Experimental Study of Cavitation Phenomenon in a Centrifugal Blood Pump Induced by the Failure of Inlet Cannula

Cavitation of centrifugal blood pump is a serious problem accompany with the blocking failure of short inlet cannula. However, hardly any work has been seen in published literature on this complex cavitation phenomenon caused by the coupling effect of inlet cannula blocking and pumps suction. Even for cavitation studies on ordinary centrifugal pumps, similar researches on this issue are rare. In this paper, the roles of throttling, rotation speed and fluid viscosity on bubble inception and intensity in a centrifugal blood pump are studied, on the basis of experimental observations. An adjustable throttle valve installed just upstream blood pump inlet is used to simulate the throttling effect of the narrowed inlet cannula. The rotation speed is adjusted from 2 600 r/rain to 3 200 r/min. Glycerin water solutions are used to investigate the influences of kinetic viscosity. Bubbles are recorded with a high-speed video camera. Direct observation shows that different from cavitation in industrial centrifugal pumps, gas nuclei appears at the nearby of vane leading edges while throttling is light, then moves upstream to the joint position of inlet pipe and pump with the closing of the valve. It＇s found that the critical inlet pressure, obtained when bubbles are first observed, decreases linearly with viscosity and the slope is independent with rotation speeds; the critical inlet pressure and the inlet extreme pressure which is obtained when the throttle valve is nearly closed, fall linearly with rotation speed respectively and the relative pressure between them is independent with rotation speed and fluid viscosity. This paper studies experimentally on cavitation in centrifugal blood pump that caused by the failure of assembled short inlet cannula, which mav beneficial the desima of centrifugal blood Dumo with inlet cannula.

Computational Fluid Dynamics Analysis of Shroud Design on Hemodynamic Performance and Blood Damage in a Centrifugal Blood Pump

Patients with extracorporeal membrane oxygenation still suffer from high rates of complication that linked to the flow field within the blood pump.So it is essential to optimise the geometry of the pump.The specification of shroud design is arguably the necessary design parameter in the centrifugal pump.However,the hemodynamic performances of the different shroud designs have not been studied extensively.In this study,ten different shroud designs were made and divided into two groups as the different covering locations(A:Covering the blade leading edge,B:Covering the blade trailing edge).In every group,six shroud designs with the covering proportions of 0,1/5,2/5,3/5,4/5,1 were made.Detailed computational fluid dynamics(CFD)analyses were performed to investigate their effects on hemodynamics and hydraulic performance at the constant flow condition(4000 rpm,5 L/min).The percentage volumes of the scalar shear stress in specific threshold(τ<1 Pa:Thrombosis,τ>9 Pa:the destruction of von Willebrand factor,τ>50 Pa:Platelet activation,τ>150 Pa:Break of red blood)were used to compare the blood damage of the different shroud designs.Also,the modified index of hemolysis(MIH)were calculated based on a Eulerian approach for different pumps.CFD simulations predicted an increase in the pump head,hydraulic efficiency,a fraction of fluid volume with scalar shear stress values above a threshold(9 Pa,50 Pa,150 Pa)and MIH with increasing shroud covering proportions from 0 to 1 in the same covering location.Also,these above results were higher in group B than group A.This means that the risks of the hemolysis,thrombosis and bleeding increased as the rise of the covering proportion and they were higher in the pump whose shroud covers the blade trailing edge.

