Highly Active Interfacial Sites in SFT-SnO_(2) Heterojunction Electrolyte for Enhanced Fuel Cell Performance via Engineered Energy Bands:Envisioned Theoretically and Experimentally

Extending the ionic conductivity is the pre-requisite of electrolytes in fuel cell technology for high-electrochemical performance.In this regard,the introduction of semiconductor-oxide materials and the approach of heterostructure formation by modulating energy bands to enhance ionic conduction acting as an electrolyte in fuel cell-device.Semiconductor(n-type;SnO_(2))plays a key role by introducing into p-type SrFe_(0.2)Ti_(0.8)O_(3-δ)(SFT)semiconductor perovskite materials to construct p-n heterojunction for high ionic conductivity.Therefore,two different composites of SFT and SnO_(2)are constructed by gluing p-and n-type SFT-SnO_(2),where the optimal composition of SFT-SnO_(2)(6∶4)heterostructure electrolyte-based fuel cell achieved excellent ionic conductivity 0.24 S cm^(-1)with power-output of 1004 mW cm^(-2)and high OCV 1.12 V at a low operational temperature of 500℃.The high power-output and significant ionic conductivity with durable operation of 54 h are accredited to SFT-SnO_(2)heterojunction formation including interfacial conduction assisted by a built-in electric field in fuel cell device.Moreover,the fuel conversion efficiency and considerable Faradaic efficiency reveal the compatibility of SFT-SnO_(2)heterostructure electrolyte and ruled-out short-circuiting issue.Further,the first principle calculation provides sufficient information on structure optimization and energy-band structure modulation of SFT-SnO_(2).This strategy will provide new insight into semiconductor-based fuel cell technology to design novel electrolytes.

Manipulation of High-Fidelity Sidebands under Large Detuning by Floquet Technology:Application to Multi-Mode Cooling

The Floquet technology,a powerful way to manipulate quantum states,is employed to drive sidebands transition under large detuning.Our results demonstrate that high fidelities over 99%can be achieved through optimizing suitable modulation frequencies under large detuning.We observe high-fidelity transitions within a high bandwidth by utilizing a single modulation frequency and reveal that this capability is due to the emergence of a flat-band structure in the bandwidth range.The key finding of high-fidelity sideband manipulation under large detuning is experimentally confirmed in nuclear magnetic resonance platform.Finally,we propose a new parallel sideband cooling scheme that enables simultaneous cooling of multiple motional modes.This approach improves the cooling rate compared to conventional schemes with fixed laser frequency and power,and eliminates the need for mode-specific addressing.Our Floquet parallel scheme is applicable to any harmonic oscillator system and is not limited by bandwidth in theory.

Valence Bands Convergence in p-Type CoSb_(3) through Electronegative Fluorine Filling

Band convergence is considered to be a strategy with clear benefits for thermoelectric performance,generally favoring the co-optimization of conductivity and Seebeck coefficients,and the conventional means include elemental filling to regulate the band.However,the influence of the most electronegative fluorine on the CoSb_(3) band remains unclear.We carry out density-functional-theory calculations and show that the valence band maximum gradually shifts downward with the increase of fluorine filling,lastly the valence band maximum converges to the highly degenerated secondary valence bands in fluorine-filled skutterudites.

Observation of parabolic electron bands on superconductor LaRu_(2)As_(2)

Ru-based superconductor LaRu_(2)As_(2) has been discovered exhibiting the highest critical temperature of ~ 7.8 K among iron-free transition metal pnictides with the ThCr_(2)Si_(2)-type crystal structure. However, microscopic research on this novel superconducting material is still lacking. Here, we utilize scanning tunneling microscopy/spectroscopy to uncover the superconductivity and surface structure of LaRu_(2)As_(2). Two distinct terminating surfaces are identified on the cleaved crystals, namely, the As surface and the La surface. Atomic missing line defects are observed on the La surface. Both surfaces exhibit a superconducting gap of ~ 1.0 me V. By employing quasiparticle interference techniques, we observe standing wave patterns near the line defects on the La atomic plane. These patterns are attributed to quasiparticle scattering from two electron type parabolic bands.

