LiTFSI salt concentration effect to digest lithium polysulfides for high-loading sulfur electrodes

Sulfur utilization improvement and control of dissolved lithium polysulfide(LiPS;Li_(2)S x,2<x≤8)are cru-cial aspects of the development of lithium-sulfur(Li-S)batteries,especially in high-loading sulfur elec-trodes and low electrolyte/sulfur(E/S)ratios.The sluggish reaction in the low E/S ratio induces poor LiPS solubility and unstable Li_(2)S electrodeposition,resulting in limited sulfur utilization,especially under high-loading sulfur electrode.In this study,we report on salt concentration effects that improve sulfur utilization with a high-loading cathode(6 mgs ulfurcm^(-2)),a high sulfur content(80 wt%)and a low E/S ratio(5 m L gs ulfur^(-1)).On the basis of the rapid LiPS dissolving in a low concentration electrolyte,we estab-lished that the quantity of Li_(2)S electrodeposition from a high Li+diffusion coefficient,referring to the reduction of LiPS precipitation,was significantly enhanced by a faster kinetic.These results demonstrate the importance of kinetic factors for the rate capability and cycle life stability of Li-S battery electrolytes through high Li_(2)S deposition under high-loading sulfur electrode.

Electrochemical Degradation of Indigocarmine Dye at Ni/Graphite Modified Electrode in Aqueous Solution

Nickel Graphite modified electrode (Ni/GME) was prepared by electrochemical method and degradation of Indigocarmine (IC) dye was carried out. An investigation between the efficiency of degradation by graphite electrode and the Ni/graphite modified electrode has been carried out. The different effects of concentration, current density and temperature on the rate of degradation were studied. This study shows that the rate of the degradation is more for Ni doped modified graphite electrode. UV-Visible spectra before and after degradation of the dye solution were observed. The thin film formation of Ni or encapsulated in graphite rod is observed by scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM & EDAX). The instantaneous current effectiveness values of different experimental conditions are evaluated. The anodic oxidation by Ni/ graphite modified electrode showed the complete degradation of aqueous solution indigocarmine, which is confirmed by UV-Visible and chemical oxygen demand (COD) measurements. The dye is converted into CO2, H2O and simpler inorganic salts. The results observed for reuse of modified electrodes indicate that the Ni/graphite modified electrode would be a promising anode for electrochemical degradation of indigocarmine. This method can be applied for the remediation of waste water containing organics, cost-effective and simple.

Kinetics and Mechanism of Hypophosphite Electrooxidation on a Nickel Electrode

用电化学质谱(EMS)和动力学模型分析等方法研究了次亚磷酸根在镍电极上的电化学氧化机理和动力学.研究表明,次亚磷酸根的电化学氧化是通过从P-H键脱离一个原子H,形成磷中心自由基(PHO-●2),而磷中心自由基(PHO-●2)进一步进行电化学反应形成最终产物亚磷酸。利用该模型,推导出相关动力学方程并通过与实验数据拟合获得动力学参数.结果表明,该模型能很好地模拟次亚磷酸根在镍电极上的电化学氧化过程.

Dry electrode technology for scalable and flexible high-energy sulfur cathodes in all-solid-state lithium-sulfur batteries

All-solid-state lithium-sulfur batteries(ASSLSBs)employing sulfide solid electrolytes are one of the most promising next-generation energy storage systems due to their potential for higher energy density and safety.However,scalable fabrication of sheet-type sulfur cathodes with high sulfur loading and excellent performances remains challenging.In this work,sheet-type freestanding sulfur cathodes with high sulfur loading were fabricated by dry electrode technology.The unique fibrous morphologies of polytetrafluoroethylene(PTFE)binders in dry electrodes not only provides excellent mechanical properties but also uncompromised ionic/electronic conductance.Even employed with thickened dry cathodes with high sulfur loading of 2 mg cm^(-2),ASSLSBs still exhibit outstanding rate performance and cycle stability.Moreover,the all-solid-state lithium-sulfur monolayer pouch cells(9.2 m Ah)were also demonstrated and exhibited excellent safety under a harsh test situation.This work verifies the potential of dry electrode technology in the scalable fabrication of thickened sulfur cathodes and will promote the practical applications of ASSLSBs.

