New method for passive radar seeker to antagonize non-coherent radar decoy

Using super resolution direction of arrival（DOA） estimation algorithm to reduce the resolution angle is an effective method for passive radar seeker（PRS） to antagonize non-coherent radar decoy.Considering the power and correlation property between radar and non-coherent decoy,an improved subspace DOA estimation method based on traditional subspace algorithm is proposed.Because this new method uses the invariance property of noise subspace,compared with traditional MUSIC algorithm,it shows not only better resolution in condition of closely spaced sources,but also superior performance in case of different power or partially correlated sources.Using this new method,PRS can distinguish radar and non-coherent decoy with good performance.Both the simulation result and the experimental data confirm the performance of the method.

A Simple Method to Derive Minimal Cut Sets for a Non-coherent Fault Tree

Minimal cut sets （or prime implicants： minimal combinations of basic event conditions leading to system failure） are important information for reliability/safety analysis and design. To obtain minimal cut sets for general non-coherent fault trees, including negative basic events or multi-valued basic events, a special procedure such as the consensus rule must be applied to the results obtained by logical operations for coherent fault trees, which will require more steps and time. This paper proposes a simple method for a non-coherent fault tree, whose top event is represented as an AND combination of monotonic sub-trees. A ＂monotonic＂ sub-tree means that it does not have both positive and negative representations for each basic event. It is proven that minimal cut sets can be obtained by a conventional method for coherent fault trees. An illustrative example of a simple event tree analysis shows the detail and characteristics of the proposed method.

Novel non-coherent integration method using binary phase-coded radar signal

The m series with 511 bits is taken as an example being applied in non-coherent integra- tion algorithm. A method to choose the bi-phase code is presented, which is 15 kinds of codes are picked out of 511 kinds of m series to do non-coherent integration. It is indicated that the power in- creasing times of larger target sidelobe is less than the power increasing times of smaller target main- lobe because of the larger target＇ s pseudo-randomness. Smaller target is integrated from larger tar- get sidelobe, which strengthens the detection capability of radar for smaller targets. According to the sidelobes distributing characteristic, a method is presented in this paper to remove the estimated sidelobes mean value for signal detection after non-coherent integration. Simulation results present that the SNR of small target can be improved approximately 6. 5 dB by the proposed method.

ANALYSIS OF WEIGHTED NON-COHERENT RECEIVER FOR UWB-OOK SIGNAL IN MULTIPATH CHANNELS

Non-coherent receivers are attractive for pulsed Ultra-WideBand (UWB) systems due to the implementation simplicity. However, they have to face the shortage of performance degradation. Several techniques were proposed to alleviate the noise effect and promote the receiver performance, among which is the weighted combining of multiple integration sub-intervals. In this paper, the performance of the weighted non-coherent receiver for UWB On-Off Keying (UWB-OOK) signal in multipath channels is analyzed, in terms of bit-error-rate. In addition, a closed-form expression of the approximately near-optimal weighting coefficient set is derived, and two simple weighting coefficient sets are proposed as well. Finally, the analytic results are verified via the computer simulations, which reveal obvious performance improvements to the conventional energy detector.

Non-coherent sequence detection scheme for satellite-based automatic identification system

The satellite-based automatic identification system (AIS) receiver has to encounter the frequency offset caused by the Doppler effect and the oscillator instability. This paper proposes a non-coherent sequence detection scheme for the satellite-based AIS signal transmitted over the white Gaussian noise channel. Based on the maximum likelihood estimation and a Viterbi decoder, the proposed scheme is capable of tolerating a frequency offset up to 5% of the symbol rate. The complexity of the proposed scheme is reduced by the state-complexity reduction, which is based on per-survivor processing. Simulation results prove that the proposed non-coherent sequence detection scheme has high robustness to frequency offset compared to the relative scheme when messages collision exists.

PERFORMANCE OF NON-COHERENT RECEIVER WITH UWB PPM SIGNAL IN MULTIPATH CHANNELS

Mainly due to its implementation simplicity, the non-coherent Ultra-Wide Band (UWB) receiver is attractive for lower data rate applications, which gains much attention again in recent years. In this paper, a General Likelihood Ratio Test (GLRT) based non-coherent receiver on UWB Pulse-Position-Modulation (PPM) signal in multipath channels is derived, and a novel structure is proposed as well. Subsequently, the closed-form expressions of asymptotic error-rate performance related to the non-coherent receiver are also derived and verified.

