Effect of ball milling time on the microstructure and compressive properties of the Fe–Mn–Al porous steel

In the present work,Fe–Mn–Al–C powder mixtures were manufactured by elemental powders with different ball milling time,and the porous high-Mn and high-Al steel was fabricated by powder sintering.The results indicated that the powder size significantly decreased,and the morphology of the Fe powder tended to be increasingly flat as the milling time increased.However,the prolonged milling duration had limited impact on the phase transition of the powder mixture.The main phases of all the samples sintered at 640℃ were α-Fe,α-Mn and Al,and a small amount of Fe2Al5 and Al8Mn5.When the sintering temperature increased to 1200℃,the phase composition was mainly comprised of γ-Fe and α-Fe.The weight loss fraction of the sintered sample decreased with milling time,i.e.,8.3wt% after 20 h milling compared to15.3wt% for 10 h.The Mn depletion region(MDR) for the 10,15,and 20 h milled samples was about 780,600,and 370 μm,respectively.The total porosity of samples sintered at 640℃ decreased from ~46.6vol% for the 10 h milled powder to ~44.2vol% for 20 h milled powder.After sintering at 1200℃,the total porosity of sintered samples prepared by 10 and 20 h milled powder was ~58.3vol% and ~51.3vol%,respectively.The compressive strength and ductility of the 1200℃ sintered porous steel increased as the milling time increased.

Effect of Holding Time on the Microstructure and Mechanical Properties of Dual-Phase Steel during Intercritical Annealing

Continuous annealing simulation tests were conducted by using a continuous annealing thermomechanical simulator. Holding times of 5, 60, 180, and 480 seconds for an intercritical annealing temperature of 820℃ were adopted to investigate the evolution of the mierostructure and mechanical properties of ferrite-bainite dual-phase steel. The ferrite-bainite dual-phase steel was characterized by high strength and low yield ratio due to the presence of the constituents （polygonal ferrite, bainite, martensite and retained austenite） of the steel microstructure. Specimen 3 exhibits the highest value of A50 （7.67%） and a product of Rm × A50 （10453MPa%） after a 180s holding. This is likely attributed to the presence of a C-enriched retained anstenite in the microstructure. And the effect of martensite islands and carbide precipitate is thought to be able to contribute in strengthening the present steel. It is expected that equilibrium of anstenite fraction would be reached for reasonable intercritical holding period, regardless of the heating temperature. The results suggest that long increasing holding times may not be needed because the major phase of the microstructure does not change very significantly. It is favorable for industrial production of DP steels to shorten holding times. Key words： ferrite-bainite dual-phase steel; holding time; martensite islands; mechanical properties

Size,shape,charge and“stealthy”surface:Carrier properties affect the drug circulation time in vivo

The present review sets out to discuss recent developments of the effects and mechanisms of carrier properties on their circulation time.For most drugs,sufficient in vivo circulation time is the basis of high bioavailability.Drug carrier plays an irreplaceable role in helping drug avoid being quickly recognized and cleared by mononuclear phagocyte system,to give drug enough time to arrive at targeted organ and tissue to play its therapeutic effect.The physical and chemical properties of drug carriers,such as size,shape,surface charge and surface modification,would affect their in vivo circulation time,metabolic behavior and biodistribution.The final circulation time of carriers is determined by the balance between macrophage recognitions,blood vessel penetration and urine excretion.Therefore,when designing the drug delivery system,we should pay much attention to the properties of drug carriers to get enough in vivo circulation time to arrive at target site eventually.This article mainly reviews the effect of carrier size,size,surface charge and surface properties on its circulation time in vivo,and discusses the mechanism of these properties affecting circulation time.This review has reference significance for the research of long-circulation drug delivery system.

