基于模糊n-cell数的非线性投入产出模型解的存在性

将混合单调以及耦合不动点的概念引入到模糊n-cell数空间中,给出此空间上的混合单调型不动点定理。考虑到模糊n-cell数具有表示n维不确定信息的特点,将非线性投入产出模型与模糊n-cell数相结合,建立模糊非线性投入产出模型并给出相应的平衡方程。最后利用本文中所给的不动点定理讨论此模型解存在的条件,验证模型的合理性。

Influence of Dry Methane Reactions on the Cell Output Characteristics of Solid Oxide Fuel Cells

In order to study the influence of dry methane concentration on outputs in solid oxide fuel cells (SOFCs), the output performance was obtained for dry methane of different concentrations on a Ni-ScSZ anode in solid oxide fuel cells, and the anode exhaust gas was measured by online chromatography. The underlying causes of the output performance change were analyzed from the anode reactions by summarizing the anode exhaust gas regular pattern for different reactions, and analyzing the electrochemical reaction kinetics of methane with oxygen ion. As the oxygen ion concentration at the anode three-phase boundary proportionally increased with current density, the following reactions occurred for different dry methane concentrations in sequence CH4 + O2﹣ → CO + 2H2 + 2e﹣, CH4 + 2O2﹣ → CO + H2O + H2 + 4e﹣, CH4 + 3O2﹣ → CO + 2H2O + 6e﹣, CH4 + 4O2﹣ → CO2 + 2H2O + 8e﹣. With various concentrations of methane at a low current, the outlet methane continuously reduced with the increase of the current density. Meanwhile, CO and H2 exhaust gas increased with increasing current density for low concentration of methane. With methane concentrations at 3.85% and 5.66%, the cell output voltage dropped rapidly. For concentrations of 29.7% and 3.85%, the anode exhaust residual methane changed irregularly with current density and this phenomenon was associated with the dry methane that reacted on anode of the cell. The transformation of reactions, the water produced in the electrochemical reactions and the polarization in response to the change of reactions maybe induced the output voltage and power density reducing as low concentrations of dry methane were used.

Dual Mode-Multiple Output SEPIC Converter Integrated with Passive Ripple Cancelling Circuit for Standalone PV Energy Harvesting System

This document addresses an exhaustive standalone Photovoltaic (PV) energy harvesting system considering two crucial issues: system efficiency and cost effectiveness. It contributes a compact resolution with a combined feature of Dual Mode-Multiple Output (DMMO) associated with input ripple reduction technique. Control strategy incorporates with aspect of Maximum Power Point Tracking (MPPT) and output voltage levels regulation. A theoretical analysis is conducted to evaluate the effect of ripple current on PV power. Proposed dual mode converter achieves efficiency of 98.36% and 97.76% respectively for mode-1 and mode-2 operation. However, simulation is performed applying MATLAB/SIMULINK tools to analyze the feasibility of the recommended system.

Influence of Cathode Modification by Chitosan and Fe^(3+)on the Electrochemical Performance of Marine Sediment Microbial Fuel Cell

The electrochemical performances of cathode play a key role in the marine sediment microbial fuel cells(MSMFCs)as a long lasting power source to drive instruments,especially when the dissolved oxygen concentration is very low in seawater.A CTS-Fe^(3+)modified cathode is prepared here by grafting chitosan(CTS)on a carbon fiber surface and then chelating Fe^(3+)through the coordination process.The electrochemical performance in seawater and the output power of the assembled MSMFCs are both studied.The results show that the exchange current densities of CTS and the CTS-Fe^(3+)group are 5.5 and 6.2 times higher than that of the blank group,respectively.The potential of the CTS-Fe^(3+)modified cathode increases by 138 mV.The output power of the fuel cell(613.0 mW m^(-2))assembled with CTS-Fe^(3+)is 54 times larger than that of the blank group(11.4 mW m^(-2))and the current output corresponding with the maximum power output also increases by 56 times.Due to the valence conversion between Fe^(3+)and Fe^(2+)on the modified cathode,the kinetic activity of the dissolved oxygen reduction is accelerated and the depolarization capability of the cathode is enhanced,resulting higher cell power.On the basis of this study,the new cathode materials will be encouraged to design with the complex of iron ion in natural seawater as the catalysis for oxygen reduction to improve the cell power in deep sea.

