COMPLETE KAHLER METRICS WITH POSITIVE HOLOMORPHIC SECTIONAL CURVATURES ON CERTAIN LINE BUNDLES(RELATED TO A COHOMOGENEITY ONE POINT OF VIEW ON A YAU CONJECTURE)

In this article,we study Kahler metrics on a certain line bundle over some compact Kahler manifolds to find complete Kahler metrics with positive holomorphic sectional(or bisectional)curvatures.Thus,we apply a strategy to a famous Yau conjecture with a co-homogeneity one geometry.

THE LOGARITHMIC SOBOLEV INEQUALITY FOR A SUBMANIFOLD IN MANIFOLDS WITH ASYMPTOTICALLY NONNEGATIVE SECTIONAL CURVATURE

In this note,we prove a logarithmic Sobolev inequality which holds for compact submanifolds without a boundary in manifolds with asymptotically nonnegative sectional curvature.Like the Michale-Simon Sobolev inequality,this inequality contains a term involving the mean curvature.

Distribution and correlation of refractive parameters in children with different corneal curvatures in southeast China

AIM:To analyze the distribution of refractive status in school-age children with different corneal curvatures(CC)and the correlation between CC and refractive status.METHODS:A total of 2214 school-aged children of grade 4 in Hangzhou who were screened for school myopia were included.Uncorrected distance visual acuity(UCDVA),non-cycloplegic refraction,axial length(AL),horizontal and vertical corneal curvature(K1,K2)were measured and spherical equivalent(SE),corneal curvature radius(CCR)and axial length/corneal radius of curvature ratio(AL/CR)were calculated.UCDVA<5.0 and SE≤-0.50 D were classified as school-screening myopia.According to the different CCRs,the patients were divided into the lower corneal curvature(LCC)group(CCR≥7.92)and the higher corneal curvature(HCC)group(CCR<7.92).Each group was further divided into the normal AL subgroup and the long AL subgroup.The refractive parameters were compared to identify any differences between the two groups.RESULTS:Both SE and AL were greater in the LCC group(P=0.013,P<0.001).The prevalence of myopia was 38% in the LCC group and 44% in the HCC group(P<0.001).The proportion of children without screening myopia was higher in the LCC group(62%)than in the HCC group(56%).Among these children without screening myopia,the proportion of long AL in the LCC group(24%)was significantly higher than that in the HCC group(0.012%;P<0.001).The change of SE in the LCC group was less affected by the increase of AL than that in the HCC group.CONCLUSION:School-aged children in the LCC group have a lower incidence of screening myopia and longer AL.Low CC can mask SE reduction and AL growth to some extent,and the change of AL growth change more in children with low CC than high CC.Before the onset of myopia,its growth rate is even faster than that after the onset of myopia.

Gradient Estimate of Solutions to a Class of Mean Curvature Equations with Prescribed Contact Angle Boundary Problem

This paper studies the prescribed contact angle boundary value problem of a certain type of mean curvature equation.Applying the maximum principle and the moving frame method and based on the location of the maximum point,the boundary gradient estimation of the solutions to the equation is obtained.

RANDERS SPACES WITH SCALAR FLAG CURVATURE

Let(M, F) be an n-dimensional Randers space with scalar flag curvature. In this paper, we will introduce the definition of a weak Einstein manifold. We can prove that if(M, F) is a weak Einstein manifold, then the flag curvature is constant.

A CLASS OF INVERSE QUOTIENT CURVATURE FLOW IN THE ADS-SCHWARZSCHILD MANIFOLD

In this paper,we study the asymptotic behavior of a class of inverse quotient curvature flow in the anti-de Sitter-Schwarzschild manifold.We prove that under suitable convex conditions for the initial hypersurface,one can get the long-time existence for the inverse curvature flow.Moreover,we also get that the principal curvatures of the evolving hypersurface converge to 1 when t→+∞.

Microcurvature landscapes induce neural stem cell polarity and enhance neural differentiation

Tissue curvature has long been recognized as an important anatomical parameter that affects intracellular behaviors,and there is emerging interest in applying cell-scale curvature as a designer property to drive cell fates for tissue engineering purposes.Although neural cells are known to undergo dramatic and terminal morphological changes during development and curvature-limiting behaviors have been demonstrated in neurite outgrowth studies,there are still crucial gaps in understanding neural cell behaviors,particularly in the context of a three-dimensional(3D)curvature landscape similar to an actual tissue engineering scaffold.In this study,we fabricated two substrates of microcurvature(curvature-substrates)that present a smooth and repeating landscape with focuses of either a concave or a convex pattern.Using these curvature-substrates,we studied the properties of morphological differentiation in N2a neuroblastoma cells.In contrast to other studies where two-dimensional(2D)curvature was demonstrated to limit neurite outgrowth,we found that both the concave and convex substrates acted as continuous and uniform mechanical protrusions that significantly enhanced neural polarity and differentiation with few morphological changes in the main cell body.This enhanced differentiation was manifested in various properties,including increased neurite length,increased nuclear displacement,and upregulation of various neural markers.By demonstrating how the micron-scale curvature landscape induces neuronal polarity,we provide further insights into the design of biomaterials utilizing the influence of surface curvature in neural tissue engineering.

