The microscopic mechanical performance for nonuniform welded joint of nickel-based alloy with nanoindentation

To quantify the nonuniform micromechanical performance of welded joint,the load-displacement curves by nanoindentation test were introduced to examine different zones including base metal,coarse grained heat affected zone,partially melted zone,weld metal near the fusion boundary and weld metal center.The results showed that the strengthening effect of weld metal was more obvious than that of heat affected zone for nickel based welded joint and especially in coarse grained heat affected zone,the hardening resulted from overheating was not apparent.Nickel based weld metal with high content of alloying elements which were often segregated at interdendritic regions or precipitated in grain interior under nonequilibrium solidification contributed to the characteristics that differ from conventional low alloy steel welded joint.

Urinary levels of nickel and chromium associated with dental restoration by nickel-chromium based alloys

This paper aims to investigate if the dental restoration of nickel-chromium based alloy(Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine.Seven hundred and ninety-five patients in a dental hospital had single or multiple Ni-Cr alloy restoration recently and 198 controls were recruited to collect information on dental restoration by questionnaire and clinical examination.Urinary concentrations of Ni and Cr from each subject were measure by graphite furnace atomic absorption spectrometry.Compared to the control group,the urinary level of Ni was significantly higher in the patient group of < 1 month of the restoration duration,among which higher Ni excretions were found in those with either a higher number of teeth replaced by dental alloys or a higher index of metal crown not covered with the porcelain.Urinary levels of Cr were significantly higher in the three patient groups of <1,1 to <3 and 3 to <6 months,especially in those with a higher metal crown exposure index.Linear curve estimations showed better relationships between urinary Ni and Cr in patients within 6-month groups.Our data suggested significant increased excretions of urinary Ni and Cr after dental restoration.Potential short- and long-term effects of Ni-Cr alloy restoration need to be investigated.

Effect of heat treatment on microstructure and high temperature tensile properties of cast nickel-base superalloy with high W, Mo and Nb contents

The microstructural features and high temperature tensile properties of M963 superalloy at as cast, as solutioned and as aged conditions were investigated in detail. The results show that the solution treatment at 1?220?℃ for 4?h, AC causes an increase in high temperature yield strength but a drastic drop in high temperature ductility due to the precipitation of both the secondary carbide M 6C along grain boundaries and at the interdendritic regions and very fine γ ′ particles in the dendrite cores. Aging treatment following the solution treatment can improve the high temperature tensile properties of M963 superalloy due to the coarsing of the γ′ precipitate. One stage aging at 850?℃ for 16?h following the solution treatment causes an increase in both strength and ductility of alloy M963, and two stage aging of 1?089?℃ / 2?h, AC plus 850?℃ / 16?h, AC following the solution treatment further increases the ductility of alloy M963 but slightly decreases its strength.

Research on CMT welding of nickel-based alloy with stainless steel

Cold Metal Transfer （CMT） welding technique is a new welding technique introduced by Fronins company. CMT welding of nickel-based alloy with stainless steel was carried out using CuSi3 filler wire in this paper. Effects of welding parameters, including welding current, welding speed, etc, on weld surface appearance were tested. Microstructure and mechanical properties of CMT weld were studied. The results shaw that the thickness of interface reaction layer of the nickel- based alloy is 14. 3 μm, which is only 4. 33% of base material. The weld is made up of two phases, α-copper and iron-based solid solution. Rupture occurs initially at the welded seam near the edge of stainless steel in shear test. The maximum shear strength of the CuSi3 welded joint is 184. 9 MPa.

Effect of electroless plating nickel treatment on electrode properties of Zr-based AB_2 type alloy

An electroless plating nickel treatment was processed to improve the active behaviors and discharge capacities of Zr based AB 2 alloys. The effects of the nickel coating on the surface appearance, the structure of the alloy powders and the electrode characteristics were investigated. It is found that the Ni rich layer formed through electroless plating nickel treatment plays an important role on the initial activation property and the discharge capacity of Zr based alloy. The optimal content of electroless plating nickel is about 15%, and the discharge capacity of the electrode can be increased to 400?mA·h·g -1 after 6 cycles. Although coated nickel is beneficial for quick activation and discharge capacity, excessive electroless plating nickel can result in a decreased discharge capacity.