Evaluation of Linear Precoding Schemes for Cooperative Multi-Cell MU MIMO in Future Mobile Communication Systems

In Mobile Communication Systems, inter-cell interference becomes one of the challenges that degrade the system’s performance, especially in the region with massive mobile users. The linear precoding schemes were proposed to mitigate interferences between the base stations (inter-cell). These schemes are categorized into linear and non-linear;this study focused on linear precoding schemes, which are grounded into three types, namely Zero Forcing (ZF), Block Diagonalization (BD), and Signal Leakage Noise Ratio (SLNR). The study included the Cooperative Multi-cell Multi Input Multi Output (MIMO) System, whereby each Base Station serves more than one mobile station and all Base Stations on the system are assisted by each other by shared the Channel State Information (CSI). Based on the Multi-Cell Multiuser MIMO system, each Base Station on the cell is intended to maximize the data transmission rate by its mobile users by increasing the Signal Interference to Noise Ratio after the interference has been mitigated due to the usefully of linear precoding schemes on the transmitter. Moreover, these schemes used different approaches to mitigate interference. This study mainly concentrates on evaluating the performance of these schemes through the channel distribution models such as Ray-leigh and Rician included in the presence of noise errors. The results show that the SLNR scheme outperforms ZF and BD schemes overall scenario. This implied that when the value of SNR increased the performance of SLNR increased by 21.4% and 45.7% for ZF and BD respectively.

微生物燃料电池工作原理及产电性能提升策略

微生物燃料电池(MFC)是一种解决其他能源在环境方面不足的新技术,目前低能量输出是MFC实际应用的关键瓶颈。基于MFC工作原理,提出微生物活性差、电子迁移阻力、质子传输阻力及阴极还原反应缓慢是MFC能量输出的限制因素,并从以下5个方面综述了提升MFC产电性能策略:调节pH和选择最佳盐度,加强微生物代谢活性;改性阳极材料,降低电子迁移阻力;增强电解液电导率、优化隔膜材料及缩短电极间距减小质子传输阻力;制备高效阴极催化剂和选择优异电子受体加快阴极还原反应速率;改进MFC反应器构型,提高整体产电性能。未来,可在合成新型阴极催化剂、降低膜污染、优化微生物生长环境、制备优异的电极材料和改进MFC反应器配置5个方面开展重点研究。

基于SWIPT的无小区大规模MIMO-NOMA系统能量效率研究

无小区大规模多输入多输出(Multiple-Input Multiple-Output,MIMO)与非正交多址接入(Non-Orthogonal Multiple Access,NOMA)都是未来6G的使能技术。无线携能通信(Simultaneous Wireless Information and Power Transfer,SWIPT)技术在进行信息解码的同时收集能量,与无小区大规模MIMO-NOMA优势互补。文中基于SWIPT研究无小区大规模MIMO-NOMA系统中的能量效率问题,通过联合优化功率分配系数和SWIPT的时隙切换(Time Switching,TS)系数,提高系统的能量效率。为了最大化能量效率,采用布谷鸟算法设计功率分配系数。考虑一种特殊情况,将所有终端的TS系数设置相同,进而推导了最佳TS系数的封闭表达式。仿真结果表明,相较于几种已有方案,文中提出的优化方案可以显著提升系统的能量效率。

单相无桥功率因数校正变换器拓扑族推演回顾与性能分类总结

随着多种节能标准与低碳政策的实施,单相无桥功率因数校正(power factor correction,PFC)拓扑受到更多关注。目前,虽然多种无桥拓扑已被提出并被应用于不同应用场合,但尚未有文献系统地概述这类无桥PFC拓扑结构特点并开展拓扑性能分析。该文通过将双变换单元进行输入并联输出并联(input-parallel output-parallel,IPOP)、输入并联输出串联(input-parallel output-series,IPOS),提出无桥拓扑族系统推演方法以及无桥拓扑IPOP与IPOS的分类。同时,以6种变换单元为例,推演28种无桥拓扑并作相关拓扑概述,说明无桥拓扑族系统推演方法的普适性。其次,通过对称性与对偶性,进一步简化无桥拓扑族的器件数量。然后,筛选出12种主要无桥拓扑与传统有桥拓扑比较,并分别介绍12种无桥拓扑性能特点。最后,基于性能对比结果,归纳IPOS与IPOP两类拓扑的优缺点与适用场景。

