Experimental Study on Gas Flow Uniformity in a Diesel Particulate Filter Carrier

A Diesel Particulate Filter(DPF)is a critical device for diesel engine exhaust products treatment.When using active-regeneration purification methods,on the one hand,a spatially irregular gas flow can produce relatively high local temperatures,potentially resulting in damage to the carrier;On the other hand,the internal temperature field can also undergo significant changes contributing to increase this risk.This study explores the gas flow uniformity in a DPF carrier and the related temperature behavior under drop-to-idle(DTI)condition by means of bench tests.It is shown that the considered silicon carbide carrier exhibits good flow uniformity,with a temperature deviation of no more than 2%with respect to the same radius measurement point at the outlet during the regeneration stage.In the DTI test,the temperature is relatively high within r/2 near the outlet end,where the maximum temperature peak occurs,and the maximum radial temperature gradient is located between r/2 and the edge.Both these quantities grow as the soot load increases,thereby making the risk of carrier burnout greater.Finally,it is shown that the soot load limit of the silicon carbide DPF can be extended to 11 g/L,which reduces the frequency of active regeneration by approximately 40%compared to a cordierite DPF.

Non-Darcy Flow in Molding Sands

Darcy’s law is widely used to describe the flow in porous media in which there is a linear relationship between fluid velocity and pressure gradient. However, it has been found that for high numbers of Reynolds this law ceases to be valid. In this work, the Ergun equation is employed to consider the non-linearity of air velocity with the pressure gradient in casting sands. The contribution of non-linearity to the total flow in terms of a variable defined as a non-Darcy flow fraction is numerically quantified. In addition, the influence of the shape factor of the sand grains on the non-linear flow fraction is analyzed. It is found that for values of the Reynolds number less or equal than 1, the contribution of non-linearity for spherical particles is around 1.15%.

Uncertainty Analysis of the Residual Strength of Non-Uniformly Loaded Casingsin Deep Wells

An uncertainty analysis method is proposed for the assessment of the residual strength of a casing subjected to wear and non-uniform load in a deep well.The influence of casing residual stress,out-of-roundness and non-uniform load is considered.The distribution of multi-source parameters related to the residual anti extrusion strength and residual anti internal pressure strength of the casing after wear are determined using the probability theory.Considering the technical casing of X101 well in Xinjiang Oilfield as an example,it is shown that the randomness of casing wear depth,formation elastic modulus and formation Poisson’s ratio are the main factors that affect the uncertainty of residual strength.The wider the confidence interval is,the greater the uncertainty range is.Compared with the calculations resulting from the proposed uncertainty analysis method,the residual strength obtained by means of traditional single value calculation method is either larger or smaller,which leads to the conclusion that the residual strength should be considered in terms of a range of probabilities rather than a single value.

Heat transfer in boundary layer stagnation-point flow towards a shrinking sheet with non-uniform heat flux

In this paper, the effect of non-uniform heat flux on heat transfer in boundary layer stagnation-point flow over a shrinking sheet is studied. The variable boundary heat fluxes are considered of two types： direct power-law variation with the distance along the sheet and inverse power-law variation with the distance. The governing partial differential equations （PDEs） are transformed into non linear self-similar ordinary differential equations （ODEs） by similarity transformations, and then those are solved using very efficient shooting method. The direct variation and inverse variation of heat flux along the sheet have completely different effects on the temperature distribution. Moreover, the heat transfer characteristics in the presence of non-uniform heat flux for several values of physical parameters are also found to be interesting.

EXISTENCE OF THE UNIFORM TRAJECTORY ATTRACTOR FOR A 3D INCOMPRESSIBLE NON-NEWTONIAN FLUID FLOW

This paper studies the trajectory asymptotic behavior of a non-autonomous in- compressible non-Newtonian fluid in 3D bounded domains. In appropriate topologies, the authors prove the existence of the uniform trajectory attractor for the translation semigroup acting on the united trajectory space.

Numerical Prediction of Marine Propeller Noise in Non-Uniform Inflow

A numerical study on the acoustic radiation of a propeller interacting with non-uniform inflow has been conducted. Real geometry of a marine propeller DTMB 4118 is used in the calculation, and sliding mesh technique is adopted to deal with the rotational motion of the propeller. The performance of the DES （Detached Eddy Simulation） approach at capturing the unsteady forces and moments on the propeller is compared with experiment. Far-field sound radiation is predicted by the formation 1A developed by Farassat, an integral solution of FW-H （Ffowcs Williams-Hawkings） equation in time domain. The sound pressure and directivity patterns of the propeller operating in two specific velocity distributions are discussed.

