Stress Measurement with an Improved Hollow Inclusion Technique In Jinchuan Nickel Mine

Borehole overcoring stress measurement with an improved hollow inclusion technique was carried out at 10 points on 3 levels in Jinchuan nickel mine which is situated in north-west of China. Through the measurement, 3-D in situ stress state at the measuring points and distribution characteristics of the stress field in the mine were obtained. The stress state in Jinchuan mine is dominated by the horizontal tectonic stress field. The maximum principal stress is horizontal which is about twice the weight of the overburden and its orientation is approximately vertical to the regional tectonic line. The difference between two horizontal principal stresses is quite large which is an important reason to cause failure of underground excavations.

Feasibility Study on Continuous Mining Method in Deep Position of Jinchuan Nickel Mine, China

Jinchuan nickel mine is the largest nickel mine in China. Cut-and-fill mining method with high density cementing materials is used in the mine. The original mining design divided the mining operation into two steps. The first step stopped the mining rooms and the second step stopped the pillars. Because the two-step method made big trouble for finally mining pillars and strongly limited the mining speed and production, it was successfully changed to a continuous cut-and-fill method without pillars. However, the mining operation in the mine has been down to 800 m and the mining condition is getting worse and more complicated. Through systematical field investigations and 3-D FEM analysis, it is proved that the mining method without pillars is feasible for mining deeper orebodies in Jinchuan nickel mine.

Mineralogy and crystal chemistry of a low grade nickel laterite ore

To acquire understanding of Ni enrichment from laterite ore,the mineralogy and crystal chemistry of a low grade limonite type nickel laterite ore sample assaying 0.97% Ni from Indonesia were studied using optical microscopy,X-ray diffraction（XRD）,scanning electron microscopy（SEM） and electron probe microanalysis（EPMA）.According to EPMA results,the mineral includes 80% goethite（（Fe,Ni,Al）O（OH）） with 0.87% Ni,15% silicate minerals with lizardite（（Mg,Fe,Ni）3Si2O5（OH）） and olivine（（Mg,Fe,Ni）2SiO4）,and 1.19% Ni,and other minor phases,such as hematite,maghemite,chromite and quartz,and no Ni was detected.The mineralogy of the laterite ore indicates that due to the complicated association of the various phases and the variable distribution of Ni,this refractory laterite ore can not be upgraded by traditional physical beneficiation processes.

Kinetics and equilibrium adsorption of copper(Ⅱ) and nickel(Ⅱ) ions from aqueous solution using sawdust xanthate modified with ethanediamine

Sawdust xanthate modified with ethanediamine was used for the removal of Cu（Ⅱ） and Ni（Ⅱ） from aqueous solution. The influence of various operating parameters such temperature and adsorbent dosage on the adsorption isotherms of modified sawdust was investigated. Thermodynamic parameters, namely Gibbs free energy （△GΘ）, enthalpy （△HΘ） and entropy （△SΘ） of Cu（Ⅱ） and Ni（Ⅱ） adsorption process were calculated, showing that the adsorption is a spontaneous and exothermic process. The modified extended Langmuir equation approaches provide excellent prediction of the binary adsorption. In single and binary systems, the overall adsorption data were best described by the pseudo-second order kinetic model, then the calculated values of activation energy of Cu（Ⅱ） and Ni（Ⅱ） adsorption process were 59.12 and 55.92 kJ/mol respectively. The results show that the affinity of each metal ion onto the modified sawdust surface is influenced by the presence of the other one.

Effects of the Supports on Activity of Supported Nickel Catalysts for Hydrogenation of m-Dinitrobenzene to m-Phenylenediamine

The hydrogenation of m-dinitrobenzene to m-phenylenediamine in liquid phase was studied with the nickel catalysts supported on SiO2, TiO2, γ-Al2O3, MgO and diatomite carders. Based on the experiments of X-ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, temperature-programmed reduction （TPR）, temperature-programmed desorption of hydrogen （H2-TPD） and activity evaluation, the physico-chemical and catalytic properties of the catalysts were investigated. Among the catalysts tested, the SiO2 supported nickel catalyst showed the highest activity and selectivity towards m-phenylenediamine, over which 97.3% m-dinitrobenzene conversion and 95.1% m-phenylenediamine yield were obtained at 373K under hydrogen pressure of 2.6MPa after reaction for 6 h when using ethanol as solvent. Although TiO2 and diatomite supported nickel catalysts also presented high activity, they had lower selectivity towards m-phenylenediamine. As for γ-Al2O3 and MgO supported catalysts were almost inactive for the object reaction. It was shown that both the activity and selectivity of the catalysts were strongly depended on the interaction between nickel and the support. The higher activities of Ni/SiO2, Ni/TiO2 and Ni/diatomite could be attributed to the weaker metal-support interaction, on which Ni species presented as crystallized Ni metal particles. On the other hand, there existed strong metal-support interaction in Ni/MgO and Ni γ-Al2O3, which causes these catalysts more difficult to be reduced and the availability of Ni active sites decreased, resulting in their low catalytic activity.

