Evaluation of the coefficient of lateral stress at rest of granular materials under repetitive loading conditions

Although the internal stress state of soils can be affected by repetitive loading,there are few studies evaluating the lateral stress(or K_(0))of soils under repetitive loading.This study investigates the changes in K_(0) and directional shear wave velocity(V_(s))in samples of two granular materials with different particle shapes during repetitive loading.A modified oedometer cell equipped with bender elements and a diaphragm transducer was developed to measure the variations in the lateral stress and the shear wave velocity,under repetitive loading on the loading and unloading paths.The study produced the following results:(1)Repetitive loading on the loading path resulted in an increase in the K_(0) of test samples as a function of cyclic loading number(i),and(2)Repetitive loading on the unloading path resulted in a decrease in K_(0) according to i.The shear wave velocity ratio(i.e.V_(s)(HH)/V_(s)(VH),where the first and second letters in parentheses corresponds to the directions of wave propagation and particle motion,respectively,and V and H corresponds to the vertical and horizontal directions,respectively)according to i supports the experimental observations of this study.However,when the tested material was in lightly over-consolidated state,there was an increase in K_(0) during repetitive loading,indicating that it was the initial K_(0),rather than the loading path,which is responsible for the change in K_(0).The power model can capture the variation in the K_(0) of samples according to i.Notably,the K_(0)=1 line acts as the boundary between the increase and decrease in K_(0) under repetitive loading.

Tomography of the dynamic stress coefficient for stress wave prediction in sedimentary rock layer under the mining additional stress

In this study,the tomography of dynamic stress coefficient(TDSC)was established based on a mechanical model of stress wave propagation in bedding planes and a mathematical model of the stress wave attenuation in rock masses.The reliability of the TDSC was verified by a linear bedding plane model and field monitoring.Generally,the TDSC in the dynamic stress propagation of bedding planes increases with the following conditions:(1)the increase of the normal stiffness of the bedding plane,(2)the increase of the incident angle of the stress wave,(3)the decrease of the incident frequency of the stress wave,or(4)the growth of three ratios(the ratios of rock densities,elastic moduli,and the Poisson’s ratios)of rocks on either side of bedding planes.The additional stress weakens TDSC linearly and slowly during the stress wave propagation in bedding planes,and the weakening effect increases with the growth of the three ratios.Besides,the TDSC decreases exponentially in the rock mass as propagation distance increases.In a field case,the TDSC decreases significantly as vertical and horizontal distances increase and its wave range increases as vertical distance increases in the sedimentary rock layers.

THEORETICAL MODEL OF EFFECTIVE STRESS COEFFICIENT FOR ROCK/SOIL-LIKE POROUS MATERIALS

Physical mechanisms and influencing factors on the effective stress coefficient for rock/soil-like porous materials are investigated, based on which equivalent connectivity index is proposed. The equivalent connectivity index, relying on the meso-scale structure of porous material and the property of liquid, denotes the connectivity of pores in Representative Element Area （REA）. If the conductivity of the porous material is anisotropic, the equivalent connectivity index is a second order tensor. Based on the basic theories of continuous mechanics and tensor analysis, relationship between area porosity and volumetric porosity of porous materials is deduced. Then a generalized expression, describing the relation between effective stress coefficient tensor and equivalent connectivity tensor of pores, is proposed, and the expression can be applied to isotropic media and also to anisotropic materials. Furthermore, evolution of porosity and equivalent connectivity index of the pore are studied in the strain space, and the method to determine the corresponding functions in expressions above is proposed using genetic algorithm and genetic programming. Two applications show that the results obtained by the method in this paper perfectly agree with the test data. This paper provides an important theoretical support to the coupled hydro-mechanical research.

