IFNα-2a therapy.Total therapy duration of peg-IFNα-2a was 48 wk.All patients were followed-up to week 72(24 wk after discontinuation of peg-IFNα-2a).The primary endpoint was the proportion of patients with HBsAg clearance at week 72.RESULTS Demographic and baseline characteristics were comparable between the two groups.Intention-to-treatment analysis showed that the HBsAg clearance rate in the add-on group and monotherapy group was 37.4%(34/91)and 1.9%(2/104)at week 72,respectively.The HBsAg seroconversion rate in the add-on group was 29.7%(27/91)at week 72,and no patient in the monotherapy group achieved HBsAg seroconversion at week 72.The HBsAg clearance and seroconversion rates in the add-on group were significantly higher than in the monotherapy group at week 72(P<0.001).Younger patients,lower baseline HBsAg concentration,lower HBsAg concentrations at weeks 12 and 24,greater HBsAg decline from baseline to weeks 12 and 24 and the alanine aminotransferase≥2×upper limit of normal during the first 12 wk of therapy were strong predictors of HBsAg clearance in patients with peg-IFNα-2a add-on treatment.Regarding the safety of the treatment,4.4%(4/91)of patients in the add-on group discontinued peg-IFNα-2a due to adverse events.No severe adverse events were noted.CONCLUSION Peg-IFNα-2a as an add-on therapy augments HBsAg clearance in HBeAg-negative CHB patients with HBsAg≤1500 IU/m L after over 1 year of NA therapy.

CALCULATION OF THREE－DIMENSIONAL SOLDER JOINT FORMATION IN MICROELECTRONIC SURFACE MOUNT TECHNOLOGY

A finite element analysis for calculating three-dimensional(3-D) solder joint shape between chip component and substrate pad was carried out, and the effects of solder volume and pad extension beyond the edge of component on solder joint shapes were investigated. The resonable design ranges of solder volume and pad extension have been put forward.

Surface and Texture Properties of Tb-Doped Ceria-Zirconia Solid Solution Prepared by Sol-Gel Method

The three-way catalysts （TWCs） promoters Ce0.6Zr0.4- x TbxO2-y were prepared by sol-gel method. BET surface areas analysis indicated that an increase of the dopant Tb content from x = 0.05 to x = 0.15 favors an increase of surface area from 66.8 to 80.4 m^2· g^-1 compared with the undoped sample Ce0 .6oZr0.40O2 65.1 m^2·g^- 1 after calcination at 650℃. Transmission electron microscopy （TEM） observation indicated that the doped samples have a higher thermal stability. The XRD and Raman spectra confirmed that the Ce0.6Zr0.4-xTbxO2-y cubic solid solution is formed. XPS analysis revealed that Ce and Tb mainly existed in the form of Ce^4＋ and Tb^3 ＋ , and Zr existed in the form of Zr^4＋ on the surface of the samples. The doped samples were homogenous in composition ; the introduction of Tb into the CeO2-ZrO2 promoters resuited in the formation of a solid solution, and the concentration of surface lattice oxygen was increased.

First-principles Study on Geometric and Electronic Structures of Si（111）-√7× √3-In Surface Reconstruction

In order to determine the structures of Si（111）-√7 √3-In surfaces and to understand their electronic properties, we construct six models of both hexagonal and rectangular types and perform first-principles calculations. Their scanning tunneling microscopic images and work functions are simulated and compared with experimental results. In this way, the hex-H3＇ and rect-T1 models are identified as the experimental configurations for the hexagonal and rectangular types, respectively. The structural evolution mechanism of the In/Si（lll） surface with indium coverage around 1.0 monolayer is discussed. The 4×1 and -√7× √3 phases are suggested to have two different types of evolution mechanisms, consistent with experimental results.

