Theoretical and numerical research on the dynamic launch response of carbon fiber composite cartridges

Understanding the dynamic response of composite material cartridges during the firing process is of great significance for improving their reliability and safety.A theoretical model describing the dynamic response of composite material cartridges is established based on the thick-walled cylinder theory and rate-dependent constitutive model of composite materials.The correctness of the theoretical model is validated through finite element simulations of cartridge deformation.The influence of chamber pressure and cartridge wall thickness on the cartridge's deformation process and stress distribution is analyzed.The results indicate that the primary deformation of composite material cartridges inside the chamber is elastic deformation.Compared to metal cartridges,composite material cartridges require higher pressure for touching-chamber and are more prone to developing gaps after unloading to ensure smooth extraction.During the deformation process,the touching-chamber behavior of the cartridge can improve the stress distribution.Under the same chamber pressure,the touching-chamber behavior can reduce the circumferential stress by approximately 30%.The inner wall surface of the cartridge is a critical area that requires attention.The touching-chamber behavior can be facilitated by appropriately reducing the cartridge wall thickness while ensuring overall strength.This study can provide guidance for the optimization design of composite material cartridges.

Effect of continuous casting speed on mold surface flow and the related near-surface distribution of non-metallic inclusions

For the control of surface defects in interstitial-free(IF) steel, quantitative metallographic analyses of near-surface inclusions and surface liquid flow detection via the nail-board tipping method were conducted. The results show that, at casting speeds of 0.8 and 1.0 m/min, a thin liquid mold flux layer forms and non-uniform floating of argon bubbles occurs, inducing the entrainment and subsequent entrapment of the liquid flux; fine inclusion particles of Al_2O_3 can also aggregate at the solidification front. At higher casting speeds of 1.4 and 1.6 m/min, the liquid mold flux can be entrained and carried deeper into the liquid steel pool because of strong level fluctuations of the liquid steel and the flux. The optimal casting speed is approximately 1.2 m/min, with the most favorable surface flow status and, correspondingly, the lowest number of inclusions near the slab surface.

Study on the separation process of non-metallic inclusions at the steel-slag interface using water modeling

The separation process of non-metallic inclusions at the steel–slag interface was simulated by physical modeling. Three different kinds of particles(octahedral, plate-like, and spherical) and three different oils(kerosene, bean oil, and pump oil) were used to model inclusions and slags, respectively. The effects of inclusion geometry(shape and size) and slag properties(viscosity and interfacial tension) on the separation process were investigated. The results revealed that the variation of surface free energy and the viscosity of the slag are two significant factors affecting the separation process of inclusions at the steel–slag interface. The variation of surface free energy helped inclusions enter the slag phase, whereas the decrease of slag viscosity shortened the separation time. The deformation of the steel–slag interface could give rise to the resistance force, which would resist inclusions passing through the interface. A liquid film formed on the inclusion as it passed through the steel–slag interface, which might be related to the inclusion's shape.

Study on non-metallic inclusions in Al killed high strength alloy steel refined by high basicity and high Al_2O_3 content slag

Laboratory and industrial studies were carried out to investigate non-metallic inclusions in high strength alloy steel refined by high basicity and high Al_2O_3 slag.It was found that the steel/slag reaction time largely affected non-metallic inclusions.With the reaction time increased from 30 min to 90 min in laboratory study,MgO-Al_2O_3 spinels were gradually changed into CaO-MgO-Al_2O_3 system inclusions surrounded by softer CaO-Al_2O_3 surface layers.By using high basicity slag which contained as much as 41%Al_2O_3 in the laboratory study,ratio of low melting temperature CaO-MgO-Al_2O_3 system inclusions was remarkably increased to above 80%.In the industrial experiment,during the secondary refining,the inclusions changed in order of 'Al_2O_3→MgO-Al_2O_3→CaO-MgO-Al_2O_3'.Through the LF and RH refining,most inclusions could be transferred to lower melting temperature CaO-Al_2O_3 and CaO-MgO-Al_2O_3 system inclusions.

