Atomically dispersed calcium as solid strong base catalyst with high activity and stability

Solid strong base catalysts are highly attractive for diverse reactions owing to their advantages of neglectable corrosion,facile separation,and environmental friendliness.However,their widespread applications are impeded by basic components aggregation and low stability.In this work,we fabricate single calcium atoms on graphene(denoted as Ca1/G)by use of a redox strategy for the first time,producing solid strong base catalyst with high activity and stability.The precursor Ca(NO_(3))_(2)is first reduced to CaO at 400℃ by the support graphene,forming CaO/G with conventional basic sites,and the subsequent reduction at 850℃results in the generation of Ca1/G with atomically dispersed Ca.Various characterizations reveal that Ca single atoms are anchored on graphene in tetra-coordination(Ca-C_(2)-N_(2))where N is in situ doped from Ca(NO_(3))_(2).The atomically dispersed Ca,along with their anchoring on the support,endow Ca1/G with high activity and stability toward the transesterification reaction of ethylene carbonate with methanol.The turnover frequency value reaches 128.0 h^(-1)on Ca1/G,which is much higher than the traditional counterpart CaO/G and various reported solid strong bases(2.9-46.2 h^(-1)).Moreover,the activity of Ca1/G is well maintained during 5 cycles,while 60%of activity is lost for the conventional analogue CaO/G due to the leaching of Ca.

Catalytic Performance of Aquathermolysis and Viscosity Reduction of Heavy Oil over a WO_(3)/ZrO_(2) Solid Acid

Tungstated zirconia(WO_(3)/ZrO_(2))solid acid catalysts with different WO_(3) contents were prepared by a hydrothermal method and then used in the catalytic aquathermolysis of heavy oil from Xinjiang.The WO_(3)/ZrO_(2) solid acid catalyst was characterized by a range of characterization methods,including X-ray diffraction,NH3-temperature programmed desorption,and pyridine infrared spectroscopy.The WO_(3) content of the WO_(3)/ZrO_(2) catalysts had an important impact on the structure and property of the catalysts.When the WO_(3) mass fraction was 20%,it facilitated the formation of tetragonal zirconia,thereby enhancing the creation of robust acidic sites.Acidity is considered to have a strong impact on the catalytic performance of the aquathermolysis of heavy oil.When the catalyst containing 20%WO_(3) was used to catalyze the aquathermolysis of heavy oil under conditions of 14.5 MPa,340℃,and 24 h,the viscosity of heavy oil decreased from 47266 to 5398 mPa·s and the viscosity reduction rate reached 88.6%.The physicochemical properties of heavy oil before and after the aquathermolysis were analyzed using a saturates,aromatics,resins,and asphaltenes analysis,gas chromatography,elemental analysis,densimeter etc.After the aquathermolysis,the saturate and aromatic contents significantly increased from 43.3%to 48.35%and 19.47%to 21.88%,respectively,with large reductions in the content of resin and asphaltene from 28.22%to 25.06%and 5.36%to 2.03%,respectively.The sulfur and nitrogen contents,and the density of the oil were significantly decreased.These factors were likely the main reasons for promoting the viscosity reduction of heavy oil during the aquathermolysis over the WO_(3)/ZrO_(2) solid acid catalysts.

Preparation,characterization and catalytic properties of S_2O_8^(2-)/ZrO_2-CeO_2 solid superacid catalyst

A novel solid superacid catalyst S2O8^2-/ZrO2-CeO2 was prepared by a coprecipitation method and characterized by means of XRD FTIR, BET, TEM and DSC/TG analysis methods. The results indicated that incorporation of appropriate amounts of Ce into the catalyst was beneficial to the formation of sole tetragonal ZrO2 and effectively prevented from the formation of monoclinic ZrO〉 and restrained the loss of sulfated species. XRD revealed the presence of tetragonal Ce0.16Zr0.84O2phase in the case of S2O8^2-/ZrO2-CeO2 calcined above 500 ℃. Catalytic activities of S2O8^2-/ZrO2-CeO2 for the esterification of lactic acid with n-butanol was studied. The results showed that the optimum conditions were as follows： calcination temperature of the catalyst 600 ℃, n（lactic acid）：n（n-butyl alcohol）=1.0：3.0, w（S2O8^2-/ZrO2- CeO2）=12.0%, reaction temperature 145 ℃, and reaction time 2 h. The esterification efficiency of lactic acid was about 96.6%.

