A novel method for simulating nuclear explosion with chemical explosion to form an approximate plane wave: Field test and numerical simulation

A nuclear explosion in the rock mass medium can produce strong shock waves,seismic shocks,and other destructive effects,which can cause extreme damage to the underground protection infrastructures.With the increase in nuclear explosion power,underground protection engineering enabled by explosion-proof impact theory and technology ushered in a new challenge.This paper proposes to simulate nuclear explosion tests with on-site chemical explosion tests in the form of multi-hole explosions.First,the mechanism of using multi-hole simultaneous blasting to simulate a nuclear explosion to generate approximate plane waves was analyzed.The plane pressure curve at the vault of the underground protective tunnel under the action of the multi-hole simultaneous blasting was then obtained using the impact test in the rock mass at the site.According to the peak pressure at the vault plane,it was divided into three regions:the stress superposition region,the superposition region after surface reflection,and the approximate plane stress wave zone.A numerical simulation approach was developed using PFC and FLAC to study the peak particle velocity in the surrounding rock of the underground protective cave under the action of multi-hole blasting.The time-history curves of pressure and peak pressure partition obtained by the on-site multi-hole simultaneous blasting test and numerical simulation were compared and analyzed,to verify the correctness and rationality of the formation of an approximate plane wave in the simulated nuclear explosion.This comparison and analysis also provided a theoretical foundation and some research ideas for the ensuing study on the impact of a nuclear explosion.

Explosion resistance performance of reinforced concrete box girder coated with polyurea:Model test and numerical simulation

To study the anti-explosion protection effect of polyurea coating on reinforced concrete box girder,two segmental girder specimens were made at a scale of 1:3,numbered as G(without polyurea coating)and PCG(with polyurea coating).The failure characteristics and dynamic responses of the specimens were compared through conducting explosion tests.The reliability of the numerical simulation using LS-DYNA software was verified by the test results.The effects of different scaled distances,reinforcement ratios,concrete strengths,coating thicknesses and ranges of polyurea were studied.The results show that the polyurea coating can effectively enhance the anti-explosion performance of the girder.The top plate of middle chamber in specimen G forms an elliptical penetrating hole,while that in specimen PCG only shows a very slight local dent.The peak vertical displacement and residual displacement of PCG decrease by 74.8% and 73.7%,respectively,compared with those of specimen G.For the TNT explosion with small equivalent,the polyurea coating has a more significant protective effect on reducing the size of fracture.With the increase of TNT equivalent,the protective effect of polyurea on reducing girder displacement becomes more significant.The optimal reinforcement ratio,concrete strength,thickness and range of polyurea coating were also drawn.

Tuning microstructures of TC4 ELI to improve explosion resistance

A reasonable heat treatment process for TC4 ELI titanium alloy is crucial to tune microstructures to improve its explosion resistance.However,there is limited investigation on tuning microstructures of TC4 ELI to improve explosion resistance.Moreover,the current challenge is quantifying microstructural changes'effects on explosion resistance and incorporating microstructural changes into finite element models.This work aims to tune microstructures to improve explosion resistance and elucidate their anti-explosion mechanism,and find a suitable method to incorporate microstructural changes into finite element models.In this work,we systematically study the deformation and failure characteristics of TC4 ELI plates with varying microstructures using an air explosion test and LS-DYNA finite element modeling.The Johnson-Cook(JC)constitutive parameters are used to quantify the effects of microstructural changes on explosion resistance and incorporate microstructural changes into finite element models.Because of the heat treatment,one plate has equiaxed microstructure and the other has bimodal microstructure.The convex of the plate after the explosion has a quadratic relationship with the charge mass,and the simulation results demonstrate high reliability,with the error less than 17.5%.Therefore,it is feasible to obtain corresponding JC constitutive parameters based on the differences in microstructures and mechanical properties and characterize the effects of microstructural changes on explosion resistance.The bimodal target exhibits excellent deformation resistance.The response of bimodal microstructure to the shock wave may be more intense under explosive loading.The well-coordinated structure of the bimodal target enhances its resistance to deformation.

