To replace nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to lower the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturated nitr...To replace nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to lower the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturated nitrogen content in the stainless steel was developed and the model was validated by experimental measurements performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the molten steel with a top lance. Thus, the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen flow rate on the transfer of nitrogen to the steel were investigated and discussed. The results showed that the dissolution rate of nitrogen in the molten steel increases with a higher temperature and larger nitrogen flow rate but decreases significantly with an increase in the content of surface- active elements. Alloying elements such as chromium and manganese having a negative interaction coefficient can increase the dissolution of nitrogen in the molten steel. It was also proposed that the primary factor affecting the final saturated nitrogen content is temperature rather than the dissolved oxygen content.展开更多
Microstructure, hardness and fatigue properties of X30N high nitrogen stainless bearing steel were investigated. It was found that nitrogen addition could effectively reduce the amount and size of coarse carbides. The...Microstructure, hardness and fatigue properties of X30N high nitrogen stainless bearing steel were investigated. It was found that nitrogen addition could effectively reduce the amount and size of coarse carbides. The original austenite grain size was obviously refined. Additionally, more retained austenite was found in X30N steel after quenching at 1050 ℃, which could be reduced from about 30% to about 6% by cold treatment at - 73 ℃ and subsequent tempering, and thus, the ultimate hardness was increased up to about 61 HRC with reduction of austenite and precipitation of carbonitrides. Furthermore, the rolling contact fatigue lives of X30N steel ate superior to those of 440C steel, which was attributed to the enhanced hardness and a certain retained austenite in the high nitrogen steel.展开更多
基金Item Sponsored by National Natural Science Foundation of China (51074021)Doctoral Programs Foundation of Ministry of Education of China (200800080016)
文摘To replace nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to lower the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturated nitrogen content in the stainless steel was developed and the model was validated by experimental measurements performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the molten steel with a top lance. Thus, the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen flow rate on the transfer of nitrogen to the steel were investigated and discussed. The results showed that the dissolution rate of nitrogen in the molten steel increases with a higher temperature and larger nitrogen flow rate but decreases significantly with an increase in the content of surface- active elements. Alloying elements such as chromium and manganese having a negative interaction coefficient can increase the dissolution of nitrogen in the molten steel. It was also proposed that the primary factor affecting the final saturated nitrogen content is temperature rather than the dissolved oxygen content.
基金This research is supported by the National Natural Science Foundation of China （No. 51371057）, the National Key Research and Development Plan （No. 2016YFB0300101） and Beijing Natural Science Foundation （No. 2182088）.
文摘Microstructure, hardness and fatigue properties of X30N high nitrogen stainless bearing steel were investigated. It was found that nitrogen addition could effectively reduce the amount and size of coarse carbides. The original austenite grain size was obviously refined. Additionally, more retained austenite was found in X30N steel after quenching at 1050 ℃, which could be reduced from about 30% to about 6% by cold treatment at - 73 ℃ and subsequent tempering, and thus, the ultimate hardness was increased up to about 61 HRC with reduction of austenite and precipitation of carbonitrides. Furthermore, the rolling contact fatigue lives of X30N steel ate superior to those of 440C steel, which was attributed to the enhanced hardness and a certain retained austenite in the high nitrogen steel.