Preparation and Catalytic Application of Novel Water Tolerant Solid Acid Catalysts of Zirconium Sulfate/HZSM-5

Esterification of acrylic acid（AA） to produce AA esters has widespread application in the chemical industry. A series of water tolerant solid acid catalysts was prepared, and characterized by XRD, nitrogen adsorption, TGA-DTA, XPS, and ammonia adsorption FTIR. The effects of Si/Al ratio, zirconium sulfate（ZS） loading on HZSM-5 and calcination temperature on the esterification were investigated. When 20% （mass fraction） ZS is loaded on HZSM-5, the conversion of AA reaches 100%. XRD analysis indicates that ZS is highly dispersed on HZSM-5 because no crystalline structure assigned to ZS is found. Catalytic activity and hydrophobicity of ZS supported on HZSM-5 are higher compared with those of parent ZS or HZSM-5. Results show that this kind of novel catalysts is an efficient water tolerant solid acid catalyst for esterification reactions.

Simulation of biodiesel industrial production via solid base catalyst in a fixed-bed reactor

Biodiesel industrial production based on a solid base catalyst in a fixed-bed was simulated. The lab and bench scale experiments were carded out effectively, in which the kinetic model is established and it can describe the transesterification reaction well. The Antoine equation of biodiesel is regressed with the vapor-liquid data cited of literature. The non-random two liquid （NRTL） model is applied to describe the system of fatty acid methyl ester （FAME）, methanol and glycerol and parameters are obtained. The Ternary phase map is obtained from Aspen Plus via the liquid-liquid equilibrium （LLE） data. In order to describe the production in a fixed-bed performs in industrial scale after being magnified 1 000 times, the Aspen Plus simulation is employed, where two flowsheets are simulated to predict material and energy consumption. The simulation results prove that at least 350. 42 kW energy consumption can be reduced per hour to produce per ton biodiesel compared with data reported in previous references.

Preparation of solid acid catalyst SO4^2-/TiO2/γ-Al2O3 for esterification: A study on catalytic reaction mechanism and kinetics

In this work, a series of SO4^2-/TiO2/γ-Al2O3 solid acid catalysts were synthesized by impregnation method, in which nano-TiO2 was prepared by sol–gel method, and then the nano-TiO2 sol was loaded on porous γ-Al2O3 supporter through impregnation. The structure and property of catalyst were characterized by XRD, N2-BET,SEM, TEM, XPS, NH3-TPD, Pyridine-IR and FT-IR. In addition, the catalyst of chelate bidentate coordination acid center model was established. The catalytic performance test was carried out in the esterification of n-butyl alcohol with lauric acid and the catalyst showed excellent activity. The experimental results showed that the medium strength acid sites were more dominant active sites than the strong and weak acid sites for the rapid esterification reaction. Its kinetic behaviors and activation energy were studied for the esterification under the catalytic reaction condition.

A new solid acid SO_4^(2-)/TiO_2 catalyst modified with tin to synthesize 1,6-hexanediol diacrylate

A new solid acid catalyst,SO4^2-/TiO2 modified with tin,was prepared using a sol-gel method and its physicochemical properties were revealed by nitrogen adsorption-desorption,X-ray powder diffraction,scanning electron microscopy,Fourier transform infrared spectroscopy,infrared spectroscopy of adsorbed pyridine,temperature-programmed desorption of ammonia and thermal gravimetric analysis.The structure,acidity and thermal stability of the SO4^2-/TiO2-SnO2 catalyst were studied.Incorporating tin enlarged the specific surface area and decreased crystallite size of the SO4^2-/TiO2 catalyst.The total acid sites of the modified catalyst increased and Bronsted acid strength remarkably increased with increasing tin content.The decomposition temperature of sulfate radical in the modified catalyst was 100 ℃ greater and its mass loss was more than twice that of the SO4^2-/TiO2 catalyst.The SO4^2-/TiO2-SnO2 catalyst was designed to synthesize 1,6-hexanediol diacrylate by esterification of 1,6-hexanediol with crylic acid.The yield of 1,6-hexanediol diacrylate exceeded 87% under the optimal reaction conditions：crylic acid to 1,6-hexanediol molar ratio = 3.5,catalyst loading = 7%,reaction temperature = 130 ℃ and reaction time = 3 h.The modified catalyst exhibited excellent reusability and after 10 cycles the conversion of 1,6-hexanediol was above 81%.