Influence of Sintering Time on Mechanical Properties of Ti-6Al-4V Compacts by Metal Injection Molding

Ti-6Al-4V compacts were fabricated by metal injection molding (MIM). Influence of vacuum sintering time on mechanical properties of the sintered compacts at 1260℃were investigated. The experimental results show that the compacts sintered at 1 260℃ for 3 hours～6 hours, which was made from hydrogenation-dehydrogenation(HDH) powder(averageparticles size is 45 μm), had a relative density of 95.6%～ 96.7%, ultimate tensile strength (648 MPa～686 MPa) and 0.2% yield strength (526 MPa～615 MPa) but a lower elongation (<4%) and that the compacts sintered at 1 260℃ for 2 hours～6 hours, which was made from 90wt% gas-atomized powder(average particles size is 32.5 μm) and 10 wt% HDH powder, had higher relative density (>95%),ultimate tensile strength (800 MPa～848 MPa), 0.2% yield strength (712 MPa～762 MPa) and high elongation (7.4%～9.5%).The mechanical properties of mixed powder specimens were nearly equivalent to the ASTM for the PM compacts.

Effect of HIPing time on the properties of TiAl alloys

The compacted TiAl alloys were prepared and the effects of HIPing time on their properties were studied. At 1100 ℃, 80 Mpa, the density of TiAl alloy reached up to 3.46 g/cm3 after 10 min HIPing. The densities of TiAl alloys did not significantly increase with the time increasing from 10 min to 70 min. Under the experimental conditions, the TiAl alloys obtained is an unstable state alloy, and the effect of HIPing time on the TiAl phase is not significant. The micro-cracks appear in inner of TiAl alloy with the HIPing time increase. At 1380 ℃, after one hour heat treatment, the micro-cracks disappear and the phase changes into stable state and its microstructure changs into lamella.

Effect of Reclamation Time and Land Use on Soil Properties in Changjiang River Estuary,China

The objective of this study is to analyze soil physical and chemical properties,soil comprehensive functions and impact factors after different years of reclamation.Based on the survey data taken from 216 soil sampling points in the Fengxian Reclamation Area of the Changjiang (Yangtze) River Estuary,China in April 2009 and remotely sensed TM data in 2006,while by virtue of multivariate analysis of variance (MANOVA),geo-statistical analysis (GA),prin-cipal component analysis (PCA) and canonical correspondence analysis (CCA),it was concluded that:1) With the in-crease in reclamation time,soil moisture,soil salinity,soil electric conductivity and soil particle size tended to decline,yet soil organic matter tended to increase.Soil available phosphorous tended to increase in the early reclamation period,yet it tended to decline after about 49 years of reclamation.Soil nitrate nitrogen,soil ammonia nitrogen and pH changed slightly in different reclamation years.Soil physical and chemical properties reached a steady state after about 30 years of reclamation.2) According to the results of PCA analysis,the weighted value (0.97 in total) that represents soil nutrient factors (soil nitrate nitrogen,soil organic matter,soil available phosphorous,soil ammonia nitrogen,pH and soil particle size) were higher than the weighted value (0.48 in total) of soil limiting factors (soil salinity,soil elec-tric conductivity and soil moisture).The higher the F value is,the better the soil quality is.3) Different land use types play different roles in the soil function maturity process,with farmlands providing the best contribution.4) Soil physi-cal and chemical properties in the reclamation area were mainly influenced by reclamation time,and then by land use types.The correlation (0.1905) of the composite index of soil function (F) with reclamation time was greater than that with land use types (-0.1161).

Effects of solution time on microstructure and mechanical properties of Ti-22Al-24Nb alloy

In this research, the changing rules of billet forged Ti-22 Al-24 Nb alloy with various solution time were studied, and the mechanical properties of different microstructure were tested at the room temperature. The results indicate that the(α2+O+B2) three-phase microstructure with equiaxed grains was acquired by Ti-22 Al-24 Nb alloy billet forging, and the average size of the grains was about 300 μm. With the increase of solution time, the primary lath-shaped O phase began to dissolve, and then the equiaxial α2 phase started to dissolve, but the undissolved α2/O phase began to be equiaxial and grow. The grains of original B2 phase recrystallized and grew. After the 2 h solution treatment, the recrystallization of grains was completed basically and the average size of the grains was about 100 μm. After the 2.5 h solution treatment, the strength of the alloy decreased, and the plasticity increased. However, when the solution treatment increased to 3 h, the plasticity decreased but the strength increased. The optimal solution parameters of Ti-22 Al-24 Nb alloy were the holding time of 2 h, the solution temperature of 1 000 ?C, and water cooling. Excellent comprehensive mechanical properties can be accquired under these parameters. The tensile strength, the yield strength, the elasticity modulus, the elongation, and the section shrinkage were 950 MPa, 915 MPa, 90 GPa, 15.69% and 42.28%, respectively.

