Pulsed Eddy Current Non-destructive Testing and Evaluation:A Review

Pulsed eddy current （PEC） non-destructive test- ing and evaluation （NDT＆E） has been around for some time and it is still attracting extensive attention from researchers around the globe, which can be witnessed through the reports reviewed in this paper. Thanks to its richness of spectral components, various applications of this technique have been proposed and reported in the lit- erature covering both structural integrity inspection and material characterization in various industrial sectors. To support its development and for better understanding of the phenomena around the transient induced eddy currents, attempts for its modelling both analytically and numeri- cally have been made by researchers around the world. This review is an attempt to capture the state-of-the-art development and applications of PEC, especially in the last 15 years and it is not intended to be exhaustive. Future challenges and opportunities for PEC NDT＆E are also presented.

Non-destructive experimental testing and modeling of electrical impedance behavior of untreated and treated ultra-soft clayey soils

The characterization of ultra-soft clayey soil exhibits extreme challenges due to low shear strength of such material.Hence,inspecting the non-destructive electrical impedance behavior of untreated and treated ultra-soft clayey soils gains more attention.Both shear strength and electrical impedance were measured experimentally for both untreated and treated ultra-soft clayey soils.The shear strength of untreated ultra-soft clayey soil reached 0.17 kPa for 10% bentonite content,while the shear strengths increased to 0.27 kPa and 6.7 kPa for 10% bentonite content treated with 2% lime and 10% polymer,respectively.The electrical impedance of the ultra-soft clayey soil has shown a significant decrease from 1.6 kΩ to 0.607 kΩ when the bentonite content increased from 2% to 10% at a frequency of 300 kHz.The10%lime and 10% polymer treatments have decreased the electrical impedances of ultra-soft clayey soil with 10%bentonite from 0.607 kΩ to 0.12 kΩ and 0.176 kΩ,respectively,at a frequency of 300 kHz.A new mathematical model has been accordingly proposed to model the non-destructive electrical impedancefrequency relationship for both untreated and treated ultra-soft clayey soils.The new model has shown a good agreement with experimental data with coefficient of determination（R;）up to 0.99 and root mean square error（RMSE） of 0.007 kΩ.

Optical generation,detection and non-destructive testing applications of terahertz waves

Optoelectronic terahertz generation and detection play a key role in the applications of non-destructive testing,which involves different areas such as physics,biological,material science,imaging,explosions detection,astronomy applications,semiconductor technology and superconductiong electronics. In this article,we present a reviewof the principle and performance of typical terahertz sources,detectors and non-destructive testing applications. On this basis,the newdevelopment and trends of terahertz radiation detectors are also discussed.

Application Research of the Non-Destructive Testing Using Optical Fiber Sensor

In this paper, an optical fiber sensor is designed by using optical Faraday effect. It is composed of fiber collimator, polarizer, magneto-optical crystal and mirror. Based on the magnetic flux leakage (MFL) theory, The optical fiber sensor was placed between two permanent magnets with the N-pole. Therefore, the optical fiber sensing system was built to detect the defective ferromagnetic objects. Theoretical and experimental studies shown that the system can identify a little defects, such as irons’ blind hole (diameter φ =?3mm , depth t = 4mm?), irons’ grooves (length l= 30mm , width?ω = 10mm ), hole (φ?=?3mm ) and crackle etc. The system has the characteristics of small size, high sensitivity, fast signal response and high resolution. In terms of the defective oil and gas pipelines detection, The optical fiber sensing system is used in non-destructive testing, which will be valuable and meaningful.

The Research Progress of Nondestructive Testing Technology in the Detection of Egg Quality

[Objective]The aim was to improve the quality of the egg in favour of producers and business operators according to the market demand to take scientific feeding and management.[Methods]This paper discussed the research progress of using machine vision,optical properties,and acoustic resonance technology in the egg quality nondestructive testing. [Results]Egg quality indicators directly affect their edible quality and quality levels. [Conclusion]Egg quality test has practical value and practical significance.

Nondestructive Testing Electrical Methods for Sensing Damages in Cement Mortar Beams

This paper discusses the experimental results of concurrently measured Electrical and Acoustic Emissions in order to evaluate the mechanical health status of cement mortar beams subjected to three-point bending mechanical tests. In particular, the Electrical Resistance and the Electrical Current emissions are recorded concurrent with Acoustic Emissions and the experimental results are discussed under the concept of crack initiation and propagation processes. For the first time, the electrodes that are used for conducting the measurements are placed in the bulk of the specimen, near the tensile zone, during its preparation. The damage evolution is examined by monitoring the fractional change of the Electrical Resistance and the variation of the Electrical Current in combination with the Acoustic Emission recordings.