Effects of flaky rare earth oxide additives on the high temperature performance of nickel electrodes

Effects of flaky rare earth oxide additives including Er2O3,Tm2O3,and Yb2O3,Lu2O3 on high temperature and high rate discharge performance of nickel electrodes were investigated.The discharge efficiency at 0.2C reached 96% at 60 oC for electrodes with 1 at.% flaky rare earth oxides.The high rate discharge performance for electrodes with flaky rare earth oxides were improved significantly,for example,discharge efficiency at 5C improved from 50% to 70%.The results showed that the end charging potential of the ...

Electrocatalytic Oxidation of H_2 O_ 2 at a Carbon Paste Electrode Modified with a Nickel (Ⅱ)-5,11,17,23-Tetra-Tert-Butyl-25,27-Bis(Diethylcarbamoylmethoxy)Calix[4] Arene Complex and Its Application

Electrochemical behavior of a carbon paste electrode (CPE) modified with nickel(II)\|5, 11, 17, 23\|tetra\|tert\|butyl\|25, 27\|bis(diethylcarbamoylmethoxy)calix\arene (Ni(Ⅱ)\|L) complex and its electrocatalytic activity towards the oxidation of hydrogen peroxide were investigated by cyclic voltammetric technique in a 5.0×10 -2 mol/L NaClO 4+ 1.0×10 -3 mol/L NaOH solution. It was found that Ni(II)\|L acts as an effective catalyst for the oxidation of hydrogen peroxide. The modified electrode exhibited a linear response over a hydrogen peroxide concentrations in the range of 2.0×10 -6 \|1.0×10 -4 mol/L with a detection limit as low as 1.0×10 -6 mol/L. The relative standard deviation was 3.5% for 5 successive determinations of H 2 O 2 at 1.0×10 -5 mol/L. The modified electrode was used successfully in rainwater analysis.

Influence of TiO_2 on the electrochemical performance of pasted typeβ-nickel hydroxide electrode in alkaline electrolyte

Nickel hydroxide was used as the positive electrode material in rechargeable alkaline batteries, which plays a significant role in the field of electric energy storage devices. β-nickel hydroxide（β-Ni（OH）2 ） was prepared from nickel sulphate solution using potassium hydroxide as a precipitating agent. Pure β-phase of nickel hydroxide was confirmed from XRD and FT-IR studies. The effects of TiO2 additive on the β-Ni（OH）2 electrode performance are examined. The structure and property of the TiO2 added β-Ni（OH）2 were characterized by XRD, TG-DTA and SEM analysis. A pasted–type electrode is prepared using nickel hydroxide powder as the main active material on a nickel sheet as a current collector. Cyclic voltammetry and electrochemical impedance spectroscopy studies were performed to evaluate the electrochemical performance of the β-Ni（OH）2 and TiO2 added β-Ni（OH）2 electrodes in 6 M KOH electrolyte. Anodic（Epa） and cathodic（Epc）peak potentials are found to decrease after the addition of TiO 2 into β-Ni（OH）2 electrode material. Further,addition of TiO2 is found to enhance the reversibility of the electrode reaction and also increase the separation of the oxidation current peak of the active material from the oxygen evolution current. Compared with pure β-Ni（OH）2 lectrode,TiO2 added β-Ni（OH）2 electrode is found to exhibit higher proton diffusion coefficient（D） and lower charge transfer resistance. These findings suggest that the TiO2 added β-Ni（OH）2 electrode possess improved electrochemical properties and thus can be recognized as a promising candidate for the battery electrode applications.