Reaction Kinetics of Biodiesel Synthesis from Waste Oil Using a Carbon-based Solid Acid Catalyst

The kinetics of simultaneous transesterification and esterification with a carbon-based solid acid catalyst was studied.Two solid acid catalysts were prepared by the sulfonation of carbonized vegetable oil asphalt and petroleum asphalt.These catalysts were characterized on the basis of elemental analysis,acidity site concentration,the Brunauer-Emmett-Teller（BET）surface area and pore size.The kinetic parameters with the two catalysts were determined,and the reaction system can be described as a pseudo homogeneous catalyzed reaction.All the forward and reverse reactions follow second order kinetics.The calculated concentration values from the kinetic equations are in good agreement with experimental values.

Conversion of Glucose to Valuable Platform Chemicals over Graphene Solid Acid Catalyst

Biomass-derived hexose sugars, the most abundant renewable resources in the world, have potential to be the sustainable resources for production of platform chemicals. Here, con- version of glucose is investigated by using sulfonated graphene （rGO-SOaH） as solid acid catalyst in water without any organic solvent. At first, graphene functionalized with sulfonic acid groups is prepared by using Nail and propane sultone, and then it is characterized by means of XPS, FT-IR, and TEM to confirm the existence of the sulfonic acid groups. The catalytic activity of rGO-SOaH in the conversion of glucose to valuable chemicals is studied under different reaction conditions. The maximum yield of 5-hydroxymethylfurfural （HMF） is 28.8%, and the total yield of formic acid, lactic acid and HMF is 51.94% when the reaction is conducted at the optimized reaction condition. In addition, the rGO-SOaH gives a rela- tively high total yield of the three kinds of products after five run experiments, indicating that the catalyst shows good thermal stability.

Synthesis of dimethyl carbonate by gas-phase oxidative carbonylation of methanol in the presence of solid catalyst I. Catalyst preparation and catalytic Properties

The gas-phase synthesis of dimethyl carbonate (DMC) from methanol, carbon monoxide and oXygen has here Studied in a flow system at atomspheric Pressure. A series of Catalyst used in this reaCtion have been prepared and evaluated. The influence of trivared carbon supporters, alkaline metal Promoters and operation conditions on DMC opthesis reaction has been discussed. Under the conditions of 130℃, CO/O2=1 .96, SV=3340h-1, the space-time yield (STY) of DMC over PdCl2-CuCl2-CH3COOK/ac. catalyst is 217g/l-cat h,which is higher than what is published in the literatUre so far.

Clean Aerobic Liquid Oxidation of Aldehydes with Solid Catalyst

Clean liquid oxidation of aldehydes can be accomplished using solid catalyst in the presence of molecular oxygen at room temperature, which is a valuable alternative to traditional counterparts.

One Step Preparation of Sulfonated Solid Catalyst and Its Effect in Esterification Reaction

A carbon-based sulfonated catalyst was prepared by direct sulfonation and carbonization （in moderate conditions：200 ＆#176;C, 12 h） of red liquor solids, a by-product of paper-making process. The prepared sulfonated cata-lyst （SC） had aromatic structure, composed of carbon enriched inner core, and oxygen-containing （SO3H, COOH, OH） groups enriched surface. The SO3H, COOH, OH groups amounted to 0.74 mmol·g^-1, 0.78 mmol·g^-1, 2.18 mmol·g^-1, respectively. The fresh SC showed much higher catalytic activity than that of the traditional solid acid catalysts （strong^-acid 732 cation exchange resin, hydrogen type zeolite socony mobile-five （HZSM-5）, sulfated zir-conia） in esterification of oleic acid. SC was deactivated during the reactions, through the mechanisms of leaching of sulfonated species and formation of sulfonate esters. Two regeneration methods were developed, and the catalytic activity can be mostly regenerated by regeneration Method 1 and be fully regenerated by regeneration Method 2, respectively.

