Effect of matrix thermal properties on laser-induced plasma

The matrix thermal properties have an important impact on laser-induced plasma,as the thermal effect dominates the interaction between ns-pulsed laser and matter,especially in metals.We used a series of pure metals and aluminum alloys to measure plasma temperature and electron density through laser-induced breakdown spectroscopy,in order to investigate the effect of matrix thermal properties on laser-induced plasma.In pure metals,a significant negative linear correlation was observed between the matrix thermal storage coefficient and plasma temperature,while a weak correlation was observed with electron density.The results indicate that metals with low thermal conductivity or specific heat capacity require less laser energy for thermal diffusion or melting and evaporation,resulting in higher ablation rates and higher plasma temperatures.However,considering ionization energy,thermal effects may be a secondary factor affecting electron density.The experiment of aluminum alloy further confirms the influence of thermal conductivity on plasma temperature and its mechanism explanation.

Effects of Diamond on the Mechanical Properties and Thermal Conductivity of Si_(3)N_(4)Composites Fabricated Using Spark Plasma Sintering

Micrometer-sized diamonds were incorporated into silicon nitride(Si_(3)N_(4))matrix to manufacture high-performance Si_(3)N_(4)-based composites using spark plasma sintering at 1500℃under 50 MPa.The effects of the diamond content on the phase composition,microstructure,mechanical properties and thermal conductivity of the composites were investigated.The results showed that the addition of diamond could effectively improve the hardness of the material.The thermal conductivity of Si_(3)N_(4)increased to 52.97 W/m·k at the maximum with the addition of 15 wt%diamond,which was 27.5%higher than that of the monolithic Si_(3)N_(4).At this point,the fracture toughness was 7.54 MPa·m^(1/2).Due to the addition of diamond,the composite material generated a new substance,MgSiN2,which effectively combined Si_(3)N_(4)with diamond.MgSiN2 might improve the hardness and thermal conductivity of the materials.

Simultaneous removal of NO and SO_2 from dry gas stream using non-thermal plasma

In order to investigate the feasibility of sequential removal NO and SO2 using non-thermal plasma and adsorbent simultaneously, the removal of NO and SO2 from dry gas stream （NO/SO2/N2/O2） with very little O2 using non-thermal plasma was investigated using a coaxial dielectric barrier discharge. Comparative experiments were carried out in the dry gas stream with and without Ar respectively at O2 concentration of 0.1%. The results showed that NO could be removed remarkably and it would be enhanced in the presence of Ar in the dry gas stream. It seems that SO2 could not be removed unless there is Ar in the dry gas stream. The mechanism of removal of NO and SO2 in the dry gas stream was discussed.

Study on purification technology of polyacrylamide wastewater by non-thermal plasma

In this work, non-thermal plasma has been applied to treat polyacrylamide（PAM） wastewater.We have investigated the influence of the rule of PAM wastewater initial pH, solution concentration and discharge time, discharge voltage on chemical oxygen demand（COD）degradation rate. At the same time, the effect of pH and discharge time on the viscosity removal rate of PAM solution was also studied. Then, the effect of pH on the viscosity removal rate of1.0 gl-1 PAM solution was studied separately. Through orthogonal test, the factors affecting the COD degradation rate of PAM wastewater were determined as follows: discharge time > discharge voltage > solution concentration > wastewater initial pH. The COD highest removal rate of PAM wastewater reached 85.74%, when the optimal conditions are as follows:discharge voltage 40 k V, discharge time 5 h, solution concentration 1.0 gl-1, pH 1.5. This research provides some basic data and new theoretical basis for PAM wastewater purification.

Synergistic removal of nitrogen monoxide by non-thermal plasma and catalyst simultaneously

An experimental system of De-NO with plasma-catalyst（Cu zeolite） was established to investigate the differences between De- NO with plasma-catalyst and De-NO only with plasma, to provide the instruction for selecting appropriate catalyst and operating condition, The characteristics of De-NO with plasma and De-NO with plasma-catalyst were investigated comparatively by experiments. The experimental results show that De-NO with plasma-catalyst has high NO removal rate; Cu zeolite is an effective catalyst which can promote NO removal rate in plasma remarkably; De-NO with plasma-catalyst should be operated at low temperature and the temperature has opposite effects on the function of catalvst and plasma; water vapor and O2 can increase the NO removal rate.