Relationship between process mineralogical characterization and beneficiability of low-grade laterite nickel ore

Process mineralogy of low-grade laterite nickel ore in Indonesia was systematically characterized and the beneficiation process of mineral components such as limonite,serpentine and chromite was studied on the basis of process mineralogy.The results show that the low-grade laterite nickel ore is a typical weathering sedimentary metamorphic oxidized ore,with the main valuable elements of Ni,Co and Cr and the main mineral components of limonite,serpentine,chromite,etc.There is no independent carrier mineral of Ni and Co in the raw ore,and the occurrence states of Ni and Co are relatively dispersed.For the limonite in laterite nickel mine,the nickel bearing magnetite concentrate with nickel grade of 1.98%and recovery rate of 88.42%can be obtained by reduction roasting magnetic separation process.For the serpentine in laterite nickel mine,the cobalt bearing concentrate with Co grade of 0.17%and recovery rate of 23.17%can be obtained by positive and reverse flotation process.A chromium concentrate containing 35.17%Cr_(2)O_(3) and a recovery of 33.42%can be obtained by using the combined process of coarse and fine classification and gravity and magnetic.

Generation process of FeS and its inhibition mechanism on iron mineral reduction in selective direct reduction of laterite nickel ore

Numerous studies have demonstrated that Na2SO4 can significantly inhibit the reduction of iron oxide in the selective reduction process of laterite nickel ore. FeS generated in the process plays an important role in selective reduction, but the generation process of FeS and its inhibition mechanism on iron reduction are not clear. To figure this out, X-ray diffraction and scanning electron microscopy analyses were conducted to study the roasted ore. The results show that when Na2SO4 is added in the roasting, the FeO content in the roasted ore increases accompanied by the emergence of FeS phase. Further analysis indicates that NaeS formed by the reaction of Na2SO4 with CO reacts with SiO2 at the FeO surface to generate FeS and Na2Si2Os. As a result, a thin film forms on the surface of FeO, hindering the contact between reducing gas and FeO. Therefore, the reduction of iron is depressed, and the FeO content in the roasted ore increases.

Nickel solvent extraction from cold purification filter cakes of Angouran mine concentrate using LIX984N

Cold purification filter cakes generated in the hydrometallurgical processing of Angouran mine zinc concentrate commonly contain significant amounts of Zn, Cd, and Ni ions and thus are valuable resources for metal recovery. In this research, a nickel containing solution that was obtained from sulfuric acid leaching of the filter cake following cadmium and zinc removal was subjected to solvent extraction experiments using 10vol%LIX984N diluted in kerosene. Under optimum experimental conditions （pH 5.3, volume ratio of organic/aqueous （O：A） = 2：1, and contact time -5 min）, more than 97.1% of nickel was extracted. Nickel was stripped from the loaded organic by contacting with a 200 g/L sulfuric acid solution, from which 77.7% of nickel was recovered in a single contact at the optimum conditions （pH 1-1.5, O：A =5：1, and contact time =15 min）.

Ethylene Polymerization with Palygorskite Supported Nickel-Diimine Catalyst

A nickel-diimine catalyst [N, N'-bis(2,6-diisopropylphenyl)-1,4-diaza-2,3-dimethyl-1, 3-butadiene nickel dibromide, DMN] was supported on palygorskite clay for ethylene slurry polymerization. The effect of supporting methods on the catalyst impregnation was studied and compared. Pretreatment of the support with methylalumi-noxane (MAO) followed by DMN impregnation gave higher catalyst loading and catalytic activity than the direct impregnation of DMN. Catalyst activity as high as 5.42×105g PE·molNi-1·h-1 was achieved at ethylene pressure of 6.87×105 Pa and polymerization temperature of 20℃. In particular, the morphological change of the support during MAO treatment was characterized and analyzed. It was found that nano-fiber clusters formed during the support pretreatment, which increased the surface area of the support and favored the impregnation of the catalyst. The investigation of polymerization behavior of supported catalyst revealed that the polymerization rate could be kept at a relatively high level for a long time, different from the homogeneous catalyst. By analyzing the SEM photographs of the polymer produced by the supported catalyst, the morphological evolution of polymer particles was preliminarily studied.

