Circular holes are commonly employed in engineering designs;however, they often serve as locations where cracks initiate and propagate. This paper explores a novel approach to structural repair by utilizing piezoelect...Circular holes are commonly employed in engineering designs;however, they often serve as locations where cracks initiate and propagate. This paper explores a novel approach to structural repair by utilizing piezoelectric actuators. The primary focus of this study is to investigate the influence of an adhesively bonded piezoelectric actuator patch placed above a circular hole on the stress intensity factor (SIF) in an aluminium plate. The plate is subjected to uniaxial tensile stress, while the piezoelectric actuator is excited with varying voltage levels. The analysis is conducted using the finite element method (FEM), a powerful numerical technique for simulating complex structures. The study assesses the stress distribution and employs the SIF as an adequate criterion for evaluating the impact of different patch configurations. The results indicate a strong correlation between the applied voltage and the SIF. Whether the SIF increases or decreases depends on the polarization of the piezoelectric actuator. Particularly noteworthy is the finding that rectangular patches in a horizontal orientation significantly reduce the SIF compared to other patch geometries. Moreover, double-sided patches exhibit a pronounced decrease in the SIF compared to single-sided patches. In summary, this research underscores the potential of piezoelectric actuators in mitigating stress intensity in structures with circular hole with crack initiation. It offers valuable insights into the influence of applied voltage, patch geometry, and patch placement on the SIF, thereby contributing to developing effective strategies for enhancing structural integrity.展开更多
This paper demonstrates the importance of three-dimensional(3-D)piezoelectric coupling in the electromechanical behavior of piezoelectric devices using three-dimensional finite element analyses based on weak and stron...This paper demonstrates the importance of three-dimensional(3-D)piezoelectric coupling in the electromechanical behavior of piezoelectric devices using three-dimensional finite element analyses based on weak and strong coupling models for a thin cantilevered piezoelectric bimorph actuator.It is found that there is a significant difference between the strong and weak coupling solutions given by coupling direct and inverse piezoelectric effects(i.e.,piezoelectric coupling effect).In addition,there is significant longitudinal bending caused by the constraint of the inverse piezoelectric effect in the width direction at the fixed end(i.e.,3-D effect).Hence,modeling of these effects or 3-D piezoelectric coupling modeling is an electromechanical basis for the piezoelectric devices,which contributes to the accurate prediction of their behavior.展开更多
Piezoelectric actuators are distributed on both side of a rectangular wing model,and the possibility of improvement of aircraft rolling power is investigated. The difference between the model with aileron deflection a...Piezoelectric actuators are distributed on both side of a rectangular wing model,and the possibility of improvement of aircraft rolling power is investigated. The difference between the model with aileron deflection and the model without aileron (fictitious control surface, FCS) is studied. The analytical results show that these two cases are substantial different. In aileron deflection case, the aeroelastic effect is disadvantageous, so the structural stiffness should be high until the electrical voltage is not necessary. But in the case of FCS,the aeroelastic effect is advantageous and it means that lower structural stiffness can lead to lower voltage. Compared with aileron project, the FCS project can save structure weight.展开更多
To overcome some of the problems inherent in conventional heating aids such as low gain at high fi'equencies due to acoustic feedback, discomfort in occlusion of the extemal ear canal and so on, implantable middle ea...To overcome some of the problems inherent in conventional heating aids such as low gain at high fi'equencies due to acoustic feedback, discomfort in occlusion of the extemal ear canal and so on, implantable middle ear hearing devices (IMEHDs) have been developed over the past two decades. For such kinds of IMEHDs, this paper presents the design of a floating mass piezoelectric actuator using a PMN-30%PT stack as a new type of vibrator. The proposed piezoelectric actuator consists of only three components of a piezoelectric stack, a metal case and a clamp. For the purpose of aiding the design of this actuator, a coupling biomechanics model of human middle ear and the piezoelectric actuator was constructed. This model was built based on a complete set of computerized tomography section images of a healthy volunteer's left ear by reverse engineering technology. The validity of this model was confirmed by comparing the motion of the tympanic membrane and stapes footplate obtained by this model with published experimental measurements on human temporal bones. It is shown that the designed actuator can be implanted on the incus long process by a simple surgical operation, and the stapes footplate displacement by its excitation at 10.5 V root-mean-square(RMS) voltage was equivalent to that from acoustic stimulation at 100 dB sound pressure level(SPL), which is adequate stimulation to the ossicular chain. The corresponding power consumption is 0.04 mW per volt of excitation at 1 kHz, which is low enough for the transducer to be used in an implantable middle ear device.展开更多
