Al_(2)O_(3)-MgO and Al_(2)O_(3)-spinel low cement castables(LCC-AM and LCC-AS)have been extensively used in steel ladles as working linings.Nevertheless,the use of alumina-magnesia gunning mixes has been mainly kept f...Al_(2)O_(3)-MgO and Al_(2)O_(3)-spinel low cement castables(LCC-AM and LCC-AS)have been extensively used in steel ladles as working linings.Nevertheless,the use of alumina-magnesia gunning mixes has been mainly kept for maintaining these castable linings,because of high rebound loss,poor green strength,high porosity and short life-span.Thanks to a high BET alumina(MC-G),it is now possible to develop a series of high-performance no-cement or low-cement Al_(2)O_(3)-MgO gunning mixes(NCG-AM or LCG-AM).The paper focuses on the BOF slag resistance of NCG-AM,LCG-AM,LCC-AM and LCC-AS.The corrosion mechanisms of rotary slag samples were studied by scanning electron microscopy(SEM/EDS).The results reveal different microstructures around MgO particles,depending on the four used compositions.Continuous and thicker spinel phases were formed in NCG-AM,which was proved to have the best corrosion resistance after the dynamic slag test.MC-G can provide a high diffusion flux of Al^(3+)in terms of kinetics and hence inhibits Kirkendall porosity around MgO particles.In addition,a continuous spinel phase acts like a pinning nail to reinforce the matrix and thus decreases erosion by slag.In contrast to NCG-AM,the porous spinel phase was found around unreacted MgO particles and some particles were carried away near the interface of LCC-AM and slag.The NCG-AM containing MC-G had been tested in two steel plants,and it extended the service life of the ladles up to 50%.In addition,this study suggests the potential application of NCG-AM as steel ladle linings.展开更多
Microsilica-gel bonded bauxite based no-cement refractory castables（NCCs）have been produced using two readily available dispersants.These NCCs were compared to NCC with Siox X-Zero,a purposely-developed product for ...Microsilica-gel bonded bauxite based no-cement refractory castables（NCCs）have been produced using two readily available dispersants.These NCCs were compared to NCC with Siox X-Zero,a purposely-developed product for microsilica-gel bonded no-cement castable systems to control flow properties and setting characteristics.Three mixing and curing temperatures were applied：5℃,20℃and 35℃.The results show that setting-behaviour and mechanical properties strongly vary with the type of dispersant and the curing temperature.However,both setting and strength are less temperature dependent in the castables with Siox X-Zero.Furthermore,the drying and firing of microsilica-gel bonded NCCs were investigated.Since microsilica-gel bond system contains only a small amount of bound water,the castables can be fired at very high heating rates,once the free water has been removed.展开更多
文摘Al_(2)O_(3)-MgO and Al_(2)O_(3)-spinel low cement castables(LCC-AM and LCC-AS)have been extensively used in steel ladles as working linings.Nevertheless,the use of alumina-magnesia gunning mixes has been mainly kept for maintaining these castable linings,because of high rebound loss,poor green strength,high porosity and short life-span.Thanks to a high BET alumina(MC-G),it is now possible to develop a series of high-performance no-cement or low-cement Al_(2)O_(3)-MgO gunning mixes(NCG-AM or LCG-AM).The paper focuses on the BOF slag resistance of NCG-AM,LCG-AM,LCC-AM and LCC-AS.The corrosion mechanisms of rotary slag samples were studied by scanning electron microscopy(SEM/EDS).The results reveal different microstructures around MgO particles,depending on the four used compositions.Continuous and thicker spinel phases were formed in NCG-AM,which was proved to have the best corrosion resistance after the dynamic slag test.MC-G can provide a high diffusion flux of Al^(3+)in terms of kinetics and hence inhibits Kirkendall porosity around MgO particles.In addition,a continuous spinel phase acts like a pinning nail to reinforce the matrix and thus decreases erosion by slag.In contrast to NCG-AM,the porous spinel phase was found around unreacted MgO particles and some particles were carried away near the interface of LCC-AM and slag.The NCG-AM containing MC-G had been tested in two steel plants,and it extended the service life of the ladles up to 50%.In addition,this study suggests the potential application of NCG-AM as steel ladle linings.
文摘Microsilica-gel bonded bauxite based no-cement refractory castables（NCCs）have been produced using two readily available dispersants.These NCCs were compared to NCC with Siox X-Zero,a purposely-developed product for microsilica-gel bonded no-cement castable systems to control flow properties and setting characteristics.Three mixing and curing temperatures were applied：5℃,20℃and 35℃.The results show that setting-behaviour and mechanical properties strongly vary with the type of dispersant and the curing temperature.However,both setting and strength are less temperature dependent in the castables with Siox X-Zero.Furthermore,the drying and firing of microsilica-gel bonded NCCs were investigated.Since microsilica-gel bond system contains only a small amount of bound water,the castables can be fired at very high heating rates,once the free water has been removed.
