Atomic simulations are executed to investigate the creep responses of nano-polycrystalline(NC) niobium established by using the Voronoi algorithm. The effects of varying temperature, applied stress, and grain size(GS)...Atomic simulations are executed to investigate the creep responses of nano-polycrystalline(NC) niobium established by using the Voronoi algorithm. The effects of varying temperature, applied stress, and grain size(GS) on creep properties and mechanisms are investigated. Notably, the occurrence of tertiary creep is exclusively observed under conditions where the applied stress exceeds 4.5 GPa and the temperature is higher than 1100 K. This phenomenon can be attributed to the significant acceleration of grain boundary and lattice diffusion, driven by the elevated temperature and stress levels. It is found that the strain rate increases with both temperature and stress increasing. However, an interesting trend is observed in which the strain rate decreases as the grain size increases. The stress and temperature are crucial parameters governing the creep behavior. As these factors intensify, the creep mechanism undergoes a sequential transformation: initially from lattice diffusion under low stress and temperature conditions to a mixed mode combining grain boundaries(GBs) and lattice diffusion at moderate stress and mid temperature levels, and ultimately leading to the failure of power-law controlled creep behavior, inclusive of grain boundary recrystallization under high stress and temperature conditions. This comprehensive analysis provides in more detail an understanding of the intricate creep behavior of nano-polycrystalline niobium and its dependence on various physical parameters.展开更多
The aim of this study of the spatial dispersion of tin, niobium and tantalum mineralization associated with the Mayo Darlé granitoids was to produce prospecting guides through predictive maps of Sn, Nb and Ta in ...The aim of this study of the spatial dispersion of tin, niobium and tantalum mineralization associated with the Mayo Darlé granitoids was to produce prospecting guides through predictive maps of Sn, Nb and Ta in the region. It was based on a database (in appendix) obtained after analysis of rock samples (greisens and quartz veins) collected in the field, using a portable X-ray fluorescence (XRF) spectrometer. Two approaches were used: 1) structural studies in the field using the directions of veins and fractures 2) the use of variographic maps, an essential element in geostatistics for determining directional anisotropies. A joint synthesis of the modelling results shows that tin, tantalum and niobium mineralization at Mayo Darlé is concentrated along strike intervals N315E to N320E, with mineralization also occurring along strike N35E for high-grade Sn, medium-grade Ta and low-grade Nb. In short, mineral concentrations disperse progressively in space: positively from east to west for tantalum and niobium, and inversely for tin.展开更多
Niobium pentoxide(Nb_(2)O_(5))anodes have gained increasing attentions for high-power lithium-ion batteries owing to the outstanding rate capability and high safety.However,Nb2O5 anode suffers poor cycle stability eve...Niobium pentoxide(Nb_(2)O_(5))anodes have gained increasing attentions for high-power lithium-ion batteries owing to the outstanding rate capability and high safety.However,Nb2O5 anode suffers poor cycle stability even after modified and the unrevealed mechanisms have restricted the practical applications.Herein,the over-reduction of Nb5+has been demonstrated to be the critical reason for the capacity loss for the first time.Besides,an effective competitive redox strategy has been developed to solve the rapid capacity decay of Nb_(2)O_(5),which can be achieved by the incorporation of vanadium to form a new rutile VNbO_(4)anode.The highly reversible V^(3+)/V^(2+)redox couple in VNbO_(4)can effectively inhibit the over-reduction of Nb^(5+).Besides,the electron migration from V^(3+)to Nb5+can greatly increase the intrinsic electronic conductivity for VNbO4.As a result,VNbO4 anode delivers a high capacity of 206.1 mAh g^(−1)at 0.1 A g^(−1),as well as remarkable cycle performance with a retention of 93.4%after 2000 cycles at 1.0 A g^(−1).In addition,the assembled lithium-ion capacitor demonstrates a high energy density of 44 Wh kg^(−1)at 5.8 kW kg^(−1).In summary,our work provides a new insight into the design of ultra-fast and durable anodes.展开更多
This work demonstrates the viability of the powder-mixed micro-electrochemical discharge machining(PMECDM) process to fabricate micro-holes on C103 niobium-based alloy for high temperature applications.Three processes...This work demonstrates the viability of the powder-mixed micro-electrochemical discharge machining(PMECDM) process to fabricate micro-holes on C103 niobium-based alloy for high temperature applications.Three processes are involved simultaneously i.e.spark erosion,chemical etching,and abrasive grinding for removal of material while the classical electrochemical discharge machining process involves double actions i.e.spark erosion,and chemical etching.The powder-mixed electrolyte process resulted in rapid material removal along with a better surface finish as compared to the classical microelectrochemical discharge machining(MECDM).Further,the results are optimized through a multiobjective optimization approach and study of the surface topography of the hole wall surface obtained at optimized parameters.In the selected range of experimental parameters,PMECDM shows a higher material removal rate(MRR) and lower surface roughness(R_(a))(MRR:2.8 mg/min and R_(a) of 0.61 μm) as compared to the MECDM process(MRR:2.01 mg/min and corresponding Raof 1.11 μm).A detailed analysis of the results is presented in this paper.展开更多