Due to the limited output capability of piezoelectric diaphragm pumps, the driving voltage is frequently increased to obtain the desired output. However, the excessive voltage application may lead to a large deformati...Due to the limited output capability of piezoelectric diaphragm pumps, the driving voltage is frequently increased to obtain the desired output. However, the excessive voltage application may lead to a large deformation in the piezoelectric ceramics, which could cause it to breakdown or become damaged. Therefore, increasing the number of chambers to obtain the desired output is proposed. Using a check-valve quintuple-chamber pump with quintuple piezoelectric actuators, the characteristics of the pump under different driving modes are investigated through experiments. By changing the number and connection mode of working actuators, pump performances in terms of flow rate and backpressure are tested at a voltage of 150 V with a frequency range of 60 Hz -400 Hz. Experiment results indicate that the properties of the multiple-chamber pump change significantly with distinct working chambers even though the number of pumping chambers is the same. Pump performance declines as the distance between the working actuators increases. Moreover, pump performance declines dramatically when the working piezoelectric actuator closest to the outlet is involved. The maximum backpressures of the pump with triple, quadruple, and quintuple actuators are increased by 39%, 83%, and 128%, respectively, compared with the pump with double working actuators; the corresponding maximum flow rates of the pumps are simply increased by 25.9%, 49.2%, and 67.8%, respectively. The proposed research offers practical guidance for the effective utilization of the multiple-chamber pumps under different driving modes.展开更多
This paper presents a new asymmetric hysteresis model and its application in the tracking control of piezoelectric actuators. The proposed model is based on a coupled-play operator which can avoid the conventional Pra...This paper presents a new asymmetric hysteresis model and its application in the tracking control of piezoelectric actuators. The proposed model is based on a coupled-play operator which can avoid the conventional Prandtl-Ishlinskii(CPI)model's defects, i.e., the symmetric property. The high accuracy for modeling asymmetric hysteresis is validated by comparing simulation results with experimental measurements. In order to further evaluate the performance of the proposed model in closed-loop tracking application, two different hybrid control methods which experimentally demonstrate their performance under the same operating conditions, are compared to validate that the hybrid control strategy with proposed hysteresis model can mitigate the hysteresis more effectively and achieve better tracking precision. The experimental results demonstrate that the proposed modeling and tracking control strategy can realize efficient control of piezoelectric actuator.展开更多
This research presents a finite element formulation based on four-variable refined plate theory for bending analysis of cross-ply and angle-ply laminated composite plates integrated with a piezoelectric fiber-reinforc...This research presents a finite element formulation based on four-variable refined plate theory for bending analysis of cross-ply and angle-ply laminated composite plates integrated with a piezoelectric fiber-reinforced composite actuator under electromechanical loading. The four-variable refined plate theory is a simple and efficient higher-order shear deformation theory, which predicts parabolic variation of transverse shear stresses across the plate thickness and satisfies zero traction conditions on the plate free surfaces. The weak form of governing equations is derived using the principle of minimum potential energy, and a 4-node non-conforming rectangular plate element with 8 degrees of freedom per node is introduced for discretizing the domain. Several benchmark problems are solved by the developed MATLAB code and the obtained results are compared with those from exact and other numerical solutions, showing good agreement.展开更多
The Flutter suppression using distributed piezoelectric actuators has been analyzed and tested. In constructing the finite element equation, effects of piezoelectric matrices are investigated. LQG method is used in de...The Flutter suppression using distributed piezoelectric actuators has been analyzed and tested. In constructing the finite element equation, effects of piezoelectric matrices are investigated. LQG method is used in designing the control law. In reducing the order of the control law, both balance realization and LK methods are used. For the rational approximation of the unsteady aerodynamic forces LS method is improved. In determining the piezoelectric constants d31 a new dynamic response method is developed. Laser vibrameter is used to pick up the model response and in ground resonance test the model is excited by piezoelectric actuators. Reasonable agreement of the wind tunnel flutter suppression test with calculated results is obtained.展开更多
We proposed a dynamic model identification and design of an H-Infinity (i.e.H) controller using a LightweightPiezo-Composite Actuator (LIPCA).A second-order dynamic model was obtained by using input and output dat...We proposed a dynamic model identification and design of an H-Infinity (i.e.H) controller using a LightweightPiezo-Composite Actuator (LIPCA).A second-order dynamic model was obtained by using input and output data, and applyingan identification algorithm.The identified model coincides well with the real LIPCA.To reduce the resonating mode that istypical of piezoelectric actuators, a notch filter was used.A feedback controller using the Hcontrol scheme was designed basedon the identified dynamic model; thus, the LIPCA can be easily used as an actuator for biomemetic applications such as artificialmuscles or macro/micro positioning in bioengineering.The control algorithm was implemented using a microprocessor, analogfilters, and power amplifying drivers.Our simulation and experimental results demonstrate that the proposed control algorithmworks well in real environment, providing robust performance and stability with uncertain disturbances.展开更多