Numerical Simulation and Experimental Research on Passive Hydrodynamic Bearing in a Blood Pump

The current research of hydrodynamic bearing in blood pump mainly focuses on the bearing structure design.Compared with the typical plane slider bearing and Rayleigh step bearing,spiral groove bearing has excellent performance in load-carrying capacity.However,the load-carrying capacity would decrease significantly with increasing flow rate in conventional designs.In this paper,the special treatment is made to the upper spiral groove bearing to make sure that both the circulatory flowing and load-carrying capacity are high.Three-dimensional computational fluid dynamics(CFD) models in the space between rotor and shaft are developed by using FLUENT software.Effects of groove number,film height and groove depth on load-carrying capacity of the spiral groove bearings are investigated by orthogonal experiment design.The experimental results show that film height is the most remarkable factor to the load-carrying capacity.The variation tendency of load-carrying capacity reveals that the best combination of geometry is the one with groove number of 8,film height 0.03 mm and groove depth 0.08 mm.The velocity and pressure distributions in spiral groove bearings are also analyzed,and the analysis result shows that the distributions are in conformity with the design of the blood pump based on the principle of hydrodynamic bearing.The displacement of the rotor with the best combination parameters is tested by using laser displacement sensors,the testing result shows that the suspending performance is satisfactory both in axial and radial directions.This research proposes a bearing design method which has sufficient load-carrying capacity to support rotor as an effective passive hydrodynamic bearing.

Numerical Analyses of Idealized Total Cavopulmonary Connection Physiologies with Single and Bilateral Superior Vena Cava Assisted by an Axial Blood Pump

Our study evaluated the hemodynamic performance of an axial flow blood pump surgically implanted in idealized total cavopulmonary connection(TCPC)models.This blood pump was designed to augment pressure from the inferior vena cava(IVC)to the pulmonary circulation.Two Fontan procedures with single and bilateral superior vena cava(SVC)were compared to fit the mechanical supported TCPC physiologies.Computational fluid dynamics(CFD)analyses of two Pump-TCPC models were performed in the analyses.Pressure-flow characteristics,energy efficiency,fluid streamlines,hemolysis and thrombosis analyses were implemented.Numerical simulations indicate that the pump produces pressure generations of 1 mm to 24 mm Hg for rotational speeds ranging from 2000 RPM to 5000 RPM and flow rates of 2 LPM to 4 LPM.Two surgical models incorporated with the pump were found to be insignificant in pressure augmentation and energy boost.The risk assessment of blood trauma and thrombosis generation was evaluated representatively through blood damage index(BDI),particle resident time(PRT)and relative resistant time(RRT).The hemolysis and thrombosis analyses declare the advantage of the pump supported bilateral SVC surgical scheme in balancing flow distribution and reducing the risk of endothelial cell destruction and trauma generation.

Improved Hemolytic Performance of Blood Pump with Fluorine-Doped Hydrogenated Amorphous Carbon Coating

Fluorine-doped hydrogenated amorphous carbon (a-C:H:F) film was deposited on a flow-straightener, impeller and diffuser surface (SUS 304) of an enclosed-impeller type flow blood pump using the ionization deposition method with a source gas of C6F5H. The surface characteristics of the a-C:H:F film were examined using atomic force microscopy, X-ray photoelectron spectroscopy, and measurements of surface roughness, friction and surface potential. The a-C:H:F film tends to increase surface roughness and the negative surface charge. In addition, the surface energy and friction decrease with fluorine dopant in the a-C:H film. To estimate the hemolytic performance of a blood pump with the a-C:H:F film coating, the amount of hemolysis was measured using a mock circulatory system (in vitro test) with 500 mL of pig blood containing sodium citrate. In vitro test was conducted for 180 min with the blood flow and pump head maintained at 5 L/min and 100 mmHg, respectively. The a-C:H:F film coating reduced the amount of hemolysis and improved the hemolytic performance. Decreasing the surface energy and negative surface charge of the a-C:H:F film contributes to the improvement of the hemolytic performance. The a-C:H:F film coating is thus expected to be utilized in medical technology as a surface coating technology for artificial heart blood pumps.