Process Mineralogy of Lateritic Nickel Ore

This paper presents a methodology for studying low grade lateritic nickel ore, which usually presents complex mineralogy, with widespread nickel in several mineral phases. The study is focused on determining the mineralogy and the distribution of nickel in the bearing minerals. Laboratory assays comprise homogenization, sampling and particle size analysis. Chemical analyses by X-ray fluorescence are performed in all fractions sizes, while mineralogical assessments by X-ray diffraction are carried out for head sample. The mineralogical composition of the samples and the partition of main elements in the bearing minerals are assayed by size fraction through automated image analysis software (MLA) coupled to a scanning electron microscope (SEM). The chemical compositions of the several minerals identified in MLA are determined during systematic observations on SEM with energy dispersive spectrometer (EDS).

CYTOTOXICITY AND GENOTOXICITY OF POLYETHYLENIMINE AND NICKEL CHLORIDE IN RED SEA BREAM (Pagrosomus major) FIN CELL LINE RSBF

A continuous marine fish cell line RSBF (i.e. Red Sea Bream Fin) was utilized to screen the cytotoxicity and genotoxicity of polyethylenimine (PEI) and nickel chloride (NiCl 2) in this study on the deleterious effects of aquatic genotoxins on fish. At the 0.01 to 1 μg/ml concentration tested, PEI had acute toxicity to the treated RSBF cells (IC 50 =1.12, 0.92, 0.88 and 0.64 μg/ml PEI for time 0 h, 24 h, 48 h and 72 h after treatment, respectively) and markedly inhibited their proliferation in a dose dependent manner. At the 0.001 to 5 μmol/L concentration tested, NiCl 2 posed no acute toxicity but significantly stimulated their growth (107%-214% of control). Random amplified polymorphic DNA (RAPD) technique was used to detect the genotoxic effects of PEI and NiCl 2 by comparing the RAPD banding patterns of the control and treated cells. RAPD analysis indicated that at the concentrations tested, PEI was more genotoxic than NiCl 2 to RSBF cells; that there was a slight dose dependent response in the genotoxic effect of PEI but not NiCl 2; and that RAPD technique might provide a sensitive, non specific genotoxic endpoint. And the potent cytotoxicity and genotoxicity of PEI on fish cells showed that we should be cautious in utilizing it as gene vector in fish gene transfer and human gene therapy.

Highly Active New α-Diimine Nickel Catalyst for Polymerization of Ethylene

A new α-diimine ligand 1a, bis[N,N′-（4-tert-butyl-2,6-dimethylphenyl）imino]-2,3-butanediylidene and its corresponding Ni（II） complex 2a, {bis[N,N′-（4-tert-butyl-2,6-dimethylphenyl）imino]-2,3-butanediylidene}dibromo- nickel were successfully synthesized, and characterized by 1H NMR, 13C NMR, Fourier transform infrared spectroscope（FTIR）, elemental analysis and X-ray photoelectron spectroscopy（XPS）. α-Diimine ligand 1b, bis[N,N′-（2,6- dimethylphenyl）imino]-2,3-butanediylidene and its corresponding Ni（II） complex 2b, {bis[N,N′-（2,6-dimethyl- phenyl）imino]-2,3-butanediylidene}dibromonickel were also synthesized and characterized for comparison. The pre-catalyst 2a with sterically bulky, electron-donating group tert-butyl, activated by diethylaluminum chloride （DEAC） and tested in the polymerization of ethylene, was very highly active[2.01×107 g PE/（mol Ni？h？0.1 MPa）] and led to a very highly branched polyethylene（ca. 35―103 branches/1000 C）. The state of the polyethylene obtained varied from plastic, elastomer polymers to the oil-like hyperbranched polymers.

Synthesis,Structure and Norbornene Polymerization Catalyzed by Bis{(2-benzhydryl-4,6-dimethyl-phenyl)-(3,5-di-tert-butyl-2-methyl-benzylidene)-amine-N,O}nickel(Ⅱ)

The title complex bis{（2-benzhydryl-4,6-dimethyl-phenyl）-（3,5-di-tert-butyl-2-methyl-benzylidene）-amine-N,O}nickel has been synthesized by the reaction of（2-benzhydryl-4,6-dimethyl-phenyl）-（3,5-di-tert-butyl-2-methyl-benzylidene）-amine with Ni（CH3COO）2·4H2O, and characterized by IR spectrum and single-crystal X-ray diffraction analysis. The crystal belongs to the monoclinic system, space group P21/c with a = 12.373（4）, b = 18.434（7）, c = 27.814（10） A, β = 92.291（6）o, V = 6339（4） A^3, C7 2H8 0N2 Ni O2, Mr = 1064.09, Z = 4, Dc = 1.115 g/cm^3, μ = 0.350 mm^-1, F（000） = 2280, the final R = 0.0846 and wR = 0.2926（I 〉 2s（I））. This title compound was used as homogeneous catalysis of polymerization of norbornene, and the complex exhibited good catalytic activity to catalyze norbornene polymerization using MAO as a cocatalyst.