Projectile impact point prediction method based on GRNN

In order to forecast projectile impact points quickly and accurately,aprojectile impact point prediction method based on generalized regression neural network（GRNN）is presented.Firstly,the model of GRNN forecasting impact point is established;secondly,the particle swarm algorithm（PSD）is used to optimize the smooth factor in the prediction model and then the optimal GRNN impact point prediction model is obtained.Finally,the numerical simulation of this prediction model is carried out.Simulation results show that the maximum range error is no more than 40 m,and the lateral deviation error is less than0.2m.The average time of impact point prediction is 6.645 ms,which is 1 300.623 ms less than that of numerical integration method.Therefore,it is feasible and effective for the proposed method to forecast projectile impact points,and thus it can provide a theoretical reference for practical engineering applications.

A hypersonic target coherent integration detection algorithm based on Doppler feedback

The traversal search of multi-dimensional parameter during the process of hypersonic target echo signal coherent integration,leads to the problem of large amounts of calculation and poor real-time performance.In view of these problems,a modified polynomial Radon-polynomial Fourier transform(MPRPFT)hypersonic target coherent integration detection algorithm based on Doppler feedback is proposed in this paper.Firstly,the Doppler estimation value of the target is obtained by using the target point information obtained by subsequent non-coherent integration detection.Then,the feedback adjustment of the coherent integration process is performed by using the acquired target Doppler estimation value.Finally,the coherent integration is completed after adjusting the search interval of compensation.The simulation results show that the algorithm can effectively reduce the computational complexity and improve the real-time performance on the basis of the effective coherent integration of hypersonic target echo signals.

An energy detection receiver for non-coherent IR-UWB

A non-coherent receiver for impulse radio ultra-wide band（IR-UWB）is presented.The proposed receiver front-end consists of a high gain LNA,a high frequency detector and an intermediate frequency（IF）amplifier to amplify the recovered signal and drive an external test instrument.To meet the requirements of high gain and a low noise figure（NF）under moderate power consumption for the LNA,capacitor cross coupled（CCC）and current reuse techniques were adopted.The detector consists of a squarer and an integrator.The overall circuit consumes 41.2mA current with a supply voltage of 1.8 V at a 400 MHz pulse rate.The resulting energy efficiency is 0.19 nJ/pulse.A chip prototype is implemented in 0.18-μm CMOS.The die area is 2.1×1.4 mm^2 and the active area is 1.7×0.98 mm^2.

MIMO-FSK non-coherent detection with spatial multiplexing in fast-fading environment

Accurate estimationand real-time compensation for phase offset and Doppler shift are essential for coherent multi-input multi-output(MIMO)systems.Here,a spatial multiplexing MIMO scheme with non-coherent frequency-shift keying(FSK)detection is proposed.It is immune to random phase interference and Doppler shift while increasing capacity.It is valuable that the proposed spatial multiplexing MIMO based on energy detection(ED)is equivalent to a linear system,and there is no mutual interference caused by the product of simultaneous signals in square-law processing.The equivalent MIMO channel model is derived as a real matrix,which remains maximal multiplexing capacity and reduces the channel estimation complexity.Simulation results show that the proposed scheme has outstanding performance over Rician flat fading channel,and experimental system obtains four times the capacity through 4 antennas on both transmitter and receiver.

Long term integration of radar signals with unknown Doppler shift for ubiquitous radar

Ubiquitous radar is a new radar system that provides continuous and uninterrupted multifunction capability within a coverage volume. Continuous coverage from close-in ＂pop-up＂ targets in clutter to long-range targets impacts selection of waveform parameters. The coherent processing interval （CPI） must be long enough to achieve a certain signal-to-noise ratio （SNR） that ensures the efficiency of detection. The condition of detection in the case of low SNR is analyzed, and three different cases that would occur during integration are discussed and a method to determine the CPI is presented. The simulation results show that targets detection with SNR as low as -26 dB in the experimental system can possibly determine the CPI.

