Investigation of Groundwater Quality with Borehole Depth in the Basin Granitoids of the Ashanti Region of Ghana

The dependence of groundwater quality on borehole depth is usually debatable in groundwater studies, especially in complex geological formations where aquifer characteristics vary spatially with depth. This study therefore seeks to investigate the relationship between borehole depth and groundwater quality across the granitoid aquifers within the Birimian Supergroup in the Ashanti Region. Physicochemical analysis records of groundwater quality data were collected from 23 boreholes of public and private institutions in the Ashanti Region of Ghana, and the parametric values of iron, fluoride, total hardness, pH, nitrate, and nitrite were used to study the groundwater quality-depth relationship. The results showed that the depth-to-groundwater quality indicated a marginal increase in water quality in the range of 30 to 50 m, which is mathematically represented by the low-value correlation coefficient (r2 = 0.026). A relatively significant increase occurs in the depth range of 50 to 80 m, which is given by a correlation coefficient of r2 = 0.298. The mean percent parameter compatibility was 74%, 82%, 89%, and 97% at 50, 60, 70, and 80 m depths, respectively. The variations in groundwater quality per depth ratio ranged from 1.48, 1.37, 1.27, and 1.21 for 50, 60, 70, and 80 m depth, respectively. The recommended minimum borehole depth for excellent groundwater quality is suggested with a compatibility per meter depth ratio of 1.37. This results in a range between 50 and 70 m as the most desirable drilling depth for excellent groundwater quality within the granitoids of the Birimian Supergroup of the Ashanti Region in Ghana.

Inverting the rock mass P-wave velocity field ahead of deep buried tunnel face while borehole drilling

Imaging the wave velocity field surrounding a borehole while drilling is a promising and urgently needed approach for extending the exploration range of the borehole point.This paper develops a drilling process detection(DPD)system consisting of a multifunctional sensor and a pilot geophone installed at the top of the drilling rod,geophones at the tunnel face,a laser rangefinder,and an onsite computer.A weighted adjoint-state first arrival travel time tomography method is used to invert the P-wave velocity field of rock mass while borehole drilling.A field experiment in the ongoing construction of a deep buried tunnel in southwestern China demonstrated the DPD system and the tomography method.Time-frequency analysis of typical borehole drilling detection data shows that the impact drilling source is a pulse-like seismic exploration wavelet.A velocity field of the rock mass in a triangular area defined by the borehole trajectory and geophone receiving line can be obtained.Both the borehole core and optical image validate the inverted P-wave velocity field.A numerical simulation of a checkerboard benchmark model is used to test the tomography method.The rapid convergence of the misfits and consistent agreement between the inverted and observed travel times validate the P-wave velocity imaging.

Fracture geometry and breakdown pressure of radial borehole fracturing in multiple layers

Radial borehole fracturing that combines radial boreholes with hydraulic fracturing is anticipated to improve the output of tight oil and gas reservoirs.This paper aims to investigate fracture propagation and pressure characteristics of radial borehole fracturing in multiple layers.A series of laboratory experiments with artificial rock samples(395 mm×395 mm×395 mm)was conducted using a true triaxial fracturing device.Three crucial factors corresponding to the vertical distance of adjacent radial borehole layers(vertical distance),the azimuth and diameter of the radial borehole are examined.Experimental results show that radial borehole fracturing in multiple layers generates diverse fracture geometries.Four types of fractures are identified based on the connectivity between hydraulic fractures and radial boreholes.The vertical distance significantly influences fracture propagation perpendicular to the radial borehole axis.An increase in the vertical distance impedes fracture connection across multiple radial borehole layers and reduces the fracture propagation distance along the radial borehole axis.The azimuth also influences fracture propagation along the radial borehole axis.Increasing the azimuth reduces the guiding ability of radial boreholes,which makes the fracture quickly curve to the maximum horizontal stress direction.The breakdown pressure correlates with diverse fracture geometries observed.When the fractures connect multi-layer radial boreholes,increasing the vertical distance decreases the breakdown pressure.Decreasing the azimuth and increasing the diameter also decrease the breakdown pressure.The extrusion force exists between the adjacent fractures generated in radial boreholes in multiple rows,which plays a crucial role in enhancing the guiding ability of radial boreholes and results in higher breakdown pressure.The research provides valuable theoretical insights for the field application of radial borehole fracturing technology in tight oil and gas reservoirs.