A Computer Method of Steady Non-Uniform Gradually Varied Flow in Open Channel & in River

Most of water flow in open channel or in river belongs to steady non-uniform flow. The surface profiles are caused by changes of channel section. It is very important to analyze its computation. According to the regularity of its surface change, the suitable sectional dimensions of open channel or flood control work can be designed. Commonly, computation of non-uniform flow adopts the traditional methods by hand or by graphic method. The speed and precision of computation are restricted. In this paper, a software to calculate water surface profile is introduced. The software is put forward by using C++ .By means of interpolate method and dialogue between user and computer, we can calculate the water surface profile much more quickly and exactly.

Boundary Layer Flow of an Unsteady Dusty Fluid and Heat Transfer Over a Stretching Sheet with Non-Uniform Heat Source/Sink

An analysis has been carried out to study the effect of hydrodynamic laminar boundary layer flow and heat transfer of a dusty fluid over an unsteady stretching surface in the presence of non-uniform heat source/sink. Heat transfer characteristics are examined for two different kinds of boundary conditions, namely 1) variable wall temperature and 2) variable heat flux. The governing partial differential equations are transformed to system of ordinary differential equations. These equations are solved numerically by applying RKF-45 method. The effects of various physical parameters such as magnetic parameter, dust interaction parameter, number density, Prandtl number, Eckert number, heat source/sink parameter and unsteadiness parameter on velocity and temperature profiles are studied.

Non-uniform slot suction/injection into mixed convection boundary layer flow over vertical cone

The aim of this work is to study the effect of non-uniform single and double slot suction/injection into a steady mixed convection boundary layer flow over a vertical cone, while the axis of the cone is inline with the flow. The governing boundary layer equations are transformed into a non-dimensional form by a group of non-similar trans- formations. The resulting coupled non-linear partial differential equations are solved nu- merically by employing the quasi-linearization technique and an implicit finite-difference scheme. Numerical computations are performed for different values of the dimensionless parameters to display the velocity and temperature profiles graphically. Also, numerical results are presented for the skin friction and heat transfer coefficients. Results indicate that the skin friction and heat transfer coefficients increase with non-uniform slot suction, but the effect of non-uniform slot injection is just opposite.

NON-STATIONARY EFFECTS IN HYPERSONIC NONUNIFORM DUSTY-GAS FLOW PAST A BLUNT BODY

In the framework of the two-fluid model, a hypersonic flow of a nonuniform dusty gas with low inertial (non-depositing) particles around a blunt body is considered. The particle mass concentration is assumed to be small, so that the effect of particles on the carrier phase is significant only inside the boundary layer where the particles accumulate. Stepshaped and harmonic nonuniformities of the particle concentration ahead of the bow shock wave are considered and the corresponding nonstationary distributions of the particle concentration in the shock layer are studied. On the basis of numerical study of nonstationary two-phase boundary layer equations derived by the matched asymptotic expansion method, the effects of free-stream particle concentration nonuniformities on the thermal flux, and the friction coefficient in the neighborhood of stagnation point are investigated, in particular, the most “dangerous” nonuniformity periods are found.

Strongly nonlinear long interfacial waves in uniform basic flows and their dispersion relationship

In this paper, long interfacial waves of finite amplitude in uniform basic flows are considered with the assumption that the aspect ratio between wavelength and water depth is small. A new model is derived using the velocities at arbitrary distances from the still water level as the velocity variables instead of the commonly used depth-averaged velocities. This significantly improves the dispersion properties and makes them applicable to a wider range of water depths. Since its derivation requires no assumption on wave amplitude, the model thus can be used to describe waves with arbitrary amplitude.

Unsteady Non-Uniform Flow of Molten Metals in Rectangular Open Channels

In the metallurgical industries, it is very important to characterize the flow of molten metals in open channels given that they are transported through these devices to different plant sections. However, unlike the flow of water which has been studied since ancient times, the flow of molten metals in open channels has received little attention. The unsteady non-uniform flow of blast furnace molten pig iron in a rectangular open channel is analyzed in this work by numerical solution of the Saint-Venant equations. The influence of mesh size on the convergence of molten metal height is studied to determine the proper mesh and time step sizes. A sinusoidal inflow pulse is imposed at the entrance of the channel in order to analyze the propagation of the resulting wave. The influence of the angle of inclination of the channel and the roughness coefficient of the walls on the amplitude and the dynamic behavior of the height of the molten metal are analyzed. Phase portraits of the channel state variables are constructed and interpreted. Numerical simulations show that as the angle of inclination of the channel increases, the amplitude of the formed wave decreases. From 10 degrees onwards, the peak of the wave descends even below the initial height. On the other hand, the roughness coefficient affects the molten pig iron height profiles in an inverse way than the angle of inclination. The amplitude of the formed wave increases as the roughness coefficient increases.