质子交换膜燃料电池性能优化控制

质子交换膜燃料电池(proton exchange membrane fuel cell,PEMFC)的热管理,是影响PEMFC安全、稳定、高效运行的核心关键因素。该文在分析PEMFC热管理子系统的结构,以及关键组成部件(包括空气压缩机、冷却液循环泵和冷却风扇)的工作原理基础上,首先搭建耦合热管理子系统的PEMFC非线性仿真模型,进一步将其简化处理得到用于控制的线性模型;在此基础上,设计基于卡尔曼滤波的状态观测器,以实现对状态和不可测量扰动的估计,从而消除模型稳态误差;随后设计目标计算器,以净输出功率跟踪误差最小化和系统效率最大化为目标,对PEMFC系统工作状态进行优化;进而基于线性控制模型,设计无偏显式模型预测控制(offset-free explicit model predictive control,offset-free EMPC),对优化工作状态进行跟踪控制;最后,搭建一个软件在环(softwareintheloop,Si L)测试平台,通过与传统MPC控制策略的仿真结果对比可得,无偏EMPC控制策略可以显著将净输出功率的平均跟踪误差绝对值从344.29W减小到82.19W,系统效率从40.32%提升到46.56%,算法平均单步计算耗时从26ms降低到11.8ms,并且可以约束PEMFC系统运行在稳定和安全的工况。

RIS辅助的无蜂窝大规模MIMO关键技术研究

针对密集蜂窝组网干扰受限难题,无蜂窝大规模MIMO利用大规模宏分集,构建以用户为中心的新架构,大规模灵活协作显著提升每个用户性能。同时,无蜂窝辅以智能超表面技术,以低成本和低功耗极大提升网络容量。聚焦研究了RIS辅助的无蜂窝大规模MIMO天线校准和导频分配两个关键问题。针对大规模RAU校准难题,首先在最低校准信噪比和校准相干时间约束下,提出动态分簇的可自愈校准拓扑构建方法,然后为降低校准时域开销,设计了RAU簇内和簇间校准时序,研究了可扩展的天线校准算法,能实现任意多RAU联合相位校准。针对导频分配问题,首先提出基于空间高相关性的用户动态簇的构建新方法,然后提出用户簇内基于信道相关性最低和用户簇间最小复用概率的导频分配方法。仿真结果表明,提出的校准算法具有较小的校准误差和较好的扩展性。同时,提出的导频分配算法性能可逼近最大化容量导频分配算法,且复杂度大幅降低。

基于BaCo_(0.4)Fe_(0.4)Zr_(0.1)Y_(0.1)O_(3-δ)空气电极的可逆质子陶瓷膜电池性能研究

采用柠檬酸络合-硝酸盐燃烧法合成的BaCo_(0.4)Fe_(0.4)Zr_(0.1)Y_(0.1)O_(3-δ)(BCFZY)作为空气电极材料,组装了燃料电极支撑的可逆质子陶瓷膜电池(R-HCMC),并且探讨了单电池在不同工作模式下的电化学性能。结果表明:在900℃下合成的BCFZY表现为单一立方钙钛矿结构,在700℃燃料电池模式下,单电池最大输出功率为424.7 mW·cm^(-2)、最低的极化阻抗为0.23Ω·cm^(2);在电解模式下,电解电压为1.4 V时,最大电流密度为1084 mW·cm^(-2)、氢气产率为3.1 mL·min^(-1)·cm^(-2)。说明,BCFZY空气电极在中低温条件下表现出良好的电催化活性和结构与性能稳定性。

Credit Risk Model Taking Account of Inflation and Its Contribution to Macroeconomic Discussion on Effect of Inflation on Output Growth

We use Extended Merton model(EMM)for estimating the firm’s credit risks in the presence of inflation.We show quantitatively that inflation is an influential factor making either a benign or adverse effect on the firm’s survival,supporting at the microeconomic level New Keynesian findings of the nonlinear inflation effect on output growth.Lower inflation increasing the firm’s expected rate of return can raise its mean year returns and decrease its default probability.Higher inflation,decreasing the expected rate return,makes the opposite effect.The magnitude of the adverse effect depends on the firm strength:for a steady firm,this effect is small,whereas for a weaker firm,it can be fatal.EMM is the only model taking account of inflation.It can be useful for banks or insurance companies estimating credit risks of commercial borrowers over the debt maturity,and for the firm’s management planning long-term business operations.

