A review on the cooling of energy conversion and storage systems using thermoelectric modules

Exploitation of sustainable energy sources requires the use of unique conversion and storage systems,such as solar panels,batteries,fuel cells,and electronic equipment.Thermal load management of these energy conversion and storage systems is one of their challenges and concerns.In this article,the thermal management of these systems using thermoelectric modules is reviewed.The results show that by choosing the right option to remove heat from the hot side of the thermoelectric modules,it will be a suitable local cooling,and the thermoelectric modules increase the power and lifespan of the system by reducing the spot temperature.Thermoelectric modules were effective in reducing panel temperature.They increase the time to reach a temperature above 50℃ in batteries by 3 to 4 times.Also,in their integration with fuel cells,they increase the power density of the fuel cell.

Efficient and Stable Inverted Perovskite Solar Modules Enabled by Solid-Liquid Two-Step Film Formation

A considerable efficiency gap exists between large-area perovskite solar modules and small-area perovskite solar cells.The control of forming uniform and large-area film and perovskite crystallization is still the main obstacle restricting the efficiency of PSMs.In this work,we adopted a solid-liquid two-step film formation technique,which involved the evaporation of a lead iodide film and blade coating of an organic ammonium halide solution to prepare perovskite films.This method possesses the advantages of integrating vapor deposition and solution methods,which could apply to substrates with different roughness and avoid using toxic solvents to achieve a more uniform,large-area perovskite film.Furthermore,modification of the NiO_(x)/perovskite buried interface and introduction of Urea additives were utilized to reduce interface recombination and regulate perovskite crystallization.As a result,a large-area perovskite film possessing larger grains,fewer pinholes,and reduced defects could be achieved.The inverted PSM with an active area of 61.56 cm^(2)(10×10 cm^(2)substrate)achieved a champion power conversion efficiency of 20.56%and significantly improved stability.This method suggests an innovative approach to resolving the uniformity issue associated with large-area film fabrication.

Highly Efficient and Stable FAPbI_(3) Perovskite Solar Cells and Modules Based on Exposure of the(011)Facet

Perovskite crystal facets greatly impact the performance and stability of their corresponding photovoltaic devices.Compared to the(001)facet,the(011)facet yields better photoelectric properties,including higher conductivity and enhanced charge carrier mobility.Thus,achieving(011)facet-exposed films is a promising way to improve device performance.However,the growth of(011)facets is energetically unfavorable in FAPbI_(3) perovskites due to the influence of methylammonium chloride additive.Here,1-butyl-4-methylpyridinium chloride([4MBP]Cl)was used to expose(011)facets.The[4MBP]^(+)cation selectively decreases the surface energy of the(011)facet enabling the growth of the(011)plane.The[4MBP]^(+)cation causes the perovskite nuclei to rotate by 45°such that(011)crystal facets stack along the out-of-plane direction.The(011)facet has excellent charge transport properties and can achieve better-matched energy level alignment.In addition,[4MBP]Cl increases the activation energy barrier for ion migration,suppressing decomposition of the perovskite.As a result,a small-size device(0.06 cm2)and a module(29.0 cm2)based on exposure of the(011)facet achieved power conversion efficiencies of 25.24%and 21.12%,respectively.

Modulating J-V hysteresis of planar perovskite solar cells and mini-modules via work function engineering

Commercialization of perovskite solar cells(PSCs) requires the development of high-efficiency devices with none current density-voltage(J-V) hysteresis. Here, electron transport layers(ETLs) with gradual change in work function(WF) are successfully fabricated and employed as an ideal model to investigate the energy barriers, charge transfer and recombination kinetics at ETL/perovskite interface. The energy barrier for electron injection existing at ETL/perovskite is directly assessed by surface photovoltage microscopy, and the results demonstrate the tunable barriers have significant impact on the J-V hysteresis and performance of PSCs. By work function engineering of ETL, PSCs exhibit PCEs over 21% with negligible hysteresis. These results provide a critical understanding of the origin reason for hysteresis effect in planar PSCs, and clear reveal that the J-V hysteresis can be effectively suppressed by carefully tuning the interface features in PSCs. By extending this strategy to a modified formamidinium-cesium-rubidium(FA-Cs-Rb) perovskite system, the PCEs are further boosted to 24.18%. Moreover, 5 cm × 5 cm perovskite mini-modules are also fabricated with an impressive efficiency of 20.07%, demonstrating compatibility and effectiveness of our strategy on upscaled devices.