Study on theoretical model for electrical explosion resistivity of Al/Ni reactive multilayer foil

Al/Ni reactive multilayer foil(RMF)possesses excellent comprehensive properties as a promising substitute for traditional Cu bridge.A theoretical resistivity model of Al/Ni RMF was developed to guide the optimization of EFIs.Al/Ni RMF with different bilayer thicknesses and bridge dimensions were prepared by MEMS technology and electrical explosion tests were carried out.According to physical and chemical reactions in bridge,the electrical explosion process was divided into 5 stages:heating of condensed bridge,vaporization and diffusion of Al layers,intermetallic combination reaction,intrinsic explosion,ionization of metal gases,which are obviously shown in measured voltage curve.Effects of interface and grain boundary scattering on the resistivity of film metal were considered.Focusing on variations of substance and state,the resistivity was developed as a function of temperature at each stage.Electrical explosion curves were calculated by this model at different bilayer thicknesses,bridge dimensions and capacitor voltages,which showed an excellent agreement with experimental ones.

Hydromechanical characterization of gas transport amidst uncertainty for underground nuclear explosion detection

Given the challenge of definitively discriminating between chemical and nuclear explosions using seismic methods alone,surface detection of signature noble gas radioisotopes is considered a positive identification of underground nuclear explosions(UNEs).However,the migration of signature radionuclide gases between the nuclear cavity and surface is not well understood because complex processes are involved,including the generation of complex fracture networks,reactivation of natural fractures and faults,and thermo-hydro-mechanical-chemical(THMC)coupling of radionuclide gas transport in the subsurface.In this study,we provide an experimental investigation of hydro-mechanical(HM)coupling among gas flow,stress states,rock deformation,and rock damage using a unique multi-physics triaxial direct shear rock testing system.The testing system also features redundant gas pressure and flow rate measurements,well suited for parameter uncertainty quantification.Using porous tuff and tight granite samples that are relevant to historic UNE tests,we measured the Biot effective stress coefficient,rock matrix gas permeability,and fracture gas permeability at a range of pore pressure and stress conditions.The Biot effective stress coefficient varies from 0.69 to 1 for the tuff,whose porosity averages 35.3%±0.7%,while this coefficient varies from 0.51 to 0.78 for the tight granite(porosity<1%,perhaps an underestimate).Matrix gas permeability is strongly correlated to effective stress for the granite,but not for the porous tuff.Our experiments reveal the following key engineering implications on transport of radionuclide gases post a UNE event:(1)The porous tuff shows apparent fracture dilation or compression upon stress changes,which does not necessarily change the gas permeability;(2)The granite fracture permeability shows strong stress sensitivity and is positively related to shear displacement;and(3)Hydromechanical coupling among stress states,rock damage,and gas flow appears to be stronger in tight granite than in porous tuff.

Explosion characteristics of aluminum-based activated fuels containing fluorine

Measuring the dust explosion characteristics of aluminum-based activated fuels was a prerequisite for developing effective prevention and control measures.In this paper,ignition sensitivity,flame propagation behaviors and explosion severity of aluminum/polytetrafluoroethylene(Al/PTFE)compositions including 2 PT(2.80 wt.%F),4 PT(7.18 wt.%F)and 8 PT(11.90 wt.%F)were studied.When the content of F increased from 2.80 wt.%to 11.90 wt.%,the minimum explosive concentration MEC decreased from380 g/m^(3)to 140 g/m^(3),due to the dual effects of increased internal active aluminum and enhanced reactivity.The average flame propagation velocities increased as the percentage of F increased.The maximum explosion pressure Pmof 500 g/m3aluminum-based activated fuels increased from 247 k Pa to299 kPa.Scanning electron microscopy demonstrated that with the increase of PTFE content,the reaction was more complete.On this basis,the explosion mechanism of aluminum-based activated fuels was revealed.