Variable Curvature Modeling Method of Soft Continuum Robots with Constraints

The inherent compliance of continuum robots holds great promise in the fields of soft manipulation and safe human–robot interaction.This compliance reduces the risk of damage to the manipulated object and its surroundings.However,continuum robots possess theoretically infinite degrees of freedom,and this high flexibility usually leads to complex deformations when subjected to external forces and positional constraints.Describing these complex deformations is the main challenge in modeling continuum robots.In this study,we investigated a novel variable curvature modeling method for continuum robots,considering external forces and positional constraints.The robot configuration curve is described using the developed mechanical model,and then the robot is fitted to the curve.A ten-section continuum robot prototype with a length of 1 m was developed in order to validate the model.The feasibility and accuracy of the model were verified by the ability of the robot to reach target points and track complex trajectories with a load.This work was able to serve as a new perspective for the design analysis and motion control of continuum robots.

Trimmable bandgap reference circuit with exponential curvature compensation

This paper proposes an improved exponential curvature-compensated bandgap reference circuit to exploit the exponential relationship between the current gainβof the bipolar junction transistor(BJT)and the temperature as well as reduce the influence of resistance-temperature dependency.Considering the degraded circuit performance caused by the process deviation,the trimmable module of the temperature coefficient(TC)is introduced to improve the circuit stability.The circuit has the advantages of simple structure,high linear stability,high TC accuracy,and trimmable TC.It consumes an area of 0.09 mm^(2)when fabricated by using the 0.25-μm complementary metal-oxide-semiconductor(CMOS)process.The proposed circuit achieves the simulated power supply rejection(PSR)of about-78.7 dB@1 kHz,the measured TC of~4.7 ppm/℃over a wide temperature range from-55℃to 125℃with the 2.5-V single-supply voltage,and the tested line regulation of 0.10 mV/V.Such a high-performance bandgap reference circuit can be widely applied in high-precision and high-reliability electronic systems.

Numerical simulation of a truncated cladding negative curvature fiber sensor based on the surface plasmon resonance effect

A refractive index(RI)sensor based on the surface plasmon resonance effect is proposed using a truncated cladding negative curvature fiber(TC-NCF).The influences of the TC-NCF structure parameters on the sensing performances are investigated and compared with the traditional NCF.The simulation results show that the proposed TC-NCF RI sensor has an ultra-wide detection range from 1.16 to 1.43.The maximum wavelength sensitivity reaches 12400 nm/RIU,and the corresponding R^(2)of the polynomial fitting equation is 0.9999.The maximum and minimum resolutions are 2.56×10^(-5)and 8.06×10^(-6),respectively.In addition,the maximum amplitude sensitivity can reach-379.1 RIU^(-1)when the RI is chosen as 1.43.The proposed TC-NCF RI sensor could be useful in biochemical medicine,environmental monitoring,and food safety.

GLOBAL RIGIDITY THEOREMS FOR SUBMANIFOLDS WITH PARALLEL MEAN CURVATURE

In this paper,we mainly study the global rigidity theorem of Riemannian submanifolds in space forms.Let Mn(n≥3)be a complete minimal submanifold in the unit sphere Sn+p(1).Forλ∈[0,n2−1/p),there is an explicit positive constant C(n,p,λ),depending only on n,p,λ,such that,if∫MSn/2dM<∞,∫M(S−λ)n/2+dM<C(n,p,λ),then Mn is a totally geodetic sphere,where S denotes the square of the second fundamental form of the submanifold and∫+=max{0,f}.Similar conclusions can be obtained for a complete submanifold with parallel mean curvature in the Euclidean space Rn+p.

Passability test and simulation of sand control string with natural gas hydrates completion in large curvature hole

To meet the requirements of marine natural gas hydrate exploitation,it is necessary to improve the penetration of completion sand control string in the large curvature borehole.In this study,large curvature test wells were selected to carry out the running test of sand control string with pre-packed screen.Meanwhile,the running simulation was performed by using the Landmark software.The results show that the sand control packer and screen can be run smoothly in the wellbore with a dogleg angle of more than 20°/30 m and keep the structure stable.Additionally,the comprehensive friction coefficient is 0.4,under which and the simulation shows that the sand control string for hydrate exploitation can be run smoothly.These findings have important guiding significance for running the completion sand control string in natural gas hydrate exploitation.