Selective Heating of Transition Metal Usings Hydrogen Plasma and Its Application to Formation of Nickel Silicide Electrodes for Silicon Ultralarge-Scale Integration Devices

We developed an apparatus for producing high-density hydrogen plasma. The atomic hydrogen density was 3.1 × 1021 m?3 at a pressure of 30 Pa, a microwave power of 1000 W, and a hydrogen gas flow rate of 10 sccm. We confirmed that the temperatures of transition-metal films increased to above 800。C within 5 s when they were exposed to hydrogen plasma formed using the apparatus. We applied this phenomenon to the selective heat treatment of nickel films deposited on silicon wafers and formed nickel silicide electrodes. We found that this heat phenomenon automatically stopped after the nickel slicidation reaction finished. To utilize this method, we can perform the nickel silicidation process without heating the other areas such as channel regions and improve the reliability of silicon ultralarge-scale integration devices.

Recent advances in cobalt-, nickel-, and iron-based chalcogen compounds as counter electrodes in dye-sensitized solar cells

The electroactive materials used in the counter electrode(CE)are of great concern as they influence the photovoltaic performances of dye-sensitized solar cells.The main functions of CE materials are collecting electrons from the external circuit and transferring them to the electrolyte and realizing the catalytic reduction of the redox species(I3^– or Co^3+)present in the electrolyte.The research hotspot of CE materials is seeking functional materials that display high efficiency,low cost,and good electrochemical stability and can substitute the benchmark platinum electrode.Chalcogen compounds of cobalt,nickel,and iron have been widely applied as CE materials and exhibit excellent electrocatalytic performances owing to their unique electrical properties,similar energies of adsorption of I atoms as platinum,excellent catalytic activities,and good chemical stabilities.In this review,we trace the developments and performances of chalcogen compounds of iron,cobalt,and nickel as CE materials and present the latest research directions for improving the electrocatalytic performances.We then highlight the optimization strategies for further improving their performances,such as fabrication of architectures,regulation of the components,synthesis of composites containing carbon materials,and elemental doping.

Plastic supported platinum modified nickel electrode and its high electrocatalytic activity for sodium borohydride electrooxidation

A novel plastic/multi-walled carbon nanotube（MWNTs）-nickel（Ni）-platinum（Pt） electrode（PMNP） is prepared by chemical-reducing Pt onto the surface of Ni film covered plastic/MWNTs（PM） substrate. The MWNTs are adhered by a piece of commercial double faced adhesive tape on the surface of plastic paper and the Ni film is prepared by a simple electrodeposition method. The morphology and phase structure of the PMNP electrode are characterized by scanning electron microscopy,transmission electron microscope and X-ray diffractometer. The catalytic activity of the PMNP electrode for Na BH4 electrooxidation is investigated by means of cyclic voltammetry and chronoamperometry. The catalyst combines tightly with the plastic paper and exhibits a good stability. MWNTs serve as both conductive material and hydrogen storage material and the Ni film and Pt are employed as electrochemical catalysts. The PMNP electrode exhibits a high electrocatalytic performance and the oxidation current density reaches to 10.76 A/（mg·cm） in 0.1 mol/dm3 Na BH4at0 V,which is much higher than those in the previous reports. The using of waste plastic reduces the discarding of white pollution and consumption of metal resources.

Synergistic effect of cobalt and copper on a nickel-based modified graphite electrode during methanol electro-oxidation in NaOH solution

The electrocatalytic oxidation of methanol was studied over Ni, Co and Cu binary or ternary alloys on graphite electrodes in a NaOH solution （0.1 mol/L）. The catalysts were prepared by cycling the graphite electrode in solutions containing Ni, Cu and Co ions at cathodic potentials. The synergistic effects and catalytic activity of the modified electrodes were investigated by cyclic voltammetry （CV）, chronoamperometry CCA） and electrochemical impedance spectroscopy （EIS）. It was found that, in the presence of methanol, the modified Ni-based ternary alloy electrode （G/NiCuCo） exhibited a significantly higher response for methanol oxidation compared to the other samples. The anodic peak currents showed a linear dependency on the square root of the scan rate, which is a characteristic of a diffusion controlled process. During CA studies, the reaction exhibited Cottrellin behavior and the diffusion coefficient of methanol was determined to be 6.25× 10-6 cm2/s and the catalytic rate constant, K, for methanol oxidation was found to be 40×107 cm3/Cmol.s）. EIS was used to investigate the catalytic oxidation of methanol on the surface of the modified electrode.