Modification of SDOF model for reinforced concrete beams under close-in explosion

In this paper,a modified single-degree-of-freedom(SDOF)model of reinforced concrete(RC)beams under close-in explosion is proposed by developing the specific impulse equivalent method and flexural resistance calculation method.The equivalent uniform specific impulse was obtained based on the local conservation of momentum and global conservation of kinetic energy.Additionally,the influence of load uniformity,boundary condition and complex material behaviors(e.g.strain rate effect,hardening/softening and hoop-confined effect)was considered in the resistance calculation process by establishing a novel relationship between external force,bending moment,curvature and deflection successively.The accuracy of the proposed model was verified by carrying out field explosion tests on four RC beams with the scaled distances of 0.5 m/kg~(1/3)and 0.75 m/kg~(1/3).The test data in other literatures were also used for validation.As a result,the equivalent load implies that the blast load near the mid-span of beams would contribute more to the maximum displacement,which was also observed in the tests.Moreover,both the resistance model and test results declare that when the blast load becomes more concentrated,the ultimate resistance would become lower,and the compressive concrete would be more prone to softening and crushing.Finally,based on the modified SDOF model,the calculated maximum displacements agreed well with the test data in this paper and other literatures.This work fully proves the rationality of the modified SDOF method,which will contribute to a more accurate damage assessment of RC structures under close-in explosion.

Experimental study of polyurea-coated fiber-reinforced cement boards under gas explosions

Five types of polyurea elastomers were synthesized by changing the isocyanate component and the mechanical properties of polyurea materials were measured. Fiber-reinforced cement boards(FRCB)strengthened by polyurea with different formulations were processed, and a series of experiments were carried out on the specimens with gas explosion devices. The results showed that the conventional mechanical properties of different types of polyureas had their own advantages. Based on the gas explosion overpressure criterion, the blast resistances of reinforced plates were quantitatively evaluated,and the best polyurea was selected to guide the formulation design. The three typical failure modes of polyurea-reinforced FRCBs were flexural, shear, and flexural-shear failure. Dynamic thermodynamics and shock wave spectral analysis revealed that the polyurea did not undergo a glass transition in the gas explosion tests but retained its elastic properties, allowing it to effectively wrap the fragments formed by the brittle substrates.

Numerical-Experimental Analysis of the Coal Fracture Formation Mechanism Induced by Liquid CO_(2) Explosion

The highly inefficient simultaneous extraction of coal and gas from low-permeability and high-gas coal seams in deep mines is a major problem often restricting the sustainable development of coal industry.A possible way to solve this problem under deep and complex geological conditions is represented by the technology based on the phase-change induced explosion of liquid carbon dioxide.In this work,the mechanism of formation of the coal mass fracture circle resulting from the gas cracking process is theoretically analyzed.Numerical simulations show that a blasting crushing zone with a radius of 1.0 m is formed around the blasting hole.The radius of the sec-ondary expansion zone caused by the exploding gas is 2.0 m,and the extension limit of the explosion fracture is 2.3 m.The gas phase change explosion is influenced by the coal roadway driving face,the gas content index and the analytical index of coal shavings.Experiments conducted for comparison also lead to the conclusion that the initial gas emission is increased by 3.7 times from the 100-meter borehole in the original coal mass after coalbed gas explosion anti-reflection.

Satellite breakup behaviors and model under the hypervelocity impact and explosion:A review

The primary causes of satellite breakups are hypervelocity impact and explosion,the research on satellite breakup can be used not only to evaluate the influence of breakup event on the space environment,but also to trace whether the satellite has been deliberately attacked.It is of great significance in both civil and military aspects.The study of satellite breakup behaviors and model is reviewed to summarize the research progress and insufficiency in recent decades,including the satellite breakup experiment,measurement and characterization of fragments,distribution characteristics of breakup fragments,satellite breakup model,etc.The classical studies are introduced in detail,and the limitations of the current research are pointed out.According to the current research results,the contemporary challenges and future directions for satellite breakup study are presented.The research on satellite breakup is developing in two directions:the miniaturization of satellite size and the complexity of satellite component.The study on satellite breakup needs to be explored and deepened on improving the experimental launch speed,expanding the model application range and breakup revealing the results under combined effect of impact and explosion.