Creep age forming of 2124 aluminum alloy with single/double curvature

In order to investigate the springback rules, the variation characteristics of physical property and microstructure in bending creep age forming process, a series of creep forming tests of 2124 aluminum alloy were conducted based on three kinds of single and double curvature forming tools. The results show that the spingback rate would be the minimum under the optimal coupling conditions among the temperature, aging time and internal stress state of material. Difference exists in the two directions of the formed sample with double curvature, but the curvature variation keeps the same. Yield strength, ultimate tensile strength and fracture toughness of the double curvature formed sample appear to be higher than those of the single curvature formed sample under the same aging condition, but the elongation and the anisotropy are opposite.

A Near-1V 10ppm/℃ CMOS Bandgap Reference with Curvature Compensation

A low voltage bandgap reference with curvature compensation is presented. Using current mode structure, the proposed bandgap circuit has a minimum voltage of 900mV. Compensated through the VEB linearization technique, this bandgap reference can reach a temperature coefficient of 10ppmFC from 0 to 150℃. With a 1.1V supply voltage,the supply current is 43μA and the PSRR is 55dB at DC frequency. This bandgap reference has been verified in a UMC 0.18μm mixed mode CMOS technology and occupies 0. 186mm^2 of chip area.

FEM analysis of workpiece curvature influence on groove deformation during plough process

To investigate the workpiece curvature influence on groove deformation,numerical studies with curvature varying from negative to positive were conducted on copper material.Groove deformations were analyzed,including groove geometry,effective stress distribution and plough force.The curled groove shape whose workpiece curvature was 0.133 mm-1 was validated by experiments.Moreover,a series of geometry models with various curvatures were introduced to analyze the change of groove deformation.The results show that positive curvatures influence groove deformation more intensively than negative or zero curvature.It is mainly due to the action of the tool forming face during plough process.

The algorithm of 3D multi-scale volumetric curvature and its application

To fully extract and mine the multi-scale features of reservoirs and geologic structures in time/depth and space dimensions, a new 3D multi-scale volumetric curvature （MSVC） methodology is presented in this paper. We also propose a fast algorithm for computing 3D volumetric curvature. In comparison to conventional volumetric curvature attributes, its main improvements and key algorithms introduce multi-frequency components expansion in time-frequency domain and the corresponding multi-scale adaptive differential operator in the wavenumber domain, into the volumetric curvature calculation. This methodology can simultaneously depict seismic multi-scale features in both time and space. Additionally, we use data fusion of volumetric curvatures at various scales to take full advantage of the geologic features and anomalies extracted by curvature measurements at different scales. The 3D MSVC can highlight geologic anomalies and reduce noise at the same time. Thus, it improves the interpretation efficiency of curvature attributes analysis. The 3D MSVC is applied to both land and marine 3D seismic data. The results demonstrate that it can indicate the spatial distribution of reservoirs, detect faults and fracture zones, and identify their multi-scale properties.

一类Curvature方程的两种边值问题解的存在性

利用含有伪单调算子的变分不等式解的存在性定理,证明一类具有Dirichlet边值条件的Curvature方程在W1,p(Ω)空间中存在唯一解.深入研究具有Dirichlet边值条件的Curvature方程和具有Neumann边值条件的Curvature方程之间的关系,利用极大单调算子值域的扰动理论,给出具有Neumann边值条件的Curvature方程在W1,p(Ω)空间中存在解的充分条件.文中采用一些新的证明技巧,推广和补充了以往的相关研究成果.

无穷个增生映射和的半隐式算法、Ergodic收敛及Curvature系统（英文）

在实一致凸且q一致光滑Banach空间中,构造无穷个m增生映射和μ_i逆强增生映射和的公共零点的半隐式迭代算法.证明ergodic收敛性.与近期研究成果相比,限定条件更弱.此外,还研究了一类curvature系统并证明其解恰好是无穷个m增生映射和μ_i逆强增生映射和的公共零点,进而验证了迭代算法的有效性.

The Submanifolds with Parallel Mean Curvature Vector in a Locally Symmetric and Conformally Flat Riemannian Manifold

In the present paper we obtain the following result: Theorem Let M^R be a compact submanifold with parallel mean curvature vector in a locally symmetric and conformally flat Riemannian manifold N^(n+p)(p>1). If then M^n lies in a totally geodesic submanifold N^(n+1).

Synchro－Curvature Radiation──弯曲磁场中一种新的、更普遍的辐射

Ｓｙｎｃｈｒｏ－ＣｕｒｖａｔｕｒｅＲａｄｉａｔｉｏｎ──弯曲磁场中一种新的、更普遍的辐射张家铝（中国科技大学天体物理中心合肥２３００２６）郑广生（香港大学物理系）关键词同步辐射，曲率辐射，脉冲星磁层在脉冲星的辐射模型中，同步辐射和曲率辐射占有极其重要...