Left Ventricle Failure and Blood Flow Estimation for Centrifugal Blood Pumps

This paper shows the blood flow control （FwC） performance to adjust rotational speed of an ICBP （implantable centrifugal blood pump） in order to provide an adequate flow to left ventricle in different patient conditions. ICBP is a totally implantable LVAD （left ventricular assist device） with ceramic bearings developed for long term circulatory assistance. FwC uses PI （proportional-integral） control to adjust rotational speed in order to provide blood flow. FwC does not use sensor for feedback, as there is an estimation system to provide blood flow measurement. Control strategy has being studied in a HCS （hybrid cardiovascular simulator） as a tool that allows the physical connection of ICBP during evaluation. In addition, HCS allows changes of some cardiovascular parameters in order to simulate specific heart disease： ejection fraction （10-25%） and heart rate （50-110 bpm）. FwC was able to adjust blood flow with steady error less than 2%. Results demonstrated that FwC is adequate to LVAD control irL different left ventricle failure conditions.

Epidural Blood Patch for Treatment of Postdural Puncture Headache in a Patient with Spinal Fusion and Recent Implantation of Intrathecal Pain Pump

We present an interesting case report of a 49-year-old female who presented with symptoms of post-dural puncture headache following implantation of an intrathecal pain pump. Her history was complicated by previous multi-level spinal fusion with hardware. The patient was evaluated and felt to be a candidate for epidural blood patch, which she elected to proceed with. Under fluoroscopic guidance epidural blood patch was successfully performed. Immediately following the procedure the patient noted significant improvement in the headache and six hours following the procedure was headache free and remained so at follow up three weeks later.

Subdural Hematoma and Postdural Puncture Headache from Intrathecal Pump Placement Resolved with Lumbar Epidural Blood Patch

Intrathecal drug delivery systems are commonly used in the management of chronic pain, cancer pain and neuromuscular disorders with muscle spasticity. The complications associated with in-trathecal pump placement include persistent cerebrospinal fluid (CSF) leak, hygroma, meningitis, and granuloma formation. A severe persistent CSF leak may cause postdural puncture headache along with acute intracranial subdural hematoma, which can be potentially life threatening. Surgical exploration with dural repair is required to treat this severe complication when conservative treatments fail. We present a case report of severe persistent CSF leak after intrathecal pump revision that resulted in a subdural hematoma and postdural puncture headache. In this case, an epidural blood patch was performed using epidural catheter under fluoroscopic guidance to target the site of CSF leak and to avoid damaging the intrathecal catheter. This patient’s headache was resolved and intrathecal catheter remained intact after this blood patch.

Numerical Investigation of an Idealized Total Cavopulmonary Connection Physiology Assisted by the Axial Blood Pump With and Without Diffuser

In order to improve the surgical treatment of the congenital heart disease patient with single ventricle defect,two axial flow blood pumps,one with diffuser and the other without diffuser,were designed and virtually implanted into an idealized total cavopulmonary connection(TCPC)model to form two types of Pump-TCPC physiological structure.Computational fluid dynamics(CFD)simulationswere performed to analyze the variations of the hemodynamic characteristics,such as flow field,wall shear stress(WSS),oscillatory shear index(OSI),relative residence time(RRT),between the two Pump-TCPC models.Numerical results indicate that the Pump-TCPC with diffuser has better flow field stability,less damage on endothelial cell of vessel wall,and lower risk of vascular injury and thrombosis formation than that without diffuser.

Effect of ultraviolet blood irradiation and oxygenation on nerve function and function of the red blood cell membrane pump in patients with acute cerebral infarction