Effect of Curing Age on Chloride Diffusion Coefficient of Recycled Aggregate Concrete Subjected to Compressive Stresses

The effect of curing age on chloride diffusion coefficient of recycled aggregate concrete subjected to different compressive stresses was investigated.A compression loading setup was both designed and fabricated.The chloride diffusion coefficients of recycled aggregate concrete under compressive stresses were measured by the rapid chloride ion migration(RCM)method.The experimental results show that the chloride diffusion coefficients of recycled aggregate concrete(RAC)under different compressive stress ratios generally decrease with the increase of curing age.For RAC subjected to the same compressive stress ratios,the chloride diffusion coefficients approximately have power functions with curing ages and the relationship models are proposed.Moreover,the influence of curing age on chloride diffusion coefficient firstly decreases and then increases as the compressive stress ratio increases.

Impacts of Wave and Current on Drag Coefficient and Wind Stress over the Tropical and Northern Pacific

By taking into consideration the effects of ocean surface wave-induced Stokes drift velocity Un, and current velocity Uc on the drag coefficient, the spatial distributions of drag coefficient and wind stress in 2004 are computed over the tropical and northern Pacific using an empirical drag coefficient parameterization formula based on wave steepness and wind speed. The global ocean current field is generated from the Hybrid Coordinate Ocean Model （HYCOM） and the wave data are generated from Wavewatch Ill （WW3）. The spatial variability of the drag coefficient and wind stress is analyzed. Preliminary results indicate that the ocean surface Stokes drift velocity and current velocity exert an important influence on the wind stress. The results also show that consideration of the effects of the ocean surface Stokes drift velocity and current velocity on the wind stress can significantly improve the modeling of ocean circulation and air-sea interaction processes.

Effect of non-uniform swelling on coal multiphysics during gas injection: The triangle approach

In current dual porosity/permeability models,there exists a fundamental assumption that the adsorption-induced swelling is distributed uniformly within the representative elementary volume (REV),irrespective of its internal structures and transient processes.However,both internal structures and transient processes can lead to the non-uniform swelling.In this study,we hypothesize that the non-uniform swelling is responsible for why coal permeability in experimental measurements is not only controlled by the effective stress but also is affected by the adsorption-induced swelling.We propose a concept of the swelling triangle composed of swelling paths to characterize the evolution of the non-uniform swelling and serve as a core link in coupled multiphysics.A swelling path is determined by a dimensionless volumetric ratio and a dimensionless swelling ratio.Different swelling paths have the same start and end point,and each swelling path represents a unique swelling case.The swelling path as the diagonal of the triangle represents the case of the uniform swelling while that as the two perpendicular boundaries represents the case of the localized swelling.The paths of all intermediate cases populate inside the triangle.The corresponding relations between the swelling path and the response of coal multiphysics are established by a non-uniform swelling coefficient.We define this method as the triangle approach and corresponding models as swelling path-based ones.The proposed concept and models are verified against a long-term experimental measurement of permeability and strains under constant effective stress.Our results demonstrate that during gas injection,coal multiphysics responses have a close dependence on the swelling path,and that in both future experiments and field predictions,this dependence must be considered.

3D digital-image correlation insight into generalized relaxation behavior of sandstone under stress and pore pressure coupling

The occurrence of geological hazards and the instability of geotechnical engineering structures are closely related to the time-dependent behavior of rock.However,the idealization boundary condition for constant stress in creep or constant strain in relaxation is not usually attained in natural geological systems.Therefore,generalized relaxation tests that explore the simultaneous changes of stress and strain with time under different stress levels with constant pore-water pressure are conducted in this study.The results show that in area Ⅰ,area Ⅱ,and area Ⅲ,the stress and strain both change synchronously with time and show similar evolutionary laws as the strain-time curve for creep or the stress-time curve for relaxation.When the applied stress level surpasses the δ_(ci) or δ_(cd) threshold,the variations in stress and strain and their respective rates of change exhibit a significant increase.The radial deformation and its rate of change exhibit greater sensitivity in response to stress levels.The apparent strain deforms homogeneously at the primary stage,and subsequently,gradually localizes due to the microcrack development at the secondary stage.Ultimately,interconnection of the microcracks causes the formation of a shear-localization zone at the tertiary stage.The strain-time responses inside and outside the localization zone are characterized by local strain accumulation and inelastic unloading during the secondary and tertiary stages,respectively.The width of the shear-localization zone is found to range from 4.43 mm to 7.08 mm and increased with a longer time-to-failure.Scanning electron microscopy(SEM)reveals a dominant coalescence of intergranular cracks on the fracture surface,and the degree of physiochemical deterioration caused by water-rock interaction is more severe under a longer lifetime.The brittle sandstone’s time-dependent deformation is essentially controlled by microcrack development during generalized relaxation,and its expectancy-life is determined by its initial microstructural state and the rheological path.