Solvent engineering towards scalable fabrication of high-quality perovskite films for efficient solar modules

Over the last decade,remarkable progress has been made in metal halide perovskite solar cells(PSCs),which have been a focus of emerging photovoltaic techniques and show great potential for commercialization.However,the upscaling of small-area PSCs to large-area solar modules to meet the demands of practical applications remains a significant challenge.The scalable production of high-quality perovskite films by a simple,reproducible process is crucial for resolving this issue.Furthermore,the crystallization behavior in the solution-processed fabrication of perovskite films can be strongly influenced by the physicochemical properties of the precursor inks,which are significantly affected by the employed solvents and their interactions with the solutes.Thus,a comprehensive understanding of solvent engineering for fabricating perovskite films over large areas is urgently required.In this paper,we first analyze the role of solvents in the solution-processed fabrication of large-area perovskite films based on the classical crystal nucleation and growth mechanism.Recent efforts in solvent engineering to improve the quality of perovskite films for solar modules are discussed.Finally,the basic principles and future challenges of solvent system design for scalable fabrication of high-quality perovskite films for efficient solar modules are proposed.

Crystallization and Orientation Modulation Enable Highly Efficient Doctor-Bladed Perovskite Solar Cells

With the rapid rise in perovskite solar cells(PSCs)performance,it is imperative to develop scalable fabrication techniques to accelerate potential commercialization.However,the power conversion efficiencies(PCEs)of PSCs fabricated via scalable two-step sequential deposition lag far behind the state-of-the-art spin-coated ones.Herein,the additive methylammonium chloride(MACl)is introduced to modulate the crystallization and orientation of a two-step sequential doctorbladed perovskite film in ambient conditions.MACl can significantly improve perovskite film quality and increase grain size and crystallinity,thus decreasing trap density and suppressing nonradiative recombination.Meanwhile,MACl also promotes the preferred face-up orientation of the(100)plane of perovskite film,which is more conducive to the transport and collection of carriers,thereby significantly improving the fill factor.As a result,a champion PCE of 23.14%and excellent longterm stability are achieved for PSCs based on the structure of ITO/SnO_(2)/FA_(1-x)MA_xPb(I_(1-y)Br_y)_3/Spiro-OMeTAD/Ag.The superior PCEs of 21.20%and 17.54%are achieved for 1.03 cm~2 PSC and 10.93 cm~2 mini-module,respectively.These results represent substantial progress in large-scale two-step sequential deposition of high-performance PSCs for practical applications.

Carbon-based perovskite solar cells: From single-junction to modules

Perovskite solar cells(PSCs)have attracted more and more attention in the scientific community due to their high performance and simple fabrication process.In the past few years,emerging technologies have made manufacturing large-scale PSC modules possible.However,stability and fabrication issues still limit the modularization and commercialization of PSCs.Carbon materials have been widely used in PSCs to overcome these challenges due to their excellent optical,electrical,and mechanical properties.In addition,the hydrophobic properties of certain carbon materials are highly effective at protecting the perovskite film from moisture and improving the stability of PSCs.All these superior properties have made carbon one of the most promising materials to fabricate future highperformance PSC modules with long service lifetimes.In this review,recent developments of carbon-based materials in different layers of single-junction PSCs will first be discussed,with an emphasis on functionalities related to PSCs’stability and modularization.Then,current improvements and future discussions in the manufacturing of monolithic PSC modules will be reviewed in detail.