Understanding the boundary and mechanism of gas-induced explosion for lithium-ion cells:Experimental and theoretical analysis

Thermal runaway(TR)of lithium-ion(Li-ion)batteries(LIBs)involves multiple forms of hazards,such as gas venting/jetting,fire,or even explosion.Explosion,as the most extreme case,is caused by the generated flammable gases,and a deflagration to detonation transition(DDT)may occur in this process.Here,overheat-to-TR tests and the corresponding outgas-induced explosion tests were conducted on 42 Ah Li-ion cells with Li[Ni_(1/3)Co_(1/3)Mn_(1/3)]O2cathode.The sum of CO_(2),H_(2),C_(2)H_(4),CO,and CH4accounted for more than 90%of the gases.Lower/upper explosion limits(LEL/UEL),laminar flame speed,and ideal stable detonation pressure were calculated to interpret the explosion characteristics and boundary.It turned out that shockwave was easily to be compressed and accelerated under higher state of charge(SOC)conditions.Thus,Li-ion cells explosion may evolve into unstable detonation in encapsulated battery pack and its evolution mechanism was explained,which provides a new idea for explosion-proof design of LIBs system.Additionally,a comprehensive assessment method was developed to intuitively characterize TR hazards.Severity of explosion presented an upward trend with the increase of SOC while the sensitivity was not the same.This study provides a further anatomy of TR,which is instructive to the safety of power battery systems.

Lead spall velocity of fragments of ultra-high-performance concrete slabs under partially embedded cylindrical charge-induced explosion

When an explosion occurs close to or partially within the face of a concrete structure, fragments are rapidly launched from the opposite face of the structure owing to concrete spalling, posing a significant risk to nearby personnel and equipment. To study the lead fragment velocity of ultra-high-performance concrete(UHPC), partially embedded explosion experiments were performed on UHPC slabs of limited thickness using a cylindrical trinitrotoluene charge. The launch angles and velocities of the resulting fragments were the determined using images collected by high-speed camera to document the concrete spalling and fragment launching process. The results showed that UHPC slabs without fiber reinforcement had a fragment velocity distribution of 0-118.3 m/s, which are largely identical to that for a normal-strength concrete(NSC) slab. In addition, the fragment velocity was negatively correlated to the angle between the velocity vector and vertical direction. An empirical Eq. for the lead spall velocity of UHPC and NSC slabs was then proposed based on a large volume of existing experimental data.

A nanoparticle formation model considering layered motion based on an electrical explosion experiment with AI wires

To study the evolution of nanoparticles during Al wire electrical explosion,a nanoparticle formation model that considered layered motion was developed,and an experimental system was set up to carry out electrical explosion experiments using 0.1 mm and 0.2 mm Al wires.The characteristic parameters and evolution process during the formation of nanoparticles were calculated and analyzed.The results show that the maximum velocities of the innermost and outermost layers are about 1200 m·s-1and 1600 m·s-1,and the velocity of the middle layer is about 1400 m·s-1,respectively.Most of the nanoparticles are formed in the temperature range of2600 K-2500 K.The characteristic temperature for the formation of Al nanoparticles is~2520K,which is also the characteristic temperature of other parameters.The size distribution range of the formed nanoparticles is 18 to 110 nm,and most of them are around 22 nm.The variation of saturated vapor pressure determines the temperature distribution range of particle nucleation.There is a minimum critical diameter of particles(~25 nm);particles smaller than the critical diameter can grow into larger particles during surface growth.Particle motion has an effect on the surface growth and aggregation process of particles,and also on the distribution area of larger-diameter particles.The simulation results are in good agreement with the experiments.We provide a method to estimate the size and distribution of nanoparticles,which is of great significance to understand the formation process of particles during the evolution of wire electrical explosion.