2022 Annual Report of China Mineral Resources(lithium,nickel,cobalt,REE etc.)

In September 2022,the Ministry of Natural Resources of PRC released the 2022 China Mineral Resources Report,which focuses on such information since 2021 as the new progress made in China’s geological survey;reconnaissance,exploration and development of mineral resources,mine ecological rehabilitation and green mine construction;new changes in policies and regulations related to mineral resources;new measures taken in management of mineral resources;new scientific and technological innovation;and new achievements obtained in the international cooperation on geological and mineral resources with countries participating in the“Belt and Road Initiative”.

Crystal Structure and Characterization of 2-N-(2-Hydroxy-benzylidene) Furanmethanoamine Nickel(II) Complex

The Ni（Ⅱ） complex with ligand 2-N-（2-hydroxy-benzylidene） furanmethanoamine has been synthesized and characterized by elemental analysis, IR and single-crystal X-ray diffraction. It crystallizes in the monoclinic system, space group C2/c with a = 2.0280（4）, b =0.57700（12）, c = 1.7340（4） nm, β = 94.74（3）°, Z = 4, Dc = 1.508 g/cm^3, the final R = 0.0434 and wR = 0.1112 for 1843 observed reflections with 1 〉 2σ（I）. X-ray analysis revealed that the Ni（Ⅱ） ion is coordinated by two nitrogen atoms of Schiff base and two oxygen atoms of salicylaldehyde in the equatorial plane, and the coordination geometry can be described as a square.

Synthesis,Crystal Structure and Characterization of a Nickel Complex Based on Phenoxyimine Ligand and Catalysis of the Vinyl Polymerization of Norbornene

The title complex N,O-bis{2-[[（2-benzhydryl-4,6-dimethylphenyl）imino]-methyl]-phenol}-nickel（II）（C56H48N2NiO2） has been synthesized by the reaction of 2-[[（2-benzhydryl-4,6-dimethylphenyl）mino]-methyl]-phenol with Ni（CH3COO）2·4 H2O, and characterized by elemental analysis and IR spectrum. The spatial structure of the complex has been confirmed by single-crystal X-ray diffraction analysis. The compound belongs to the monoclinic system, space group C2/c with a = 39.035（8）, b = 13.276（3）, c = 17.679（4） A°, β = 98.06（3）°, V = 9071（3） A°^3, C56H48N2NiO2, Mr = 839.67, Z = 8, Dc = 1.230 Mg/m^3, μ = 0.472 mm^-1, F（000） = 3536, T = 293（2） K, the final R = 0.0675 and w R = 0.1345（I 〉 2s（I））. The compound showed excellent catalytic activity up to 1.268 × 10^7 g of PNB（mol of Ni）^-1h^-1 for the addition polymerization of norbornene by using methylaluminoxane（MAO） as a cocatalyst.

Syntheses, Crystal Structures and Photoluminescence Properties of Cadmium(Ⅱ) and Nickel(Ⅱ) Complexes with 2-(2-Benzimidazolyl)quinoline

Two novel complexes, [Cd2（BMQU）2Cl4] （1） and [Ni（BMQU）2HPO4]·1.5H2O （2） （BMQU = 2-（2-benzimidazolyl）quinoline）, were synthesized by the hydrothermal method and characterized by elemental analysis, IR, and TG-DTG. The crystal structures were determined by single-crystal X-ray diffraction. Both 1 and 2 crystallize in the triclinic system, space group P . The data for 1： a = 0.8342（7）, b = 0.9226（9）, c = 1.0646（8） nm, α = 90.819（2）, β = 97.466（2）, γ = 98.280（2）°. The Cd（Ⅱ） is coordinated with three chlorine atoms and two nitrogen atoms of a BMQU molecule, generating a distorted square-pyramidal geometry. The dinuclear Cd（Ⅱ） complex is formed by two chlorine bridge bonds, and the one-dimensional chain structure is constructed with the hydrogen bond N-H…Cl and π-π stacking interaction. The data for 2： a = 1.2251（1）, b = 1.2451（1）, c = 1.2868（1） nm, α = 107.510（2）, β = 98.630（1）, γ = 109.921（2）°. The Ni（Ⅱ） is coordinated with four nitrogen atoms of two BMQU molecules and two oxygen atoms of a HPO42-, forming a distorted-octahedral geometry. The two-dimensional layer structure is formed by the hydrogen bonds and π-π stacking interaction between neighboring molecules. Complex 1 shows a strong blue fluorescence emission （λmax= 456 nm） at solid state.