Lead zirconate titanium solid-solution (PZT) thin films with variousthickness are synthesized on titanium substrates by repeated hydrothermal treatments. Young modulus,electric-field-induced displacement and the densi...Lead zirconate titanium solid-solution (PZT) thin films with variousthickness are synthesized on titanium substrates by repeated hydrothermal treatments. Young modulus,electric-field-induced displacement and the density of the PZT film are measured respectively.Bimorph- type bending actuators are fabricated using these films. The model, which is used toanalyze the driving ability of bimorph-type bending actuators by hydrothermal method, is set up. Itcan be seen that the driving ability of bimorph-type bending actuators can be greatly improved byoptimizing the thickness of PZT thin film and substrate from the theoretical analysis results. Themeasured values are expected to agree with the theoretical values calculated by the above model.展开更多
This paper presents the application of iterative learning control (ILC) to compensate hysteresis in a piezoelectric actuator. The proposed controller is a hybrid of proportional-integral-differential (PID) control, wh...This paper presents the application of iterative learning control (ILC) to compensate hysteresis in a piezoelectric actuator. The proposed controller is a hybrid of proportional-integral-differential (PID) control, whose main function is for trajectory tracking, and a chatter-based ILC, whose main function is for hysteresis compensation. Stability analysis of the proposed ILC is presented, with the PID included in the dynamic of the piezoelectric actuator. The performance of the proposed controller is analysed through simulation and verified with experiment with a piezoelectric actuator.展开更多
A non-resonant piezoelectric linear motor with a flexible driving end,which has an extensive working frequency range and good operation stability,is studied theoretically and experimentally.Based on the microscopic vi...A non-resonant piezoelectric linear motor with a flexible driving end,which has an extensive working frequency range and good operation stability,is studied theoretically and experimentally.Based on the microscopic vibration characteristics of the motor stator,the longitudinal vibration model is established for the whole motor system.According to the Coulomb friction model and the motor vibration model,the friction mechanism of the nonresonant piezoelectric linear motor is investigated by dynamical analysis of the whole motor system.Furthermore,the vibration characteristics and mechanical output characteristics of the stator are simulated and experimentally studied on the basis of the friction drive mechanism model.Finally,both the simulation and experimental results show that this kind of motor remain stable in the frequency domain from 2.2 kHz to 3.5 kHz and that when the pre-stress is 4 Nand the driving voltage is 90 V,the maximum velocity of the motor is above 4 mm/s and the maximum thrust is nearly 0.5 N.展开更多
Piezoelectric actuators (PEAs) have been widely used in micro- and nanopositioning applications due to their fine resolution, fast responses, and large actuating forces. However, the existence of nonlinearities such a...Piezoelectric actuators (PEAs) have been widely used in micro- and nanopositioning applications due to their fine resolution, fast responses, and large actuating forces. However, the existence of nonlinearities such as hysteresis makes modeling and control of PEAs challenging. This paper reviews the recent achievements in modeling and control of piezoelectric actuators. Specifically, various methods for modeling linear and nonlinear behaviors of PEAs, including vibration dynamics, hysteresis, and creep, are examined;and the issues involved are identified. In the control of PEAs as applied to positioning, a review of various control schemes of both model-based and non-model-based is presented along with their limitations. The challenges associated with the control problem are also discussed. This paper is concluded with the emerging issues identified in modeling and control of PEAs for future research.展开更多
CuO added Pb0.92Sr0.06Ba0.02(Mg1/3Nb2/3)0.25(Ti0.53Zr0.47)0.75O3 ceramics were studied to prepare high-quality multilayer piezoelectric actuators with pure Ag electrodes at 900 ℃. CuO addition not only reduced th...CuO added Pb0.92Sr0.06Ba0.02(Mg1/3Nb2/3)0.25(Ti0.53Zr0.47)0.75O3 ceramics were studied to prepare high-quality multilayer piezoelectric actuators with pure Ag electrodes at 900 ℃. CuO addition not only reduced the sintering temperature significantly from 1260 ℃ to 900 ℃ but also improved the ceramic density to 7.742 g/cm3. The 0.7 wt.% CuO added ceramic sintered at 900 ℃ shows the remnant polarization (Pr) of 40 μC/cm2, 0.28% strain at 40 kV/cm, and the piezoelectric coefficient (d33) of 630 pC/N. This ceramic shows a strong relaxor characteristic with a Curie temperature of 200 ℃. Furthermore, the 0.7 wt.% CuO added ceramic and pure Ag electrodes were co-fired at 900 ℃ to prepare a high-quality multilayer piezoelectric actuator with a d33 of over 450 pC/N per ceramic layer.展开更多