The damage to model concrete gravity dams subjected to water explosions

Over the past century,the safety of dams has gradually attracted attention from all parties.Research on the dynamic response and damage evolution of dams under extreme loads is the basis of dam safety issues.In recent decades,scholars have studied the responses of dams under earthquake loads,but there is still much room for improvement in experimental and theoretical research on small probability loads such as explosions.In this paper,a 50-m-high concrete gravity dam is used as a prototype dam,and a water explosion model test of a 2.5-m-high concrete gravity dam is designed.The water pressure and the acceleration response of the dam body in the test are analysed.The pressure characteristics and dynamic response of the dam body are assessed.Taking the dam damage test as an example,a numerical model of concrete gravity dam damage is established,and the damage evolution of the dam body is analysed.By combining experiments and numerical simulations,the damage characteristics of the dam body under the action of different charge water explosions are clarified.The integrity of the dam body is well maintained under the action of a small-quantity water explosion,and the dynamic response of the dam body is mainly caused by the shock wave.Both the shock wave and the bubble pulsation cause the dam body to accelerate,and the peak acceleration of the dam body under the action of the bubble pulsation is only one percent of the peak acceleration of the dam body under the action of the shock wave.When subjected to explosions in large quantities of water,the dam body is seriously damaged.Under the action of a shock wave,the dam body produces a secondary acceleration response,which is generated by an internal interaction after the dam body is damaged.The damage evolution process of the dam body under the action of a large-scale water explosion is analysed,and it is found that the shock wave pressure of the water explosion causes local damage to the dam body facing the explosion.After the peak value of the shock wave,the impulse continues to act on the dam body,causing cumulative damage and damage inside the dam body.

The Study on Bamboo Microfibers Isolated by Steam Explosion and Their Comprehensive Properties

To overcome the shortage of wood resources as well as to develop novel natural fibers materials,the Chimonobambusa quadrangularis(CQ)and Qiongzhuea tumidinoda(QT)planted in Southwest China were effectively isolated by the steam explosion(SE).The fine and uniform bamboo microfibers derived from CQ and QT were obtained,and their smallest average widths were 12.62μm and 16.05μm,respectively.The effects of steam explosion on the micro-morphology,chemical composition,thermal stability,crystallinity,surface wettability,and mechanical properties of bamboo microfibers were comprehensively investigated.The results showed that the relative content of cellulose in bamboo microfibers increased but the hemicellulose and lignin contents decreased after SE.The degrees of crystallinity for CQ and QT increased from 40.49%and 39.46%to 68.90%and 55.78%,respectively.The thermal stability and surface hydrophilicity were also improved.The CQ microfibers had a maximum decomposition temperature of 2.79°C,a tensile strength of 58.54 MPa,an elongation at break of 0.6%,and a water contact angle of 2.7°higher than those of the QT microfibers.

Blast resistance of air-backed RC slab against underwater contact explosion

Reinforced concrete(RC)structures are common in engineering,and usually exposed to air or water,may be subjected to various blast scenarios.This paper aims to investigate the blast resistance of an airbacked RC slab against underwater contact explosions(UWCEs).A detailed numerical model based on CLE method considering explosive,water,air,and RC slab is developed to examine the structural behavior of the air-backed RC slab due to UWCEs.At first,the reliability of the numerical method is validated by comparing the numerical results of an UWCE test with experimental data.Then,the difference in dynamic behavior of air-backed and water-backed RC slabs due to UWCEs is explored with the calibrated model.The results indicate that the blast response of the air-backed slab induced by UWCE is fiercer than that of water-backed slab with equal charge mass.In addition,parametric studies are also conducted to explore the effects of the charge mass,standoff distance,reinforcement spacing,concrete compression strength,and boundary condition on the blast performance of the air-backed RC slab.

Explosion Event of Cavitation in Intact Xylem Conduit

Cavitation in plant conduits only involves two processes of air bubbles: the gradual expansion and elongation, and the explosion event. An explosion event of cavitation, which can only occur in intact conduit at water tension, trigs acoustic (or ultrasound) emission and induces air to diffuse with high speed, simultaneously. Synchrotron X-ray phase contrast microscopy (XPCM) was used to capture cavitation event in intact conduits of leaves of corn and rice. Cavitation events occur in certain areas of leaves and have a certain time frame. Before XPCM experiment, several preliminary experiments were done as follows: 1) Paraffin sections of leaves of different species were observed to select samples and to determine the occurrence area of cavitation event of leaves. 2) The time frame of cavitation occurrence was determined by ultrasonic emission. 3) The water potentials of leaves were determined, to know the water state of the leaves during cavitation. Locked the area and time frame of cavitation event in the leaves, consecutive XPCM images of cavitation process were more easily acquired. The images show that the phenomenon of gas bubble fully filling conduits for an instant took place in intact conduits of detached leaves of corn and rice more easily. It is that the gas diffusing in a moment was caused by the explosion of the air seeds which had entered in the intact conduits of the leaves. For living plants, it is suggested that the explosion event of cavitation is the most important for embolism formation.