The 30–60-day Intraseasonal Variability of Sea Surface Temperature in the South China Sea during May–September

This study investigates the structure and propagation of intraseasonal sea surface temperature（SST） variability in the South China Sea（SCS） on the 30-60-day timescale during boreal summer（May-September）. TRMM-based SST, GODAS oceanic reanalysis and ERA-Interim atmospheric reanalysis datasets from 1998 to 2013 are used to examine quantitatively the atmospheric thermodynamic and oceanic dynamic mechanisms responsible for its formation. Power spectra show that the 30-60-day SST variability is predominant, accounting for 60% of the variance of the 10-90-day variability over most of the SCS. Composite analyses demonstrate that the 30-60-day SST variability is characterized by the alternate occurrence of basin-wide positive and negative SST anomalies in the SCS, with positive（negative） SST anomalies accompanied by anomalous northeasterlies（southwesterlies）. The transition and expansion of SST anomalies are driven by the monsoonal trough-ridge seesaw pattern that migrates northward from the equator to the northern SCS. Quantitative diagnosis of the composite mixed-layer heat budgets shows that, within a strong 30-60-day cycle, the atmospheric thermal forcing is indeed a dominant factor, with the mixed-layer net heat flux（MNHF） contributing around 60% of the total SST tendency, while vertical entrainment contributes more than 30%. However, the entrainment-induced SST tendency is sometimes as large as the MNHF-induced component, implying that ocean processes are sometimes as important as surface fluxes in generating the30-60-day SST variability in the SCS.

Effects of Zr/Ti molar ratio in SO_4^(2-)/ZrO_(2-)TiO_2 calcined at different temperatures on its surface properties and glucose reactivity in near-critical methanol

Effects of Zr/Ti molar ratio in SO42-/ZrO2-TiO2 solid acid catalyst calcined at different temperatures on its surface properties and catalytic activity were thoroughly investigated in this paper. The physicochemical characteristics of prepared samples were determined by N2 adsorptiondesorption, XRD, NH3-TPD and XPS techniques, respectively. It was found that the crystallization temperature of the samples increased after the combination of ZrO2 and TiO2; and phase transformations from the anatase to the rutile of TiO2 species and the tetragonal to the monoclinic of ZrO2 species were effectively suppressed at higher temperature. The sample with a Zr/Ti molar ratio of 3/1 calcined at 450℃ showed the highest surface area and the most acid sites among all the tested samples. The acid site densities of samples were relatively closed to each other if they were calcined at the same temperature, however, decreased with the calcination temperature. The result indicates that the sulfur content in samples is a crucial factor to control the acid site density. Calcining the sample at 650℃ and higher temperatures resulted in a significant desorption of sulfate ion on the samples. The synthesized samples were evaluated as a potential catalyst for glucose conversion under the near-critical methanol conditions （200℃/4 MPa）. The results suggested that the relatively weaker acid sites of the catalyst were more favorable for the accumulation of methyl glucosides, while the moderate acid sites were responsible for the formation of methyl levulinate. The catalytic activity for methyl levulinate production almost increases linearly with the catalyst acid site density. The catalyst deactivation is due to the loss of sulfate ion and the two catalysts with Zr/Ti molar ratios of 3/1 and 1/3 could effectively alleviate the deactivation caused by sulfate solution in the reaction medium and can be reused after calcination with the reuse rate of over 90% in terms of the methyl levulinate selectivity.

A novel type of transverse surface wave propagating in a layered structure consisting of a piezoelectric layer attached to an elastic half-space

The existence and propagation of transverse surface waves in piezoelectric coupled solids is investigated, in which perfect bonding between a metal/dielectric substrate and a piezoelectric layer of finite-thickness is assumed. Dis- persion equations relating phase velocity to material con- stants for the existence of various modes are obtained in a simple mathematical form for a piezoelectric material of class 6mm. It is discovered and proved by numerical examples in this paper that a novel Bleustein-Gulyaev （B-G） type of transverse surface wave can exist in such piezoelectric cou- pled solid media when the bulk-shear-wave velocity in the substrate is less than that in the piezoelectric layer but greater than the corresponding B-G wave velocity in the same pie- zoelectric material with an electroded surface. Such a wave does not exist in such layered structures in the absence of pie- zoelectricity. The mode shapes for displacement and electric potential in the piezoelectric layer are obtained and discussed theoretically. The study extends the regime of transverse sur- face waves and may lead to potential applications to surface acoustic wave devices.