BACKGROUND： Ultraviolet blood irradiation and oxygenation （UBIO） has obtained better clinical effect in treating acute cerebral infarction, but the mechanism underlying this effect remains unclear. OBJECTIVE： To observe the effect of UBIO on the nerve function and activities of K^＋-Na^＋-ATPase and Ca2^＋-Mg2^＋-ATPase activities on the red blood cell （RBC） membrane of patients with acute cerebral infarction. DESIGN： A randomized and controlled study.SETTING： Department of Neurology, Xiangfan Central Hospital.PARTICIPANTS： From January 2000 to December 2001, excluding those above 70 years old, 58 cases of 700 patients with acute cerebral infarction admitted in the Department of Neurology, Xiangfan Central Hospital, were recruited and divided into two groups according to the random number table： UBIO treated group （n=28）, including 17 males and 11 females, aged 40-68 years; and control group （n=30）, including 20 males and 10 females, aged 44-69 years. All the patients agreed to participate in the therapeutic program and detected items. The general informations were comparable without obvious differences between the two groups （P 〉 0.05）.METHODS： ① The patients in both groups received routine treatments, besides, those in the UBIO treated group were given UBIO treatment by using the XL-200 type therapeutic apparatus produced in Shijiazhuang, whose ultraviolet wave was set at 253.7 nm with the energy density of 0.568 J/m^2 per second, UBIO treatment started from the second day after admission, once every other day, with a single course consisting of 5-7 treatments. ② In the UBIO treated group, the venous blood was sampled before and after the first, third and the completion of the treatment course respectively, the venous blood was taken at each corresponding time point in the control group. After centrifugation of the blood at 10 000 rounds per minute, the RBC membrane was separated and then the activities of K^＋-Na^＋-ATPase and Ca2^＋-Mg2^＋-ATPase were detected by means of phosphorus determination.③ The nerve function was scored before and after treatment in both groups with European stroke scale, which included 13 items, the total score was 0-100 points, the higher the score, the better the nerve function. MAIN OUTCOME MEASURES ：①Score of European stroke scale before and after treatment in both groups.② Comparison of the activities of K^＋-Na^＋-ATPase and Ca2^＋-Mg2^＋-ATPase on RBC membrane between the two groups before treatment and after the first, third and the completion of the treatment. RESULTS： All the 58 patients with cerebral infarction were involved in the analysis of results.① The score of European stroke scale had no obvious difference between the two groups [（49.31±11.48）, （50.58±12.63）, P 〉 0.05], and it was obviously higher in the UBIO treated group than in the control group after treatment [84.66±13.75）, （77.05±11.17）, P 〈 0.05].②The activity of K^＋-Na^＋-ATPase on RBC membrane in the UBIO treated group was significantly increased after the first and third treatment as compared with before treatment [（31.56±19.25）, （27.64±15.83）, （17.67±13.83）, P 〈 0.01], it was still higher after the completion of the treatment than before treatment without obvious difference [（20.86±14.53）, P 〉 0.05]. After the first and third treatment, it was obviously higher in the UBIO treated group than in the control group [19.31±11.88）, （17.44±10.42）, P 〈 0.01]. ③ In the UBIO treated group, Ca2^＋-Mg2^＋-ATPase activity on RBC membrane significantly increased after the first treatment and remained higher than the pre-treatment level throughout the treatment [（27.49±14.72）, （17.41±4.82）, P 〈 0.01]. The activity of Ca2^＋-Mg2^＋-ATPase on RBC membrane was markedly higher in the UBIO treated group than in the control group after after the first, third and the completion of treatment respectively [（24.83±12.88）, （17.70±5.69）; （28.08±13.44）, （16.32±5.29）; （17.42±6.04）, P〈 0.05-0.01]. CONCLUSION： The effect of UBIO treatment against acute cerebral infarction may be mediated by the increased K^＋-Na^＋ ATPase and Ca2^＋-Mg2^＋-ATPase activities on RBC membrane, which enhances the RBC transformation ability so as to lower RBC aggregation and correct high blood viscosity.