Photovoltaic Cells and Modules towards Terawatt Era

Progresses in photovoltaic technologies over the past years are evident from the lower costs, the rising efficiency, to the great improvements in system reliability and yield. Cumulative installed power yearly growths were on an average more than 40% in the period from 2007 to 2016 and in 2016, the global cumulative photovoltaic power installed has reached 320 GWp. The level 0.5 TWp could be reached before 2020. The production processes in the solar industry still have great potential for optimization both wafer based and thin film technologies. Trends following from the present technology levels are discussed, also taking into account other parts of photovoltaic systems that influence the cost of electrical energy produced. Present developments in the three generations of photovoltaic modules are discussed along with the criteria for the selection of appropriate photovoltaic module manufacturing technologies. The wafer based crystalline silicon(csilicon) technologies have the role of workhorse of present photovoltaic power generation, representing more than 90% of total module production. Further technology improvements have to be implemented without significantly increasing costs per unit, despite the necessarily more complex manufacturing processes involved. The tandem of c-silicon and thin film cells is very promising. Durability may be a limiting factor of this technology due to the dependence of the produced electricity cost on the module service time.

Sodium Diffuses from Glass Substrates through P1 Lines and Passivates Defects in Perovskite Solar Modules

Most thin-film photovoltaic modules are constructed on soda-lime glass(SLG)substrates containing alkali oxides,such as Na_(2)O.Na may diffuse from SLG into a module's active layers through P1 lines,an area between a module's constituent cells where the substrate-side charge transport layer(CTL)is in direct contact with SLG.Na diffusion from SLG is known to cause several important effects inⅡ-Ⅵand chalcogenide solar modules,but it has not been studied in perovskite solar modules(PSMs).In this work,we use complementary microscopy and spectroscopy techniques to show that Na diffusion occurs in the fabrication process of PSMs.Na diffuses vertically inside P1 lines and then laterally from P1 lines into the active area for up to 360 pm.We propose that this process is driven by the high temperatures the devices are exposed to during CTL and perovskite annealing.The diffused Na preferentially binds with Br,forming Br-poor,l-rich perovskite and a species rich in Na and Br(Na-Br)close to P1 lines.Na-Br passivates defect sites,reducing non-radiative recombination in the perovskite and boosting its luminescence by up to 5×.Na-Br is observed to be stable after 12 weeks of device storage,suggesting long-lasting effects of Na diffusion.Our results not only point to a potential avenue to increase PSM performance but also highlight the possibility of unabated Na diffusion throughout a module's lifetime,especially if accelerated by the electric field and elevated temperatures achievable during device operation.

Role of PV-Powered Vehicles in Low-Carbon Society and Some Approaches of High-Efficiency Solar Cell Modules for Cars

Development of highly-efficient photovoltaic (PV) modules and expanding its application fields are significant for the further development of PV technologies and realization of innovative green energy infrastructure based on PV. Especially, development of solar-powered vehicles as a new application is highly desired and very important for this end. This paper presents the impact of PV cell/module conversion efficiency on reduction in CO2 emission and increase in driving range of the electric based vehicles. Our studies show that the utilization of a highly-efficient (higher than 30%) PV module enables the solar-powered vehicle to drive 30 km/day without charging in the case of light weight cars with electric mileage of 17 km/kWh under solar irradiation of 3.7 kWh/m2/day, which means that the majority of the family cars in Japan can run only by the sunlight without supplying fossil fuels. Thus, it is essential to develop high-efficiency as well as low-cost solar cells and modules for automotive applications. The analytical results developed by the authors for conversion efficiency potential of various solar cells for choosing candidates of the PV modules for automotive applications are shown. Then we overview the conversion efficiency potential and recent progress of various Si tandem solar cells, such as III-V/Si, II-VI/Si, chalcopyrite/Si, and perovskite/Si tandem solar cells. The III-V/Si tandem solar cells are expected to have a high potential for various applications because of its high conversion efficiency of larger than 36% for dual-junction and 42% for triple-junction solar cells under 1-sun AM1.5 G illumination, lightweight and low-cost potentials. The analysis shows that III-V based multi-junction and Si based tandem solar cells are considered to be promising candidates for the automotive application. Finally, we report recent results for our 28.2% efficiency and Sharp’s 33% mechanically stacked InGaP/GaAs/Si triple-junction solar cell. In addition, new approaches which are suitable for automotive applications by using III-V triple-junction, and static low concentrator PV modules are also presented.