Non-Linear Mathematical Model of the Interaction between Tumor and Oncolytic Viruses

A mathematical modeling of tumor therapy with oncolytic viruses is discussed. The model consists of two coupled, deterministic differential equations allowing for cell reproduction and death, and cell infection. The model is one of the conceptual mathematical models of tumor growth that treat a tumor as a dynamic society of interacting cells. In this paper, we obtain an approximate analytical expression of uninfected and infected cell population by solving the non-linear equations using Homotopy analysis method (HAM). Furthermore, the results are compared with the numerical simulation of the problem using Matlab program. The obtained results are valid for the whole solution domain.

Effect of bamboo charcoal filler on the performance of microbial fuel cell

微生物燃料电池（MFC）的阳极对提高MFC产电性能有至关重要的影响.利用竹炭比表面积大、吸附能力强等特性,将其作为“三合一”膜电极MFC的阳极填充材料,通过增大阳极比表面积来提高其产电能力.实验结果表明,加入竹炭至阳极室后,MFC最高输出电压（外接电阻1 000Ω时）由0.280V增大到0.387V,提高了38.2％,并且输出电压更加稳定;而最大功率密度也由原来的0.22 W/m3增大到1.42 W/m3,同时内阻降低了80.85％（由235 Ω降为45 Ω）;库仑效率由15.0％增大到25.6％.说明MF℃阳极室填充竹炭可以显著促进MFC的产电性能.

Electrochemical Properties of Electrodes with Different Shapes and Diffusion Kinetic Analysis of Microbial Fuel Cells on Ocean Floor

Microbial fuel cell(MFC) on the ocean floor is a kind of novel energy-harvesting device that can be developed to drive small instruments to work continuously.The shape of electrode has a great effect on the performance of the MFC.In this paper,several shapes of electrode and cell structure were designed,and their performance in MFC were compared in pairs:Mesh(cell-1) vs.flat plate(cell-2),branch(cell-3) vs.cylinder(cell-4),and forest(cell-5) vs.disk(cell-6) FC.Our results showed that the maximum power densities were 16.50,14.20,19.30,15.00,14.64,and 9.95 mWm-2 for cell-1,2,3,4,5 and 6 respectively.And the corre-sponding diffusion-limited currents were 7.16,2.80,18.86,10.50,18.00,and 6.900 mA.The mesh and branch anodes showed higher power densities and much higher diffusion-limited currents than the flat plate and the cylinder anodes respectively due to the low diffusion hindrance with the former anodes.The forest cathode improved by 47% of the power density and by 161% of diffusion-limited current than the disk cathode due to the former's extended solid/liquid/gas three-phase boundary.These results indicated that the shape of electrode is a major parameter that determining the diffusion-limited current of an MFC,and the differences in the elec-trode shape lead to the differences in cell performance.These results would be useful for MFC structure design in practical applica-tions.

A pilot allocation method for multi-cell multi-user massive MIMO system

Pilot contamination can spoil the accuracy of channel estimation and then has become one of the key problems influencing the performance of massive multiple input multiple output(MIMO)systems.This paper proposes a method based on cell classification and users grouping to mitigate the pilot contamination in multi-cell massive MIMO systems and improve the spectral efficiency.The pilots of the terminals are allocated onebit orthogonal identifier to diminish the cell categories by the operation of exclusive OR(XOR).At the same time,the users are divided into edge user groups and central user groups according to the large-scale fading coefficients by the clustering algorithm,and different pilot sequences are assigned to different groups.The simulation results show that the proposed method can effectively improve the spectral efficiency of multi-cell massive MIMO systems.