Extracting Feature Bands for Damaged Rice Leaves by Planthoppers Using Multi-spectral Imaging Technology

[Objective] The aim of this study was to extract effective feature bands of damaged rice leaves by planthoppers to make identification and classification rapidly from great amounts of imaging spectral data. [Method] The experiment, using multi-spectral imaging system, acquired the multi-spectral images of damaged rice leaves from band 400 to 720 nm by interval of 5 nm. [Result] According to the principle of band index, it was calculated that the bands at 515, 510, 710, 555, 630, 535, 505, 530 and 595 nm were having high band index value with rich information and little correlation. Furthermore, the experiment used two classification methods and calcu-lated the classification accuracy higher than 90.00% for feature bands and ful bands of damaged rice leaves by planthoppers respectively. [Conclusion] It can be con-cluded that these bands can be considered as effective feature bands to identify damaged rice leaves by planthoppers quickly from a large scale of crops.

In situ Detection of Amide A Bands of Proteins in Water by Raman Ratio Spectrum

The amide A band of protein is sensitive to the hydrogen bands of amide groups of proteins. However, it is hard to distinguish the amide A band of aqueous protein in situ directly, since it overlaps with O-H stretching vibration of water. In this work, we presented a new analytical method of Raman ratio spectrum, which can extract the amide A band of proteins in water. To obtain the Raman ratio spectrum, the Raman spectrum of aqueous protein was divided by that of pure water. A mathematical simulation was employed to examine whether Raman ratio spectrum is effective. Two kinds of protein, lysozyme and （^-chymotrypsin were employed. The amide A bands of them in water were extracted from Raman ratio spectra. Additionally, the process of thermal denaturation of lysozyme was detected from Raman ratio spectrum. These results demonstrated the Raman ratio spectra could be employed to study the amide A modes of proteins in water.

Deformation, Phase Transformation and Recrystallization in the Shear Bands Induced by High-Strain Rate Loading in Titanium and Its Alloys

α-titanium and its alloys with a dual-phase structure （α＋β） were deformed dynamically under strain rate of about 10^4 s^-1. The formation and microstructural evolution of the localized shear bands were characterized by scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The results reveal that both the strain and strain rate should be considered simultaneously as the mechanical conditions for shear band formation, and twinning is an important mode of deformation. Both experimental and calculation show that the materials within the bands underwent a superhigh strain rate （9×10^5 S^-1） deformation, which is two magnitudes of that of average strain rate required for shear band formation; the dislocations in the bands can be constricted and developed into cell structures; the phase transformation from α to α2 within the bands was observed, and the transformation products （α2） had a certain crystallographic orientation relationship with their parent; the equiaxed grains with an average size of 10 μm in diameter observed within the bands are proposed to be the results of recrystallization.

Common Spectral Bands and Optimum Vegetation Indices for Monitoring Leaf Nitrogen Accumulation in Rice and Wheat

Real-time monitoring of nitrogen status in rice and wheat plant is of significant importance for nitrogen diagnosis, fertilization recommendation, and productivity prediction. With 11 field experiments involving different cultivars, nitrogen rates, and water regimes, time-course measurements were taken of canopy hyperspeetral reflectance between 350-2 500 nm and leaf nitrogen accumulation （LNA） in rice and wheat. A new spectral analysis method through the consideration of characteristics of canopy components and plant growth status varied with phenological growth stages was designed to explore the common central bands in rice and wheat. Comprehensive analyses were made on the quantitative relationships of LNA to soil adjusted vegetation index （SAVI） and ratio vegetation index （RVI） composed of any two bands between 350-2 500 nm in rice and wheat. The results showed that the ranges of indicative spectral reflectance were largely located in 770-913 and 729-742 nm in both rice and wheat. The optimum spectral vegetation index for estimating LNA was SAVI （R822, R738） during the early-mid period （from jointing to booting）, and it was RVI （Rs22, R73s） during the mid-late period （from heading to filling） with the common central bands of 822 and 738 nm in rice and wheat. Comparison of the present spectral vegetation indices with previously reported vegetation indices gave a satisfactory performance in estimating LNA. It is concluded that the spectral bands of 822 and 738 nm can be used as common reflectance indicators for monitoring leaf nitrogen accumulation in rice and wheat.