Effects of confining pressure and pore pressure on multipole borehole acoustic field in fluid-saturated porous media

In-situ stress is a common stress in the exploration and development of oil reservoirs. Therefore, it is of great significance to study the propagation characteristics of borehole acoustic waves in fluid-saturated porous media under stress.Based on the acoustoelastic theory of fluid-saturated porous media, the field equation of fluid-saturated porous media under the conditions of confining pressure and pore pressure and the acoustic field formula of multipole source excitation in open hole are given. The influences of pore pressure and confining pressure on guided waves of multipole borehole acoustic field in fluid-saturated porous media are investigated. The numerical results show that the phase velocity and excitation intensity of guided wave increase significantly under the confining pressure. For a given confining pressure, the phase velocity of the guided wave decreases with pore pressure increasing. The excitation intensity of guided wave increases at low frequency and then decreases at high frequency with pore pressure increasing, except for that of Stoneley wave which decreases in the whole frequency range. These results will help us get an insight into the influences of confining pressure and pore pressure on the acoustic field of multipole source in borehole around fluid-saturated porous media.

Research on High Precision Borehole Temperature Measurement Technology

From 2019 to 2021,China Seismic Experimental Site has built twelve 300 m deep well multi-measurement comprehensive observation stations in the cross-fault area of the Aninghe-Zemuhe fault zone,integrating BBVS120 very broadband borehole seismometer,RZB four-gauge borehole strainmeter and geothermometer with resolution up to 0.0001℃.The borehole diameter is 150 mm and the inner diameter of the sleeve is 130 mm.The multi-item integrated observation system is divided into two parts:underground and surface.The downhole part is mainly composed of sensor and power supply signal isolation.

CO_(2)flooding in shale oil reservoir with radial borehole fracturing for CO_(2)storage and enhanced oil recovery

This study introduces a novel method integrating CO_(2)flooding with radial borehole fracturing for enhanced oil recovery and CO_(2)underground storage,a solution to the limited vertical stimulation reservoir volume in horizontal well fracturing.A numerical model is established to investigate the production rate,reservoir pressure field,and CO_(2)saturation distribution corresponding to changing time of CO_(2)flooding with radial borehole fracturing.A sensitivity analysis on the influence of CO_(2)injection location,layer spacing,pressure difference,borehole number,and hydraulic fractures on oil production and CO_(2)storage is conducted.The CO_(2)flooding process is divided into four stages.Reductions in layer spacing will significantly improve oil production rate and gas storage capacity.However,serious gas channeling can occur when the spacing is lower than 20 m.Increasing the pressure difference between the producer and injector,the borehole number,the hydraulic fracture height,and the fracture width can also increase the oil production rate and gas storage rate.Sensitivity analysis shows that layer spacing and fracture height greatly influence gas storage and oil production.Research outcomes are expected to provide a theoretical basis for the efficient development of shale oil reservoirs in the vertical direction.

Performance analysis of deep borehole heat exchangers for decarbonization of heating systems

Meeting the climate change mitigation targets will require a substantial shift from fossil to clean fuels in the heating sector.Heat pumps with deep borehole exchangers are a promising solution to reduce emissions.Here the thermal behavior of deep borehole exchangers(DBHEs)ranging from 1 to 2 km was analyzed for various heat flow profiles.A strong correlation between thermal energy extraction and power output from DBHEs was found,also influenced by the heating profile employed.Longer operating time over the year typically resulted in higher energy production,while shorter one yielded higher average thermal power output,highlighting the importance of the choice of heating strategy and system design for optimal performance of DBHEs.Short breaks in operation for regenerating the borehole,for example,with waste heat,proved to be favorable for the performance yielding an overall heat output close to the same as with continuous extraction of heat.The results demonstrate the usefulness of deep boreholes for dense urban areas with less available space.As the heat production from a single DBHE in Finnish conditions ranges from half up to even a few GWh a year,the technology is best suitable for larger heat loads.