Inner and outer pressure forming of nickel based super-alloy thin-walled part with variable diameter sections

A novel forming method of nickel based super-alloy thin-walled part with variable diameter sections was proposed by using inner and outer pressure with the visco-elasto-plastic pressure-carrying medium at room temperature,and the principle of the method was provided.Experiments and FE simulations were carried out to analyze the deformation characteristics for the part with larger variable diameter ratio(35%).The results show that visco-elasto-plastic pressure-carrying medium can meet the requirements of the room-temperature deformation condition for nickel based super-alloy sheet.The inner and outer pressure forming with the visco-elasto-plastic pressure-carrying medium can meet the requirements of dimensional accuracy for the thin-walled part with variable diameter sections.The thinning of wall-thickness is less than 4%.This method provides a new approach for near-net shape forming of nickel based super-alloy thin-walled parts with variable diameter sections.

Simulation and experiments of ultrasonic propagation in nickel-based alloy weldments

In order to obtain good understanding of complicated beam propagation behaviors in nickel-based alloy weldments , ray tracing simulation is established to predict the ultrasonic beam path in a special welded structure of dissimilar steels. Also experimental examinations are carried out to measure the ultrasonic beam paths in the weldment. Then comparisons of the modeling predictions with experimental results are presented to reveal the complicated beam propagation behaviors.

Electronic Properties of Passive Films Formed on G3 and G30 Nickel-based Alloys in Bicarbonate/Carbonate Buffer Solution

The electronic properties of passive films formed on G3 and G30 alloys in bicarbonate/carbonate buffer solution were comparatively studied by electrochemical impedance spectra（EIS） and Mott-Schottky analysis, the chemical composition of the passive film formed on G3 alloy was detected by X-ray photoelectron spectroscopy （XPS）. The results show that passive film on G3 alloy had better protection than that on G30 alloy. The transfer resistance, film resistance and diffusion resistance of the passive films on both alloys increased with increasing formation potential, prolonging formation time, increasing pH value, decreasing formation temperature, and decreasing chloride and sulphide ions concentration. Mott-Schottky plot reveals that the passive films on the two alloys show a p-n semi-conductive character. XPS analysis indicates that the passive film on G3 alloy was composed of an inner Cr oxide and an outer Fe, Mo/Ni oxides.

THE ROLE OF NIOBIUM IN NICKEL-BASED SUPERALLOYS AND CHARACTERIZATION OF PM ALLOY EP741NP

The role of niobium in nickel-based superalloys is reviewed. The importance of niobium as a strengthener is discussed. New developments in nickel-based superalloys are also briefly mentioned, including some results that show improved resistance to sulfidation by niobium. Research results from a current program on the role of niobium in the Russian powder metallurgy alloy EP741NP are presented. Future research plans on the role of niobium in superalloys are also discussed.

ADVANCED NICKEL-BASED AND NICKEL-IRON-BASED SUPERALLOYS FOR CIVIL ENGINEERING APPLICATIONS

The use of high-temperature materials is especially important in power station construction, heating systems engineering, furnace industry, chemical and petrochemical industry, waste incineration plants, coal gasification plants and for flying gas turbines in civil and military aircrafts and helicopters. Particularly in recent years, the development of new processes and the drive to improve the economics of existing processes have increased the requirements significantly so that it is necessary to change from well-proven materials to new alloys. Hitherto, heat resistant ferritic steels sufficed in conventional power station constructions for temperatures up to 550℃ newly developed ferritic/martensitic steels provide sufficient strength up to about 600 - 620℃. In new processes, e.g. fluidized-bed combustion of coal, process temperatures up to 900℃ occur. However, this is not the upper limit, since in combustion engines, e.g. gas turbines. Material temperatures up to 1100℃ are reached locally. Similar development trends can also be identified in the petrochemical industry and in the heat treatment and furnace engineering. The advance to ever higher material temperatures now not only has the consequence of having to use materials with enhanced high-strength properties, considerable attention now also has to be given to their chemical stability in corrosive media. Therefore not only examples of the use of high-temperature alloys for practical applications will be given but also be contributed to some general rules for material selection with regard to their high-temperature strength and corrosion resistance.