Current Trends and Perspectives of Detection and Location for Buried Non-Metallic Pipelines

Buried pipelines are an essential component of the urban infrastructure of modern cities.Traditional buried pipes are mainly made of metal materials.With the development of material science and technology in recent years,non-metallic pipes,such as plastic pipes,ceramic pipes,and concrete pipes,are increasingly taking the place of pipes made from metal in various pipeline networks such as water supply,drainage,heat,industry,oil,and gas.The location technologies for the location of the buried metal pipeline have become mature,but detection and location technologies for the non-metallic pipelines are still developing.In this paper,current trends and future perspectives of detection and location of buried non-metallic pipelines are summarized.Initially,this paper reviews and analyzes electromagnetic induction technologies,electromagnetic wave technologies,and other physics-based technologies.It then focuses on acoustic detection and location technologies,and finally introduces emerging technologies.Then the technical characteristics of each detection and location method have been compared,with their strengths and weaknesses identified.The current trends and future perspectives of each buried non-metallic pipeline detection and location technology have also been defined.Finally,some suggestions for the future development of buried non-metallic pipeline detection and location technologies are provided.

A presumed iridocyclitis developed to panophthalmitis caused by a non-metallic intraocular foreign body

Dear Editor,I write to present one case report of a patient suffered the panophthalmitis caused by non-metallic foreign body with no etiologic agent and recovered quickly by phacoemulsification and vitrectomy with silicone oil tamponade.Ocular trauma remains a major cause of blindness, particularly in the working-age population.

Three-dimensional analysis technology for accurately characterizing non-metallic inclusion particles in steel

In this paper, a kind of three-dimensional analysis technology for characterizing non-metallic inclusions in steel was clearly elaborated. It is an electron microscopy observation, namely the non-aqueous electrolysis extraction method with a settled coulometer. In the research,the extraction effects of non-metallic inclusions in different electrolysis systems were studied, and it was concluded that alkalescent 2% TEA non-aqueous electrolyte was applicable for extracting most of non-metallic inclusion particles in steel. And then, in order to ensure the microscopic characterization and statistical calculation of inclusion particles, some electrolysis parameters should be confirmed, such as the size of the sample, control of the electrolysis mass, electric current, etc. Furthermore, for preventing the disturbance of carbides and presenting clear three-dimensional appearance by microscopic characterization, magnetic separation was utilized to separate the inclusion particles from carbides, which was useful for getting more veracious types, particle sizes and chemical composition of inclusions. Moreover, through calculation of quantity and particle size of inclusions in continuous determinate fields, the total quantity per unit volume or area and the particle size distribution of inclusions could be acquired by conversion with electrolysis loss. Besides, the comparison between this method and traditional quantitative metallography was also discussed, and finally, a conclusion was drawn that both of them have respectively applications in characterizing inclusions.

Effect of Methanol in the Wash-Solvent Bottle and the OnGuard Cartridges on the Determination of Different Anions Using Ion Chromatography

The effect of using methanol in the flush-solvent bottle of the auto-sampler of Ion Chromatograph on the determination of sulfate ions was studied using AS11-HC 2 mm analytical column. The use of 50% methanol in the flush solvent bottle results in overestimation of sulfate concentration by 18%. However, the use of 10% methanol instead of 50% did not show such error in the determination of sulfate using the same column. Furthermore, the effect of using OnGuard-RP and OnGuard-P cartridges for sample pretreatment on the determination of different anions was also studies using AS14-HC 2 mm analytical column. The results indicate that using OnGuard-RP cartridge caused the concentration of fluoride, bromide, nitrate, phosphate and sulfate ions to be underestimated, whereas the concentration of chloride ions to be overestimated. The error in the determination of fluoride, bromide, nitrate, phosphate sulfate, and chloride was found to be 40.0%, 26.0%, 22.8%, 26.8%, 18.0%, and 25.0% of the certified standard concentration, respectively. It was also found that the use of OnGuard-P cartridge resulted in underestimation of fluoride, chloride, bromide, nitrate, phosphate, and sulfate by 60.0%, 40.0%, 82.0%, 87.2%, 45.2%, and 39.0% of the certified standard concentration, respectively. These findings point out to careful corrections that should be considered in any application of ion chromatography utilizing such sample pretreatment.