A new precision piezoelectric actuator is proposed to improve its drive capabilities. The actuator is based on the piezoelectric technology. It adopts the principle of bionics and works with a new method of stator ini...A new precision piezoelectric actuator is proposed to improve its drive capabilities. The actuator is based on the piezoelectric technology. It adopts the principle of bionics and works with a new method of stator initiative anchoring/loosen and a distortion structure of double-side thin flexible hinge. It solves the problem of anchoring/loosen, frequency, journey, resolution and velocity. The experiment shows that the new linear piezoelectric actuator works with high frequency (100 Hz), high speed (502 μm/s), large travel (〉10 mm), high resolution (0.05 μm) and high load (100 N). This kind of new piezoelectric actuator will be applied for large travel and high resolution driving device, optics engineering precision positioning and some micromanipulation field.展开更多
Piezoelectric bar-shaped resonators were proposed to act as hardness sensors in the 1960 s and stiffness sensors in the 1990 s based on the contact impedance method.In this work, we point out that both multilayer and ...Piezoelectric bar-shaped resonators were proposed to act as hardness sensors in the 1960 s and stiffness sensors in the 1990 s based on the contact impedance method.In this work, we point out that both multilayer and unimorph(or bimorph) piezoelectric actuators could act as stiffness/modulus sensors based on the principle of mechanical contact resonance. First, the practical design and the performance of a piezoelectric unimorph actuator–based stiffness sensor were presented. Then the working principle of piezoelectric multilayer actuator–based stiffness sensors was given and verified by numerical investigation. It was found that for these two types of resonance-based sensors, the shift of the resonance frequency due to contact is always positive, which is different from that of the contact impedance method. Further comparative sensitivity study indicated that the unimorph actuator–based stiffness sensor is very suitable for measurement on soft materials, whereas the multilayer actuator–based sensor is more suitable for hard materials.展开更多
A novel robust controller is proposed in this study to realize the precise motion control of a cell puncture mechanism(CPM)driven by piezoelectric ceramics(PEAs).The entire dynamic model of CPM is constructed based on...A novel robust controller is proposed in this study to realize the precise motion control of a cell puncture mechanism(CPM)driven by piezoelectric ceramics(PEAs).The entire dynamic model of CPM is constructed based on the Bouc–Wen model,and the nonlinear part of the dynamic model is optimized locally to facilitate the construction of a robust controller.A model-based,nonlinear robust controller is constructed using time-delay estimation(TDE)and fractional-order nonsingular terminal sliding mode(FONTSM).The proposed controller does not require prior knowledge of unknown disturbances due to its real-time online estimation and compensation of unknown terms by using the TDE technology.The controller also has finite-time convergence and high-precision trajectory tracking capabilities due to FONTSM manifold and fast terminal sliding mode-type reaching law.The stability of the closed-loop system is proved by Lyapunov stability theory.Computer simulation and hardware-in-loop simulation experiments of CPM verify that the proposed controller outperforms traditional terminal sliding mode controllers,such as the integer-order or model-free controller.The proposed controller can also continuously output without chattering and has high control accuracy.Zebrafish embryo is used as a verification target to complete the cell puncture experiment.From the engineering application perspective,the proposed control strategy can be effectively applied in a PEA-driven CPM.展开更多
Micro Aerial Vehicles(MAVs) are the smallest artificial aircraft.Most of the flapping wings MAVs are powered by electric motors of various capacities.We report in this paper the application of piezoelectric actuators ...Micro Aerial Vehicles(MAVs) are the smallest artificial aircraft.Most of the flapping wings MAVs are powered by electric motors of various capacities.We report in this paper the application of piezoelectric actuators as power system for a flapping wing MAV using a compliant displacement amplification mechanism.The actuator used for this application is a pre-stressed cut piece of TH-7R type Thunder actuator.A two-bar compliant mechanism with two flexures has been developed to convert the linear displacement into angular movement and amplification.The specimens were made from carbon fiber links and nylon flexures.We also proposed to use the product of frequency(F) and tip displacement(D), F * D as a criteria for the characterization of an amplifying mechanism.The best specimen according to this criterion is obtained for a 5mm length flexure specimen made of three layers of nylon.The F*D value obtained for this specimen was(0.58) Hz.m.ANSYS finite element analysis results for different flexural thickness and lengths were obtained and have been compared to the experimental results.The effect of both the thickness and length of the flexure on a particular arrangement has been discussed.展开更多