Effect of electropulsing treatment on corrosion behavior of nickel base corrosion-resistant alloy

Electropulsing treatment（EPT） was performed on a nickel base corrosion resistant alloy during aging.The effect of EPT on the microstructure and corrosion resistance of the alloy and the mechanisms were investigated.The results show that the intergranular corrosion resistance can be improved substantially without the degradation of mechanical properties of the alloy by EPT.The EPT has an effect of enhancing the interface diffusion rate of the alloying element,which is higher than the body diffusion rate.And thus discontinuous precipitation of M23C6 type carbides appears at the grain boundary in the alloy by EPT,which decreases the depletion extent of the alloying elements at the grain boundary substantially.As a result,the intergranular corrosion resistance of the alloy can be improved by the EPT without any degradation of mechanical properties.

Corrosion performance and applicability evaluation of nickel-based alloys for oil and gas production tubing applications

The sulfide stress corrosion cracking（ SSC） performance of G3 and 028 nickel-based alloys w as studied using slow strain rate test（ SSRT） and the four-point bend（ FPB） test under simulated dow nhole conditions. The effect of high temperature,high H2 S / CO2 partial pressure,and the presence of sulfur on SSC susceptibility w as investigated. The G3 alloy w as found to have a higher SSC resistance than the 028 alloy. Presence of sulfur and temperature bear a strong influence on the SSC performance of the metals,particularly on the 028 alloy. The applicability of 028 and G3 alloys may be expanded and both could safely be used beyond the limits set by the ISO15156-3 standard.

Liquid-solid interface control of BFe10-1-1 cupronickel alloy tubes during HCCM horizontal continuous casting and its effect on the microstructure and properties

Based on horizontal continuous casting with a heating-cooling combined mold （HCCM） technology, this article investigated the effects of processing parameters on the liquid-solid interface （LSI） position and the influence of LSI position on the surface quality, microstructure, texture, and mechanical properties of a BFe10-1-1 tube （φ50 mm × 5 mm）. HCCM efficiently improves the temperature gradient in front of the LSI. Through controlling the LSI position, the radial columnar-grained microstructure that is commonly generated by cooling mold casting can be eliminated, and the axial columnar-grained microstructure can be obtained. Under the condition of 1250℃ melting and holding temperature, 1200-1250℃ mold heating temperature, 50-80 mm/min mean drawing speed, and 500-700 L/h cooling water flow rate, the LSI position is located at the middle of the transition zone or near the entrance of the cooling section, and the as-cast tube not only has a strong axial columnar-grained microstructure （{hkl}〈621〉, {hkl}〈221〉） due to strong axial heating conduction during solidification but also has smooth internal and external surfaces without cracks, scratches, and other macroscopic defects due to short solidified shell length and short contact length between the tube and the mold at high temperature. The elongation and tensile strength of the tube are 46.0%-47.2% and 210-221 MPa, respectively, which can be directly used for the subsequent cold-large-strain processing.

Effect of additives on anode passivation in direct electrolysis process of copper–nickel based alloy scraps

Effects of nickel component,thiourea,glue and chloride ions and their interactions on the passivation of copper–nickel based alloy scrap anodes were investigated by combining conventional electrochemical techniques.Results obtained from chronopotentiometry and linear voltammetry curves showed that the Ni component made electrochemical stability of the anode strong and difficult to be corroded,caused by the adsorption of generated Cu2O,NiO or copper powder to the anode surface.The Ni2+reducing Cu2+to Cu+or copper powder aggravated the anode passivation.In a certain range of the glue concentration≤8×10–6 or thiourea concentration≤4×10–6,the increase of glue or thiourea concentration increases the anode passivation time.Over this range,glue and thiourea played an adverse effect.The increase of chloride ions concentration led to the increase in passivation time.

