Methods of digital human modeling have been developed and utilized to reflect human shape features.However,most of published works focused on dynamic visualization or fashion design,instead of high-accuracy modeling,w...Methods of digital human modeling have been developed and utilized to reflect human shape features.However,most of published works focused on dynamic visualization or fashion design,instead of high-accuracy modeling,which was strongly demanded by medical or rehabilitation scenarios.Prior to a high-accuracy modeling of human legs based on non-uniform rational B-splines(NURBS),the method of extracting the required quasi-grid network of feature points for human legs is presented in this work.Given the 3 D scanned human body,the leg is firstly segmented and put in standardized position.Then re-sampling of the leg is conducted via a set of equidistant cross sections.Through analysis of leg circumferences and circumferential curvature,the characteristic sections of the leg as well as the characteristic points on the sections are then identified according to the human anatomy and shape features.The obtained collection can be arranged to form a grid of data points for knots calculation and high-accuracy shape reconstruction in future work.展开更多
Abstract For two rational quadratic B spline curves with same control vertexes, the cross ratio of four collinear points are represented: which are any one of the vertexes, and the two points that the ray initialing f...Abstract For two rational quadratic B spline curves with same control vertexes, the cross ratio of four collinear points are represented: which are any one of the vertexes, and the two points that the ray initialing from the vertex intersects with the corresponding segments of the two curves, and the point the ray intersecting with the connecting line between the two neighboring vertexes. Different from rational quadratic Bézier curves, the value is generally related with the location of the ray, and the necessary and sufficient condition of the ratio being independent of the ray's location is showed. Also another cross ratio of the following four collinear points are suggested, i.e. one vertex, the points that the ray from the initial vertex intersects respectively with the curve segment, the line connecting the segments end points, and the line connecting the two neighboring vertexes. This cross ratio is concerned only with the ray's location, but not with the weights of the curve. Furthermore, the cross ratio is projective invariant under the projective transformation between the two segments.展开更多
A new approach for NURBS(Non-uniform rational B-spline) curve and surface fitting for measured points was presented which employs a fairing method applied to digitized point data with discrete curvature. If measured p...A new approach for NURBS(Non-uniform rational B-spline) curve and surface fitting for measured points was presented which employs a fairing method applied to digitized point data with discrete curvature. If measured points are used as control points to construct an NURBS curve, then the curvature of each data point corresponding to control point of the constructed curve can be computed. According to the convex hull and local properties of NURBS, based on the curvatures obtained, the measured points can be faired. If faired measured points are used as target points to modify, the constructed curve passing through these faired points can produce a smooth NURBS curve. This paper also presented the justification for utilizing the curvatures of constructed NURBS curve instead of the conventional interpolated curve to fair the measured points. Based on the presented algorithms, some qualities of the constructed curves can be improved.展开更多
In this paper, based on the idea of profit and loss modification, we presentthe iterative non-uniform B-spline curve and surface to settle a key problem in computeraided geometric design and reverse engineering, that ...In this paper, based on the idea of profit and loss modification, we presentthe iterative non-uniform B-spline curve and surface to settle a key problem in computeraided geometric design and reverse engineering, that is, constructing the curve (surface)fitting (interpolating) a given ordered point set without solving a linear system. We startwith a piece of initial non-uniform B-spline curve (surface) which takes the given point setas its control point set. Then by adjusting its control points gradually with iterative formula,we can get a group of non-uniform B-spline curves (surfaces) with gradually higherprecision. In this paper, using modern matrix theory, we strictly prove that the limit curve(surface) of the iteration interpolates the given point set. The non-uniform B-spline curves(surfaces) generated with the iteration have many advantages, such as satisfying theNURBS standard, having explicit expression, gaining locality, and convexity preserving,etc展开更多