Image Non-Uniformity Correction in 3T Gd-EOB-DTPA-Enhanced Magnetic Resonance Imaging: Comparison among Different Software Versions

Background: Non-uniformity in signal intensity occurs commonly in magnetic resonance (MR) imaging, which may pose substantial problems when using a 3T scanner. Therefore, image non-uniformity correction is usually applied. Purpose: To compare the correction effects of the phased-array uniformity enhancement (PURE), a calibration-based image non-uniformity correction method, among three different software versions in 3T Gd-EOB-DTPA-enhanced MR imaging. Material and Methods: Hepatobiliary-phase images of a total of 120 patients who underwent Gd-EOB-DTPA-enhanced MR imaging on the same 3T scanner were analyzed retrospectively. Forty patients each were examined using three software versions (DV25, DV25.1, and DV26). The effects of PURE were compared by visual assessment, histogram analysis of liver signal intensity, evaluation of the spatial distribution of correction effects, and evaluation of quantitative indices of liver parenchymal enhancement. Results: The visual assessment indicated the highest uniformity of PURE-corrected images for DV26, followed by DV25 and DV25.1. Histogram analysis of corrected images demonstrated significantly larger variations in liver signal for DV25.1 than for the other two versions. Although PURE caused a relative increase in pixel values for central and lateral regions, such effects were weaker for DV25.1 than for the other two versions. In the evaluation of quantitative indices of liver parenchymal enhancement, the liver-to-muscle ratio (LMR) was significantly higher for the corrected images than for the uncorrected images, but the liver-to-spleen ratio (LSR) showed no significant differences. For corrected images, the LMR was significantly higher for DV25 and DV26 than for DV25.1, but the LSR showed no significant differences among the three versions. Conclusion: There were differences in the effects of PURE among the three software versions in 3T Gd-EOB-DTPA-enhanced MR imaging. Even if the non-uniformity correction method has the same brand name, correction effects may differ depending on the software version, and these differences may affect visual and quantitative evaluations.

Unsteady mixed convection flow over stretching sheet in presence of chemical reaction and heat generation or absorption with non-uniform slot suction or injection

The article examines the unsteady mixed convection flow over a vertical stretching sheet in the presence of chemical reaction and heat generation or absorption with non-uniform mass transfer. The unsteadiness is caused by the time dependent free stream velocity varying arbitrarily with time. Non-similar solutions are obtained nu- merically by solving the coupled nonlinear partial differential equations using the quasi- linearization technique in combination with an implicit finite difference scheme. To reveal the tendency of the solutions, typical results for the local skin friction coefficient and the local Nusselt and Sherwood numbers are presented for different values of parameters. The effects of various parameters on the velocity, temperature, and concentration distributions are discussed here. The present numerical results are compared with the previously published work, and the results are found to be in excellent agreement.

Novel wavelet-homotopy Galerkin technique for analysis of lid-driven cavity flow and heat transfer with non-uniform boundary conditions

In this paper, a brand-new wavelet-homotopy Galerkin technique is developed to solve nonlinear ordinary or partial differential equations. Before this investigation,few studies have been done for handling nonlinear problems with non-uniform boundary conditions by means of the wavelet Galerkin technique, especially in the field of fluid mechanics and heat transfer. The lid-driven cavity flow and heat transfer are illustrated as a typical example to verify the validity and correctness of this proposed technique. The cavity is subject to the upper and lower walls’ motions in the same or opposite directions.The inclined angle of the square cavity is from 0 to π/2. Four different modes including uniform, linear, exponential, and sinusoidal heating are considered on the top and bottom walls, respectively, while the left and right walls are thermally isolated and stationary.A parametric analysis of heating distribution between upper and lower walls including the amplitude ratio from 0 to 1 and the phase deviation from 0 to 2π is conducted. The governing equations are non-dimensionalized in terms of the stream function-vorticity formulation and the temperature distribution function and then solved analytically subject to various boundary conditions. Comparisons with previous publications are given,showing high efficiency and great feasibility of the proposed technique.

CADFlow在无创血流动力学评估中的探索

目的探究CADFlow(Cardiac Auto-Doppler Flow)与颈动脉超声、经胸超声心动图两种检查结果的相关性,为进一步临床推广应用奠定基础。方法217例健康志愿者纳入本研究,分别用颈动脉超声、CADFlow收集受试者双侧颈动脉的峰值速度(Vmax),最低速度(Vmin);用经胸超声心动图、CADFlow收集受试者心排血量(CO)。结果两种方法测得健康人群的CO结果无显著性差异(P>0.05)。两种方法测得Vmax及Vmin无显著性差异(P>0.05),但女性较男性偏低并随年龄增加逐渐下降,两组间有显著性差异(P<0.05)。各种方法测得CO、Vmax、Vmin结果高度相关(r值均大于0.8,P<0.05)。结论CADFlow血流监测技术除与常规超声检测结果具有良好相关性外,CO、Vmax、Vmin均随年龄变化而变化,且该变化可以被CADFlow血流监测技术准确检测。