A Novel Phenoxyimine-based Schiff Base Ligand and Its Mononuclear Nickel(Ⅱ) Complex：Synthesis,Crystal Structure,Norbornene Polymerization and Catalytic Activity

A novel phenoxyimine-based Schiff base ligand and its mononuclear complex [C（58）H（52）N2NiO2]（L = 2-benzhydryl-4-dimethoxy-3,5-dimethyl-salicylaldehyde） has been synthesized and characterized by IR spectrum, elemental analysis, TG, WAXD spectra, ^1H NMR and ^（13）C NMR. In addition, the molecular structure has been measured by single-crystal X-ray diffraction analysis. The crystal belongs to the monoclinic system, space group P21/c with a = 14.510（6）, b = 18.573（7）, c = 20.961（6） A, β = 123.453（19）°, V = 4713（3）A^3, Mr = 867.73, Z = 4, Dc = 1.223 g/cm^3, μ = 0.456 mm^-1, F（000） = 1832, the final R = 0.0685 and wR = 0.1758（I 〉 2σ（I））. The complex was used as homogeneous catalysis of polymerization of norbornene, and the MAO as cocatalyst. The nickel complex exhibited good catalytic activity up to 1.913 × 10^7 g of PNB（mol of Ni）^-1h^-1,and the yields of these reactions depend on the nature of the substituent in the aromatic ring.

Electrokinetic-mechanism of water and furfural oxidation on pulsed laser-interlaced Cu_(2)O and CoO on nickel foam

The electrocatalytic oxidation of biomass-derived furfural(FF)feedstocks into 2-furoic acid(FA)holds immense industrial potential in optics,cosmetics,polymers,and food.Herein,we fabricated Co O/Ni O/nickel foam(NF)and Cu_(2)O/Ni O/NF electrodes via in situ pulsed laser irradiation in liquids(PLIL)for the bifunctional electrocatalysis of oxygen evolution reaction(OER)and furfural oxidation reaction(FOR),respectively.Simultaneous oxidation of NF surface to NiO and deposition of CoO and/or Cu_(2)O on NF during PLIL offer distinct advantages for enhancing both the OER and FOR.CoO/NiO/NF electrocatalyst provides a consistently low overpotential of~359 m V(OER)at 10 m A/cm^(2),achieving the maximum FA yield(~16.37 m M)with 61.5%selectivity,79.5%carbon balance,and a remarkable Faradaic efficiency of~90.1%during 2 h of FOR at 1.43 V(vs.reversible hydrogen electrode).Mechanistic pathway via in situ electrochemical-Raman spectroscopy on CoO/NiO/NF reveals the involvement of phase transition intermediates(NiOOH and CoOOH)as surface-active centers during electrochemical oxidation.The carbonyl carbon in FF is attacked by hydroxyl groups to form unstable hydrates that subsequently undergo further oxidation to yield FA products.This method holds promise for large-scale applications,enabling simultaneous production of renewable building materials and fuel.

Engineering of Self-Supported Electrocatalysts on a Three-Dimensional Nickel Foam Platform for Efficient Water Electrolysis

Economical water electrolysis requires highly active non-noble electrocatalysts to overcome the sluggish kinetics of the two half-cell reactions,oxygen evolution reaction,and hydrogen evolution reaction.Although intensive efforts have been committed to achieve a hydrogen economy,the expensive noble metal-based catalysts remain under consideration.Therefore,the engineering of self-supported electrocatalysts prepared using a direct growth strategy on three-dimensional(3D)nickel foam(NF)as a conductive substrate has garnered significant interest.This is due to the large active surface area and 3D porous network offered by these electrocatalysts,which can enhance the synergistic eff ect between the catalyst and the substrate,as well as improve electrocatalytic performance.Hydrothermal-assisted growth,microwave heating,electrodeposition,and other physical methods(i.e.,chemical vapor deposition and plasma treatment)have been applied to NF to fabricate competitive electrocatalysts with low overpotential and high stability.In this review,recent advancements in the development of self-supported electrocatalysts on 3D NF are described.Finally,we provide future perspectives of self-supported electrode platforms in electrochemical water splitting.