Fries Rearrangement of Phenyl Acetate over Solid Acid Catalyst

A silica-supported zirconium based solid acid (ZS) has been used as catalyst for the Fries rearrangement of phenyl acetate (PA). The catalyst showed a higher PA conversion activity and a much higher selectivity for o-hydroxyacetophenone (o-HAP) than for strongly acidic zeolite catalysts. The supported catalyst was characterized by XRD, IR, XPS, pyridine-TPD and the surface area measurements. The catalytic properties were influenced significantly by pretreatment temperature.

Promoter of (Ce-Zr)O_2 Solid Solution Modified by Praseodymia in Three-Way Catalysts

The three way catalysts (TWCs) promoters (Ce Zr)O 2, (Pr Ce Zr)O 2 and (Pr Zr)O 2 were prepared by sol gel like method. They were characterized by XRD, EXAFS and BET surface area determination. The reduction features of the promoters were measured by temperature programmed reduction (TPR) of H 2 to access the potential for the promoters containing praseodymia as oxygen storage component in three way catalyst. The (Pr Zr)O 2 cubic solid solution is formed at high temperature up to 800 ℃, which makes it more reducible than the (Ce Zr)O 2 solid solution. For the (Pr Ce Zr)O 2 samples, the ternary solid solution plays an important role in the reduction process. The performance of the three way catalysts with fully formulated Pt, Pd and Rh is proceeded by using both light off temperature under a stoichiometric gas composition and the conversion of CO, C 3H 6 and NO under changing air/fuel ratio at a constant reaction temperature 400 ℃ . The results indicate that a small amount of praseodymia doping into (Ce Zr)O 2 favors the light off temperature of C 3H 6 and NO, and all the catalysts containing praseodymia obviously exhibits enhanced width of S value for NO conversion at lean region ( S ≥1.00).

Three-dimensionally ordered macroporous SnO_2-based solid solution catalysts for effective soot oxidation

A series of three‐dimensionally ordered macroporous(3DOM)SnO2‐based catalysts modified by the cations Ce4+,Mn3+,and Cu2+have been prepared by using a colloidal crystal templating method and tested for soot combustion under loose contact condition.XRD and STEM mapping results confirm that all the secondary metal cations have entered the lattice matrix of tetragonal rutile SnO2 to form non‐continuous solid solutions,thus impeding crystallization and improving the surface areas and pore volumes of the modified catalysts.In comparison with regular SnO2 nanoparticles,the 3DOM SnO2 displays evidently improved activity,testifying that the formation of the 3DOM structure can anchor the soot particulates in the macro‐pores,which ensures that the contact of the soot particles with the active sites on the 3DOM skeleton is more easily formed,thus benefiting the target reaction.With the incorporation of the secondary metal cations,the activity of the catalyst can be further improved due to the formation of more abundant mobile oxygen species.In summary,these effects are believed to be the major factors responsible for the activity of the catalyst.

Construction of a Bronsted-Lewis solid acid catalyst La-PW-SiO_(2)/SWCNTs based on electron withdrawing effect of La(Ⅲ)onπbond of SWCNTs for biodiesel synthesis from esterification of oleic acid and methanol