The hot-roll bonding was carried out in vacuum between titanium alloy and stainless steel using niobium interlayer. The interfacial structure and mechanical properties were analyzed. The results show that the plastici...The hot-roll bonding was carried out in vacuum between titanium alloy and stainless steel using niobium interlayer. The interfacial structure and mechanical properties were analyzed. The results show that the plasticity of bonded joint is improved significantly. When the bonding temperature is 800 °C or 900 °C, there is not intermetallic layer at the interface between stainless steel and niobium. When the bonding temperature is 1000 °C or 1050 °C, Fe-Nb intermetallic layer forms at the interface. When the bonding temperature is 1050 °C, cracking occurs between stainless steel and intermetallic layer. The maximum strength of -417.5 MPa is obtained at the bonding temperature of 900 °C, the reduction of 25% and the rolling speed of 38 mm/s, and the tensile specimen fractures in the niobium interlayer with plastic fracture characteristics. When the hot-roll bonded transition joints were TIG welded with titanium alloy and stainless steel respectively, the tensile strength of the transition joints after TIG welding is -410.3 MPa, and the specimen fractures in the niobium interlayer.展开更多
The segregation during solidification and high temperature diffusion during homogenization of niobium in a highly alloyed nickel-base superalloy were investigated.Niobium is seriously segregated into the interdendriti...The segregation during solidification and high temperature diffusion during homogenization of niobium in a highly alloyed nickel-base superalloy were investigated.Niobium is seriously segregated into the interdendritic regions with segregation coefficient as high as 4.30.Various niobium-enriched phases including Laves phase,δ phase,（γ＋γ＇） eutectic,MC and M6C types of carbides precipitated in the interdendritic regions.The soluble temperature of niobium-enriched phases and the degree of dendritic segregation were determined by differential thermal analysis and homogenization treatments at varied temperatures and times.The calculation of elemental diffusion indicates that the diffusion rate of niobium increases remarkably with the homogenization temperature increasing,so that the annealing time can be effectively reduced.A three-step homogenization treatment technology without incipient melting was established to eliminate the segregation of niobium and to obtain a uniform microstructure.展开更多
基金Project supported by the Doctoral Scientific Research Starting Foundation of Nanchang Hang Kong University,China(Grant No.EA201903209)。
文摘Atomic simulations are executed to investigate the creep responses of nano-polycrystalline(NC) niobium established by using the Voronoi algorithm. The effects of varying temperature, applied stress, and grain size(GS) on creep properties and mechanisms are investigated. Notably, the occurrence of tertiary creep is exclusively observed under conditions where the applied stress exceeds 4.5 GPa and the temperature is higher than 1100 K. This phenomenon can be attributed to the significant acceleration of grain boundary and lattice diffusion, driven by the elevated temperature and stress levels. It is found that the strain rate increases with both temperature and stress increasing. However, an interesting trend is observed in which the strain rate decreases as the grain size increases. The stress and temperature are crucial parameters governing the creep behavior. As these factors intensify, the creep mechanism undergoes a sequential transformation: initially from lattice diffusion under low stress and temperature conditions to a mixed mode combining grain boundaries(GBs) and lattice diffusion at moderate stress and mid temperature levels, and ultimately leading to the failure of power-law controlled creep behavior, inclusive of grain boundary recrystallization under high stress and temperature conditions. This comprehensive analysis provides in more detail an understanding of the intricate creep behavior of nano-polycrystalline niobium and its dependence on various physical parameters.
文摘The aim of this study of the spatial dispersion of tin, niobium and tantalum mineralization associated with the Mayo Darlé granitoids was to produce prospecting guides through predictive maps of Sn, Nb and Ta in the region. It was based on a database (in appendix) obtained after analysis of rock samples (greisens and quartz veins) collected in the field, using a portable X-ray fluorescence (XRF) spectrometer. Two approaches were used: 1) structural studies in the field using the directions of veins and fractures 2) the use of variographic maps, an essential element in geostatistics for determining directional anisotropies. A joint synthesis of the modelling results shows that tin, tantalum and niobium mineralization at Mayo Darlé is concentrated along strike intervals N315E to N320E, with mineralization also occurring along strike N35E for high-grade Sn, medium-grade Ta and low-grade Nb. In short, mineral concentrations disperse progressively in space: positively from east to west for tantalum and niobium, and inversely for tin.