This paper presents a flexible method for the representation of welded seam based on spline interpolation. In this method, the tool path of welding robot can be generated automatically from a 3D CAD model. This techni...This paper presents a flexible method for the representation of welded seam based on spline interpolation. In this method, the tool path of welding robot can be generated automatically from a 3D CAD model. This technique has been implemented and demonstrated in the FANUC Arc Welding Robot Workstation. According to the method, a software system is developed using VBA of SolidWorks 2006. It offers an interface between SolidWorks and ROBOGUIDE, the off-line programming software of FANUC robot. It combines the strong modeling function of the former and the simulating function of the latter. It also has the capability of with on-line robot. The result data have shown its high accuracy and strong reliability in experiments. This method will improve the intelligence and the flexibility of the welding robot workstation.展开更多
In recent years, high-altitude aerostats have been increasingly developed in the direction of multi-functionality and large size. Due to the large size and the high flexibility, new challenges for large aerostats have...In recent years, high-altitude aerostats have been increasingly developed in the direction of multi-functionality and large size. Due to the large size and the high flexibility, new challenges for large aerostats have appeared in the configuration test and the deformation analysis. The methods of the configuration test and the deformation analysis for large airship have been researched and discussed. A tested method of the configuration,named internal scanning, is established to quickly obtain the spatial information of all surfaces for the large airship by the three-dimensional(3D) laser scanning technology. By using the surface wrap method, the configuration parameters of the large airship are calculated. According to the test data of the configuration, the structural dimensions such as the distances between the characteristic sections are measured. The method of the deformation analysis for the airship contains the algorithm of nonuniform rational B-splines(NURBS) and the finite element(FE)method. The algorithm of NURBS is used to obtain the reconfiguration model of the large airship. The seams are considered and the seam areas are divided. The FE model of the middle part of the large airship is established. The distributions of the stress and the strain for the large airship are obtained by the FE method. The position of the larger deformation for the airship is found.展开更多
A new method for recovering shape from cross-sectional contours with complexbranching structures is presented. First, each branching problem by providing an intermediatecontour using distance function and image proces...A new method for recovering shape from cross-sectional contours with complexbranching structures is presented. First, each branching problem by providing an intermediatecontour using distance function and image processing technology is solved. Then, all contours aredivided into several groups of simple contours. For each group, a NURBS curve is fitted to contourpoints in each section within a given accuracy on a common knot vector. Finally, the NURBS surfaceskinning of these contours is performed for providing a smooth geometric model. The method issuitable to reproduce the object by NC machining or rapid prototyping. Some results demonstrate itsusefulness and feasibility.展开更多
This paper presents a novel algorithm for planar curve offsetting. The basic idea is to regard the locus relative to initial base circle, which is formed by moving the unit normal vectors of the base curve, as a unit ...This paper presents a novel algorithm for planar curve offsetting. The basic idea is to regard the locus relative to initial base circle, which is formed by moving the unit normal vectors of the base curve, as a unit circular arc first, then accurately to represent it as a rational curve, and finally to reparameterize it in a particular way to approximate the offset. Examples illustrated that the algorithm yields fewer curve segments and control points as well as C^1 continuity, and so has much significance in terms of saving computing time, reducing the data storage and smoothing curves entirely.展开更多
To overcome the topological constraints of non-uniform rational B-splines,T-splines have been proposed to define the freeform surfaces.The introduction of T-junctions and extraordinary points makes it possible to repr...To overcome the topological constraints of non-uniform rational B-splines,T-splines have been proposed to define the freeform surfaces.The introduction of T-junctions and extraordinary points makes it possible to represent arbitrarily shaped models by a single T-spline surface.Whereas,the complexity and flexibility of topology structure bring difficulty in programming,which have caused a great obstacle for the development and application of T-spline technologies.So far,research literatures concerning T-spline data structures compatible with extraordinary points are very scarce.In this paper,an efficient data structure for calculation of unstructured T-spline surfaces is developed,by which any complex T-spline surface models can be easily and efficiently computed.Several unstructured T-spline surface models are calculated and visualized in our prototype system to verify the validity of the proposed method.展开更多