Method for evaluation of geological strength index of carbonate cliff rocks:Coupled hyperspectral-digital borehole image technique

The deterioration of unstable rock mass raised interest in evaluating rock mass quality.However,the traditional evaluation method for the geological strength index(GSI)primarily emphasizes the rock structure and characteristics of discontinuities.It ignores the influence of mineral composition and shows a deficiency in assessing the integrity coefficient.In this context,hyperspectral imaging and digital panoramic borehole camera technologies are applied to analyze the mineral content and integrity of rock mass.Based on the carbonate mineral content and fissure area ratio,the strength reduction factor and integrity coefficient are calculated to improve the GSI evaluation method.According to the results of mineral classification and fissure identification,the strength reduction factor and integrity coefficient increase with the depth of rock mass.The rock mass GSI calculated by the improved method is mainly concentrated between 40 and 60,which is close to the calculation results of the traditional method.The GSI error rates obtained by the two methods are mostly less than 10%,indicating the rationality of the hyperspectral-digital borehole image coupled evaluation method.Moreover,the sensitivity of the fissure area ratio(Sr)to GSI is greater than that of the strength reduction factor(a),which means the proposed GSI is suitable for rocks with significant fissure development.The improved method reduces the influence of subjective factors and provides a reliable index for the deterioration evaluation of rock mass.

Borehole stability in naturally fractured rocks with drilling mud intrusion and associated fracture strength weakening:A coupled DFN-DEM approach

Borehole instability in naturally fractured rocks poses significant challenges to drilling.Drilling mud invades the surrounding formations through natural fractures under the difference between the wellbore pressure(P w)and pore pressure(P p)during drilling,which may cause wellbore instability.However,the weakening of fracture strength due to mud intrusion is not considered in most existing borehole stability analyses,which may yield significant errors and misleading predictions.In addition,only limited factors were analyzed,and the fracture distribution was oversimplified.In this paper,the impacts of mud intrusion and associated fracture strength weakening on borehole stability in fractured rocks under both isotropic and anisotropic stress states are investigated using a coupled DEM(distinct element method)and DFN(discrete fracture network)method.It provides estimates of the effect of fracture strength weakening,wellbore pressure,in situ stresses,and sealing efficiency on borehole stability.The results show that mud intrusion and weakening of fracture strength can damage the borehole.This is demonstrated by the large displacement around the borehole,shear displacement on natural fractures,and the generation of fracture at shear limit.Mud intrusion reduces the shear strength of the fracture surface and leads to shear failure,which explains that the increase in mud weight may worsen borehole stability during overbalanced drilling in fractured formations.A higher in situ stress anisotropy exerts a significant influence on the mechanism of shear failure distribution around the wellbore.Moreover,the effect of sealing natural fractures on maintaining borehole stability is verified in this study,and the increase in sealing efficiency reduces the radial invasion distance of drilling mud.This study provides a directly quantitative prediction method of borehole instability in naturally fractured formations,which can consider the discrete fracture network,mud intrusion,and associated weakening of fracture strength.The information provided by the numerical approach(e.g.displacement around the borehole,shear displacement on fracture,and fracture at shear limit)is helpful for managing wellbore stability and designing wellbore-strengthening operations.

Analytical investigations of in situ stress inversion from borehole breakout geometries

This study aims to investigate the feasibility of deriving in situ horizontal stresses from the breakout width and depth using the analytical method.Twenty-three breakout data with different borehole sizes were collected and three failure criteria were studied.Based on the Kirsch equations,relatively accurate major horizontal stress(sH)estimations from known minor horizontal stress(sh)were achieved with percentage errors ranging from 0.33%to 44.08%using the breakout width.The Mogi-Coulomb failure criterion(average error:13.1%)outperformed modified Wiebols-Cook(average error:19.09%)and modified Lade(average error:18.09%)failure criteria.However,none of the tested constitutive models could yield reasonable sh predictions from known sH using the same approach due to the analytical expression of the redistributed stress and the nature of the constitutive models.In consideration of this issue,the horizontal stress ratio(sH/sh)is suggested as an alternative input,which could estimate both sH and sh with the same level of accuracy.Moreover,the estimation accuracies for both large-scale and laboratory-scale breakouts are comparable,suggesting the applicability of this approach across different breakout sizes.For breakout depth,conformal mapping and complex variable method were used to calculate the stress concentration around the breakout tip,allowing the expression of redistributed stresses using binomials composed of sH and sh.Nevertheless,analysis of the breakout depth stabilisation mechanism indicates that additional parameters are required to utilise normalised breakout depth for stress estimation compared to breakout width.These parameters are challenging to obtain,especially under field conditions,meaning utilising normalised breakout depth analytically in practical applications faces significant challenges and remains infeasible at this stage.Nonetheless,the normalised breakout depth should still be considered a critical input for any empirical and statistical stress estimation method given its significant correlation with horizontal stresses.The outcome of this paper is expected to contribute valuable insights into the breakout stabilisation mechanisms and estimation of in situ stress magnitudes based on borehole breakout geometries.