Investigating the Use of <i>Jatropha</i>Biodiesel in Compression Ignition Engines by Comparing Effects of Storage Time on Its Properties with the Standard Properties of Fossil-Diesel and Properties of Quality Biodiesel

Effects of storage time on some properties of jatropha biodiesel were investigated over the storage time of 0 to 8 weeks at the temperature of 25℃. Such properties as water content and density were found to increase at the rates of 5 ppm and 14 kg/m3 per week respectively. These rates translate into property values which compare closely with the standard properties of fossil-diesel and properties of quality biodiesel. As a result, the jatropha biodiesel can be used as alternative fuel to fossil-diesel in compression ignition engines within 8 weeks of its production. However, the calorific value and flash point of the biodiesel decreased at the rate of 1.4℃ and 2.5 MJ/kg per week respectively. Although the flash point was within the acceptable level for quality biodiesel, the calorific values were abnormally higher than the values for quality biodiesel of about 38.7 MJ/kg. With the exception of the calorific values, the other properties were not reasonably affected.

Influence of soaking time on semi-conductivity and nonlinear electrical properties of TiO_2-based varistor ceramics

We investigated the influence of soaking time on the semi-conductivity and nonlinear electrical properties of TiO2-based varistor ceramic samples.We used a single sintering process and fabricated six disk samples of(Sr,Bi,Si,Ta)-doped TiO2-based varistor ceramics sintered at 1 250°C for 0.5 h,1.0 h,2.0 h,3.0 h,4.0 h,and 5.0 h,respectively.The samples were characterized by X-ray diffraction,breakdown voltage,and complex impedance.The results show that as the soaking time increases from 0.5 h to 5.0 h,the breakdown voltage drops before rising while the nonlinear coefficient increases and then decreases.We suggest that,considering both grain semi-conductivity and nonlinear electrical properties of the TiO2-based varistor ceramics,the optimal soaking time is between 2.0 h and 3.0 h.

Influence of Heating Time of Shea Nuts (vitellariaparadoxa) on Some Chemical Properties of Shea Butter

The experiment was conducted in the laboratories of the Departments of Chemistry and Animal Health and Production Technology, Adamawa State University, Mubi, Nigeria. The experiment was replicated three times in a Randomized Complete Block Design (RCBD) and consisted of six heating time 30, 60 and 120 minutes boiling, 30, 60 and 120 minutes roasting and one control. Data were collected on acid value, free fatty acid, iodine value, peroxide value, saponification value and unsaponifiable matter. The data collected were analyzed statistically using Generalized Linear Model (GLM) procedure of statistical analysis system (SAS). The means that were significantly different were separated using Least Significant Difference (LSD). The results showed that there were highly significant differences (P ≤ 0.01) among the treatments. The highest Acid Value (AV) of 3.53 and 3.64 were recorded by heating time at 120 minutes of boiling and 120 minutes of roasting. Heating time at 30 minutes of boiling, 30 minutes roasting, 60 minutes boiling and 60 minutes roasting recorded lower Free Fatty Acid (FFA) values of 1.52, 1.55, 1.57 and 1.58, respectively. Heating time at 60 minutes of roasting and 60 minutes of boiling recorded the highest Iodine value (IV) of 43.80 and 43.53, respectively. Based on the results of this study, it can be concluded that heating time of 30 or 60 minutes by boiling or roasting are better than longer heating times for Shea butter extraction.