Positioning with high precision piezoelectric actuators is widely used.To overcome positioning inaccuracy caused by hysteresis and creep of actuators,a precise tracking method for piezoelectric actuators using active ...Positioning with high precision piezoelectric actuators is widely used.To overcome positioning inaccuracy caused by hysteresis and creep of actuators,a precise tracking method for piezoelectric actuators using active disturbance rejection control(ADRC) has been proposed in this paper.This method,in real-time,actively estimates and compensates parameter uncertainties,nonlinear factors such as hysteresis,and external disturbances in the tracking system.Precise tracking of the piezoelectric actuator can be achieved without any form of feedforward compensations.The experimental results demonstrate that the active disturbance rejection controller can reduce tracking errors by over90%comparing with those using the PID controller.Those features of the proposed control method are very suitable for applications in adaptive optics.展开更多
文摘Circular holes are commonly employed in engineering designs;however, they often serve as locations where cracks initiate and propagate. This paper explores a novel approach to structural repair by utilizing piezoelectric actuators. The primary focus of this study is to investigate the influence of an adhesively bonded piezoelectric actuator patch placed above a circular hole on the stress intensity factor (SIF) in an aluminium plate. The plate is subjected to uniaxial tensile stress, while the piezoelectric actuator is excited with varying voltage levels. The analysis is conducted using the finite element method (FEM), a powerful numerical technique for simulating complex structures. The study assesses the stress distribution and employs the SIF as an adequate criterion for evaluating the impact of different patch configurations. The results indicate a strong correlation between the applied voltage and the SIF. Whether the SIF increases or decreases depends on the polarization of the piezoelectric actuator. Particularly noteworthy is the finding that rectangular patches in a horizontal orientation significantly reduce the SIF compared to other patch geometries. Moreover, double-sided patches exhibit a pronounced decrease in the SIF compared to single-sided patches. In summary, this research underscores the potential of piezoelectric actuators in mitigating stress intensity in structures with circular hole with crack initiation. It offers valuable insights into the influence of applied voltage, patch geometry, and patch placement on the SIF, thereby contributing to developing effective strategies for enhancing structural integrity.
基金supported by the Japan Society for the Promotion of Science under KAKENHI Grant Nos.19F19379 and 20H04199。
文摘This paper demonstrates the importance of three-dimensional(3-D)piezoelectric coupling in the electromechanical behavior of piezoelectric devices using three-dimensional finite element analyses based on weak and strong coupling models for a thin cantilevered piezoelectric bimorph actuator.It is found that there is a significant difference between the strong and weak coupling solutions given by coupling direct and inverse piezoelectric effects(i.e.,piezoelectric coupling effect).In addition,there is significant longitudinal bending caused by the constraint of the inverse piezoelectric effect in the width direction at the fixed end(i.e.,3-D effect).Hence,modeling of these effects or 3-D piezoelectric coupling modeling is an electromechanical basis for the piezoelectric devices,which contributes to the accurate prediction of their behavior.
文摘Piezoelectric actuators are distributed on both side of a rectangular wing model,and the possibility of improvement of aircraft rolling power is investigated. The difference between the model with aileron deflection and the model without aileron (fictitious control surface, FCS) is studied. The analytical results show that these two cases are substantial different. In aileron deflection case, the aeroelastic effect is disadvantageous, so the structural stiffness should be high until the electrical voltage is not necessary. But in the case of FCS,the aeroelastic effect is advantageous and it means that lower structural stiffness can lead to lower voltage. Compared with aileron project, the FCS project can save structure weight.
基金supported by National Natural Science Foundation of China (Grant No. 10772121)
文摘To overcome some of the problems inherent in conventional heating aids such as low gain at high fi'equencies due to acoustic feedback, discomfort in occlusion of the extemal ear canal and so on, implantable middle ear hearing devices (IMEHDs) have been developed over the past two decades. For such kinds of IMEHDs, this paper presents the design of a floating mass piezoelectric actuator using a PMN-30%PT stack as a new type of vibrator. The proposed piezoelectric actuator consists of only three components of a piezoelectric stack, a metal case and a clamp. For the purpose of aiding the design of this actuator, a coupling biomechanics model of human middle ear and the piezoelectric actuator was constructed. This model was built based on a complete set of computerized tomography section images of a healthy volunteer's left ear by reverse engineering technology. The validity of this model was confirmed by comparing the motion of the tympanic membrane and stapes footplate obtained by this model with published experimental measurements on human temporal bones. It is shown that the designed actuator can be implanted on the incus long process by a simple surgical operation, and the stapes footplate displacement by its excitation at 10.5 V root-mean-square(RMS) voltage was equivalent to that from acoustic stimulation at 100 dB sound pressure level(SPL), which is adequate stimulation to the ossicular chain. The corresponding power consumption is 0.04 mW per volt of excitation at 1 kHz, which is low enough for the transducer to be used in an implantable middle ear device.