Discovering Crustal Deformation Bands by Processing Regional Gravity Field

Objectives： This article presents a new computational procedure to discover scratches buried in the earth＇s crust. We also validate this new interdisciplinary analysis method with regional gravity data located in a well-known Dabie orogenic zone for test. Methods： Based on the scratch analysis method evolved with mathematical morphology of surfaces, we present a procedure that extracts information of the crustal scratches from regional gravity data. Because the crustal scratches are positively and highly correlated to crustal deformation bands, it can be used for delineation of the crustal deformation belts. The scratches can be quantitatively characterized by calculation of the ridge coefficient function, whose high value traces delineate the deformation bands hidden in the regional gravity field. In addition, because the degree of crustal deformation is an important indicator of tectonic unit divisions, so the crust can be further divided according to the degree of crustal deformation into some tectonic units by using the ridge coefficient data, providing an objective base map for earth scientists to build tectonic models with quantitative evidence. Results： After the ridge coefficients are calculated, we can further enhance the boundary of high ridge-coefficient blocks, resulting in the so-called ridge-edge coefficient function. The high-value ridge-edge coefficients are well correlated with the edge faults of tectonic units underlay, providing accurate positioning of the base map for compilation of regional tectonic maps. In order to validate this new interdisciplinary analysis method, we select the Dabie orogenic zone as a pilot area for test, where rock outcrops are well exposed on the surface and detailed geological and geophysical surveys have been carried out. Tests show that the deformation bands and the tectonic units, which are conformed by tectonic scientists based on surface observations, are clearly displayed on the ridge and ridge-edge coefficient images obtained in this article. Moreover, these computer-generated images provide more accurate locations and geometric details. Conclusions： This work demonstrates that application of modern mathematical tools can promote the quantitative degree in research of modern geosciences, helping to open a door to develop a new branch of mathematical tectonics.

Dynamic Mechanical Behavior and Adiabatic Shear Bands of Ultrafine Grained Pure Zirconium

Dynamic compression tests were carried out to investigate dynamic mechanical behavior and adiabatic shear bands in ultrafine grained(UFG)pure zirconium prepared by equal channel angular pressing(ECAP)and rotary swaying.The cylindrical specimens were deformed dynamically on the split Hopkinson pressure bar(SHPB)at different strain rates of 800 to 4000s^-1 at room temperature.The temperature distribution of the shear bands was estimated on the basis of temperature rise of uniform plastic deformation stage and thermal diffusion effect.The results show that the true stress-true strain curves of UFG pure zirconium are concave upward trend of strain in range of 0.02-0.16 due to the effects of strain hardening,strain rate hardening and thermal softening.The formation of the adiabatic shear bands is the main reason of UFG pure zirconium failure.A large number of micro-voids are observed in the adiabatic shear bands,and the macroscopic cracks develop from the micro-voids coalescence.The fracture surface of UFG pure zirconium exhibits quasi cleavage fracture with the characteristic features of shear dimples and river pattern.The highest temperature within the shear bands of UFG pure zirconium is about 592 K.

The Analysis on the Candidate Frequency Bands of Future Mobile Communication Systems

Appropriate candidate frequency bands are extremely important for the development of future 5G systems. In this work, the researches on 5G spectrum around the world are summarized. Then the potential candidate frequency bands for 5G systems are investigated based on practical utilization of spectrum in China. For spectrum below 6GHz, the feasibility of possible frequency bands for 5G system are analyzed, which mainly come from 2G/3G/4G spectrum re-farming, the spectrum identified by footnotes for IMT systems in Regulations on the Radio Frequency Allocation of China, and potential candidate bands from WRC-15 Agenda Item 1.1. Moreover, propagation characteristics of WRC-15 candidate frequency bands proposed by China are measured and modeled to verify their effectiveness. For spectrum above 6GHz, the potential candidate frequency bands for 5G systems are selected based on the preliminary analysis of spectrum allocation, allotment and the current usage in China. Suggestions are provided for further studies on 5G spectrum.

Adiabatic Shear Bands in 30CrNi_3MoV Structural Steel Induced during High Speed Cutting

The width and spacing of adiabatic shear bands (ASBs) in the serrated chips generated during high speed orthogonal cutting of 30CrNi3MoV structurai steel were measured by opticai microscopy (OM), the temperature rise in the shear band was estimated. The microstructures of the ASBs were also characterized by SEM and TEM. The results show that the width and spacing of ASBs decrease with the increase of the cutting speed. The further observations show that the microstructure between the matrix and the center of the ASB gradually changes, and that the martensitic phase transformation, carbide precipitation and recrystallization may occur in the ASB.

Cognitive anti-jamming receiver under phase noise in high frequency bands

This paper investigates the jamming sensing performance of the simultaneous transmit and receive based cognitive anti-jamming(SCAJ) receiver impaired by phase noise in local oscillators(LO) over fading channels. Firstly, energy detection(ED)based on the jamming to noise ratio(JNR) of the high frequency bands SCAJ receiver with phase noise under different channels is analyzed. Then, the probabilities of jamming detection and false alarm in closed-form for the SCAJ receiver are derived. Finally,the modified Bayesian Cramer-Rao bound(BCRB) of jamming sensing for the SCAJ receiver is presented. Simulation results show that the performance degradation of the SCAJ system due to phase noise is more severe than that due to the channel fading in the circumstances where the signal bandwidth(BW) is kept a constant. Moreover, the signal BW has an effect on the phase noise in LO, and the jamming detection probability of the wideband SCAJ receiver with lower phase noise outperforms that of the narrowband receiver using the same center frequency. Furthermore,an accurate phase noise estimation and compensation scheme can improve the jamming detection capability of the SCAJ receiver in high frequency bands and approach to the upper bound.