The Characteristics of a Spiral Blood Pump

From 1997 to 1999, we developed a spiral blood pump. The spiral pump consists of a brushless DC motor, the pump housing, a magnetic-fluid seal, bearings and a spiral impeller. The maximum diameter of the impeller is 21.8 mm and minimum is 9.8 mm, the cone angle of the impeller threads is 41.8 degrees. The housing has a maximum diameter of 30 mm. The pump was made from Titanium alloy, the total volume of pump housing and motor was 76 ml and its weight 220g. Methods used: The hydrodynamic performance of the spiral pump was examined from 8 000 to 10 000rpm rotation speeds in a closed circuit loop. This circuit consists of a reservoir, a clamp, two pressure transducers, an electric-magnetic flow rate transducer and glycerin-water solution. The damage test to blood was studied in a smaller circuit loop, that used fresh sheep blood and polyvinyl chloride bag instead of the glycerin-water solution and the reservoir. In this test, the damage of the spiral pump was compared with an axial flow blood pump. Furthermore the simulated condition was 5.0 L/ min flow rate and 100 mmHg pressure. Summarize Results: 1. The flow rate was 4.0 L/min against 120 mmHg pressure when pump rotated 10000 rpm. So the hydrodynamic performance of the spiral blood pump was enough to meet a patient’s need when the blood pump was used as a left ventricular assistant device. 2. The NIH results of three gaps were 0.074±0.022g/100L,0.086±.026g/100L and 0.111±0.034g/100L(n=40) respectively. The best hemolysis result was been at the gap of 0.14 mm. 3. The NIH result of the spiral pump with 0.40gap was 0.111±0.034g/100L, n=40; and the axial flow pump was 0.131±0.030g/100L, n=40 respectively; The mean fibrinogen decreases of two pumps between half of an hour were 4.281±2.098mg/100L and 9.625±5.630mg/100L(n=40). So we can conclude that the damage of the spiral pump to blood was less than the axial flow pump. (P<0.05).

A New Magnetic Sealless Coupling Axial Flow Blood Pump

For rotating blood pump, the sealing problem is a very important one to solve. In this paper, it was introduced that we designed and made a small axial flow pump, applying the magnetic coupling method. The pump consisted of two pump housings, a brushless DC motor, an impeller with five wanes, a pair of magnetic discs, a spacer, an inlet and an outlet areas , bearings, a support frame, and etc. The pump is made of titanium and is 125 mm length, 147 ml volume, total 380g of weight. Performances of outputting, sealing, heat creating and damage to blood by the pump were investigated in vitro experiment. Results showed for external experiment that: (1)The pressure created by the pump was 90 mmHg, the flow rates were 1.2 L/min, 4 L/min, 5.9 L/min and 7.8 L/min correspondingly to 5000 rpm, 6000 rpm, 7000 rpm and 8000rpm rotation speeds. The hydrodynamic performance of the axial flow blood pump was enough to meet a patient need when the blood pump was used as a left ventricular assistant device. (2)The hemolysis test was studied by the normalized index of hemolysis(NIH). The NIH result of the axial flow pump was 0.08 g/100 L. (3)The outside temperature of the pump didnt change obviously in 120 hours of rotation, and the sealing function was very well.

Short term in vivo thrombosis evaluation of FW-Ⅱaxial blood pump for left ventricular assist

Objective To evaluate in vivo antithrombosis property of optimized FW-Ⅱaxial blood pump and provide evidence for future clinical use. Methods A left ventriclepump-descending aorta bypass model was established in five healthy sheep (60 70 kg) and the circulation ofthese sheep was assisted by FW-Ⅱaxial blood pump for 2 weeks. At preoperative and postoperative day 1,2,3,7。