Enhanced performance of solution-processed carbon nanotube transparent electrodes in foldable perovskite solar cells through vertical separation of binders by using eco-friendly parylene substrate

The successful utilization of an eco-friendly and biocompatible parylene-C substrate for high-performance solution-processed double-walled carbon nanotube(CNT)electrode-based perovskite solar cells(PSCs)was demonstrated.Through the use of a novel inversion transfer technique,vertical separation of the binders from the CNTs was induced,rendering a stronger p-doping effect and thereby a higher conductivity of the CNTs.The resulting foldable devices exhibited a power conversion efficiency of 18.11%,which is the highest reported among CNT transparent electrode-based PSCs to date,and withstood more than 10,000 folding cycles at a radius of 0.5 mm,demonstrating unprecedented mechanical stability.Furthermore,solar modules were fabricated using entirely laser scribing processes to assess the potential of the solution-processable nanocarbon electrode.Notably,this is the only one to be processed entirely by the laser scribing process and to be biocompatible as well as eco-friendly among the previously reported nonindium tin oxide-based perovskite solar modules.

Dye-sensitized solar cell module realized photovoltaic and photothermal highly efficient conversion via three-dimensional printing technology

Three-dimensional （3D） printing technology is employed to improve the photovoltaic and photothermal conversion efficiency of dye-sensitized solar cell （DSC） module. The 3D-printed concentrator is optically designed and improves the photovoltaic efficiency of the DSC module from 5.48% to 7.03%. Additionally, with the 3D-printed microfluidic device serving as water cooling, the temperature of the DSC can be effectively controlled, which is beneficial for keeping a high photovoltaic conversion efficiency for DSC module. Moreover, the 3D-printed microfluidic device can realize photothermal conversion with an instantaneous photothermal efficiency of 42.1%. The integrated device realizes a total photovoltaic and photothermal conversion efficiency of 49% at the optimal working condition.

Pulsed Modulation in Electro-Hyperthermia

Modulated electro-hyperthermia (mEHT) is one of the novel oncological treatments with many preclinical and clinical results showing its advantages. The basis of the method is the synergy of thermal and nonthermal effects, similar to the thermal action of conventional hyperthermia combined with ionizing radiation (radiotherapy). The electric field and the radiofrequency current produced both the thermal and nonthermal processes. The thermal effects produce the elevated temperature as a thermal background to optimize the nonthermal impacts. The low frequency amplitude modulation ensures accurate targeting and promotes immunogenic cell death to develop the tumor specific memory T cells disrupting the malignant cells by immune surveillance. This process (abscopal effect) works like a vaccination. The low frequency amplitude modulation is combined in the new method with the high power pulses for short time, increasing the tumor distortion ability of the electric field. The new modulation combination has much deeper penetration triplicating the active thickness of the effective treatment. The short pulse absorption increases the safety and decreases the thermal toxicity of the treatment, making the treatment safer. The increased power allows for reduced treatment time with the prescribed dose.