Non-metallic Inclusions in Continuously Cast Aluminum Killed Steels

In aluminum killed steels, the size, shape, quantity and formation of non-metallic inclusions in ladle steel (before and after RH vacuum treatment) and in tundish as well as in slabs were studied by EPMA (Electron Probe Microanalysis) and by analyzing the total oxygen. The results showed that in the slabs the total oxygen was quite low and the inclusions discovered were mainly small-sized angular alumina inclusions. This indicates that most inclusions have been removed by floating out during the continuous casting process. In addition, the countermeasures were discussed to decrease the alumina inclusions in the slabs further.

Evaluation of Characteristics of Non-Metallic Inclusions in P/M Ni-Base Superalloy by Automatic Image Analysis

Non-metallic inclusions,especially the large ones,within P/M Ni-base superalloy have a major influence on fatigue characteristics,but are not directly measurable by routine inspection.In this paper,a method,automatic image analysis,is proposed for estimation of the content,size and amount of non-metallic inclusions in superalloy.The methodology for the practical application of this method is described and the factors affecting the precision of the estimation are discussed.In the experiment,the characteristics of the non-metallic inclusions in Ni-base P/M superalloy are analyzed.

The extending length calculation of hydraulic drive non-metallic completion screen pipe running into ultra-short radius horizontal well

Focusing on the extending length restriction of the completion screen pipe resistance running into ultra-short radius horizontal well,this paper proposed technology of hydraulic drive completion tubular string running into ultra-short radius horizontal well.Innovative hydraulic drive tools and string structure are designed,which are composed of guide tubing,hydraulic drive tubing and non-metallic completion screen pipe from inside to outside.A novel mechanical-hydraulic coupling model is established.Based on the wellbore structure of an ultra-short radius horizontal well for deep coalbed methane,the numerical calculations of force and hydraulic load on tubular strings were accomplished by the mechanical-hydraulic coupling model.The results show that the extending length of completion tubular string with the hydraulic drive is 17 times that of conventional completion technology under the same conditions.The multi-factor orthogonal design is adopted to analyze the numerical calculations,and the results show that the extending length of the completion tubular string is mainly affected by the completion tubular string structure and the friction coefficient between the non-metallic composite continuous screen pipe and the wellbore.Two series of hydraulic drive completion tubular string structures suitable for ultra-short radius horizontal wells under different conditions are optimized,with the extending limits of 381 m and 655 m,respectively.These researches will provide theoretical guidance for design and control of hydraulic drive non-metallic composite continuous completion screen pipe running into ultra-short radius horizontal wells.

Behavior of Non-metallic Inclusions in Centrifugal Induction Electroslag Castings

In order to know the behavior of non-metallic inclusions in centrifugal induction electroslag castings (CIESC), non-metallic inclusions in 5CrMnMo and 4Cr5MoSiV1 were qualitatively and quantitatively analyzed. The largest size of inclusions in the casting and the thermodynamic possibility of TiN precipitation in steel were also calculated. The results show that sulfide inclusions are evenly distributed and the content is low. The amount of oxide inclusions in CIESC: 4Cr5MoSiV1 steel is close to the ESR steel and lower than that in the EAF steel, and there are some differences along radial direction. Nitride inclusions are fine and the diameter of the largest one is 3-1 mum. With the increase of the centrifugal machine's rotational speed, the ratio of round inclusions increases and the ratio of sharp inclusions decreases. According to the experiment and the calculation results, it is pointed out that the largest diameter of non-metallic inclusions in the CIESC 4Cr5MoSiV1 casting is only 6.6 mum, and [N%][Ti%] in 4Cr5MoSiV1 steel should be controlled less than 4.4x 10(-5) in order to further reduce the amount and size of TiN inclusions.