High-Speed,High-Power Motor Design for a Four-Legged Robot Actuator Optimized using the Weighted Sum and Response Surface Methods

In this paper,a design is presented for a high-speed,high-power motor for a four-legged robot actuator that was optimized using the weighted sum method(WSM)based on the Taguchi method,and the response surface method(RSM).First,output torque,torque constant,torque ripple,and efficiency were selected as objective functions for the optimized design.The sampling method was implemented to use a mixed orthogonal array and the single response characteristics of each objective function were compared using the Taguchi method.Moreover,to consider the multi-response characteristic of the objective functions,WSM was applied.Second,the 2D finite element analysis result of the RSM was compared with that using the WSM.Finally,an experiment was carried out on the manufactured motor and the optimized model is presented here.

3D v_P and v_S models of southeastern margin of the Tibetan plateau from joint inversion of body-wave arrival times and surface-wave dispersion data

A new 3D velocity model of the crust and upper mantle in the southeastern （SE） margin of the Tibetan plateau was obtained by joint inversion of body- and sur- face-wave data. For the body-wave data, we used 7190 events recorded by 102 stations in the SE margin of the Tibetan plateau. The surface-wave data consist of Rayleigh wave phase velocity dispersion curves obtained from ambient noise cross-correlation analysis recorded by a dense array in the SE margin of the Tibetan plateau. The joint inversion clearly improves the Vs model because it is constrained by both data types. The results show that at around 10 km depth there are two low-velocity anomalies embedded within three high-velocity bodies along the Longmenshan fault system. These high-velocity bodies correspond well with the Precambrian massifs, and the two located to the northeast of 2013 Ms 7.0 Lushan earthquake are associated with high fault slip areas during the 2008 Wenchuan earthquake. The aftershock gap between 2013 Lushan earthquake and 2008 Wenchuan earthquake is associated with low-velocity anomalies, which also acts as a barrier zone for ruptures of two earthquakes. Generally large earthquakes （M 〉 5） in the region occurring from 2008 to 2015 are located around the high-velocity zones, indicating that they may act as asperities for these large earthquakes. Joint inversion results also clearly show that there exist low-velocity or weak zones in the mid-lower crust, which are not evenly distributed beneath the SE margin of Tibetan plateau.

Experimental Study on Momentum Transfer of Surface Texture in Taylor-Couette Flow

The behavior of Taylor-Couette （TC） flow has been extensively studied. However, no suitable torque prediction models exist for high-capacity fluid machinery. The Eckhardt-Grossmann-Lohse （EGL） theory, derived based on the Navier-Stokes equations, is proposed to model torque behavior. This are the significant energy theory suggests that surfaces transfer interfaces between cylinders and annular flow. This study mainly focuses on the effects of surface texture on momentum transfer behavior through global torque measurement. First, a power-law torque behavior model is built to reveal the relationship between dimensionless torque and the Taylor number based on the EGL theory. Second, TC flow appa- ratus is designed and built based on the CNC machine tool to verify the torque behavior model. Third, four surface texture films are tested to check the effects of surface texture on momentum transfer. A stereo microscope and three-dimensional topography instrument are employed to analyze surface morphology. Global torque behavior is measured by rotating a multi component dynamometer, and the effects of surface texture on the annular flow behavior are observed via images obtained using a high-speed camera. Finally, torque behaviors under four differentsurface conditions are fitted and compared. The experi- mental results indicate that surface textures have a remarkable influence on torque behavior, and that the peak roughness of surface texture enhances the momentum transfer by strengthening the fluctuation in the TC flow.