Non-thermal Plasma Suppresses Bacterial Colonization on Skin Wound and Promotes Wound Healing in Mice

The present study evaluated the effect of non-thermal plasma on skin wound healing in BalB/c mice.Two 6-mm wounds along the both sides of the spine were created on the back of each mouse（n=80） by using a punch biopsy.The mice were assigned randomly into two groups,with 40 animals in each group：a non-thermal plasma group in which the mice were treated with the non-thermal plasma;a control group in which the mice were left to heal naturally.Wound healing was evaluated on postoperative days（POD） 4,7,10 and 14（n=5 per group in each POD） by percentage of wound closure.The mice was euthanized on POD 1,4,7,10,14,21,28 and 35（n=1 in each POD）.The wounds were removed,routinely fixed,paraffin-embedded,sectioned and HE-stained.A modified scoring system was used to evaluate the wounds.The results showed that acute inflammation peaked on POD 4 in non-thermal plasma group,earlier than in control group in which acute inflammation reached a peak on POD 7,and the acute inflammation scores were much lower in non-thermal group than in control group on POD 7（P0.05）.The amount of granular tissue was greater on POD 4 and 7 in non-thermal group than in control group（P0.05）.The re-epithelialization score and the neovasularization score were increased significantly in non-thermal group when compared with control group on POD 7 and 10（P0.05 for all）.The count of bacterial colonies was 103 CFU/mL on POD 4 and 20 CFU/mL on POD 7,significantly lower than that in control group（109 CFU/mL on POD 4 and 1012 CFU/mL on the POD 7）（P0.05）.It was suggested that the non-thermal plasma facilitates the wound healing by suppressing bacterial colo-nization.

Recent progress on non-thermal plasma technology for high barrier layer fabrication

This review describes the application of non-thermal plasma（NTP） technology for high barrier layer fabrication in packaging area.NTP technology is considered to be the most prospective approaches for the barrier layer fabrication over the past decades due to unpollution,high speed,low-costing.The applications of NTP technology have achieved numerous exciting results in high barrier packaging area.Now it seemly demands a detailed review to summarize the past works and direct the future developments.This review focuses on the different NTP resources applied in the high barrier area,the role of plasma surface modification on packaging film surface properties,and the deposition of different barrier coatings based on NTP technology.In particular,this review emphasizes the cutting-edge technologies of NTP on interlayer deposition with organic,inorganic for multilayer barriers fabrication.The future prospects of NTP technology in high barrier film areas are also described.

Sterilization of Staphylococcus Aureus by an Atmospheric Non-Thermal Plasma Jet

An atmospheric non-thermal plasma jet was developed for sterilizing the Staphylococcus aureus （S. aureus）. The plasma jet was generated by dielectric barrier discharge （DBD）, which was characterized by electrical and optical diagnostics. The survival curves of the bacteria showed that the plasma jet could effectively inactivate 10 6 cells of S. aureus within 120 seconds and the sterilizing efficiency depended critically on the discharge parameter of the applied voltage. It was further confirmed by scanning electron microscopy （SEM） that the cell morphology was seriously damaged by the plasma treatment. The plasma sterilization mechanism of S. aureus was attributed to the active species of OH, N 2 ＋ and O, which were generated abundantly in the plasma jet and characterized by OES. Our findings suggest a convenient and low-cost way for sterilization and inactivation of bacteria.

Synergetic effect between non-thermal plasma and photocatalytic oxidation on the degradation of gas-phase toluene: Role of ozone

In this study, a hybrid process using non‐thermal plasma (NTP) and photocatalytic oxidation (PCO) was adopted for the degradation of gas‐phase toluene using TiO2 as the photocatalyst. To discover the synergetic effect between NTP and PCO, the performances of both sole (O3, UV, NTP, and PCO) and combined (O3 + TiO2, O3 + UV, NTP + UV, O3 + PCO, and NTP + PCO) processes were investigated from different perspectives, such as the toluene removal efficiency, selectivity of COx, mineralization rate, ozone utilization, and the generation of by‐products. The toluene removal efficiency of the combined NTP + PCO process was 80.2%, which was much higher than that of a sole degradation process such as NTP (18.8%) and PCO (13.4%). The selectivity of CO2 and the ozone utilization efficiency also significantly improved. The amount of by‐products in the gas phase and the carbon‐ based intermediates adsorbed on the catalyst surface dramatically reduced. The improvement in the overall performances of the combined NTP + PCO process was mainly ascribed to the efficient utilization of ozone in the photocatalytic oxidation, and the ozone further acting as an electron acceptor and scavenger, generating more hydroxyl radicals and reducing the recombination of electron‐ hole pairs.