Studies of non-metallic organic disinfectants on inactivation of avian influenza viruses

Six different kinds of non-metallic or organic disinfectants were obtained in this research study including “Neutral Electrolyzed Water”, “M22” organic disinfectant solution, Superoxy Food Wash disinfectant, Hydrogen Peroxide, Clorox Germicidal Bleach and Clidox-S. The effectiveness of these disinfectants was studied against various subtypes of avian influenza virus (AIV). The virus-disinfectant mixtures were prepared in serial dilutions of each disinfectant with a constant virus titer and incubated at ambient temperature in different time intervals for virus inactivation. The virus inactivation results were determined by virus recovery in embryonating chicken eggs. Among the six different kinds of nonmetallic disinfectants obtained for this research project, Neutral Electrolyzed Water, “M22” solution, Clorox Germicidal Bleach and Clidox-S were effectively inactivated AIV with appropriate working dilutions and reaction times. Superoxy Food Wash disinfectant and Hydrogen Peroxide were found having limited effect on virus inactivation with extended exposure times of more than 2 hours. These research findings provide scientific data to poultry industry with guidelines to select and use non-metallic organic disinfectants for poultry flock sanitation and disinfection to effectively prevent and control of avian influenza outbreaks.

Anomalous metastable hcp Ni nanocatalyst induced by non-metal N doping enables promoted ammonia borane dehydrogenation

Developing high-performing non-noble transition metal catalysts for H_(2) evolution from chemical hydrogen storage materials is of great significance for the hydrogen economy system, yet challenging. Herein,we present for the first time that anomalous metastable hexagonal close-packed Ni nanoparticles induced by heteroatom N doping encapsulated in carbon(N-hcp-Ni/C) can exhibit admirable catalytic performance for ammonia borane(AB) dehydrogenation, prominently outperforming conventional fcc Ni counterpart with similar morphology and favorably presenting the state-of-the-art level.Comprehensive experimental and theoretical studies unravel that unusual hcp phase engineering of Ni together with N doping could induce charge redistribution and modulate electronic structure, thereby facilitating H_(2)O adsorption and expediting H_(2)O dissociation(rate-determining step). As a result, AB dehydrogenation can be substantially boosted with the assistance of N-hcp-Ni/C. Our proposed strategy highlights that unconventional crystal phase engineering coupled with non-metal heteroatom doping is a promising avenue to construct advanced transition metal catalysts for future renewable energy technologies.

Charging of Materials Non-Metallic Used in Underground Mines Endangered by Firedamp and/or Coal Dust

The expansion parts and components of non-metallic in devices have become a fait accompli. In the case parts, components of non-metallic are used in atmospheres explosive and may be a potential source of ignition [1]. Ignition hazards due to static electricity from the charged non-conductive non-metallic materials are well known [2]. The prevalence protection metal parts and components of anti-corrosion exist in any device equipped with a metal casing. Inherent risks associated services are caused by static electricity. Electrostatic phenomena arise in many situations, in a variety of environments and industries. The occurrence of charge static in many cases unexpected is unwanted and requires the use of expensive preventive measures. Brush discharge and propagating brush discharge (e.g. composite coating about non-conductive electrostatic properties of an isolated base conductive) create explosion hazard in underground endangered by firedamp and/or coal dust [3].

正负脉冲电压驱动的电磁螺纹插装阀动态特性分析

提出了一种基于PWM技术的正负脉冲电压控制策略,用于提高锥阀式电磁螺纹插装阀启闭动态响应速度,使其满足数字液压技术的要求。在分析电磁螺纹插装阀结构和工作原理基础上,建立了电磁螺纹插装阀的数学模型,并在AMESim软件中搭建电磁螺纹插装阀及其测试系统的多物理场耦合建模,研究不同正负脉冲电压持续时间条件下电磁螺纹插装阀线圈电流、阀芯位移、电磁力的变化规律,确定了电磁螺纹插装阀响应速度最快时正负脉冲电压控制策略的最优控制参数。利用半实物仿真系统搭建SCV硬件在环测试实验台,对所提正负脉冲控制策略进行验证。实验表明,与常规电压控制策略相比,当正负脉冲电压控制策略中正负脉冲电压持续时间都为10 ms时,电磁螺纹插装阀的开启时间由30 ms缩短到13.5 ms,其关闭时间由139 ms缩短到14 ms。研究结果为电磁螺纹插装阀的高响应化和数字液压技术的发展提供参考。