基金support from National Natural Science Foundation of China(51874142)Tip-top Scientific and Technical Innovative Youth Talents of Guangdong Special Support Program(2019TQ05L903)Young Elite Scientists Sponsorship Program by CAST(2019QNRC001).
文摘Niobium pentoxide(Nb_(2)O_(5))anodes have gained increasing attentions for high-power lithium-ion batteries owing to the outstanding rate capability and high safety.However,Nb2O5 anode suffers poor cycle stability even after modified and the unrevealed mechanisms have restricted the practical applications.Herein,the over-reduction of Nb5+has been demonstrated to be the critical reason for the capacity loss for the first time.Besides,an effective competitive redox strategy has been developed to solve the rapid capacity decay of Nb_(2)O_(5),which can be achieved by the incorporation of vanadium to form a new rutile VNbO_(4)anode.The highly reversible V^(3+)/V^(2+)redox couple in VNbO_(4)can effectively inhibit the over-reduction of Nb^(5+).Besides,the electron migration from V^(3+)to Nb5+can greatly increase the intrinsic electronic conductivity for VNbO4.As a result,VNbO4 anode delivers a high capacity of 206.1 mAh g^(−1)at 0.1 A g^(−1),as well as remarkable cycle performance with a retention of 93.4%after 2000 cycles at 1.0 A g^(−1).In addition,the assembled lithium-ion capacitor demonstrates a high energy density of 44 Wh kg^(−1)at 5.8 kW kg^(−1).In summary,our work provides a new insight into the design of ultra-fast and durable anodes.
文摘This work demonstrates the viability of the powder-mixed micro-electrochemical discharge machining(PMECDM) process to fabricate micro-holes on C103 niobium-based alloy for high temperature applications.Three processes are involved simultaneously i.e.spark erosion,chemical etching,and abrasive grinding for removal of material while the classical electrochemical discharge machining process involves double actions i.e.spark erosion,and chemical etching.The powder-mixed electrolyte process resulted in rapid material removal along with a better surface finish as compared to the classical microelectrochemical discharge machining(MECDM).Further,the results are optimized through a multiobjective optimization approach and study of the surface topography of the hole wall surface obtained at optimized parameters.In the selected range of experimental parameters,PMECDM shows a higher material removal rate(MRR) and lower surface roughness(R_(a))(MRR:2.8 mg/min and R_(a) of 0.61 μm) as compared to the MECDM process(MRR:2.01 mg/min and corresponding Raof 1.11 μm).A detailed analysis of the results is presented in this paper.
基金Project(AWPT-M07)supported by State Key Laboratory of Advanced Welding and Joining,ChinaProject(20120041120015)supported by Specialized Research Fund for the Doctoral Program of Higher Education,China
文摘The hot-roll bonding was carried out in vacuum between titanium alloy and stainless steel using niobium interlayer. The interfacial structure and mechanical properties were analyzed. The results show that the plasticity of bonded joint is improved significantly. When the bonding temperature is 800 °C or 900 °C, there is not intermetallic layer at the interface between stainless steel and niobium. When the bonding temperature is 1000 °C or 1050 °C, Fe-Nb intermetallic layer forms at the interface. When the bonding temperature is 1050 °C, cracking occurs between stainless steel and intermetallic layer. The maximum strength of -417.5 MPa is obtained at the bonding temperature of 900 °C, the reduction of 25% and the rolling speed of 38 mm/s, and the tensile specimen fractures in the niobium interlayer with plastic fracture characteristics. When the hot-roll bonded transition joints were TIG welded with titanium alloy and stainless steel respectively, the tensile strength of the transition joints after TIG welding is -410.3 MPa, and the specimen fractures in the niobium interlayer.
文摘The segregation during solidification and high temperature diffusion during homogenization of niobium in a highly alloyed nickel-base superalloy were investigated.Niobium is seriously segregated into the interdendritic regions with segregation coefficient as high as 4.30.Various niobium-enriched phases including Laves phase,δ phase,（γ＋γ＇） eutectic,MC and M6C types of carbides precipitated in the interdendritic regions.The soluble temperature of niobium-enriched phases and the degree of dendritic segregation were determined by differential thermal analysis and homogenization treatments at varied temperatures and times.The calculation of elemental diffusion indicates that the diffusion rate of niobium increases remarkably with the homogenization temperature increasing,so that the annealing time can be effectively reduced.A three-step homogenization treatment technology without incipient melting was established to eliminate the segregation of niobium and to obtain a uniform microstructure.