基金Supported by National Natural Science Foundation of China(Grant Nos.51205366,51205367,51377147)Zhejiang Provincial Natural Science Foundation of China(Grant No.LQ13E050007)
文摘Due to the limited output capability of piezoelectric diaphragm pumps, the driving voltage is frequently increased to obtain the desired output. However, the excessive voltage application may lead to a large deformation in the piezoelectric ceramics, which could cause it to breakdown or become damaged. Therefore, increasing the number of chambers to obtain the desired output is proposed. Using a check-valve quintuple-chamber pump with quintuple piezoelectric actuators, the characteristics of the pump under different driving modes are investigated through experiments. By changing the number and connection mode of working actuators, pump performances in terms of flow rate and backpressure are tested at a voltage of 150 V with a frequency range of 60 Hz -400 Hz. Experiment results indicate that the properties of the multiple-chamber pump change significantly with distinct working chambers even though the number of pumping chambers is the same. Pump performance declines as the distance between the working actuators increases. Moreover, pump performance declines dramatically when the working piezoelectric actuator closest to the outlet is involved. The maximum backpressures of the pump with triple, quadruple, and quintuple actuators are increased by 39%, 83%, and 128%, respectively, compared with the pump with double working actuators; the corresponding maximum flow rates of the pumps are simply increased by 25.9%, 49.2%, and 67.8%, respectively. The proposed research offers practical guidance for the effective utilization of the multiple-chamber pumps under different driving modes.
基金supported by the National Natural Science Foundation of China(51505133,61108038)the Doctoral Science Foundation of Henan Polytechnic University(60407/010)Chunhui Program of Ministry of Education of China(Z2011069)
文摘This paper presents a new asymmetric hysteresis model and its application in the tracking control of piezoelectric actuators. The proposed model is based on a coupled-play operator which can avoid the conventional Prandtl-Ishlinskii(CPI)model's defects, i.e., the symmetric property. The high accuracy for modeling asymmetric hysteresis is validated by comparing simulation results with experimental measurements. In order to further evaluate the performance of the proposed model in closed-loop tracking application, two different hybrid control methods which experimentally demonstrate their performance under the same operating conditions, are compared to validate that the hybrid control strategy with proposed hysteresis model can mitigate the hysteresis more effectively and achieve better tracking precision. The experimental results demonstrate that the proposed modeling and tracking control strategy can realize efficient control of piezoelectric actuator.
文摘This research presents a finite element formulation based on four-variable refined plate theory for bending analysis of cross-ply and angle-ply laminated composite plates integrated with a piezoelectric fiber-reinforced composite actuator under electromechanical loading. The four-variable refined plate theory is a simple and efficient higher-order shear deformation theory, which predicts parabolic variation of transverse shear stresses across the plate thickness and satisfies zero traction conditions on the plate free surfaces. The weak form of governing equations is derived using the principle of minimum potential energy, and a 4-node non-conforming rectangular plate element with 8 degrees of freedom per node is introduced for discretizing the domain. Several benchmark problems are solved by the developed MATLAB code and the obtained results are compared with those from exact and other numerical solutions, showing good agreement.
文摘The Flutter suppression using distributed piezoelectric actuators has been analyzed and tested. In constructing the finite element equation, effects of piezoelectric matrices are investigated. LQG method is used in designing the control law. In reducing the order of the control law, both balance realization and LK methods are used. For the rational approximation of the unsteady aerodynamic forces LS method is improved. In determining the piezoelectric constants d31 a new dynamic response method is developed. Laser vibrameter is used to pick up the model response and in ground resonance test the model is excited by piezoelectric actuators. Reasonable agreement of the wind tunnel flutter suppression test with calculated results is obtained.
基金supported by the Korea Research Foundation Grant(KRF-2006-005-J03303)
文摘We proposed a dynamic model identification and design of an H-Infinity (i.e.H) controller using a LightweightPiezo-Composite Actuator (LIPCA).A second-order dynamic model was obtained by using input and output data, and applyingan identification algorithm.The identified model coincides well with the real LIPCA.To reduce the resonating mode that istypical of piezoelectric actuators, a notch filter was used.A feedback controller using the Hcontrol scheme was designed basedon the identified dynamic model; thus, the LIPCA can be easily used as an actuator for biomemetic applications such as artificialmuscles or macro/micro positioning in bioengineering.The control algorithm was implemented using a microprocessor, analogfilters, and power amplifying drivers.Our simulation and experimental results demonstrate that the proposed control algorithmworks well in real environment, providing robust performance and stability with uncertain disturbances.