4个红心猕猴桃品种果实品质及氨基酸代谢研究

以4个红心猕猴桃品种(金红50、脐红、红阳及金红)为供试材料,通过物候期调查,果实品质、糖组分及氨基酸含量测定,研究果实品质及氨基酸代谢差异。结果表明,4个红心猕猴桃品种中,红阳果实成熟期相对较早,金红50和脐红果实成熟期相对较晚。金红50单果质量最大,脐红果实可溶性固形物含量、总酸含量及干物质含量最高,金红果实固酸比最高。红阳果实赖氨酸、缬氨酸、亮氨酸、苯丙氨酸、苏氨酸、精氨酸、组氨酸、天冬氨酸、谷氨酸含量及氨基酸总量最高。该研究对红心猕猴桃果实品质及氨基酸代谢进行探究,可为本地区种植户种植选择、猕猴桃产业发展提供参考。

桁架式自动插装机器人控制系统设计

为了解决人工插装电子元件存在的效率及合格率低等问题,面向中小型3C企业的低成本桁架式线路板插装机器的控制系统开发,以电容插装为例,完成系统的上料、拾取、检测和插件等控制过程的设计,利用数据库完成插装关键信息的存储。系统采用通讯方式完成桁架式机器人的运动控制,具有控制灵活、成本低的优点;利用光电检测技术完成电容引脚距离检测、利用扭矩检测完成电容插入状态的判断,具有时间短、效率高的优点。系统经过实验测试,各项指标均满足设计要求。

不同特性粉尘对滤筒有效脉冲清灰压力的影响研究

为改善不同特性粉尘的清灰问题,选取3种不同黏性、不同粒径的粉尘,开展工业覆粉实验以探究除尘器的运行阻力和滤筒清灰效果的变化。研究结果表明:粉煤灰的最低清灰压力达到748 Pa,即可实现有效清灰;对于黏性粉尘,粉尘粒径对清灰的影响更显著,细粉尘对应的系统压降和粉尘残余体积量明显高于粗粉尘,中等黏性的MgO粉体最低有效清灰压力需要达到1 425 Pa,超细MgO则需要更高;高黏性的CMC-Na粉体对应的系统压降、压降平稳时间和粉尘残余体积量都明显高于其他粉体,其有效清灰压力需要至少达到1 657 Pa,除尘系统才能长时间运行。研究结果可为工业应用收集不同特性粉尘提供理论参考。

Effect of hafnium and molybdenum addition on inclusion characteristics in Co-based dual-phase high-entropy alloys

Specific grades of high-entropy alloys(HEAs)can provide opportunities for optimizing properties toward high-temperature applications.In this work,the Co-based HEA with a chemical composition of Co_(47.5)Cr_(30)Fe_(7.5)Mn_(7.5)Ni_(7.5)(at%)was chosen.The refractory metallic elements hafnium(Hf)and molybdenum(Mo)were added in small amounts(1.5at%)because of their well-known positive effects on high-temperature properties.Inclusion characteristics were comprehensively explored by using a two-dimensional cross-sectional method and extracted by using a three-dimensional electrolytic extraction method.The results revealed that the addition of Hf can reduce Al_(2)O_(3)inclusions and lead to the formation of more stable Hf-rich inclusions as the main phase.Mo addition cannot influence the inclusion type but could influence the inclusion characteristics by affecting the physical parameters of the HEA melt.The calculated coagulation coefficient and collision rate of Al_(2)O_(3)inclusions were higher than those of HfO_(2)inclusions,but the inclusion amount played a larger role in the agglomeration behavior of HfO_(2)and Al_(2)O_(3)inclusions.The impurity level and active elements in HEAs were the crucial factors affecting inclusion formation.