Effects of Rice Straw Steam-explosion Spent Liquor on the Growth of Cabbage Seedlings

The direct use of spent liquor from pulping and papermaking engineering,which is abundant in active organic matter,can avoid resource wastage and environmental pollution.In this study,the effects of soaking solution and filtrate from steam-exploded rice straw on seed germination and the early development of cabbage were investigated.The results have shown that soaking solution and filtrate stimulated early cabbage growth at low concentrations.Optimal germination potential and the rate of soaking solution-treated cabbage seeds increased by 8%and 5%,respectively;meanwhile,that of the filtrate-treated cabbage seeds increased by 11%and 5%,respectively.Promotion of root growth by steam-exploded rice straw spent liquor was expressed in lateral root multiplication.The fresh weight of cabbage seedlings treated with the soaking solution/filtrate increased by more than 50%and the dry weight over 20%.Comparatively,the stimulation of filtrate on seed germination and early development of cabbage is superior to that of the soaking solution.Steam-exploded rice straw spent liquor is rich in bioactive lignin and oligosaccharides,which makes it a promising biostimulant for promoting crop growth.

Evidence for Large Planetary Climate Altering Thermonuclear Explosions on Mars in the Past

Mars data presents a collection of startling and seemly contradictory isotopic data: a glaring excess of the two radiogenic isotopes 129Xe/132Xe @ 2.5 and 40Ar/36Ar @ 3000 enabled identification of MM (Mars Meteorites) because they are so different than any other major Solar System reservoir. Mars appears to have lost an original atmosphere of pressure 1 bar or greater, yet the ratio 14N/15N indicates only a loss of a few millibar by Solar Wind Erosion. The LPARE (Large Planet Altering R-process Event) hypothesis attempts to explain these major isotopic puzzles at Mars by postulating that two massive, anomalous thermonuclear explosions, rich in R-process physics, occurred over the surface of Northern Mars in the past, approximately 500 million years ago, and that these explosions created the 129Xe/132Xe excess, and the accompanying intense neutron bombardment of Mars atmosphere and regolith created the 40Ar/36Ar excess off of potassium in the surface rocks. The collateral massive and non-mass fractionating atmospheric loss, and the intense neutron bombardment of 14N in the atmosphere primarily created the 14N/15N ratio we presently observe, with some mass fractionating erosion of the residual atmosphere. This LPARE hypothesis is found to explain other isotopic features of Mars atmosphere and surface. 80Kr and 82Kr are hyperabundant in the Mars atmosphere and in the youngest MMs indicating intense irradiation of Mars surface with neutrons. Although there is presently no plausible explanation for the nuclear events, the hypothesis can be tested through related nuclear products such as Pu-244.

A historical overview of nano-optics:From near-field optics to plasmonics

Nano-optics is an emergent research field in physics that appeared in the 1980s,which deals with light–matter optical interactions at the nanometer scale.In early studies of nano-optics,the main concern focus is to obtain higher optical resolution over the diffraction limit.The researches of near-field imaging and spectroscopy based on scanning near-field optical microscopy(SNOM)are developed.The exploration of improving SNOM probe for near-field detection leads to the emergence of surface plasmons.In the sense of resolution and wider application,there has been a significant transition from seeking higher resolution microscopy to plasmonic near-field modulations in the nano-optics community during the nano-optic development.Nowadays,studies of nano-optics prefer the investigation of plasmonics in different material systems.In this article,the history of the development of near-field optics is briefly reviewed.The difficulties of conventional SNOM to achieve higher resolution are discussed.As an alternative solution,surface plasmons have shown the advantages of higher resolution,wider application,and flexible nano-optical modulation for new devices.The typical studies in different periods are introduced and characteristics of nano-optics in each stage are analyzed.In this way,the evolution progress from near-field optics to plasmonics of nano-optics research is presented.The future development of nano-optics is discussed then.