The Effect of Ageing Time on Some Mechanical Properties of Aluminum/0.5% Glass Reinforced Particulate Composite

A particulate-hardened composite usually known as cermets with aluminum matrix and reinforced with ceramic particles from broken bottles was used to investigate the effect of ageing time on hardness and tensile strength. The samples used for the work were produced using stir-cast method and the samples were cast in metal moulds to improve on the surface finish and to obtain good cooling rate. The composite composition used was Al/0.5% glass particles. The samples were treated at 500?C and quenched in water at 65?C. They were then aged at various temperatures ranging from 150?C - 210?C. The result of the hardness test showed that within the range of the ageing time selected the hardness increased with the ageing for all the ageing temperatures used. Variations were observed but this is normal in ageing, particularly when coherent and incoherent precipitates are formed at a point in time, or when over-ageing occurs. The plot of the tensile strength tests and the hardness tests, with ageing time showed the trend as observed. The highest hardness value of 37.3 HRB occurred after 5 hours of ageing likewise the highest tensile strength value of 398.36 N/mm2 occurred after 5 hours of ageing at the same ageing temperature of 190?C. The aged composite showed improved hardness and tensile strength when compared to as-cast value of 23.7 HRB for hardness and 253.12 N/mm2 for tensile strength respectively.

Influence of quench transfer time on microstructure and mechanical properties of 7055 aluminum alloy

The influence of quench transfer time on the microstructure and mechanical properties of 7055 aluminum alloy with and without zirconium was investigated by tensile properties test,optical microscopy,scanning electron microscopy and transmission electron microscopy.For the Zr-free alloy,the strength increases to the highest value at 20 s with transfer time,and then decreases slightly.The elongation decreases slowly with transfer time within 20 s,and more rapidly after 20 s.For the Zr-containing alloy,prolonging transfer time within 20 s results in slight decrease in the strength and elongation,and rapid drop of which is observed after 20 s.For the Zr-free alloy,prolonging transfer time can increase the percentage of intergranular fracture,which is mainly caused by wide grain boundary precipitate free zone.The failure mode of the Zr-containing alloy is modified from the predominant transgranular void growth and intergranular fracture to transgranular shear and intergranular fracture with increase in the transfer time,which is attributed to the wider grain boundary precipitate free zone and coarse equilibrium η phases in the matrix.

Space-Time Properties as Quantum Effects. Restrictions Imposed by Grothendieck’s Scheme Theory

In this paper we consider properties of the four-dimensional space-time manifold M caused by the proposition that, according to the scheme theory, the manifold M is locally isomorphic to the spectrum of the algebra A, M &cong;Spec (A), where A is the commutative algebra of distributions of quantum-field densities. Points of the manifold M are defined as maximal ideals of density distributions. In order to determine the algebra A, it is necessary to define multiplication on densities and to eliminate those densities, which cannot be multiplied. This leads to essential restrictions imposed on densities and on space-time properties. It is found that the only possible case, when the commutative algebra A exists, is the case, when the quantum fields are in the space-time manifold M with the structure group SO (3, 1) (Lorentz group). The algebra A consists of distributions of densities with singularities in the closed future light cone subset. On account of the local isomorphism M &cong;Spec (A) , the quantum fields exist only in the space-time manifold with the one-dimensional arrow of time. In the fermion sector the restrictions caused by the possibility to define the multiplication on the densities of spinor fields can explain the chirality violation. It is found that for bosons in the Higgs sector the charge conjugation symmetry violation on the densities of states can be observed. This symmetry violation can explain the matter-antimatter imbalance. It is found that in theoretical models with non-abelian gauge fields instanton distributions are impossible and tunneling effects between different topological vacua | n> do not occur. Diagram expansion with respect to the -algebra variables is considered.

Comparison of time-related electrical properties of PN junctions and Schottky diodes for Zn O-based betavoltaic batteries

Schottky diodes and PN junctions were utilized as energy converting structures in ZnO-based betavoltaic batteries,in which 0.101121 Ci 63Ni was selected as the beta source.The time-related electrical properties were obtained using Monte Carlo simulations.For the n-type ZnO,the Pt/ZnO Schottky diode had the highest energy conversion efficiency,and the Ni/ZnO Schottky diode had the largest Isc.The overall electrical performance of PN junctions is better than that of Schottky diodes.The lifetimes of Pt/ZnO and Ni/ZnO are longer than for other Schottky devices,coming close to those of PN junctions.Considering that Schottky diodes are easier to fabricate and independent of p-type semiconductors,Pt/ZnO and Ni/ZnO diodes offer alternatives to PN-junction-based betavoltaic batteries.