Non-Destructive Testing of Rods Using a Potential Component of a Magnetic Field

An essentially new method for non-destructive testing of elastic electrically conductive rods using non-vortex electromagnetic induction is proved theoretically. An experimental technique for defining a location of a cross crack is offered.

Stiffness Degradation Characteristics Destructive Testing and Finite-Element Analysis of Prestressed Concrete T-Beam

The failure behavior of the precast prestressed concrete T girder was investigated by destructive test and finite-element analysis,and the mid-span deflection,girder stiffness and the variation of the cross section strain in the loading process were obtained,and the mechanical properties,mechanical behavior,elastic and plastic behavior and ultimate bearing capacity of T girder with large span were revealed.Furthermore,the relationship between the beam stiffness degradation,the neutral axis in cross-section,steel yielding and concrete cracking are investigated and analyzed.A method was proposed to predict the residual bearing capacity of a bridge based on the variation of the position of the cross section strain distribution and the section neutral axis,which provided a theoretical basis for predicting the stiffness detection and carrying capacity assessment of prestressed concrete beam.

Non-destructive Evaluation of Composite Pressure Vessel by Using FBG Sensors

In recent years, advanced composite structures are used extensively in many industries such as aerospace, aircraft, automobile, pipeline and civil engineering. Reliability and safety are crucial requirements posed by them to the advanced composite structures be- cause of their harsh working conditions. Therefore, as a very important measure, structural health monitoring （SHM） in-service is deft- nitely demanded for ensuring their safe working in-situ. In this paper, fiber Bragg grating （FBG） sensors are surface-mounted on the hoop and in the axial directions of a FRP pressure vessel to monitor the strain status during its pressurization. The experimental results show that the FBG sensors could be used to monitor the strain development and determine the ultimate failure strain of the composite pressure vessel.

NON-DESTRUCTIVE PAVEMENT LAYER THICKNESS MEASUREMENT USING EMPIRICAL MODE DECOMPOSITION WITH GPR

Ground Penetrating Radar(GPR) is an effective Non-Destructive Testing(NDT) technique for highway pavement surveys, which is able to acquire continuous pavement data compared with traditional core drilling method. In this study, we proposed an accurate and efficient method to estimate the thickness of each pavement layer using an air-coupled GPR system. For this work, the main difficulties are estimating each pavement layer's time delay and dielectric constant. We first give the basic signal model for pavement evaluation, and then present an Intrinsic Mode Functions(IMFs) product detector to determine each pavement layer's time delay. This method is based on Empirical Mode Decomposition(EMD), which is an adaptive signal decomposition procedure and proved to be suitable for suppressing noises in GPR signal. The dielectric constant was determined by metal reflection measurement. The laboratory and highway experiments illustrate that the proposed thickness estimation method yields reasonable result, thus meets the requirements of practical highway pavement survey with massive GPR data.

Non-Destructive Imaging of Water Permeation through Cementitious Materials Using MRI

In this study, water permeation through cementitious materials was observed using magnetic resonance imaging (MRI). The influence of cement type on the magnetic resonance signal was studied subsequent to determining the parameters required for imaging. Consequently, adequate imaging of water permeating through hardened cement paste (HCP) made with white Portland cement was achieved, while water permeation through ordinary Portland cement-based HCP yielded poor signal. HCPs maintained at various levels of relative humidity (RH) were observed, and the signal was detected only from those maintained at an RH of higher than 85%. The water permeation depths in HCP were observed by using MRI, and the measured depths were compared to those measured via a spraying water detector on the split surface of the specimens. As a result, good agreement was confirmed between the two methods. Additionally, MRI was applied to concrete specimens;although it was found that water was not detected when a lightweight aggregate was used, water permeation through concrete with limestone aggregate was detectable via MRI. MRI will help in understanding how water permeation causes and accelerates concrete deteriorations such as rebar corrosion and freezing and thawing.

Piezoelectric Actuator/Sensor Wave Propagation Based Nondestructive Active Monitoring Method of Concrete Structures

In order to monitor the basic mechanical properties and interior damage of concrete structures,the piezoelectric actuator/sensor based wave propagation method was investigated experimentally in the laboratory using a specifically designed test setup.The energy attenuation of stress waves was measured by the relative index between the output voltage of sensors and the excitation voltage at the actuator.Based on the experimental results of concrete cube and cylinder specimens,the effect of excitation frequencies,excitation amplitude,wave propagation paths and the curing age on the output signals of sensors are evaluated.The results show that the relative voltage attenuation coefficient RVAC is an effective indicator for measuring the attenuation of stress waves through the interior of concrete.