Correlation of Blood Lactate and Mixed Venous Oxygen Saturation in Off-Pump CABG

Aim: To evaluate the correlation of blood lactate and mixed venous oxygen saturation to predict outcome in off-pump coronary artery bypass grafting. Method: This is a randomized study including 30 patients. Blood lactate and mixed venous oxygen saturation were measured in 4 groups of patients—number of grafts, presence or absence of left main coronary artery disease, ejection fraction and serum creatinine. Blood samples were taken before induction, after grafting, on intensive care unit admission, 24 hours and 48 hours after surgery. The measured blood lactate and mixed venous oxygen saturation are compared to assess the outcomes in terms of duration of ventilation and intensive care unit stay. Results: The blood lactate and mixed venous oxygen saturation values increased post operatively but no statistically significant difference in three groups— number of grafts, left main coronary artery disease and ejection fraction. In serum creatinine group, the blood lactate value was found to be statistically significant after grafting in patients with creatinine <1.5 mg/dl, however, there was a significant disparity in numbers. Conclusion: Mixed venous oxygen saturation is a better predictor of morbidity than blood lactate in terms of intensive care unit stay in patients undergoing off pump coronary artery bypass grafting.

主动脉穿刺型轴流血泵折边结构叶轮的数值模拟及溶血分析

为解决血泵因叶顶间隙泄漏而造成溶血和血栓等问题,引入了一种折边不等间距叶轮,采用计算流体力学(computational fluid dynamics, CFD)进行内部流场的数值模拟,并与非折边不等间距叶轮及折边等间距叶轮进行对比分析,研究了它们的内流场动力学特性和血液相容性.结果表明:折边叶片结构血泵避免了叶顶间隙泄漏流的产生,同时折边不等间距叶轮减少了叶轮入口和出口处的回流和涡流,流道内整体切应力低于其他2种叶轮;3种叶轮的溶血指数HI均满足血泵的溶血设计指标,其中,折边不等间距叶轮血泵壁面切应力在0~150 Pa的占比达96.84%,曝光时间相对集中且满足人工血泵设计要求,溶血指数较非折边不等间距叶轮血泵下降了3.50%,较折边等间距叶轮血泵下降了12.50%,溶血性能最优.提出的折边不等间距叶轮血泵可有效降低红细胞破损概率,减少溶血和血栓的发生,可为轴流血泵的结构设计和优化提供一定参考.

胰岛素不同注射方式对糖尿病血糖控制效果的影响研究

目的分析胰岛素不同注射方式对2型糖尿病患者血糖控制情况的影响。方法选取2021年9月—2023年9月安溪县医院收治的186例2型糖尿病患者为研究对象,利用最新统计学软件生成随机序列后将其分为对照组、观察组,各93例。两组研究对象均选用门冬胰岛素治疗,其中对照组注射方式为多次胰岛素皮下注射,观察组注射方式为胰岛素泵持续泵注。对比两组血糖控制情况、胰岛素使用剂量、血糖达标情况以及胰岛β细胞功能。结果观察组空腹血糖、餐后2 h血糖及糖化血红蛋白水平均低于对照组,差异有统计学意义(P均<0.05)。观察组平均每天胰岛素使用量低于对照组,血糖达标时间短于对照组,且在达标即刻使用的胰岛素总量少于对照组,差异有统计学意义(P均<0.05)。观察组胰岛β细胞功能优于对照组,差异有统计学意义(P<0.05)。结论对于2型糖尿病患者,采用胰岛素泵持续泵注这一注射方式,有利于改善血糖、血压及血脂水平,同时改善胰岛β细胞功能,且使用胰岛素剂量更低,能够更快速地达到控糖标准。

T2DM合并冠心病介入治疗术后患者应用胰岛素泵强化降糖疗法的作用价值

目的探究胰岛素泵强化降糖疗法应用于2型糖尿病(type 2 diabetes mellitus,T2DM)合并冠状动脉粥样硬化性心脏病(简称冠心病)介入治疗术后的效果。方法回顾性选取2023年1—12月在四川大学华西厦门医院(研究院)就诊的130例T2DM合并冠心病患者的临床资料,全部患者均选择冠心病介入术治疗,按照术后选用的降糖疗法不同分为对照组(常规胰岛素注射)和研究组(胰岛素泵强化降糖),各65例。比较两组血脂及血糖水平(糖化血红蛋白、餐后2 h血糖、空腹血糖、总胆固醇、甘油三酯)、胰岛功能(胰岛β细胞功能指数、胰岛素抵抗指数)情况。结果治疗前两组血糖、血脂及胰岛功能对比,差异无统计学意义(P均>0.05)。治疗2周后,研究组血糖及血脂指标均低于对照组,差异有统计学意义(P均<0.05)。治疗2周后,与对照组比较,研究组胰岛β细胞功能指数更高,胰岛素抵抗指数更低,差异有统计学意义(P均<0.05)。结论接受介入术的T2DM合并冠心病患者术后降糖中选择胰岛素泵,能够改善患者血脂及血糖水平,提高胰岛功能。

