Noise level estimation method with application to EMD-based signal denoising

This paper proposes a new signal noise level estimation approach by local regions. The estimated noise variance is applied as the threshold for an improved empirical mode decomposition（EMD） based signal denoising method. The proposed estimation method can effectively extract the candidate regions for the noise level estimation by measuring the correlation coefficient between noisy signal and a Gaussian filtered signal. For the improved EMD based method, the situation of decomposed intrinsic mode function（IMFs） which contains noise and signal simultaneously are taken into account. Experimental results from two simulated signals and an X-ray pulsar signal demonstrate that the proposed method can achieve better performance than the conventional EMD and wavelet transform（WT） based denoising methods.

Determination of the Sound Absorption Capacity of Hydraulic Concrete Mixtures Added with Waste Tire Rubber

There are different types of pollutants that are harmful to the environment, including smog, chemicals that are dumped into rivers, scrap tires, etc. The latter have the particularity that it is not possible to recycle them to manufacture new tires. In the present work, hydraulic concrete plates added with waste tire rubber were manufactured to modify their sound absorption capacity. It was found that the rubber additions produce changes in the density of the material and in the sound absorption capacity. When the material is exposed to high-frequency sounds that correspond to high-pitched sounds, its absorption capacity increases. On the contrary, when the test frequency is low, that is, bass sounds, the sound absorption capacity decreases. The results obtained in this work suggest that the proposed mixtures are suitable for the possible manufacture of acoustic insulating shields.

Sintering preparation of porous sound-absorbing materials from steel slag

Porous sound-absorbing materials were prepared from steel slag using waste expanded polystyrene（EPS） particles as pore former.The influences of the experimental conditions such as fly ash content,sintering temperature,sintering time,and pore former addition on the performance of the porous sound-absorbing materials were investigated.The results show that the porosity of the specimens can reach above 50.0%;the compressive strength and average sound-adsorption coefficient of the sintered specimens are above 3.0 MPa and 0.47,respectively.The optimum preparation conditions for the steel slag porous sound-absorbing materials are as follows：mass fraction of fly ash 50%,waste EPS particles 3.6 g,sintering temperature 1100℃,and sintering time 7.5h,which are determined by considering the properties of the sound-absorbing materials,energy consumption and cost.

Identification of Modal Parameters with Linear Structure under Non-stationary Ambient Excitation

Empirical mode decomposition (EMD) is proposed to identify linear structure under non-stationary excitation,and non-white noise coefficient is introduced under the assumption of random signals consisting of white noise and non-white noise signals. The cross-correlation function of response signal is decomposed into mode functions and residue by EMD method. The identification technique of the modal parameters of single freedom degree is applied to each mode function to obtain natural frequencies, damping ratios and mode shapes. The results of identification of the five-degree freedom linear system demonstrate that the proposed method is effective in identifying the parameters of linear structures under non-stationary ambient excitation.

Detection performance analysis for MIMO radar with distributed apertures in Gaussian colored noise

This paper establishes the classic linear model of signal of the MIMO radar system with distributed apertures. Based on this model, the design principle and detection performance of MIMO radar detector is investigated under conditions of Gaussian colored noise and partially correlated observation channels. First, the research on design principle of detector shows that the clutter suppression and matched filtering can be independently implemented at each receiving aperture, which greatly reduces the difficulty in implementation of these detectors. Based on these results, a Max detector is proposed for the case where partial channels are disabled due to strong noise and stealth techniques. The second part is the performance analysis of detector. The Fishier divergence coefficient and the statistical equivalent decomposition of limit statistics are used to theoretically analyze the detection performance of AMF detector, and then the analytical expressions of the detection performance of the AMF detector is derived. Analysis results show that both the colored nature of noise and the correlation among observation channels can reduce the capability of spatial diversity of the MIMO radar system, change the target RCSs among observation channels from quick fluctuation to slow fluctuation, and degenerate the detection performance of this radar system into that of the phased array radar system at high signal-to-noise ratio.

Preparation of steel slag porous sound-absorbing material using coal powder as pore former

The aim of the study was to prepare a porous sound-absorbing material using steel slag and fly ash as the main raw material, with coal powder and sodium silicate used as a pore former and binder respectively. The influence of the experimental conditions such as the ratio of fly ash, sintering temperature, sintering time, and porosity regulation on the performance of the porous sound-absorbing material was investigated. The results showed that the specimens prepared by this method had high sound absorption performance and good mechanical properties, and the noise reduction coefficient and compressive strength could reach 0.50 and 6.5 MPa, respectively. The compressive strength increased when the dosage of fly ash and sintering temperature were raised. The noise reduction coefficient decreased with increasing ratio of fly ash and reducing pore former, and first increased and then decreased with the increase of sintering temperature and time. The optimum preparation conditions for the porous sound-absorbing material were a proportion of fly ash of 50%（wt.%）, percentage of coal powder of 30%（wt.%）, sintering temperature of 1130°C,and sintering time of 6.0 hr, which were determined by analyzing the properties of the sound-absorbing material.