Carbon Foam Anode Modified by Urea and Its Higher Electrochemical Performance in Marine Benthic Microbial Fuel Cell

Electrode materials have an important effect on the property of microbial fuel cell(MFC). Carbon foam is utilized as an anode and further modified by urea to improve its performance in marine benthic microbial fuel cell(BMFC) with higher voltage and output power. The electrochemical properties of plain carbon foam(PC) and urea-modified carbon foam(UC) are measured respectively. Results show that the UC obtains better wettability after its modification and higher anti-polarization ability than the PC. A novel phenomenon has been found that the electrical potential of the modified UC anode is nearly 100 m V lower than that of the PC, reaching-570 ±10 m V(vs. SCE), and that it also has a much higher electron transfer kinetic activity, reaching 9399.4 m W m-2, which is 566.2-fold higher than that from plain graphite anode(PG). The fuel cell containing the UC anode has the maximum power density(256.0 m W m-2) among the three different BMFCs. Urea would enhance the bacteria biofilm formation with a more diverse microbial community and maintain more electrons, leading to a lower anodic redox potential and higher power output. The paper primarily analyzes why the electrical potential of the modified anode becomes much lower than that of others after urea modification. These results can be utilized to construct a novel BMFC with higher output power and to design the conditioner of voltage booster with a higher conversion ratio. Finally, the carbon foam with a bigger pore size would be a potential anodic material in conventional MFC.

Web Tension Regulation of Multispan Roll-to-Roll System using Integrated Active Dancer and Load Cells for Printed Electronics Applications

The mass production of printed electronics can be achieved by roll-to-roll(R2R) printing system, so highly accurate web tension is required that can minimize the register error and keep the thickness and roughness of printed devices in limits. The web tension of a R2R system is regulated by the use of integrated load cells and active dancer system for printed electronics applications using decentralized multi-input-single-output(MISO) regularized variable learning rate backpropagation artificial neural networks. The active dancer system is used before printing system to reduce disturbances in the web tension of process span. The classical PID control result in tension spikes with the change in roll diameter of winder and unwinder rolls. The presence of dancer in R2R system shows that improved web tension control in printing span and the web tension can be enhanced from 3.75 N to 4.75 N. The overshoot of system is less than ±2.5 N and steady state error is within ±1 N where load cells have a signal noise of ±0.7 N. The integration of load cells and active dancer with self-adapting neural network control provide a solution to the web tension control of multispan roll-to-roll system.

质子交换膜燃料电池流道尺寸优化

质子交换膜燃料电池具有比能量高、清洁高效等优点,流道作为燃料电池的核心结构之一,其结构尺寸对气体传输、液态水排出都有着重要影响,选择合适尺寸参数对实际运行具有重要意义。以50 mm×50 mm单蛇形流道电池为研究对象,采用数值模拟的方法,建立质子交换膜燃料电池三维两相等温模型,分析流道深度、流道宽度、流道脊宽等参数对电池电流密度、气体传质特性、电池净输出功率、排水性能的影响。结果表明:随着流道深度、流道宽度的减小,参与反应的氧气浓度提高,电流密度也随之提高,电池净输出功率逐渐增大,催化层排水性能逐渐增强,因此电池性能逐渐提高;随着流道脊宽的减小,参与反应的氧气浓度逐渐提高,电流密度随之增大,但电池净输出功率增加幅度较小,氧气浓度增加也较缓慢。

基于低分辨率DAC的IRS辅助去蜂窝大规模MIMO系统联合预编码设计

本文研究了下行链路智能反射面(Intelligent Reflective Surface, IRS)辅助去蜂窝大规模MIMO(Cell-Free Massive Multiple-Input Multiple-Output)系统,其中每个接入点(Access Point, AP)都采用了低分辨率的数模转换器(Digital-to-Analog Converters,DAC)。本文将IRS应用于去蜂窝系统并在AP处配备低分辨率DAC,进一步降低了硬件成本和功耗。采用加性量化噪声模型对低分辨率DAC进行数学建模,进而建立了下行链路用户和速率的表达式。由于公式具有非凸性和高复杂性,本文提出了一个交替优化框架来解决此问题,从而提高用户和速率。特别地,我们通过分数规划解耦这个问题,并采用拉格朗日乘子法和半定规划(Semi-Definite Programming,SDP)方法求得预编码矩阵和相移矩阵的表达式。最后,仿真结果表明,与传统的去蜂窝网络相比,该方案下的网络容量可以显著提高。