Study of Non-Thermal DC Arc Plasma of CH_4/Ar at Atmospheric Pressure Using Optical Emission Spectroscopy and Mass Spectrometry

Non-thermal C/H/Ar plasmas are widely applied to carbonaceous material production and processing.In this work,plasma parameters and gaseous species of the atmospheric non-thermal C/H/Ar plasmas produced by an atmospheric-pressure DC arc discharge generator in CH_4/Ar were investigated.The voltage-current characteristics were measured for different CH_4/Ar ratios.Optical emission spectroscopy was employed to analyze the electron excitation temperature,gas temperature and electron density under various discharge conditions.The hydrocarbon molecules produced in the CH4/Ar plasmas were detected with photoionization mass spectrometry.The optical spectral results demonstrated that the electron excitation temperature was 0.4-1 eV,the gas temperature was 2800-4200 K and the electron density was in the range of（5-20）×10^15 cm^-3.The mass spectrum indicated that a variety of unsaturated hydrocarbons（C2H4,C3H6,C6H6,etc.） and several highly unsaturated hydrocarbons（C4H2,C5H6,etc.） were produced in the non-thermal arc plasmas.

Mechanism and Kinetics Analysis of NO/SO_2/N_2/O_2 Dissociation Reactions in Non-Thermal Plasma

The kinetics mechanism of the dissociation reactions in a NO/SO2/N2/O2 system was investigated in consideration of energetic electrons＇ impacts on a non-thermal plasma. A model was derived from the Boltzmann equation and molecule collision theory to predict the dissociation reaction rate coefficients. Upon comparison with available literature, the model was confirmed to be acceptably accurate in general. Several reaction rate coefficients of the NO/SO2/N2/O2 dissociation system were derived according to the Arrhenius formula. The activation energies of each plasma reaction were calculated by quantum chemistry methods. The relation between the dissociation reaction rate coefficient and electron temperature was established to describe the importance of each reaction and to predict relevant processes of gaseous chemical reactions. The sensitivity of the mechanism of NO/SO2/N2/O2 dissociation reaction in a non-thermal plasma was also analysed.

Improvement of Polytetrafluoroethylene Surface Energy by Repetitive Pulse Non-Thermal Plasma Treatment in Atmospheric Air

Improvement of polytetrafluoroethylene surface energy by non-thermal plasma treatment is presented, using a nanosecond-positive-edge repetitive pulsed dielectric barrier discharge generator in atmospheric air. The electrical parameters including discharging power, peak and density of micro-discharge current were calculated, and the electron energy was estimated. Surface treatment experiments of polytetrafluoroethylene films were conducted for both different applied voltages and different treating durations. Results show that the surface energy of polytetrafluoroethylene film could be improved to 40 mJ/m2 or more by plasma treatment. Surface roughness measurement and surface X-ray photoelectron spectroscopy analysis indicate that there are chemical etching and implantation of polar oxygen groups in the sample surface treating process, resulting in the improvement of the sample surface energy. Compared with an AC source of 50 Hz, the dielectric barrier discharges generated by a repetitive pulsed source could provide higher peak power, lower mean power, larger micro-discharge current density and higher electron energy. Therefore, with the same applied peak voltage and treating duration, the improvement of polytetrafluoroethylene surface energy using repetitive pulsed plasma is more effective, and the plasma treatment process based on repetitive pulsed dielectric barrier discharges in air is thus feasible and applicable.