Research on a non-linear chaotic prediction model for urban traffic flow

In order to solve serious urban transport problems, according to the proved chaotic characteristic of traffic flow, a non linear chaotic model to analyze the time series of traffic flow is proposed. This model reconstructs the time series of traffic flow in the phase space firstly, and the correlative information in the traffic flow is extracted richly, on the basis of it, a predicted equation for the reconstructed information is established by using chaotic theory, and for the purpose of obtaining the optimal predicted results, recognition and optimization to the model parameters are done by using genetic algorithm. Practical prediction research of urban traffic flow shows that this model has famous predicted precision, and it can provide exact reference for urban traffic programming and control.

Gas Condensate Two Phase Flow Performance in Porous Media Considering Capillary Number and Non-Darcy Effects

Retrograde condensation frequently occurs during the development of gas condensate reservoirs. The loss of productivity is often observed due to the reduced relative permeability to gas as condensate accumulates near the well bore region. How to describe the condensate blockage effect exactly has been a continuous research topic. However, up to now, the present methods usually over-estimate or underestimate the productivity reduction due to an incorrect understanding of the mechanism of flow in porous medium, which inevitably results in an inaccurate prediction of production performance. It has been found in recent numerous theoretical and experimental studies that capillary number and non-Darcy flow have significant influence on relative permeability in regions near the well bore. The two effects impose opposite impacts on production performance, thus leading to gas condensate flow showing characteristics different from general understanding. It is significant for prediction of performance in gas condensate wells to understand the two effects exactly. The aim of the paper is to describe and analyze the flow dynamics in porous media accurately during the production of gas condensate reservoirs. Based on the description of three-zone flow mechanism, capillary number and non-Darcy effect are incorporated in the analysis of relative permeability, making it possible to describe the effect of condensate blockage. The effect of capillary number and inertial flow on gas and condensate relative permeability is analyzed in detail. Novel Inflow Performance Relation (IPR) models considering high velocity effects are formulated and the contrast analysis of different IPR models is conducted. The result shows that the proposed method can help predict the production performance and productivity more accurately than conventional methods.

Combined Action of Uniform Flow and Oscillating Flow Around Marine Riser at Low Keulegan-Carpenter Number

With the increase of petroleum and gas production in deep ocean, marine risers of circular cylinder shape are widely used in the offshore oil and gas platform. In order to research the hydrodynamic performance of marine risers, the dynamic mesh technique and User-Defined Function(UDF) are used to simulate the circular cylinder motion. The motion of a transversely oscillating circular cylinder in combination of uniform flow and oscillating flow is simulated. The uniform flow and oscillating flow both are in x direction. SIMPLE algorithm is used to solve the Navier-Stokes equations. The User-Defined Function is used to control the cylinder transverse vibration and the inlet flow. The lift and drag coefficient changing with time and the map of vorticity isolines at different phase angle are obtained. Force time histories are shown for uniform flow at Reynolds number(Re) of 200 and for the combination of uniform and oscillating flows. With the increase of amplitude of oscillating flow in combined flow, the change of lift amplitude is not sensitive to the the change of cylinder oscillating frequency. Lift amplitude increases with the increase of oscillating flow amplitude in the combined flow, but there is no definite periodicity of the lift coefficient. The drag and inertia force coefficients change when the maximum velocity of the oscillating flow increases in the combined flow. The vortex shedding near the circular cylinder shows different characteristics.

Uniformity evaluation and optimization of fluid flow characteristics in a seven-strand tundish

The effect of flow control devices（FCDs） on the uniformity of flow characteristics in a seven-strand symmetrical trapezoidal tundish was studied using both an experimental 1：2.5 hydraulic model and a numerical simulation of a 1：1 geometric model.The variation coefficient（CV） was defined to evaluate the flow uniformity of the seven-strand tundish.An optimized FCD configuration was proposed on the basis of the evaluation of experimental results.It is concluded that a turbulence inhibitor（TI） and U-type dam are essential to improve the uniformity of fluid flow in the seven-strand tundish.In addition,the configuration of inclination T-type dams with a height of 200 mm between the second and third strands and with a height of 300 mm between the third and fourth strands can minimize the proportion of dead zone.After optimizing the configuration of FCDs,the variation coefficient reduces below 20%of the mean value,and the average proportion of dead zone is just 14.6%;in addition,the temperature fluctuation between the strands could be controlled within 0.6 K.In summary,the uniformity of flow and temperature in the seven-strand tundish is greatly improved.