The stress state around circular openings,such as boreholes,shafts,and tunnels,is usually needed to be evaluated.Solutions for stresses,strains and ultimate bearing capacities of pressurized hollow cylinder are common...The stress state around circular openings,such as boreholes,shafts,and tunnels,is usually needed to be evaluated.Solutions for stresses,strains and ultimate bearing capacities of pressurized hollow cylinder are common cases.Stress analytical method for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform pressure on the outer surface and uniform radial pressure on the inner surface is given.The power series method of complex function is used.The stress analytical solution is obtained with the assumption that two layers of a cylinder are fully contacted.The distributions of normal and tangential contact stress along the interface,tangential stress on the inner boundary and stresses in the radial direction at θ=0°,45° and 90°,are obtained.An example indicates that,when the elastic modulus of the inner layer of a double-layered thick-walled cylinder is smaller than that of the outer layer,the tangential stress is smaller than that in the corresponding point for a traditional cylinder composed of homogeneous materials.In that way,stress concentration at the inner surface can be alleviated and the stress distribution is more uniform.This is a capable way to enhance the elastic ultimate bearing capacity of thick-walled cylinder.展开更多
There is a remarkable difference in stress distribution between a specimen and a plate removed from the specimen.The plate presents a uniform stress distribution whereas the specimen presents a non-uniform stress dist...There is a remarkable difference in stress distribution between a specimen and a plate removed from the specimen.The plate presents a uniform stress distribution whereas the specimen presents a non-uniform stress distribution.Firstly,the real stress distributions in plates with thickness of 30,40 and 50 mm and then in the specimens were obtained through simulation and X-ray surface stress measurement.Secondly,in order to study the impact of specimens shapes and processing ways on the results accuracy,two irregular shapes (parallelogram and trapezoid) and two processing ways (saw and electron discharge machining (EDM)) were compared and analyzed by simulation and experiment using layer removal method,then the specimen effects on measurement results were evaluated.The results show that:1) the non-uniform stress distribution characteristics of the specimen near the surface of the cut is significant,the range of non-uniform stress distribution is approximately one-thickness distance away from the cut,and it decreases gradually along the depth;2) In order to ensure the stability in the results,it is suitable to take the specimen plane size 2-3 times of its thickness;3) Conventional processing methods have little effect on experimental results and the average deviation is less than 5%.展开更多
Deposition patterns can significantly affect residual stress distribution in additive manufacturing processes.In this paper,a novel pattern,the S-pattern,is proposed for the metal additive manufacturing process.The fi...Deposition patterns can significantly affect residual stress distribution in additive manufacturing processes.In this paper,a novel pattern,the S-pattern,is proposed for the metal additive manufacturing process.The finite element method is used to study the temperature field and the stress field of a cuboid structure under the S-pattern and five other representative patterns:zig-zag,raster,alternate-line,in-out spiral,and out-in spiral.The results show that the S-pattern achieves the lowest values of both equivalent residual stress and maximum principal residual stress,and the warpage of the S-pattern is close to that of counterparts.By analyzing the temperature and stress fields under all patterns,it is found that the residual stress distribution is determined by the uniformity of temperature distribution which is correlated with the peak temperatures of corners.The equivalent residual stress and the maximum principal residual stress are inversely correlated with the average peak temperature and the minimum peak temperature of corners,respectively.These correlations between temperature and residual stress provide an effective approach to evaluate the residual stress of different patterns and guide the deposition process in practice.展开更多
基金Projects(50874047,51074014,51174014)supported by the National Natural Science Foundation of China
文摘The stress state around circular openings,such as boreholes,shafts,and tunnels,is usually needed to be evaluated.Solutions for stresses,strains and ultimate bearing capacities of pressurized hollow cylinder are common cases.Stress analytical method for plane problem of a double-layered thick-walled cylinder subjected to a type of non-uniform pressure on the outer surface and uniform radial pressure on the inner surface is given.The power series method of complex function is used.The stress analytical solution is obtained with the assumption that two layers of a cylinder are fully contacted.The distributions of normal and tangential contact stress along the interface,tangential stress on the inner boundary and stresses in the radial direction at θ=0°,45° and 90°,are obtained.An example indicates that,when the elastic modulus of the inner layer of a double-layered thick-walled cylinder is smaller than that of the outer layer,the tangential stress is smaller than that in the corresponding point for a traditional cylinder composed of homogeneous materials.In that way,stress concentration at the inner surface can be alleviated and the stress distribution is more uniform.This is a capable way to enhance the elastic ultimate bearing capacity of thick-walled cylinder.
基金Project(2005CB623708) supported by the National Basic Research Program of China
文摘There is a remarkable difference in stress distribution between a specimen and a plate removed from the specimen.The plate presents a uniform stress distribution whereas the specimen presents a non-uniform stress distribution.Firstly,the real stress distributions in plates with thickness of 30,40 and 50 mm and then in the specimens were obtained through simulation and X-ray surface stress measurement.Secondly,in order to study the impact of specimens shapes and processing ways on the results accuracy,two irregular shapes (parallelogram and trapezoid) and two processing ways (saw and electron discharge machining (EDM)) were compared and analyzed by simulation and experiment using layer removal method,then the specimen effects on measurement results were evaluated.The results show that:1) the non-uniform stress distribution characteristics of the specimen near the surface of the cut is significant,the range of non-uniform stress distribution is approximately one-thickness distance away from the cut,and it decreases gradually along the depth;2) In order to ensure the stability in the results,it is suitable to take the specimen plane size 2-3 times of its thickness;3) Conventional processing methods have little effect on experimental results and the average deviation is less than 5%.
基金funded by the Chinese Scholarship Council and the Research Council of Norway through the Petromaks2 program(Project No.281927)the BIA Program(Project No.269558)。
文摘Deposition patterns can significantly affect residual stress distribution in additive manufacturing processes.In this paper,a novel pattern,the S-pattern,is proposed for the metal additive manufacturing process.The finite element method is used to study the temperature field and the stress field of a cuboid structure under the S-pattern and five other representative patterns:zig-zag,raster,alternate-line,in-out spiral,and out-in spiral.The results show that the S-pattern achieves the lowest values of both equivalent residual stress and maximum principal residual stress,and the warpage of the S-pattern is close to that of counterparts.By analyzing the temperature and stress fields under all patterns,it is found that the residual stress distribution is determined by the uniformity of temperature distribution which is correlated with the peak temperatures of corners.The equivalent residual stress and the maximum principal residual stress are inversely correlated with the average peak temperature and the minimum peak temperature of corners,respectively.These correlations between temperature and residual stress provide an effective approach to evaluate the residual stress of different patterns and guide the deposition process in practice.