Effect of Glutathione and Storage Time on Rheological Properties of Per-proofed Frozen Dough

The effect of reduced glutathione (GSH) on fresh and pre-proofed frozen dough rheological properties were investigated using dynamic stress rheometry and small scale extensibility with the addition of three levels (80×10-6, 160× 10-6 and 240×10-6 GSH) and six storage times (0 and 1 day, 2, 4, 6 and 8 weeks). Three relaxation times (1, 13 and 26min) after loading the dough in the rheometer were used to determine storage (G’) and loss (G”) moduli. Correlations for G’ (r=0.678 and 0.622 at 0.05, and 10Hz, respectively) and G” (r=0.699, and 0.690 at 0.05, and 10Hz, respectively) were observed with the area under the extension curve at 26 min relaxation time. The addition of GSH to fresh dough reduced G’ (16.4% to 55.9%) and G” (13.7% to 52.2%). Freezing and frozen storage caused increase in G’ and G”. The addition of GSH reduced dough strength indicated by the reduction in maximum resistance to extension (Rmax) and the ratio of maximum resistance to extensibility (Rmax/E). The reduction in Rmax across all relaxation times ranged from 16.2% to 59.4%. An increase in dough extension (E) was observed with 240×10-6 GSH at all frozen storage and rest period times. Addition of GSH caused an increase of liquid phase (30.6% to 35.3%) in fresh dough and frozen dough (10.3% to 20.7%) after one day frozen storage. Negative correlations of water content in the solid phase with dough extensibility and area under the extensibility curve were found (r=-0.594 and-0.563, respectively, p<0.001). This suggests a loss of dough extensibility and strength as the water holding capacity of the dough components changes during frozen storage.

Effect of Glutinous Rice Flour on Mechanical Properties and Microstructure of Cement-based Materials

The mechanism of glutinous rice flour,a kind of natural admixture,on the hydration process,setting time,and microstructure of the Portland cement was investigated.The experimental results show that the glutinous rice flour has an obvious setting retarding effect on cement pastes.The optimal dosage of the glutinous rice flour is 3wt%.In this case,the initial and final setting time of the paste are delayed by 140 and185 min,respectively.The flexural and compressive strengths of the hardened paste are increased by 0.35%and 0.07%after 56 d of curing.The glutinous rice flour hinders the mineral dissolution process and decreases the concentration of calcium ion at the initial stage of hydration due to the complexation effect,thereby hindering the nucleation and growth of CH and C-S-H phases and prolonging the hydration process.However,C-S-H phases combine with the glutinous rice flour to contribute the bonding effect together,which compacts the microstructure of hardened cement pastes at the later hydration stage of cement pastes.Thus,in-depth investigation on the utilization of glutinous rice flour as the admixture for the Portland cement is expected to be meaningful for the control of hydration exothermic rate and setting time.

Deep learning for predictive mechanical properties of hot-rolled strip in complex manufacturing systems

Higher requirements for the accuracy of relevant models are put throughout the transformation and upgrade of the iron and steel sector to intelligent production.It has been difficult to meet the needs of the field with the usual prediction model of mechanical properties of hotrolled strip.Insufficient data and difficult parameter adjustment limit deep learning models based on multi-layer networks in practical applications;besides,the limited discrete process parameters used make it impossible to effectively depict the actual strip processing process.In order to solve these problems,this research proposed a new sampling approach for mechanical characteristics input data of hot-rolled strip based on the multi-grained cascade forest(gcForest)framework.According to the characteristics of complex process flow and abnormal sensitivity of process path and parameters to product quality in the hot-rolled strip production,a three-dimensional continuous time series process data sampling method based on time-temperature-deformation was designed.The basic information of strip steel(chemical composition and typical process parameters)is fused with the local process information collected by multi-grained scanning,so that the next link’s input has both local and global features.Furthermore,in the multi-grained scanning structure,a sub sampling scheme with a variable window was designed,so that input data with different dimensions can get output characteristics of the same dimension after passing through the multi-grained scanning structure,allowing the cascade forest structure to be trained normally.Finally,actual production data of three steel grades was used to conduct the experimental evaluation.The results revealed that the gcForest-based mechanical property prediction model outperforms the competition in terms of comprehensive performance,ease of parameter adjustment,and ability to sustain high prediction accuracy with fewer samples.