Weak GPS L1 Signal Acquisition Based on BPDC

It is difficult to achieve accurate acquisition of weak global positioning system( GPS) signals with traditional methods. A weak signal acquisition strategy based on block processing and differentially coherent( BPDC) is put forward after analyzing the advantages and disadvantages of coherent and non-coherent integration algorithms. Code phase parallel search of the pre-coherent integration is conducted by using fast Fourier transform( FFT),and the results are then differential coherent processed and block processed. BPDC method reduces computation cost compared with coherent and noncoherent( CNC) algorithm. The performance of the two algorithms is also compared based on simulated signals. The result shows that the noise suppression effect of BPDC algorithms is superior to that of traditional CNC algorithm,and the superiority of BPDC is more apparent with the reduction of carrier to noise ratio( CNR). In the case that the pre-coherent integration length is 4 ms and CNR is reduced to 28 dB-Hz,CNC algorithm cannot yet acquire signal correctly while BPDC has well acquisition performance. Therefore,for weak GPS signal acquisition,BPDC algorithm can acquire the signal with lower CNR and has better acquisition property.

A Blackman-Harris windowed triple-spectrum-line interpolation method for measuring SNR of ADCs

In the practical measurement of signal to noise ratio(SNR)of analog-to-digital converters(ADCs)by using fast Fourier transformation(FFT)method,the non-coherent sampling is inevitable,leading to spectral leakage which in turn affects the calculation accuracy and final measurement results.In this paper,a new method based on the Blackman-Harris windowed triple-spectrum-line interpolation is presented for the measurement of ADCs SNR by FFT.The simulation platform is built based on MATLAB and the behavioral dynamic models of the high-speed ADC products of Analog Devices Inc.(ADI)are simulated.The simulation results show that,even in the case of the maximum non-coherent degree,the SNR error is less than0.23dB and reaches the testing standards provided by ADI,confirming that the proposed method is effective for suppressing the spectral leakage effects and improving the SNR test accuracy.

Constant False Alarm Rate Acquisition Algorithm for Compass B1C Signal

In order to improve the sensitivity of the Compass B1C signal acquisition for the receiver,the principle of constant false alarm rate(CFAR)is applied for the B1C pilot channel acquisition to realize the dynamic adjustment of the threshold of acquisition against the carrier to noise ratio.The non-coherent data/pilot combined acquisition algorithm for B1C signal is analyzed to make full use of the power of the B1C signal under the condition of low carrier to noise ratio.On this basis,to improve the acquisition sensitivity of the receiver,the principle of constant false alarm probability is applied for the non-coherent data/pilot combined acquisition algorithm.Theoretical analysis and simulations show that the non-coherent data/pilot combined acquisition algorithm with CFAR improves the B1C signal acquisition sensitivity of the receiver significantly,and achieves a better Receiver Operating Characteristic compared with the traditional acquisition algorithms.

MICROSTRUCTURE OF DIFFERENTLY TREATED Al-Mg-Sc-Zr ALLOYS

The microstructures of different treated Al-5Mg-0.5Sc-0. 1Zr alloys have been studied with opticalmicroscopy and transmission electron microscope (TEM). Coherent particles with the matrix were found inas-cast sample. composite Al3Sc/Al3Zr particles were found after 13 h homogenized treatment under 470℃.Coherent precipitates pinned dislocations and low-angle grain boundaries. and then restrained recrystallization. All kinds of particles of different treatments were not larger than 40nm. After high-temperaturestabilization treatments, most particles remain coherent with the matrix. The reasons of microstructurechange at different treated conditions have been analyzed.

Target estimation using MIMO radar with multiple subcarriers

This paper analyzes the effect of waveform parame- ters on the joint target location and velocity estimation by a non- coherent multiple input multiple output （MIMO） radar transmitting multiple subcarriers signals. How the number of subcarriers in- fluences the estimation accuracy is illustrated by considering the joint Cramer-Rao bound and the mean square error of the maxi- mum likelihood estimate. The non-coherent MIMO radar ambiguity function with multiple subcarriers is developed and investigated by changing the number of subcarriers, the pulse width and the frequency spacing between adjacent subcarriers. The numerical results show that more subcarriers mean more accurate estimates, higher localization resolution, and larger pulse width results in a worse performance of target location estimation, while the fre- quency spacing affects target location estimation little.