Impact of elliptical boreholes on in situ stress estimation from leak-off test data

We developed an inversion technique to determine in situ stresses for elliptical boreholes of arbitrary trajectory. In this approach, borehole geometry, drilling-induced fracture information, and other available leak-off test data were used to construct a mathematical model, which was in turn applied to finding the inverse of an overdetermined system of equations.The method has been demonstrated by a case study in the Appalachian Basin, USA. The calculated horizontal stresses are in reasonable agreement with the reported regional stress study of the area, although there are no field measurement data of the studied well for direct calibration. The results also indicate that 2% of axis difference in the elliptical borehole geometry can cause a 5% difference in minimum horizontal stress calculation and a 10% difference in maximum horizontal stress calculation.

STABILITY OF BOREHOLES IN A GEOLOGIC MEDIUM INCLUDING THE EFFECTS OF ANISOTROPY

An analytical formulation is developed to investigate the stability of a deep, inclined borehole drilled in a geologic medium and subjected to an internal pressure and a non_hydrostatic stress field. The formulation consists of a three_dimensional (3_D) analysis of stresses around a borehole, combined with internal pressurization of the borehole to obtain an approximate solution of the overall stress distribution. The orientation of the borehole, the in_situ stresses and bedding plane can all be arbitrarily related to each other to represent the actual field situations. Both tensile failure and shear failure potentials of a borehole are investigated. The failure criteria applied assume that when the least principal stress exceeds the strength of the formation in tension, a tensile failure occurs. Shear failure is represented using the modified Drucker_Prager failure criterion for anisotropic materials. A parametric study is carried out to assess the effect of material anisotropy, bedding plane inclination and in_situ stress conditions on borehole stability. Results of the parametric study indicate that wellbore stability is significantly influenced by a high borehole inclination, high degree of material anisotropy, in_situ stress conditions and high formation bedding plane inclination. The stability of a borehole in an elasto_plastic medium is also investigated. In order to evaluate the extent of the plastic zone around a borehole and the effect of anisotropy of the material on this plastic zone, a mathematical formulation is developed using theories of elasticity and plasticity. The borehole is assumed to be vertical, subjected to hydrostatic stresses, and drilled in a transversely isotropic geologic medium. A parametric study is carried out to investigate the effect of material anisotropy on the plastic behavior of the geologic medium. Results indicate that the stress distribution around a borehole, the extent of the plastic zone, and the failure pressure are influenced by the degree of material anisotropy and value of in_situ overburden stresses. It was observed that the borehole becomes less stable as the degree of anisotropy of the geologic medium increases.

Safety analysis of stability of surface gas drainage boreholes above goaf areas

As longwall caving mining method prevails rapidly in China coal mines, amount of gas emission from longwall faces and goaf area increased significantly. Using traditional gas drainage methods, such as drilling upward holes to roof strata in tailgate or drilling inseam and cross-measure boreholes, could not meet methane drainage requirements in a gassy mine. The alternative is to drill boreholes from surface down to the Iongwall goaf area to drain the gas out. As soon as a coal seam is extracted out, the upper rock strata above the goaf start to collapse or become fractured depending upon the rock characteristics and the height above the coal seam. During overlying rock strata being fractured, boreholes in the area may be damaged due to ground movement after the passage of the Iongwall face. The sudden damage of a borehole may cause a Iongwall production halt or even a serious mine accident. A theoretical calculation of the stability of surface boreholes in mining affected area is introduced along with an example of determination of borehole and casing diameters is given for demonstration. By using this method for the drilling design, the damage of surface boreholes caused by excessive mining induced displacement can be effectively reduced if not totally avoided. Borehole and casing diameters as well as characteristics of filling materials can be determined using the proposed method by calculating the horizontal movement and vertical stain at different borehole depths.