Organic additives in all-inorganic perovskite solar cells and modules:from moisture endurance to enhanced efficiency and operational stability

Power conversion efficiency(PCE) of perovskite solar cells(PSC) has been skyrocketed to certified 25.5% owing to their improved and tunable optoelectronic properties. Although, various strategies have been adopted to date regarding PCE and stability enhancement within PSC technology, certain instability factors(moisture, heat, light) are hindering their commercial placement. Recently, all-inorganic PSCs got hype in the photovoltaic research community after they attained PCE > 20% and due to their significant endurance against heat and light mishmashes, but there only left moisture sensitivity as the only roadblock for their industrial integration. Here, we review the recent progress of additive inclusion into allinorganic(CsPbX_(3)) PSCs to stabilize their intrinsic structure and to withstand the performance limiting factors. We start with the detailed description of chemical instability of different perovskite compositions, phase segregation, and how organic molecules and dyes help to repair the structural defects to improve the overall PCE and stability of PSCs. Moisture endurance as a result of chemical passivation through organic additives, low-dimensional inorganic PSCs to enhance device stability and scalable fabrication of CsPbX_(3) PSCs are also reviewed. The challenges of module degradation and design implications with proposed strategies and outlook are interpreted in the ending phrases of this review.

Harnessing aryl hydrocarbon receptor dynamics:Unveiling therapeutic pathways in esophageal squamous cell carcinoma

This editorial discusses the insightful minireview by Rahmati et al.The minireview delves into the role of the aryl hydrocarbon receptor in the development and progression of esophageal squamous cell carcinoma,highlighting its potential as a promising therapeutic target.The authors concisely summarize the current understanding of how aryl hydrocarbon receptor modula-tion influences immune responses and the tumor microenvironment,offering fresh perspectives on therapeutic strategies.This editorial aimed to emphasize the significance of these findings and their potential impact on future research and clinical practices for the management of esophageal squamous cell carcinoma.

Dynamic Performance of Fuel Cell Power Module for Mobility Applications

Fuel cell powered vehicles have been developed as another alternative to internal combustion engine powered vehicles for some applications including passenger cars, buses, trains, motorcycles, forklifts, electric wheelchairs, electric trolleybuses, medical carts, military engines, personal sports craft, mobility devices and other self propelled equipment. Up to now, many researches have focused on the development of the power module in the Fuel cell vehicles (FCVs) and the components of these systems such as membranes, bipolar plates, and electrodes. However, our work in this study focuses on operating the integrated fuel cell power module system efficiently for various operating conditions such as pressure, relative humidity and operating modes. In our validation we have utilized PEMFC single cell, with active area geometry 16 cm2 and of 120 cm2. Some results obtained in our study shown significant performance indicators for PEMFC stack (composed of 2 cells and 4 cells in a series) at different humidification levels.

Playdough-like carbon electrode: A promising strategy for high efficiency perovskite solar cells and modules

Carbon-based perovskite solar cells(C-PSCs)are promising candidates for large-scale photovoltaic applications due to their theoretical low cost and high stability.However,the fabrication of high-performance C-PSCs with large-area electrodes remains challenging.In this work,we propose a novel playdough-like graphite putty as top electrode in the perovskite devices.This electrode with soft nature can form good contact with the holetransporting layer and the conductive substrate at room temperature by a simple pressing technique,which facilitates the fabrication of both small-area devices and perovskite solar modules.In this preliminary research,the corresponding small devices and modules can achieve efficiencies of 20.29%(~0.15 cm^(2))and 16.01%(~10 cm^(2)),respectively.Moreover,we analyze the limitations of the optical and electrical properties of this playdough-like graphite electrode on the device performance,suggesting a direction for further improvement of C-PSCs in the future.