Mechanical response and dilatancy characteristics of deep marble under different stress paths:A sight from energy dissipation

Dilatancy is a fundamental volumetric growth behavior observed during loading and serves as a key index to comprehending the intricate nonlinear behavior and constitutive equation structure of rock.This study focuses on Jinping marble obtained from the Jinping Underground Laboratory in China at a depth of 2400 m.Various uniaxial and triaxial tests at different strain rates,along with constant confining pressure tests and reduced confining pressure tests under different confining pressures were conducted to analyze the mechanical response and dilatancy characteristics of the marble under four stress paths.Subsequently,a new empirical dilatancy coefficient is proposed based on the energy dissipation method.The results show that brittle failure characteristics of marble under uniaxial compression are more obvious with the strain rate increasing,and plastic failure characteristics of marble under triaxial compression are gradually strengthened.Furthermore,compared to the constant confining pressure,the volume expansion is relatively lower under unloading condition.The energy dissipation is closely linked to the process of dilatancy,with a rapid increase of dissipated energy coinciding with the beginning of dilatancy.A new empirical dilatancy coefficient is defined according to the change trend of energy dissipation rate curve,of which change trend is consistent with the actual dilatancy response in marble under different stress paths.The existing empirical and theoretical dilatancy models are analyzed,which shows that the empirical dilatancy coefficient based on the energy background is more universal.

Performance of water-coupled charge blasting under different in-situ stresses

Water-coupled charge blasting is a promising technique to efficiently break rock masses.In this study,numerical models of double boreholes with water-coupled charge are established using LS-DYNA and are calibrated by the tests of rock masses subjected to explosion loads to examine its performance.The crack levels of rock mass induced by water-coupled charge blasting and air-coupled charge blasting are first compared.It is found that water-coupled charge blasting is more appropriate to fracture deep rock mass than air-coupled charge blasting.In addition,the effects of rock properties,water-coupled charge coefficients,and borehole connection angles on the performance of water-coupled charge blasting are investigated.The results show that rock properties and water-coupled charge coefficients can greatly influence the crack and fragmentation levels of rock mass induced by water-coupled charge blasting under uniform and non-uniform in-situ stresses.However,changing borehole-connection angles can only affect crack and fragmentation levels of rock mass under non-uniform in-situ stresses but barely affect those under uniform in-situ stresses.A formula is finally proposed by considering the above-mentioned factors to provide the design suggestion of water-coupled charge blasting to fracture rock mass with different in-situ stresses.

THE TEMPERATURE STRESS OF RC CONCRETE COMPONENT INDUCED BY LINEAR EXPENSION COEFFICIENT DIFFERENCE

The temperature stress of reinforced concrete component caused by different linear expension coefficient has been discussed in this paper from the point of view of composite materials, The temperature dress can reach about 22 to 45 percent of the tension strength for the concrete with low grade and high ratio of reinforcement which should be considered seriously.

The coefficient of variation representing the non-uniformity of the strain field and its implication to detect earthquake precursor

Before the major earthquake or rock damage occurs,it is often accompanied by a sudden change in the degree of non-uniformity of the strain field.In order to find a stronger non-uniformity signal before the rock failure,the coefficient of variation(Cv)is examined and reformed in this study.We test the Cv calculation way of the"normal-abnormal"model proposed in the previous studies.Based on the analysis of the physical process of rock failure and its relationship to the shear strain field,we construct a new way to calculate the Cv value.The variation of shear strain field on rock sample with the increase of stress is obtained by the digital speckle correlation method(DSCM).The new Cv value calculation way is used to study the non-uniformity of the spatial distribution for the shear strain field.The results show that this Cv calculation way can get more obvious abnormal signals.When the number of observation points are limited,the specific distribution of points can increase the signal strength,which may provide reference for the research on precursor detection of earthquakes.