基金This project is supported by National Natural Science Foundation of China(No.90207003) and Returnee Foundation of Dalian.
文摘Lead zirconate titanium solid-solution (PZT) thin films with variousthickness are synthesized on titanium substrates by repeated hydrothermal treatments. Young modulus,electric-field-induced displacement and the density of the PZT film are measured respectively.Bimorph- type bending actuators are fabricated using these films. The model, which is used toanalyze the driving ability of bimorph-type bending actuators by hydrothermal method, is set up. Itcan be seen that the driving ability of bimorph-type bending actuators can be greatly improved byoptimizing the thickness of PZT thin film and substrate from the theoretical analysis results. Themeasured values are expected to agree with the theoretical values calculated by the above model.
文摘This paper presents the application of iterative learning control (ILC) to compensate hysteresis in a piezoelectric actuator. The proposed controller is a hybrid of proportional-integral-differential (PID) control, whose main function is for trajectory tracking, and a chatter-based ILC, whose main function is for hysteresis compensation. Stability analysis of the proposed ILC is presented, with the PID included in the dynamic of the piezoelectric actuator. The performance of the proposed controller is analysed through simulation and verified with experiment with a piezoelectric actuator.
基金supported by the National Natural Science Foundations of China(Nos.51405420,51375224,61503319)the Natural Science Foundation of Jiangsu Province(No.BK20140474)+2 种基金the Sponsorship of Jiangsu Oversea Research and Training Program for University Prominent Young&Middle-aged Teachersthe Jiangsu Province Ordinary University Professional Degree Graduate Innovation Project(No.SJZZ16_0294)Qing Lan Project of Jiangsu Higher Education of China(No.Su-Teacher2018-12)
文摘A non-resonant piezoelectric linear motor with a flexible driving end,which has an extensive working frequency range and good operation stability,is studied theoretically and experimentally.Based on the microscopic vibration characteristics of the motor stator,the longitudinal vibration model is established for the whole motor system.According to the Coulomb friction model and the motor vibration model,the friction mechanism of the nonresonant piezoelectric linear motor is investigated by dynamical analysis of the whole motor system.Furthermore,the vibration characteristics and mechanical output characteristics of the stator are simulated and experimentally studied on the basis of the friction drive mechanism model.Finally,both the simulation and experimental results show that this kind of motor remain stable in the frequency domain from 2.2 kHz to 3.5 kHz and that when the pre-stress is 4 Nand the driving voltage is 90 V,the maximum velocity of the motor is above 4 mm/s and the maximum thrust is nearly 0.5 N.
文摘Piezoelectric actuators (PEAs) have been widely used in micro- and nanopositioning applications due to their fine resolution, fast responses, and large actuating forces. However, the existence of nonlinearities such as hysteresis makes modeling and control of PEAs challenging. This paper reviews the recent achievements in modeling and control of piezoelectric actuators. Specifically, various methods for modeling linear and nonlinear behaviors of PEAs, including vibration dynamics, hysteresis, and creep, are examined;and the issues involved are identified. In the control of PEAs as applied to positioning, a review of various control schemes of both model-based and non-model-based is presented along with their limitations. The challenges associated with the control problem are also discussed. This paper is concluded with the emerging issues identified in modeling and control of PEAs for future research.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.51472118,51602156,52177072,and 11274174)the Fundamental Research Funds for the Central Universities,China(Grant Nos.30916011104 and 30916011208)
文摘CuO added Pb0.92Sr0.06Ba0.02(Mg1/3Nb2/3)0.25(Ti0.53Zr0.47)0.75O3 ceramics were studied to prepare high-quality multilayer piezoelectric actuators with pure Ag electrodes at 900 ℃. CuO addition not only reduced the sintering temperature significantly from 1260 ℃ to 900 ℃ but also improved the ceramic density to 7.742 g/cm3. The 0.7 wt.% CuO added ceramic sintered at 900 ℃ shows the remnant polarization (Pr) of 40 μC/cm2, 0.28% strain at 40 kV/cm, and the piezoelectric coefficient (d33) of 630 pC/N. This ceramic shows a strong relaxor characteristic with a Curie temperature of 200 ℃. Furthermore, the 0.7 wt.% CuO added ceramic and pure Ag electrodes were co-fired at 900 ℃ to prepare a high-quality multilayer piezoelectric actuator with a d33 of over 450 pC/N per ceramic layer.