Inversion of breakout data from inclined boreholes for stress state of the upper crust in Jizhong depression

The forward and inverse problems of studying crustal stress state from breakout data of inclined boreholes are concisely stated. direction of the maximum horizontal principal stress (compressive) and relative magnitudes of the horizontal stresses to the vertical stress in the upper crust in two regions of the Jizhong depression, the North of China, are obtained by analyzing the breakout data of 6 inclined wells. To get stable results in the analysis wesearched for the unknown parameters both forwardly and inversely. The results show that the maximum azimuths of the horizontal Principal compressive stresses in the central and southern part of the Jizhong depressionare N86°E and N77°E, respeCtively, while the relative magnitudes of the three principal stresses in the uppercrust (about 1000-4000 m) of the depression are variable. In the centra; part of the Jizhong depression we havefound SH : Sv: SK= 1. 38: 1. 00: 0. 57, where SH, SV and Sh are the maximum horizontal, vertical and minimum horizontal stress, resistively. This indicates that the present stress regime in this area is of strike-slipfaulting type. In the southern part of the depreSSion we have obtained SH: Sv: Sh=0. 80: 1. 00 1 0. 62, indicating a normal faulting stress regime in the shallow Part Of the crust.

Thermo-hydro-mechanical coupled mathematical model for controlling the pre-mining coal seam gas extraction with slotted boreholes

Drainage influence radius is the basic parameter for borehole arrangement, while the effect of high pressure water jet slotting technology on borehole drainage influence radius has not been studied systematically. In this paper, a fully thermo-hydro-mechanical(THM) coupled model which represents the non-linear responses of gas extraction was implemented to demonstrate the reliability of this model through history data matching. Based on this model, the susceptibilities of gas extraction with single slotted borehole, including the permeability, the gas pressure, the temperature, the coal adsorption characteristics and the radius of slot, were quantified through a series of simulations. The simulation results revealed that increasing the permeability, initial gas pressure and temperature could develop the influence radius of single slotted borehole. This finite element model and its simulation results can improve the understanding of the coal-gas interactions of underground gas drainage and provide a scientific basis for the optimization of drainage systems.

Influence of combination forms of intact sub-layer and tectonically deformed sub-layer of coal on the gas drainage performance of boreholes: a numerical study

High concentration and large flow flux of gas drainage from underground coal seams is the precondition of reducing emission and large-scale use of gas.However,the layered occurrence of coal seams with tectonically deformed sub-layers and intact sub-layers makes it difficult to effectively drain gas through commonly designed boreholes.In this study,the gas drainage performance in coal seams with different combinations of tectonically deformed sub-layers and intact sub-layers was numerically analyzed.The analysis results show that the gas drainage curve changes from a single-stage line to a dual-stage curve as the permeability ratios of Zone II(kII)and Zone I(kI)increase,raising the difficulty in gas drainage.Furthermore,a dual-system pressure decay model based on the first-order kinetic model was developed to describe the dual-stage characteristics of pressure decay curves with different permeability ratios.In the end,the simulation results were verified with reference to in-situ drainage data from literature.The research results are helpful for mines,especially those with layered coal seams comprising tectonically deformed sub-layers and intact sub-layers,to choose appropriate gas drainage methods and develop the original drainage designs for achieving better gas drainage performance.