A Review on Engineering Design for Enhancing Interfacial Contact in Solid-State Lithium–Sulfur Batteries

The utilization of solid-state electrolytes(SSEs)presents a promising solution to the issues of safety concern and shuttle effect in Li–S batteries,which has garnered significant interest recently.However,the high interfacial impedances existing between the SSEs and the electrodes(both lithium anodes and sulfur cathodes)hinder the charge transfer and intensify the uneven deposition of lithium,which ultimately result in insufficient capacity utilization and poor cycling stability.Hence,the reduction of interfacial resistance between SSEs and electrodes is of paramount importance in the pursuit of efficacious solid-state batteries.In this review,we focus on the experimental strategies employed to enhance the interfacial contact between SSEs and electrodes,and summarize recent progresses of their applications in solidstate Li–S batteries.Moreover,the challenges and perspectives of rational interfacial design in practical solid-state Li–S batteries are outlined as well.We expect that this review will provide new insights into the further technique development and practical applications of solid-state lithium batteries.

EFFECT OF ELECTROLESS PLATING COBALT UPON CHARACTERISTICS OF NICKEL HYDROXIDE ELECTRODEFORRECHARGEABLEALKALINEBATTERIES

ＩＮＴＲＯＤＵＣＴＩＯＮＮｉｃｋｅｌｈｙｄｒｏｘｉｄｅｅｌｅｃｔｒｏｄｅｓｈａｖｅｂｅｅｎｗｉｄｅｌｙｕｓｅｄａｓｐｏｓｉｔｉｖｅｅｌｅｃｔｒｏｄｅｉｎＮｉＣｄ，ＮｉＨ２ａｎｄＮｉＭＨｓｅｃｏｎｄａｒｙｂａｔｅｒｉｅｓ．Ｉｍｐｒｏｖｅｍｅｎｔ...

Kinetic Model of Hypophosphite Oxidation on a Nickel Electrode in D_2O Solution

Kinetic model of hypophosphite oxidation on a nickel electrode was studied in D2O solution in order to reach a better understanding of the oxidation mechanism. In the model;he electrooxidation of hypophosphite undergo a H abstraction of hypophosphite from the P-H bond to form the phosphorus-centered radical (PWO2-)-P-., which subsequently is electrochemically reacted with water to form the final product, phosphite. The kinetic equations were derived, and the kinetic parameters were obtained from a comparison of experimental results and the kinetic equations. The process of hypophosphite electrooxidation could be well simulated by this model.

Voltammetric Response and Electrocatalysis of Glassy Carbon Electrode Modified with Monolayer Nickel Hydroxide

The glassy carbon (GC) electrode modified with a monolayer nickel hydroxide (GC/Ni(OH) 2) was prepared by immersion of GC substrate in 1.0×10 -3 mol/L NiSO 4 solution, and then cyclic voltammetric scanning in 0.20 mol/L KOH. Similarly, GC/Co(OH) 2 electrode was prepared too. The experiments showed that the voltammetric behavior of GC/Ni(OH) 2 electrode in 0.20 mol/L KOH is more stable than that of GC/ Co(OH) 2. It was found that the GC/Ni(OH) 2 electrode acts as an effective electrocatalysis for the oxidation of hydrazine.