Probiotic modulation of dendritic cells co-cultured with intestinal epithelial cells

AIM： To investigate cytokine production and cell surface phenotypes of dendritic cells （DC） in the presence of epithelial cells stimulated by probiotics.METHODS： Mouse DC were cultured alone or together with mouse epithelial cell monolayers in normal or in- verted systems and were stimulated with heat-killed probiotic bacteria, Bifidobacterium lactis ADO 11 （BL）, Bifidobacterium bilfidum BGN4 （BB）, Lactobacillus casei IBS041 （LC）, and Lactobacillus acidophilus AD031 （LA）, for 12 h. Cytokine levels in the culture supernatants were determined by enzyme-linked immunosorbent as say and phenotypic analysis of DC was investigated by flow cytometry.RESULTS： BB and LC in singlecultured DC increased the expression of I-Ad, CD86 and CD40 （I-Ad, 18.51 vs 30.88, 46.11, CD86, 62.74 vs 92.7, 104.12; CD40, 0.67 vs 6.39, 3.37, P 〈 0.05）. All of the experimental probiot-ics increased the production of inflammatory cytokines, interleukin （IL）-6 and tumor necrosis factor （TNF）-α. However, in the normal coculture systems, LC and LA decreased the expression of I-A^α （39.46 vs 30.32, 33.26, P 〈 0.05）, and none of the experimental probiotics increased the levels of IL-6 or TNF-α. In the inverted coculture systems, LC decreased the expression of CD40 （1.36 vs -2.27, P 〈 0.05）, and all of the experimental probiotics decreased the levels of IL-6. In addition, BL increased the production of IL-10 （103.8 vs 166.0, P 〈 0.05） and LC and LA increased transforming growth factor-13 secretion （235.9 vs 618.9, 607.6, P 〈 0.05）.CONCLUSION： These results suggest that specific pro- biotic strains exert differential immune modulation mediated by the interaction of dendritic cells and epithelial cells in the homeostasis of gastrointestinal tract.

Tendon stem/progenitor cell ageing: Modulation and rejuvenation

Tendon ageing is a complicated process caused by multifaceted pathways and ageing plays a critical role in the occurrence and severity of tendon injury.The role of tendon stem/progenitor cells(TSPCs)in tendon maintenance and regeneration has received increasing attention in recent years.The decreased capacity of TSPCs in seniors contributes to impaired tendon functions and raises questions as to what extent these cells either affect,or cause ageing,and whether these age-related cellular alterations are caused by intrinsic factors or the cellular environment.In this review,recent discoveries concerning the biological characteristics of TSPCs and age-related changes in TSPCs,including the effects of cellular epigenetic alterations and the mechanisms involved in the ageing process,are analyzed.During the ageing process,TSPCs ageing might occur as a natural part of the tendon ageing,but could also result from decreased levels of growth factor,hormone deficits and changes in other related factors.Here,we discuss methods that might induce the rejuvenation of TSPC functions that are impaired during ageing,including moderate exercise,cell extracellular matrix condition,growth factors and hormones;these methods aim to rejuvenate the features of youthfulness with the ultimate goal of improving human health during ageing.

Rb1 protects endothelial cells from hydrogen peroxide-induced cell senescence by modulating redox status

Objectives Endothelial senescence has been proposed to be involved in endothelial dysfunction and atherogenesis. This study investigates the effects of ginsenoside Rbl, a major constituent of ginseng,on H2O2-induced endothelial senescence.Methods Primary human umbilical vein endothelial cells（HUVECs） senescence was induced by H2O2 as judged by senescence-associated P-galactosidase assay （SA-P-gal）.Fntracellur superoxide dismutase（S0D1） activity and malondialdehyde（MDA） level were determined by commercial kit.S0D1 mRNA and protein expression were analyzed by real time PCR and Western blot.Reactive oxygen species（ROS） were determined by flow cytometry.Results Rb1 was found to reverse endothelial senescence,as witnessed by a significant decrease of senescent cell numbers. Rbl could markedly increase intracellular SOD activity, decrease the MDA level,and suppress the generation of intracellular ROS in H2O2-treated HUVECs.Consistent with these findings,Rbl can effectively restore SOD1 mRNA and protein expression which decreased in H2O2 treated cells. Conclusions Our report demonstrates thatRbl can exert reversal effects on H2O2-induced cellular senescence through modulating cellular redox status.