Deformation measurements of three types of Portevin-Le Chatelier bands

In this paper a technique based on high-speed digital photography and the digital speckle correlation （DSC） method is used for the quantitative measurement of the displacement and strain fields of various Portevin Le Chatelier （PLC） bands （types A, B, and C）. The experimental results clearly show the nucleation process of a type-B band and the propagation of a type-A band. The results also reveal that there exists an elastic shrinkage deformation outside a PLC band during a large avalanche-like deformation inside the PLC band.

Rapid estimation of soil heavy metal nickel content based on optimized screening of near-infrared spectral bands

In near-infrared spectroscopy,the traditional feature band extraction method has certain limitations.Therefore,a band extraction method named the three-step extraction method was proposed.This method combines characteristic absorption bands and correlation coefficients to select characteristic bands corresponding to various spectral forms and then uses stepwise regression to eliminate meaningless variables.Partial least squares regression(PLSR)and extreme learning machine(ELM)models were used to verify the effect of the band extraction method.Results show that the differential transformation of the spectrum can effectively improve the correlation between the spectrum and nickel(Ni)content.Most correlation coefficients were above 0.7 and approximately 20%higher than those of other transformation methods.The model effect established by the feature variable selection method based on comprehensive spectral transformation is only slightly affected by the spectral transformation form.Infive types of spectral transformation,the RPD values of the proposed method were all within the same level.The RPD values of the PLSR model were concentrated between 1.6 and 1.8,and those of the ELM model were between 2.5 and2.9,indicating that this method is beneficial for extracting more complete spectral features.The combination of the three-step extraction method and ELM algorithm can effectively retain important bands associated with the Ni content of the soil.The model based on the spectral band selected by the three-step extraction method has better prediction ability than the other models.The ELM model of the first-order differential transformation has the best prediction accuracy(RP^2=0.923,RPD=3.634).The research results provide some technical support for monitoring heavy metal content spectrum in local soils.

POST- MICROBUCKLING OF FIBRE BRIDGING KINK BANDS UNDER COMPRESSION

Surface originated kink bands consist of an important failure mode for fibre-reinforced compo- sites under compression. The mechanical behavior of the fibre bridging kink bands is explored herein in the context of the post-microbuckling theory. Expressions of bridging force are obtained for the entire postbuckling process of the fibres exhibiting weak or strong hardening. The postbuckling formulation of the fibres is applied to yield the toughness increment due to the advancing kink bands, and consequently leads to a quantitative pre- diction on the overall compressive stress strain curves of the fibre-reinforced composites.

Exotic electronic states in the world of flat bands:From theory to material

It has long been noticed that special lattices contain single-electron flat bands （FB） without any dispersion. Since the kinetic energy of electrons is quenched in the FB, this highly degenerate energy level becomes an ideal platform to achieve strongly correlated electronic states, such as magnetism, superconductivity, and Wigner crystal. Recently, the FB has attracted increasing interest because of the possibility to go beyond the conventional symmetry-breaking phases towards topologically ordered phases, such as lattice versions of fractional quantum Hall states. This article reviews different aspects of FBs in a nutshell. Starting from the standard band theory, we aim to bridge the frontier of FBs with the textbook solid- state physics. Then, based on concrete examples, we show the common origin of FBs in terms of destructive interference, and discuss various many-body phases associated with such a singular band structure. In the end, we demonstrate real FBs in quantum frustrated materials and organometallic frameworks.

Characteristics and formation mechanisms of defect bands in vacuum-assisted high-pressure die casting AE44 alloy

The microstructure in vacuum-assisted high-pressure die casting(HPDC) Mg-4Al-4RE(AE44) alloy was studied. Special attention was paid to the characteristics of defect bands and their formation mechanisms. Since double defect bands are commonly observed, the cross section of die cast samples is divided into five parts with different grain morphologies and size distributions. The inner defect band is much wider than the outer one. Both the defect bands are solute segregation bands, resulting in a higher area fraction of Al;RE;phase than that in the adjacent regions. No obvious aggregation of porosities is observed in the defect bands of AE44 alloy. This may be due to a narrow solidification temperature range of AE44 alloy and a large amount of latent heat released during the precipitation of intermetallic phases. The formation of the defect bands is related to the shear stress acting upon the partially solidified alloy, which can lead to collapse of the grain network. However, the generation mechanisms of shear stress in the outer and inner defect bands are quite different.