A novel solid Bronsted-Lewis acid catalyst La-PW-SiO_(2)/SWCNTs(single-wall carbon nanotubes)was synthesized from the synergistic modification of H_(3)PW_(12)O_(40)(HPW)by single-walled carbon nanotubes functionalized with sidewall hydroxyl groups(SWCNTs–OH)and La^(3+) via sol–gel method.The freshly prepared catalyst was characterized by several methods,and the catalytic activity and stability of it were studied from the esterification of oleic acid and methanol.Results showed that the highest conversion of oleic acid was 93.1%(mass)and maintained as high as 88.7%(mass)after six cycles of La-PW-SiO_(2)/SWCNTs.The high catalytic activity and stability of La-PW-SiO_(2)/SWCNTs can be attributed to the strong electron withdrawing effect of La^(3+) on π bond of SWCNTs,because it can facilitate the formation of a large number of strong Lewis acid sites.Therefore,the reduction of catalytic activity of a solid acid catalyst due to the fact that hydration reaction of its Bronsted acid sites can be effectively reduced.La-PW-SiO_(2)/SWCNTs can be an efficient and economical catalyst,because it shows good catalytic activity and stability.

Cu–Co–O nano-catalysts as a burn rate modifier for composite solid propellants

Nano-catalysts containing copper–cobalt oxides(Cu–Co–O) have been synthesized by the citric acid(CA) complexing method. Copper(II) nitrate and Cobalt(II) nitrate were employed in different molar ratios as the starting reactants to prepare three types of nano-catalysts. Well crystalline nano-catalysts were produced after a period of 3 hours by the calcination of CA–Cu–Co–O precursors at 550 °C. The phase morphologies and crystal composition of synthesized nano-catalysts were examined using Scanning Electron Microscope(SEM), Energy Dispersive Spectroscopy(EDS) and Fourier Transform Infrared Spectroscopy(FTIR) methods. The particle size of nano-catalysts was observed in the range of 90 nm–200 nm. The prepared nano-catalysts were used to formulate propellant samples of various compositions which showed high reactivity toward the combustion of HTPB/AP-based composite solid propellants. The catalytic effects on the decomposition of propellant samples were found to be significant at higher temperatures. The combustion characteristics of composite solid propellants were significantly improved by the incorporation of nano-catalysts. Out of the three catalysts studied in the present work, Cu Co-I was found to be the better catalyst in regard to thermal decomposition and burning nature of composite solid propellants. The improved performance of composite solid propellant can be attributed to the high crystallinity, low agglomeration and lowering the decomposition temperature of oxidizer by the addition of Cu Co-I nano-catalyst.

Biochar-based Solid Acids as Catalysts for Carbohydrate Hydrolysis: A Critical Review

Recently, increasing interest has been focused on the hydrolysis of carbohydrates to monosaccharides, among which, glucose and xylose as typical platform sugars can be used to produce chemicals and biofuels. As heterogeneous catalysts, solid acids have gained extensive attention for biomass biorefinery and could replace the conventional process owing to their excellent properties, including acceptable acidity and easy separation. In particular, biochar-based solid acids derived from biomass are promising for biomass conversion owing to the low-cost of feedstocks and the simple preparation procedure. Herein, we attempt to provide a critical overview of biochar-based solid acids for hydrolysis of carbohydrates into glucose and xylose. The preparation methods and properties of biochar-based catalysts as well as the influence of their properties on catalytic performance were discussed in detail. We also highlight the major challenges facing the use of biochar-based solid acids for carbohydrate hydrolysis.

MESOPOROUS ACID SOLID AS A CARRIER FOR METALLOCENE CATALYST IN ETHYLENE POLYMERIZATION AND A CATALYST IN CATALYTIC DEGRADATION OF POLYETHYLENE

The possibility of mesoporous acid solid as a carder for metallocene catalyst in ethylene polymerization and catalyst for polyethylene （PE） catalytic degradation was investigated. Here, HMCM-41 and AIMCM-41, and mesoporous silicoaluminophosphate molecular sieves （SAPO1 and SAPO2） were synthesized and used as acid solid. Much more gases were produced during catalytic degradation in PE/acid solid mixtures via in situ polymerization than those via physical mixing. The particle size distribution results exhibited that the particle size of SAPO1 in the PE/SAPOI mixture via in situ polymerization was about 1/14 times of that of the original SAPO1 or SAPO1-supported metallocene catalyst. This work shows a novel technology for chemical recycling of polyolefin.