基金This project is supported by National Hi-tech Research and Development Program of China(863 Program, No.2002AA423150)
文摘A new precision piezoelectric actuator is proposed to improve its drive capabilities. The actuator is based on the piezoelectric technology. It adopts the principle of bionics and works with a new method of stator initiative anchoring/loosen and a distortion structure of double-side thin flexible hinge. It solves the problem of anchoring/loosen, frequency, journey, resolution and velocity. The experiment shows that the new linear piezoelectric actuator works with high frequency (100 Hz), high speed (502 μm/s), large travel (〉10 mm), high resolution (0.05 μm) and high load (100 N). This kind of new piezoelectric actuator will be applied for large travel and high resolution driving device, optics engineering precision positioning and some micromanipulation field.
基金financial support of the National Natural Science Foundation of China (Grant11090331)Support from the Chinese National Programs for Scientific Instruments Research and Development (Grant 2012YQ03007502)
文摘Piezoelectric bar-shaped resonators were proposed to act as hardness sensors in the 1960 s and stiffness sensors in the 1990 s based on the contact impedance method.In this work, we point out that both multilayer and unimorph(or bimorph) piezoelectric actuators could act as stiffness/modulus sensors based on the principle of mechanical contact resonance. First, the practical design and the performance of a piezoelectric unimorph actuator–based stiffness sensor were presented. Then the working principle of piezoelectric multilayer actuator–based stiffness sensors was given and verified by numerical investigation. It was found that for these two types of resonance-based sensors, the shift of the resonance frequency due to contact is always positive, which is different from that of the contact impedance method. Further comparative sensitivity study indicated that the unimorph actuator–based stiffness sensor is very suitable for measurement on soft materials, whereas the multilayer actuator–based sensor is more suitable for hard materials.
文摘A novel robust controller is proposed in this study to realize the precise motion control of a cell puncture mechanism(CPM)driven by piezoelectric ceramics(PEAs).The entire dynamic model of CPM is constructed based on the Bouc–Wen model,and the nonlinear part of the dynamic model is optimized locally to facilitate the construction of a robust controller.A model-based,nonlinear robust controller is constructed using time-delay estimation(TDE)and fractional-order nonsingular terminal sliding mode(FONTSM).The proposed controller does not require prior knowledge of unknown disturbances due to its real-time online estimation and compensation of unknown terms by using the TDE technology.The controller also has finite-time convergence and high-precision trajectory tracking capabilities due to FONTSM manifold and fast terminal sliding mode-type reaching law.The stability of the closed-loop system is proved by Lyapunov stability theory.Computer simulation and hardware-in-loop simulation experiments of CPM verify that the proposed controller outperforms traditional terminal sliding mode controllers,such as the integer-order or model-free controller.The proposed controller can also continuously output without chattering and has high control accuracy.Zebrafish embryo is used as a verification target to complete the cell puncture experiment.From the engineering application perspective,the proposed control strategy can be effectively applied in a PEA-driven CPM.
文摘Micro Aerial Vehicles(MAVs) are the smallest artificial aircraft.Most of the flapping wings MAVs are powered by electric motors of various capacities.We report in this paper the application of piezoelectric actuators as power system for a flapping wing MAV using a compliant displacement amplification mechanism.The actuator used for this application is a pre-stressed cut piece of TH-7R type Thunder actuator.A two-bar compliant mechanism with two flexures has been developed to convert the linear displacement into angular movement and amplification.The specimens were made from carbon fiber links and nylon flexures.We also proposed to use the product of frequency(F) and tip displacement(D), F * D as a criteria for the characterization of an amplifying mechanism.The best specimen according to this criterion is obtained for a 5mm length flexure specimen made of three layers of nylon.The F*D value obtained for this specimen was(0.58) Hz.m.ANSYS finite element analysis results for different flexural thickness and lengths were obtained and have been compared to the experimental results.The effect of both the thickness and length of the flexure on a particular arrangement has been discussed.
基金Supported by the National Natural Science Foundation of China(No.11373048)
文摘Positioning with high precision piezoelectric actuators is widely used.To overcome positioning inaccuracy caused by hysteresis and creep of actuators,a precise tracking method for piezoelectric actuators using active disturbance rejection control(ADRC) has been proposed in this paper.This method,in real-time,actively estimates and compensates parameter uncertainties,nonlinear factors such as hysteresis,and external disturbances in the tracking system.Precise tracking of the piezoelectric actuator can be achieved without any form of feedforward compensations.The experimental results demonstrate that the active disturbance rejection controller can reduce tracking errors by over90%comparing with those using the PID controller.Those features of the proposed control method are very suitable for applications in adaptive optics.