1,1'-联萘-2,2'-二胺的两种同质异晶的晶体结构及其Hirshfeld Surfaces分析

设计合成了1,1'-联萘-2,2'-二胺的两种同质异晶,利用X-单晶衍射对其单晶结构进行表征,并对其Hirshfeld surfaces进行了分析。结果表明,分子间的弱作用力在化合物的超分子自组装中起着关键作用。

Interaction of Photoactive[Fe(CN)_6]^(4-) with TiO_2 Anatase(101) Surface:A Periodic Density Functional Theory Study

The plane-wave pseudopotential function method, based on density-functional theory, has been used to calculate the adsorption, electronic band structures, orbitals and optical absorption spectrum of [Fe（CN）6]^4- on TiOz anatase（101） surface. Our calculations reveal that the surface-modified anatase system has large adsorption energy and a much narrower band gap. [Fe（CN）6]^4- adsorption on the （101） surface could lead to a large red shift of the anatase optical absorption threshold, which extends into a visible region significantly. The calculated results are in agreement with the experiment and other theoretical studies reasonably. It is very important for the understanding and further development ofphotovoltaic materials that are active under visible light.

白桦脂酸-乙醇(1:1)的晶体结构及Hirshfeld Surface分析

白桦脂酸是一种具有多种药理活性的五环三萜类天然产物,已报道的其单晶体均为白桦脂酸-有机溶剂形式。本研究通过溶剂挥发法制备了白桦脂酸-乙醇(1:1)单晶体,通过X射线衍射法获得了其单晶数据,用Hirshfeld surface分析法对晶体中分子间作用力进行了分析。晶体结构分析结果为揭示其理化性质与成因等提供了基础科学数据,为该晶型的定性、定量分析及制备工艺研究提了标准依据,为白桦脂酸多晶型的筛选及共晶的设计提供了数据参考。

XPS STUDIES ON SURFACE MODIFIED POLY [1-(TRIMETHYLSILYL)-1-PROPYNE] MEMBRANES Ⅱ SURFACE MODIFICATION BY BROMINE VAPOR

Surface modification of poly [1-(trimethylsilyl)-1-propyne] (PTMSP) membranes bybromine vapor has been studied. It is shown that Br/C atomic ratio at the surfaces increased withthe time of bromination until about 60 min, then it reached a plateau. The results of XPS and IRstudies indicated that the addition of bromine to double bonds and the replacement of H on CH_3 bybromine had taken place so that a new peak at 286.0 eV (C--Br)in C_(1s) spectra and some newbands, e. g. at 1220 and 580cm^(-1) in IR spectra were formed. The fact,t Po_2, permeability ofoxygen, decreased and α_(O_2/N_2), separation factor of oxygen relative to nitrogen, increased withbromination time, shows that surface modification of PTMSP by bromine may be an efficient approach to prepare PTMSP membranes used for practical gas separations.

Formation and local electronic structure of Ge clusters on Si（111）-7×7 surfaces

We report the formation and local electronic structure of Ge clusters on the Si（111）-7×7 surface studied by using variable temperature scanning tunnelling microscopy （VT-STM） and low-temperature scanning tunnelling spectroscopy （STS）. Atom-resolved STM images reveal that the Ce atoms are prone to forming clusters with 1.0 nm in diameter for coverage up to 0.12 ML. Such Ce clusters preferentially nucleate at the centre of the faulted-half unit cells, leading to the ＇dark sites＇ of Si centre adatoms from the surrounding three unfaulted-half unit cells in filled-state images. Biasdependent STM images show the charge transfer from the neighbouring Si adatoms to Ce clusters. Low-temperature STS of the Ce clusters reveals that there is a band gap on the Ce cluster and the large voltage threshold is about 0.9 V.