Efficiency of Removing Sulfur Dioxide in the Air by Non-Thermal Plasma Along with the Application of the Magnetic Field

The non-thermal plasma created by high voltage pulsed power supply can be used to remove sulfur dioxide in the air, but how to increase the removing efficiency is not clear. It is novel to apply the magnetic field in removing SO2 as discussed in this paper. The mechanisms of removing sulfur dioxide by non-thermal plasma along with the application of the magnetic field are analyzed, and the related factors affecting the removal efficiency, such as the magnitude of pulsed voltage, the polarity of the pulse, the layout of the discharge electrode, especially the magnetic field are experimentally investigated. It can be concluded that the purification efficiency is improved significantly by applying the magnetic field.

The Advantages of Non-Thermal Plasma for Detonation Initiation Compared with Spark Plug

In this paper,the characteristics of detonation combustion ignited by AC-driven non-thermal plasma and spark plug in air/acetylene mixture have been compared in a doubletube experiment system.The two tubes had the same structure,and their closed ends were installed with a plasma generator and a spark plug,respectively.The propagation characteristics of the flame were measured by pressure sensors and ion probes.The experiment results show that,compared with a spark plug,the non-thermal plasma obviously broadened the range of equivalence ratio when the detonation wave could develop successfully,it also heightened the pressure value of detonation wave.Meanwhile,the detonation wave development time and the entire flame propagation time were reduced by half.All of these advantages benefited from the larger ignition volume when a non-thermal plasma was applied.

Three-dimensional numerical simulation of heating and melting behaviors of cerium oxide powders in radio frequency thermal plasma

The present study aims at the numerical simulations of the melting process of cerium oxide particles in RF thermal plasma.The physical model and the calculating method were described firstly;the interaction between cerium oxide particles and plasma was analyzed;specific attention was given to the effects of particle initial size,injection velocity on the particle melting and trajectory in plasma.The influence of the temperature field and velocity field distribution of the plasma around the particle trajectory on the melting effect is analyzed,and the relationship between the heat absorption efficiency of the particles and the particle size reduction process is further determined.It is also found that there exists an optimal particle initial injection velocity which led to a more concentrated final particle size distribution and a more significant reduction of particle size.The results could provide effective guidance for understanding the plasma spheroidization process of uranium dioxide and cerium dioxide powder particles.

Quasi-direct numerical simulations of the flow characteristics of a thermal plasma reactor with counterflow jet

Three-dimensional quasi-direct numerical simulations have been performed to investigate a thermal plasma reactor with a counterflow jet. The effects of the momentum flux ratio and distance between the counterflow jet and the thermal plasma jet on the flow characteristics are addressed. The numerical results show that the dimensionless location of the stagnation layer is significantly affected by the momentum flux ratio, but it is not dependent on the distance.Specifically, the stagnation layer is closer to the plasma torch outlet with the increase of the momentum flux ratio. Furthermore, the flow regimes of the stagnation layer and the flow characteristics of the thermal plasma jet are closely related to the momentum flux ratio. The characteristic frequencies associated with the different regimes are identified. The deflecting oscillation flow regimes are found when the momentum flux ratio is low, which provokes axial velocity fluctuations inside the thermal plasma jet. By contrast, for cases with a high momentum flux ratio, flapping flow regimes are distinguished. The thermal plasma jets are very stable and the axial velocity fluctuations mainly exist in the stagnation layer.

Effect of Non-Thermal Plasma Modified NiAl Layered Double Hydroxides on the Removal of Fluoride from Aqueous Solution

In this paper, NiAl layered double hydroxides (NiAl-LDHs) has been modified by non-thermal plasma (NTP) to enhance the fluoride removal capacity of materials. The samples were characterized by X-ray diffraction, Fourier transform infrared spectrometer (FTIR), Thermogravimetric differential thermal analyzer (TG-DTA) and N2 adsorption-desorption. Effects of pH, co-existing anions, temperature and kinetics on F﹣ adsorption were investigated. The results showed that pH affects the adsorbent surface charge. The effective pH range for F﹣ removal was between 4.5 and 10. Lower pH potentially causes dissolution of NiAl-LDHs. The negligible interference of coexisting ions such as makes the NiAl-LDHs a promising sorbent for fluoride polluted water treatment.