基于FPCB绕组的导管泵用电动机设计及损耗分析

基于无槽无刷直流电动机具有体积小、功率密度高、无齿槽转矩的特点,采用柔性印刷电路板(FPCB)技术设计了一种导管泵用无槽无刷微型直流电动机,提出了基于3D多物理场耦合模型分析方法,对导管泵用无槽无刷微型直流电动机进行了损耗分析和优化设计.结果表明:导管泵用无槽无刷微型直流电动机的铜损占整个电动机损耗的88%左右,是导致电动机发热的主要原因;在温度场仿真中,温度变化会改变电动机损耗,影响电动机输出转矩;在流场仿真模型中,电动机温度会使人体血液温度升高,影响血液相容性;流动的血液会带走部分热量,降低电动机温度;绕组优化后的导管泵用电动机输出转矩得到提高,损耗得以降低.

2型糖尿病患者胰岛素泵强化治疗中标准化护理的应用效果

目的探究标准化护理在2型糖尿病(T2DM)患者胰岛素泵强化治疗期间的应用效果。方法选取2022年12月至2023年12月在本院开展胰岛素泵强化治疗的90例T2DM患者为主要观察对象,按照随机数字表法分成两组,分别有45例。对照组采取常规护理,观察组采取标准化护理。评估两组血糖值、糖尿病自我管理行为量表(SDSCA)评分、糖尿病特异性生存质量量表(A-DQOL)评分改善情况及不良事件控制效果。结果出院首日,两组空腹血糖(FBG)、餐后2 h血糖(2 hPG)均低于干预首日,且观察组FBG、2 hPG均低于对照组(P<0.05)。出院当日,观察组SDSCA总分高于对照组(P<0.05);A-DQOL总分比较,观察组比对照组低(P<0.05)。干预期间不良事件总发生率比较,观察组比对照组低(P<0.05)。结论于T2DM患者胰岛素泵强化治疗期间实施标准化护理,可使其主动改善不利于降糖的行为,提高降糖效果,规避可能影响降糖效果的不利因素,提升其生存质量。

胰岛素泵与胰岛素多次注射对妊娠期糖尿病的治疗效果与安全性比较

目的探究胰岛素泵与胰岛素多次注射对妊娠期糖尿病患者的治疗效果与安全性。方法选取本院24例妊娠期糖尿病患者为研究对象,按照随机数字表法分为两组,各12例。多次注射组患者采取多次皮下注射胰岛素治疗,胰岛素泵组患者采取持续皮下胰岛素输注治疗。比较两组患者用药前后的血糖水平、用药期间低血糖发生率及妊娠结局。结果用药前,两组患者血糖水平比较差异无统计学意义(P>0.05)。用药后,胰岛素泵组患者的空腹血糖、餐后2h血糖、糖化血红蛋白水平明显低于多次注射组患者,差异有统计学意义(P<0.05)。两组患者胎膜早破发生率比较差异无统计学意义(P>0.05)。胰岛素泵组患者用药期间低血糖发生率低于多次注射组患者,自然分娩率高于多次注射组,差异有统计学意义(P<0.05)。结论相较于胰岛素多次注射给药,胰岛素泵给药能够有效控制妊娠期糖尿病患者的血糖水平,不良反应发生率更低,可以提高自然分娩率,具有较高的临床应用与推广价值。