Antimicrobial Resistance Profile of Bacteria Isolated from Boreholes and Hand Dug Wells Water in Ngaoundere Municipality of Adamawa Region in Cameroon

Uncontrolled uses of antibiotics have led to rapid evolution of antibiotic-resistance bacteria and antibiotic resistance gene transfer, especially in a pool of aquatic system where resistance, intermediate and susceptible bacteria to some antibiotics strive together. Consequently, there is a transfer of resistance genes. In this study, bacteria of the Enterobacteriaceae family and some gram positive bacteria isolated from some boreholes and hand dug wells water of public use were tested on 19 antibiotics of different classes. This was achieved through a disk diffusion technique to determine the antimicrobial resistance profile of the said bacteria, microbial resistance index of the drugs used (and their ability to produce Beta-lactamase). These isolates were shown to demonstrate a very high resistance to the drugs used in the area. The resistance was highest in Escherichia coli 1 (73.68%) and lowest in Streptococcus pneumoniae (47.82%). These isolates also indicated very high levels of multi-drug resistance. The minimum resistance index was 0.47, indicating that bacteria isolates were of fecal origin. It is evident from the present study that multiple antibiotic-resistant bacteria can thrive in water as an environmental reservoir, and can therefore provide a route to multidrug-resistant pathogens to enter human and animal population.

Method for designing the optimal sealing depth in methane drainage boreholes to realize efficient drainage

The purpose of underground methane drainage technology is to prevent methane disasters and enable the efficient use of coal mine methane(CMM),and the sealing depth is a key factor that affects the performance of underground methane drainage.In this work,the layouts of in-seam and crossing boreholes are considered to analyze the stress distribution and failure characteristics of roadway surrounding rock through a numerical simulation and field stress investigation to determine a reasonable sealing depth.The results show that the depths of the plastic and elastic zones in two experimental coal mines are 16 and 20 m respectively.Borehole sealing minimizes the air leakage through the fractures around the roadway when the sealing material covers the failure and plastic zones,and the field test results for CMM drainage at different sealing depths indicate that the CMM drainage efficiency increases with increasing sealing depth but does not change once the sealing depth exceeds the plastic zone.Moreover,sealing in the high-permeability roadway surrounding rock does not have a strong influence on the borehole sealing performance.Considering these findings,a new CMM drainage system for key sealing in the low-permeability zone was developed that is effective for improving the CMM drainage efficiency and prolonging the high-concentration CMM drainage period.The proposed approach offers a valuable quantitative analysis method for selecting the optimum sealing parameters for underground methane drainage,thereby improving considerably the drainage and utilization rates of CMM.

Optimization of gob ventilation boreholes design in longwall mining

Gob ventilation boreholes(GVBs)are widely used for degasification in U.S.longwall coal mines.Depending on geological conditions,30–50%of methane can be recovered from longwall gob using GVBs.A NIOSH funded research at the Colorado School of Mines confirmed that GVBs can efficiently reduce methane at the face.However,GVBs can also draw some fresh air from the face and create explosive gas zones(EGZs).Explosive gas mixtures may be formed in gob areas due to the increased ingress of oxygen from GVBs.It is critical to identify the locations for GVBs for maximizing extraction of methane and minimizing hazards of explosion.This study analyzes the effect of operating parameters and design of GVB on methane extraction,EGZs formation,and face and tailgate methane concentrations.Methane extraction,formation of EGZs,and concentration of methane in working areas are significantly impacted by various factors.These factors include the distance of work face and tailgate from GVBs,diameter of GVBs,vacuum pressure of wellhead,GVB distance from the roof of the coal seam,and number of operating GVBs in a panel.Computational fluid dynamics(CFD)evaluations suggest optimal design and operating parameters of GVBs that can contribute to maximum benefits with minimum risks.

Water Analysis for Heavy Metals Content in Selected Boreholes in Port Harcourt Metropolis （A Case Study during 2010-2011）

Underground water （Borehole） has been the main alternative source of drinking water for most communities in my country. Previous studies have revealed high levels of contamination. The origin of which can be attributed to geochemical processes, combustion of fossil fuels, mining and anthropogenic activities. Most borehole water and well water in local communities of Nigeria are not safe for drinking due to heavy industrial and environmental pollution. This study was undertaken to assess the quality in some selected boreholes in the Port Harcourt metropolis for a period of two years. Borehole water samples were randomly collected from thirteen boreholes in a local community in plastic bottles （100 mL） in the months of September for the years of study （2010 ＆ 2011）. Four out of the seven heavy metals analyzed were found to be present in the first year of study. These were Fe, Cu, Mn and Zn. In the second year of study, Pb, Cr, Fe and Co were not detected in all of the samples except Cu and Fe which were present in only two samples. Mn and Zn were found to be present in all of the samples for both years of study.