Luminescent properties dependence of water-soluble CdTe quantum dots on stabilizing agents and reaction time

The influence of stabilizing agents and reaction time on the luminescent properties of water-soluble CdTe quantum dots(QDs) was discussed.The thioglycolic acid(TGA)-CdTe ODs were characterized by TEM,XRD and FTIR.It is found that larger-size QDs can be synthesized more easily when L-cysteine(Cys) or golutathione(GSH) is chosen as stabilizing agent and TGA is proper to prepare highly luminescent QDs because of the effect between Cd2+ and sulfhydryl group.Furthermore,the absorption wavelength,full width at half maximum(FWHM),stokes shift,photoluminescence(PL) quantum yield and PL stability of TGA-CdTe are strongly dependent on reaction time,in which the absorption wavelength changes against reaction time with an exponential function.The TGA-CdTe QDs prepared at 2 h possess more excellent luminescent properties.

Theoretical Study on the Optical Properties for 2,7- and 3,6-Linked Carbazole Trimers by Time-dependent Density Functional Theory

Electronic properties, such as HOMO and LUMO energies, band gaps, ionization potential （IP） and electron affinity （EA） of 2,7- and 3,6-1inked carbazole trimers, two conjugated oligomcrs with different linkages of carbazole, were studicd by the density functional theory with Becke-Lee-Young-Parr composite exchange correlation functional （B3LYP）. The absorption spectra of these compounds were also investigated by time-dependent density functional theory （TD-DFT） with 6-3 IG＊ basis set. The calculated results indicated that the HOMO and LUMO of the 2,7- and 3,6-1inked carbazole trimers are both slightly destabilized on going from methyl substitution to sec-butyl substitution. Both IP and EA exhibit their good hole-transporting but poor electronaccepting ability. The presence of alkyl groups on the nitrogen atoms does not affect the intra-chain electronic delocalization along the molecular frame. Thus no significant effect on the band gap and absorption spectra of compounds has been found.

New Neumerical Method to Calculate Time-Dependent Quantum Properties in Finite Temperature Based on the Heisenberg Equation of Motion

For the purpose of computer calculation to evaluate time-dependent quantum properties in finite temperature, we propose new numerical method expressed in the forms of simultaneous differential equations. At first we derive the equation of motion in finite temperature, which is found to be same expression as Heisenberg equation of motion except for the c-number. Based on this equation, we construct numerical method to estimate time-dependent physical properties in finite temperature precisely without using analytical procedures such as Keldysh formalism. Since our approach is so simple and is based on the simultaneous differential equations including no terms related to self-energies, computer programming can be easily performed. It is possible to estimate exact time-dependent physical properties, providing that Hamiltonian of the system is taken to be a one-electron picture. Furthermore, we refer to the application to the many body problem and it is numerically possible to calculate physical properties using Hartree Fock approximation. Our numerical method can be applied to the case even when perturbative Hamiltonians are newly introduced or Hamiltonian shows complex time-dependent behavior. In this article, at first, we derive the equation of motion in finite temperature. Secondly, for the purpose of verification and of exhibiting the usefulness, we show the derivation of gap equation of superconductivity and of sum rule of electrical conductivity and the application to the many body problem. Finally we apply this method to these two cases: the first case is most simplified resonance charge transfer neutralization of an ion and the second is the same process but impurity potential is newly introduced as perturbative Hamiltonian. Through both cases, it is found that neutralization process is not so sensitive to temperature, however, impurity potential as small as 10 meV strongly influences the neutralization of ion.