Effect of high-voltage discharge non-thermal plasma on g-C_3N_4 in a plasma-photocatalyst system

The synergistic effect of high voltage discharge non‐thermal plasma(NTP)and photocatalysts on contaminant removal has repeatedly confirmed by plenty of researches.Most previous plasma‐photocatalyst synergistic systems focused on the utilization of the ultraviolet light but ignored the visible light generated by high voltage discharge.Graphitic carbon nitride(g‐C3N4),a metal‐free semiconductor that exhibits high chemical stability,can utilize both the ultraviolet and visible light from high voltage discharge.However,the synergistic system of NTP and g‐C3N4 has been researched little.In this paper,the effect of NTP generated by dielectric barrier discharge(DBD)on g‐C3N4 is studied by comparing the photocatalytic activities,the surface physical structure and the surface chemical characteristics of pristine and plasma treated g‐C3N4.Experimental results indicate that the DBD plasma can change the physical structure and the chemical characteristics and to further affect the photocatalytic activity of g‐C3N4.The effect of NTP on g‐C3N4 is associated with the discharge intensity and the discharge time.For a long time scale,the effect of NTP on g‐C3N4 photocatalysts presents a periodic change trend.

Premature failure induced by non-equilibrium grain-boundary tantalum segregation in air-plasma sprayed ZrO_(2)-YO_(1.5)-TaO_(2.5)thermal barrier coatings

ZrO_(2)-YO_(1.5)-TaO_(2.5)(ZYTO)is a promising top-coat material for thermal barrier coatings(TBCs).The bulk properties of ZYTO have been reported by several studies,but its performances as TBCs are less-well understood.In this work,ZYTO TBCs were prepared by air plasma spraying(APS)and their thermal cycling performances were investigated at 1150℃.Despite of the good bulk properties,APS ZYTO TBCs present an extremely short thermal fatigue life.This is attributed to the non-equilibrium grain-boundary segregation of TaO_(2.5) induced by limited solubility and rapid quenching during APS process,resulting in a tetragonal(t)to cubic(c)and metastable-tetragonal(tm)phase transformation in ZYTO TBCs.The volume shrinkage(~0.74vol%)of phase transformation leads to many cracks at the c/tm phase boundaries after deposition.On the other hand,the formation of cubic phase with massive grain-boundary Ta segregation induces a large intergranular embrittlement and a weak bonding strength(~5.3 MPa),resulting in the premature failure of the ZYTO TBCs.

The effects of radio frequency atmospheric pressure plasma and thermal treatment on the hydrogenation of TiO_(2) thin film

The effects of radio frequency(RF)atmospheric pressure(AP)He/H_(2)plasma and thermal treatment on the hydrogenation of TiO_(2)thin films were investigated and compared in this work.The color of the original TiO_(2)film changes from white to black after being hydrogenated in He/H_(2)plasma at160 W(gas temperature~381℃)within 5 min,while the color of the thermally treated TiO_(2)film did not change significantly even in pure H_(2)or He/H_(2)atmosphere with higher temperature(470℃)and longer time(30 min).This indicated that a more effective hydrogenation reaction happened through RF AP He/H_(2)plasma treatment than through pure H_(2)or He/H_(2)thermal treatment.The color change of TiO_(2)film was measured based on the Commission Internationale d’Eclairage L*a*b*color space system.Hydrogenated TiO_(2)film displayed improved visible light absorption with increased plasma power.The morphology of the cauliflower-like nanoparticles of the TiO_(2)film surface remained unchanged after plasma processing.X-ray photoelectron spectroscopy results showed that the contents of Ti3+species and Ti-OH bonds in the plasma-hydrogenated black TiO_(2)increased compared with those in the thermally treated TiO_(2).X-ray diffraction(XRD)patterns and Raman spectra indicated that plasma would destroy the crystal structure of the TiO_(2)surface layer,while thermal annealing would increase the overall crystallinity.The different trends of XRD and Raman spectra results suggested that plasma modification on the TiO_(2)surface layer is more drastic than on its inner layer,which was also consistent with transmission electron microscopy results.Optical emission spectra results suggest that numerous active species were generated during RF AP He/H_(2)plasma processing,while there were no peaks detected from thermal processing.A possible mechanism for the TiO_(2)hydrogenation process by plasma has been proposed.Numerous active species were generated in the bulk plasma region,accelerated in the sheath region,and bumped toward the TiO_(2)film,which will react with the TiO_(2)surface to form OVs and disordered layers.This leads to the tailoring of the band gap of black TiO_(2)and causes its light absorption to extend into the visible region.