Electrooxidation of Mn(Ⅱ) on Pb-Sb-As Electrode in Sulfuric Acid

The electrooxidation of Mn(Ⅱ) on Pb Sb As alloy electrode in sulfuric acid has been investigated.In order to make the two steps of indirect electrosynthesis of benzaldehyde carried out in the same sulfuric acid concentration and also obtain high current efficiency of Mn(Ⅱ) to Mn(Ⅲ) and high yield of Mn(Ⅲ) oxidizing toluene to benzaldehyde in the mean time,the electrooxidation of Mn(Ⅱ) in 60% H 2SO 4 has been studied.Experimental results show that high current efficiency of Mn(Ⅲ) (about 75%) is obtained in 60%H 2SO 4 at 60℃.The reason affecting the current efficiency of Mn(Ⅲ) is discussed,and it is the coordination of sulfuric acid concentration and electrolytic temperature.The law is found that it is suitable for electrolysis at low temperature when sulfuric acid concentration is low and at high temperature when sulfuric acid concentration is high.

ELECTRO－OXIDATION OF ETHANOL ON HIGHLY PREFERRED ORIENTATION NICKEL ELECTRODE IN NaOH

The electro-oxidation of ethanol on a highly preferred orientation (220) Ni electrode and alower texture degree Ni electrode in 1 mol/L NaoH was investigated with cyclicvoltammetry. The mechanism of ethanol oxidation on the highly preferred orientation Nielectrode is proposed. It is shown that the current peak of electro-oxidation of ethanol onthe highly preferred orientation (220) Ni electrode is much higher than that of the lowertextUre degree (220) Ni electrode, Ni(Ⅲ) on the surface of the highly preferredorientation(220)Ni electrode is responsible for the oxidation ethanol.

Valence modulated nickel oxynitride network as integrated bifunctional electrodes for enhanced energy storage

As promising electrode materials,transition metal oxides have attracted considerable attention owing to their excellent performance in electrochemical energy storage.However,their poor conductivity and fragile structure limit their practical application.In this study,a binder-free nickel oxide/oxynitride network(NiON WS)bifunctional electrodes with cation multivalent states that exhibit high energy storage performance were synthesized for the first time.The massive active sites,high specific surface areas,and multiple cation valence states of NiON WS were advantageous for electrochemical redox reaction during its application in supercapacitors(1283.5 mF cm^(-2))and lithium-ion batteries(1345.0 mA h g^(-1)).Particularly,the NiON WS based flexible asymmetric SCs exhibit excellent capacitance and energy densities.First-principle calculations were employed to study the mechanism of the electrochemical performance improvement of NiON WS.This study demonstrates the potential of transition metal oxides electrode with high capacity and activity for electrochemical energy storage and conversion.

Electroless Co-Zn Surface-Modified Nickel Hydroxide as an Active Material for Pasted Nickel Electrodes

Chemically precipitated β type nickel hydroxide powder was surface modified by electroless deposition of Co Zn coatings,and physical properties of both the modified and unmodified nickel hydroxide were characterized by scanning electron microscopy (SEM), specific surface area (BET), X ray diffraction (XRD) and X ray photoelectron spectroscopy (XPS). It has been found that Co and Zn components of the surface electroless coatings exist in the oxidized state. Electrochemical performances of pasted nickel electrodes using the modified nickel hydroxide as an active material were investigated, and compared with those of the electrodes prepared with the unmodified nickel hydroxide. Charge/discharge tests show that the modified nickel hydroxide electrodes exhibit better performances in the charge efficiency, specific discharge capacity and active material utilization. Their resistance to swelling with cycling is also superior to that of the unmodified nickel hydroxide electrodes. Cyclic voltammetric (CV) studies indicate that the modified electrodes have a higher electrochemical activity, and the porous pasted nickel electrodes have some distinguished CV characteristics in comparison with those of the thin film nickel electrodes.

A STUDY ON Ti ELECTRODE MODIFIED BY NICKEL ION BEANS

The reduction of H^+ on Ti electrodes which were treated by implanting nickel ions and thermodiffusing in vacuum has been studied.The calytic activity of the afore- mentioned electroes for H^+ reduction is much higher than that of the untreated Ti electrodes.