New Iterated Decoding Algorithm Based on Differential Frequency Hopping System

A new iterated decoding algorithm is proposed for differential frequency hopping (DFH) encoder concatenated with multi-frequency shift-key (MFSK) modulator. According to the character of the frequency hopping (FH) pattern trellis produced by DFH function, maximum a posteriori (MAP) probability theory is applied to realize the iterate decoding of it. Further, the initial conditions for the new iterate algorithm based on MAP algorithm are modified for better performance. Finally, the simulation result compared with that from traditional algorithms shows good anti-interference performance.

Comparison of Kurtosis and Fourth Power Detectors with Applications to IR-UWB OOK Systems

On-off keying (OOK) is one of the modulation schemes for non-coherent impulse radio Ultra-wideband systems. In this paper, the utilization of the kurtosis detector (KD) and fourth power detector (FD) receivers for OOK signaling is introduced. We investigate the effect of integration interval and the optimum threshold on the performance of energy detector (ED), KD and FD receivers. The semi analytic expression of BER is obtained by using generalized extreme value distribution function for KD and FD receivers. From performance point of view, the simulation results show that FD receiver outperforms KD and ED receivers. In contrast, the sensitivity to the optimum threshold is greatly reduced in KD receiver compared to ED and FD receivers.

Progress and Development Direction of “Three-High” Oil and Gas Well Testing Technology

By reviewing the development of “three-high” oil and gas well testing technology of Sinopec in recent years, this paper systematically summarizes the application of “three-high” oil and gas well testing technology of Sinopec in engineering optimization design technology, and high temperature and high pressure testing technology, high pressure and high temperature transformation completion integration technology. Major progress has been made in seven aspects: plug removal and re-production technology of production wells in high acid gas fields;wellbore preparation technology of ultra-deep, high-pressure, and high-temperature oil and gas wells;surface metering technology;and supporting tool development technology. This paper comprehensively analyzes the challenges faced by the “three-high” oil and gas well production testing technology in four aspects: downhole tools, production testing technology, safe production testing, and the development of low-cost production test tools. Four development directions are put forward: 1) Improve ultra-deep oil and gas testing technology and strengthen integrated geological engineering research. 2) Deepen oil and gas well integrity evaluation technology to ensure the life cycle of oil and gas wells. 3) Carry out high-end, customized, and intelligent research on oil test tools to promote the low-cost and efficient development of ultra deep reservoirs. 4) Promote the fully automatic control of the surface metering process to realize the safe development of “three-high” reservoirs.

Favourable and Unfavourable EMF Frequency Patterns in Cancer:Perspectives for Improved Therapy and Prevention

Carcinogenesis fits in a frequency pattern of electromagnetic field (EMF) waves, in which a gradual loss of cellular organization occurs. Such generation of cancer features can be inhibited by adequate exposure to coherent electromagnetic frequencies. However, cancer can also be initiated and promoted at other distinct frequencies of electromagnetic waves. Both observations were revealed by analyzing 100 different EMF frequency data reported in a meta-analyses of 123 different, earlier published, biomedical studies. The studied EM frequencies showed a fractal pattern of 12 beneficial (anti-cancer) frequencies, and 12 detrimental (cancer promoting) frequencies, that form the central pattern of a much wider self-similar EMF spectrum of cancer inhibiting or promoting activities. Inhibiting of the cancer process, and even curing of the disease, can thus be considered through exposure to the coherent type of EM fields. Stabilization of the disease can be understood by constructive resonance of macromolecules in the cancer cell with the externally appied coherent EMF field frequencies, called solitons/polarons. The latter, for instance, have been shown earlier to induce repair in DNA/RNA conformation and/or epigenetic changes. The field of EMF treatment of cancer disorders is rapidly expanding and our studies may invite further experimental and clinical studies in which systematically various potential EMF treatment protocols could be applied, with combined and modulated frequencies, to obtain even more efficient EMF anti-cancer therapies.