XPS analysis of passive film formed on the G3 nickel-base alloy tubing under corrosive conditions

In the present study, the passive film formed on the G3 nickel-base alloy tubing under corrosive conditions including H2S ,CO2 ,and Cl-at 130 ℃ and 205 ℃ is studied with X-ray photoelectron spectroscopy（XPS）. The results reveal that the passive film formed at 205℃ consists of Cr, Ni, Fe, S and O elements and is over 470 nm in thickness. The passive film can be divided into three layers, the outer-layer is composed of NiS2 and Cr2 S3 , the intermediate-layer of Cr（OH） 3, Ni （OH） 2, NiS2, Cr2 $3 and a small quantity of NiO and Cr2 O3, and the inner-layer of NiO, Cr2 O3, and alloy elements. Due to the invasion of S2 - into the passive film and the decrease of the content of chromium oxide in the film, the corrosion resistance of the G3 alloy in the sour environment at 205 ℃ is weakened.

Nickel-base superalloys for USC power plants

The advanced ultra-supercritical power plants of the future will utilize steam pressures and temperatures that are too high for traditional ferritic steels,thus requiring austenitic materials.Older nickel-base superalloys such as 263 and 617 were initially evaluated under the European THERMIE project beginning in the 1990s.An entirely new age-hardened alloy 740 which possesses exceptional fireside corrosion resistance and creep strength was also developed for boiler tubing capable of serving at 700C.Subsequently,interest in the USA considered other product forms such as steam header piping and steam turbine forgings for service as high as 760C.A more stable and weldable alloy version now called 740H was developed to meet these more demanding conditions.This paper summarizes the current status of work on alloys 740 and 740H.

NICKEL-BASE ALLOY SHEET ALLOYS USED IN AEROSPACE APPLICATIONS

Many gas turbine components are made from nickel alloy sheet. Most are used for directing or containing gases at high temperatures and pressures where metal temperatures can be as high as 1090℃ (2000°F). These applications included combustor systems, casings and liners, transition and exhaust ducting, afterburners, and thrust reversere. Light weight components and sub-assemblies call for alloy sheet with high levels of stength and oxidation resistance. Complex component design calls for excellent ductility and ease of fabrication.The wide range of nickel alloy sheet alloys presently used in aircraft and land-based gas turbines is briefly described and typical properties presented. New sheet alloy developments, involving INCONEL￣* alloys 625LCF, 718SPF and MA754, are presented including the process routes involved and material properties.

GRAIN STRUCTURE CONTROL OF NICKEL－BASE SUPERALLOYS IN CASTING PROCESS：EFFECT OF FOUNDRY VARIABLES

ＧＲＡＩＮＳＴＲＵＣＴＵＲＥＣＯＮＴＲＯＬＯＦＮＩＣＫＥＬ－ＢＡＳＥＳＵＰＥＲＡＬＬＯＹＳＩＮＣＡＳＴＩＮＧＰＲＯＣＥＳＳ：ＥＦＦＥＣＴＯＦＦＯＵＮＤＲＹＶＡＲＩＡＢＬＥＳＧＲＡＩＮＳＴＲＵＣＴＵＲＥＣＯＮＴＲＯＬＯＦＮＩＣＫＥＬ－ＢＡＳＥＳＵＰＥＲ...

Structural Characterization of Nickel-Base Alloy C-276 Irradiated with Ar Ions

The irradiation damage in nickel-base alloy C-276 irradiated with 115 keV Ar ions from low to very high doses was investigated. Structural characterization was performed using transmission electron microscopy （TEM）, grazing incident X-ray diffraction （GIXRD） and atomic force microscopy （AFM）. High density of interstitial type dislocation loops could be observed at a dose level of around 2.75 displacements per atom （dpa）. With the irradiation dose increased to 27.5 dpa, the average size of loops increased from 5 nm to 16 nm, while the density of the loops decreased from 1.4 × 1011/cm2 to 4.6 × 1010/cm2. When the irradiation dose reached 82.5 dpa, original grains were transformed into subgrains whose sizes observed from TEM were about 20-60 nm. The fragmentation of grains was confirmed by GIXRD. The mean subgrain size was 40 nm, which was obtained from the full width at half maximum （FWHM） of the X-ray diffraction lines using the Scherrer formula and Williamson formula. AFM micrographs showed that nanometer-sized hillocks formed at the dose of 82.5 dpa, which provided further evidence of grain fragmentation at a high irradiation dose.