Stress concentration coefficients of optimized cope-hole welded detail

The fatigue performance of optimized welded detail has been investigated by fatigue experiments of three welded specimens under different loadings.In addition,local finite element models of this welded detail were established using finite element software ANSYS.The influences of different factors such as plate thickness,plate gap and initial geometric imperfections on the stress concentration coefficient(SCC) were discussed.The experimental results indicate that the fatigue life of three specimens for this welded detail is 736,000,1,044,200 and 1,920,300 times,respectively.The web thickness,the filler plate thickness and the initial geometric imperfection have relatively less effect on the SCCs of this welded detail.However,cope-hole radius is influential on the SCCs of the web and the weld.The SCC of weld is significantly affected by the weld size and plate gap,but the SCCs of other parts of the welded detail are hardly affected by the plate gap.

Determination of the Thermal Expansion Coefficient of Concrete at Early Ages by Using Temperature-stress Testing Machine

By using the uptodate temperatuer-stress testing machine, the thermal expansion coefficient of concrete at early ages was studied and indicative conclusions were achieved ： temperature rising due to hydration heat is not directly correlated with cracking, but the temperature and stress evolation process should be taken into consideration in the same time. Proper chemical admixtures and mineral cornpasitions can improve the mechanical properties of concrete such as thermal expansion coefficient, which is very indicative in practice.

Coefficient of thermal expansion of stressed thin films

A new technique was proposed to determine the coefficient of thermal expansion (CTE) of thin films at low temperature. Different pre-stress could be applied and the elastic modulus of materials at different temperatures was measured with CTE simultaneously to eliminate the influence of mechanical deformation caused by the pre-stress. By using this technique, the CTEs of polyimide/silica nanocomposite films with different silica doping levels were experimentally studied at temperature from 77 K to 287 K, and some characteristics related to this new technique were discussed.

A Magentoelectric Coefficient Measurement System with a Free-Stress Sample Holder

With less extra stress on the testing sample, a free-stress sample holder was designed to place the sample horizontally. With the free-stress sample holder, a magnetoelectric (ME) coefficient measurement system was developed based on dynamic method. This measurement system has the hardware part and the software part, integrated by the DC magnetic field generation module, the AC magnetic field generation module, the induced ME voltage detecting module and PC software module. Then, a sample of Terfenol-D/PZT/Terfenol-D trilayer was designed and fabricated, and the relationships of its ME coefficient influenced by the DC magnetic field and the frequency of the AC magnetic field were tested using the measurement system. And the results showed that the free-stress sample holder was proven to improve the accuracy of the measurement system by less stress interference.

Effect of non-uniform stress characteristics on stress measurement in specimen

There is a remarkable difference in stress distribution between a specimen and a plate removed from the specimen.The plate presents a uniform stress distribution whereas the specimen presents a non-uniform stress distribution.Firstly,the real stress distributions in plates with thickness of 30,40 and 50 mm and then in the specimens were obtained through simulation and X-ray surface stress measurement.Secondly,in order to study the impact of specimens shapes and processing ways on the results accuracy,two irregular shapes (parallelogram and trapezoid) and two processing ways (saw and electron discharge machining (EDM)) were compared and analyzed by simulation and experiment using layer removal method,then the specimen effects on measurement results were evaluated.The results show that:1) the non-uniform stress distribution characteristics of the specimen near the surface of the cut is significant,the range of non-uniform stress distribution is approximately one-thickness distance away from the cut,and it decreases gradually along the depth;2) In order to ensure the stability in the results,it is suitable to take the specimen plane size 2-3 times of its thickness;3) Conventional processing methods have little effect on experimental results and the average deviation is less than 5%.