Microstructural Characterization of the Shear Bands in Fe-Cr-Ni Single Crystal by EBSD

An investigation has been made into the microstructural characterization of the shear bands generated under high-strain rate （≈10^4 s^-1） deformation in Fe-15%Cr-15%Ni single crystal by EBSD-SEM （electron backscatter diffraction-scanning electron microscopy）, TEM （transmission electron in microscopy） and HREM （high- resolution electron microscopy）. The results reveal that the propagation of the shear band exhibits an asymmetrical behavior arising from inhomogenous distribution in plasticity in the bands because of different resistance to the collapse in different crystallographic directions; The γ-ε-α′phase transformations may take place inside and outside the bands, and these martensitic phases currently nucleate at intersections either between the twins and deformation bands or between the twins and ε-sheet. Investigation by EBSD shows that recrystallization can occur in the bands with a grain size of an average of 0.2μm in diameter. These nano-grains are proposed to attribute to the results of either dynamic or static recrystallization, which can be described by the rotational recrystallization mechanism. Calculation and analysis indicate that the strain rate inside the shear band can reach 2.50×10^6 s^-1, which is higher, by two or three orders of magnitude, than that exerted dynamically on the specimen tested.

MCR-BANDS用于高光谱成像分辨中旋转模糊度的评估

自建模曲线分辨用来将双线性光谱数据矩阵分解成具有明确物理或化学意义的曲线,一方面反映了复杂体系中各个主成分对应的纯光谱,同时也能够解析得到其对应的相对浓度。这一方法在高光谱解析中充分发挥了其优势,成为了高光谱分析中的重要方法之一。然而,双线性结构数据多元分辨模型在约束不充分的条件下往往不能获得唯一解,这一问题是由顺序模糊、尺度模糊和旋转模糊引起,其中旋转模糊最难消除。在高光谱成像中,如果不能明确浓度分布情况,将导致在成像领域难以确认目标的准确位置或形貌。为了充分了解旋转模糊带来的影响,评估非唯一解情况下可行解的范围,并进一步为实际应用中需要解析获得的每个主成分的纯光谱或波谱信号,以及其对应的浓度信息提供客观的评估依据,在以往的研究中,研究人员分别使用网格法、蒙特卡洛法进行抽样,以计算曲线分辨结果中可行解的范围,也有科研人员使用了几何多边形内部和外围面积的形式表示结果,但是这些结果往往面临运算时间过长,或者无法实现高维可视化而不适用于大于四个主成分的数据等问题,而且通常这些方法很难将曲线分辨过程中施加的除非负约束之外的其他约束方法加以利用,导致可行解范围计算不准确。为了解决以上问题,采用MCR-BANDS对MCR-ALS(多元曲线分辨-交替最小二乘)分辨获得的结果进行了旋转模糊程度的评估,并将其应用到遥感高光谱成像的解析中。首先以美国地质勘探局矿物光谱库中的纯光谱为基础的模拟数据集对MCR-ALS和MCR-BANDS的结果进行了评测,在模拟数据中能够方便地控制噪声的影响,控制选取主成分之间的纯光谱差异、仿照真实环境中浓度渐变特征等因素,考查了特定条件下MCR结果中旋转模糊的水平。随后为了证实所用方法的可行性,进一步采用MCR-ALS分析了机载可见/红外成像光谱仪(AVIRIS)获得的遥感高光谱图像数据,并首次采用MCR-BANDS对MCR-ALS的分辨结果的旋转模糊进行了分析,实现了对遥感高光谱数据成像浓度分布的受到旋转模糊影响的可视化表示。可以发现真实解和MCR-ALS获得的可行解均在MCR-BANDS计算得到的可行解范围之内。结果表明, MCR-BANDS方法基于最大和最小的信号贡献对旋转模糊的范围进行计算,能够适用于不同主成分的体系中,并且完美对接MCR-ALS中使用到的诸如非负、单峰、封闭和选择性约束等。MCR-BANDS的分析结果可以为MCR-ALS的解析结果提供相应的旋转模糊水平估计,有利于对MCR-ALS结果的解释;在充分约束条件下,能够有效减少甚至消除旋转模糊对MCR-ALS分辨结果的影响,为精确确定遥感高光谱中解析得到的目标物位置提供了客观的范围。