Multiple Objective Test Design for Accelerated Destructive Degradation Tests

Accelerated destructive degradation tests(ADDTs)are powerful to provide reliability information in the degradation processes with destructive measurements.In order to carry out an ADDT efficiently,both the estimation precision of parameters and the test cost should be considered.On the basis of the given degradation model and failure criterion,a multiple-objective optimization model for the design of ADDTs is proposed.Under constrains of the maximum measurement time,the total sample size and the number of stress levels,a comprehensive target function is suggested to reflect both the precision of lifetime estimation and total cost,and the optimal test plan is obtained,which is composed by optimal choices for samples size,measurement frequency,and the number of measurements at each stress level.A real example is illustrated to demonstrate the implementation of the proposed approach.

Rapid and Non-destructive Prediction of Protein Content in Peanut Varieties Using Near-infrared Hyperspectral Imaging Method

This study was undertaken to investigate the feasibility of near-infrared(NIR) hyperspectral imaging(1 000–2 500 nm) for non-destructive and quantitative prediction of protein content in peanut kernels. Partial least squares regression(PLSR) calibration model was established between the spectral data extracted from the hyperspectral images and the reference measured protein content values, with the coefficient of determination of prediction(R_P^2) of 0.885 and root mean square error of prediction(RMSEP) of 0.465%.Regression coefficients(RC) from PLSR analysis were used to identify the most essential wavelengths that had the greatest influence on changes in the protein content. Eight optimal wavelengths were selected by RC and its corresponding simplified RC-PLSR prediction model was also obtained, showing better performance with a higher R_P^2 of 0.870 and a lower RMSEP of 0.494%. The results indicate that hyperspectral imaging with PLSR analysis can be used as a rapid and non-destructive method for predicting protein content in peanut.

Biomarker Testing Rates in Patients with Advanced Non-Small Cell Lung Cancer Treated in the Community

Introduction: Over the past few years, molecular targeted therapies have been?emerging for the treatment of metastatic non-small cell lung cancer (NSCLC).?Targeted therapy is associated with improved outcomes in patients with identified gene alterations, and national guidelines recommend routine biomarker testing. This study evaluated real-world rates of documented epidermal growth factor receptor (EGFR) mutation and other biomarker testing in patients with advanced NSCLC over time.?Methods: Adult patients with Stage IV NSCLC were identified between January 1, 2012 and May 31, 2017 from the US Oncology Network iKnowMedTM?electronic health records. Patients were examined overall and by histology. Rates of documented EGFR mutation and other biomarker testing were calculated. Multivariable regression analyses were conducted to identify characteristics associated with documented biomarker testing. Results: A total of 14,461 patients were identified: median age was 69.3 years, 52.3% were male, 14.6% were nonsmokers, and 64.7% had non-squamous histology.?EGFR mutation testing rates were 35.5%?overall, with an increase in rates seen over time: 30.0% in 2012 to 44.0% in 2016?(p??0.001).?Anaplastic lymphoma kinase (ALK), c-ros oncogene 1 (ROS1), and programmed death-ligand 1 (PD-L1) mutation testing rates were 32.9%, 5.7%, and 5.7%, respectively. More recent diagnosis year, non-squamous histology, larger practice size, and nonsmoking status were strongly associated with higher documented EGFR and ALK mutation testing rates.?Conclusions: EGFR mutation testing rates steadily increased over time, but remained less than 50%, with lower mutation testing rates reported for ALK, ROS1, and PD-L1, suggesting that opportunities exist to improve education on testing for biomarkers in NSCLC.

Non-destructive study of fruits using grating-based X-ray imaging

Grating-based X-ray imaging can make use of conventional tube sources to provide absorption, refraction and scattering contrast images from a single set of projection images efficiently. In this paper, a fresh cherry tomato and a dried umeboshi are imaged by using X-ray Talbot–Lau interferometer. The seed distribution in the scattering image of the cherry tomato, and the wrinkles of epicarp in the refraction image of the umeboshi, are shown distinctly. The refraction and scattering images provide more information on subtle features than the absorption image. Also, the contrast-to-noise ratio values show distinguishing capacity of the three kinds of imaging techniques. The results confirm that grating-based X-ray imaging is of great potential in non-destructive fruit testing.

Determination of Bonding Failures in Transparent Materials with Non-Destructive Methods—Evaluation of Climatically Stressed Glued and Laminated Glass Compounds

As part of an international research project—funded by the European Union—capillary glasses for facades are being developed exploiting storage energy by means of fluids flowing through the capillaries. To meet highest visual demands, acrylate adhesives and EVA films are tested as possible bonding materials for the glass setup. Especially non-destructive methods (visual analysis, analysis of birefringent properties and computed tomographic data) are applied to evaluate failure patterns as well as the long-term behavior considering climatic influences. The experimental investigations are presented after different loading periods, providing information of failure developments. In addition, detailed information and scientific findings on the application of computed tomographic analyses are presented.