Stress analytical solution for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform distributed pressure

The stress state around circular openings,such as boreholes,shafts,and tunnels,is usually needed to be evaluated.Solutions for stresses,strains and ultimate bearing capacities of pressurized hollow cylinder are common cases.Stress analytical method for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform pressure on the outer surface and uniform radial pressure on the inner surface is given.The power series method of complex function is used.The stress analytical solution is obtained with the assumption that two layers of a cylinder are fully contacted.The distributions of normal and tangential contact stress along the interface,tangential stress on the inner boundary and stresses in the radial direction at θ=0°,45° and 90°,are obtained.An example indicates that,when the elastic modulus of the inner layer of a double-layered thick-walled cylinder is smaller than that of the outer layer,the tangential stress is smaller than that in the corresponding point for a traditional cylinder composed of homogeneous materials.In that way,stress concentration at the inner surface can be alleviated and the stress distribution is more uniform.This is a capable way to enhance the elastic ultimate bearing capacity of thick-walled cylinder.

Forced Axial and Torsional Vibrations of a Shaft Line Using the Transfer Matrix Method Related to Solution Coefficients

This present paper deals with a mathematical description of linear axial and torsional vibrations. The normal and tangential stress tensor components produced by axial-torsional deformations and vibrations in the propeller and intermediate shafts, under the influence of propeller-induced static and variable hydrodynamic excitations are also studied. The transfer matrix method related to the constant coefficients of differential equation solutions is used. The advantage of the latter as compared with a well-known method of transfer matrix associated with state vector is the possibility of reducing the number of multiplied matrices when adjacent shaft segments have the same material properties and diameters. The results show that there is no risk of buckling and confirm that the strength of the shaft line depends on the value of the static tangential stresses which is the most important component of the stress tensor.

Inverse approach to determine piston profile from impact stress waveform on given non-uniform rod

An essential problem in the design of mechanical impact systems is the impact of a piston on a rod. The impact of a semi finite cylindrical piston on a non uniform rod was studied. Based on wave mechanics and characteristic line theory, an inverse numerical approach to determine the piston profile was proposed, by means of which the geometry of an impact piston may be determined from the given stress waveform for a given rod profile. Numerical results show that the given stress waveform may be produced by means of the alternatives of design of piston and rod. There is good agreement between the experimental results and numerical results. [

Monitoring the change in horizontal stress with multi-wave time-lapse seismic response based on nonlinear elasticity theory

Monitoring the change in horizontal stress from the geophysical data is a tough challenge, and it has a crucial impact on broad practical scenarios which involve reservoir exploration and development, carbon dioxide (CO_(2)) injection and storage, shallow surface prospecting and deep-earth structure description. The change in in-situ stress induced by hydrocarbon production and localized tectonic movements causes the changes in rock mechanic properties (e.g. wave velocities, density and anisotropy) and further causes the changes in seismic amplitudes, phases and travel times. In this study, the nonlinear elasticity theory that regards the rock skeleton (solid phase) and pore fluid as an effective whole is used to characterize the effect of horizontal principal stress on rock overall elastic properties and the stress-dependent anisotropy parameters are therefore formulated. Then the approximate P-wave, SV-wave and SH-wave angle-dependent reflection coefficient equations for the horizontal-stress-induced anisotropic media are proposed. It is shown that, on the different reflectors, the stress-induced relative changes in reflectivities (i.e., relative difference) of elastic parameters (i.e., P- and S-wave velocities and density) are much less than the changes in contrasts of anisotropy parameters. Therefore, the effects of stress change on the reflectivities of three elastic parameters are reasonably neglected to further propose an AVO inversion approach incorporating P-, SH- and SV-wave information to estimate the change in horizontal principal stress from the corresponding time-lapse seismic data. Compared with the existing methods, our method eliminates the need for man-made rock-physical or fitting parameters, providing more stable predictive power. 1D test illustrates that the estimated result from time-lapse P-wave reflection data shows the most reasonable agreement with the real model, while the estimated result from SH-wave reflection data shows the largest bias. 2D test illustrates the feasibility of the proposed inversion method for estimating the change in horizontal stress from P-wave time-lapse seismic data.