In the paper [1], the geometrical mapping techniques based on Non-Uniform Rational B-Spline (NURBS) were introduced to solve an elliptic boundary value problem containing a singularity. In the mapping techniques, the ...In the paper [1], the geometrical mapping techniques based on Non-Uniform Rational B-Spline (NURBS) were introduced to solve an elliptic boundary value problem containing a singularity. In the mapping techniques, the inverse function of the NURBS geometrical mapping generates singular functions as well as smooth functions by an unconventional choice of control points. It means that the push-forward of the NURBS geometrical mapping that generates singular functions, becomes a piecewise smooth function. However, the mapping method proposed is not able to catch singularities emerging at multiple locations in a domain. Thus, we design the geometrical mapping that generates singular functions for each singular zone in the physical domain. In the design of the geometrical mapping, we should consider the design of control points on the interface between/among patches so that global basis functions are in C0?space. Also, we modify the B-spline functions whose supports include the interface between/among them. We put the idea in practice by solving elliptic boundary value problems containing multiple singularities.展开更多
A method to reparametrize G retional curve to obtain a C^1 curve is given. A practical G^1 continual connective between adjacent NURUS patches along common guadratic boundary curve is presented in this paper, and a s...A method to reparametrize G retional curve to obtain a C^1 curve is given. A practical G^1 continual connective between adjacent NURUS patches along common guadratic boundary curve is presented in this paper, and a specific algorithm for control points and weights of NURBS patches is discussed.展开更多
A digital model is presented for the purpose of design, manufacture and measurement of hypoid gear, based on the non-uniform rational B-spline surface (NURBS) method. The digital model and the function-oriented acti...A digital model is presented for the purpose of design, manufacture and measurement of hypoid gear, based on the non-uniform rational B-spline surface (NURBS) method. The digital model and the function-oriented active design technique are combined to form a new design method for hypoid gears. The method is well adaptable to CNC bevel gear cutting machines and CNC-controlled gear inspection machines, and can be used to create the initial machine tool cutting location data or program measurement path. The presented example verifies the method is correct.展开更多
In this paper, we establish a mathematical model of the forest fire spread process based on a partial differential equation. We describe the distribution of time field and velocity field in the whole two-dimensional s...In this paper, we establish a mathematical model of the forest fire spread process based on a partial differential equation. We describe the distribution of time field and velocity field in the whole two-dimensional space by vector field theory. And we obtain a continuous algorithm to predict the dynamic behavior of forest fire spread in a short time. We use the algorithm to interpolate the fire boundary by cubic non-uniform rational B-spline closed curve. The fire boundary curve at any time can be simulated by solving the Eikonal equation. The model is tested in theory and in practice. The results show that the model has good accuracy and stability, and it’s compatible with most of the existing models, such as the elliptic model and the cellular automata model.展开更多
Feedrate scheduling in computer numerical control(CNC)machining is of great importance to fully develop the capabilities of machine tools while maintaining the motion stability of each actuator.Smooth and time-optimal...Feedrate scheduling in computer numerical control(CNC)machining is of great importance to fully develop the capabilities of machine tools while maintaining the motion stability of each actuator.Smooth and time-optimal feedrate scheduling plays a critical role in improving the machining efficiency and precision of complex surfaces considering the irregular curvature characteristics of tool paths and the limited drive capacities of machine tools.This study develops a general feedrate scheduling method for non-uniform rational B-splines(NURBS)tool paths in CNC machining aiming at minimizing the total machining time without sacrificing the smoothness of feed motion.The feedrate profile is represented by a B-spline curve to flexibly adapt to the frequent acceleration and deceleration requirements of machining along complex tool paths.The time-optimal B-spline feedrate is produced by continuously increasing the control points sequentially from zero positions in the bidirectional scanning and sampling processes.The required number of knots for the time-optimal B-spline feedrate can be determined using a progressive knot insertion method.To improve the computational efficiency,the B-spline feedrate profile is divided into a series of independent segments and the computation in each segment can be performed concurrently.The proposed feedrate scheduling method is capable of dealing with not only the geometry constraints but also high-order drive constraints for any complex tool path with little computational overhead.Simulations and machining experiments are conducted to verify the effectiveness and superiorities of the proposed method.展开更多
The problem of quick analysis using exact geometry data was proposed by Hughes et al. and the isogeometric analysis framework was introduced as a solution. In this letter, the exact geometry concept is combined into t...The problem of quick analysis using exact geometry data was proposed by Hughes et al. and the isogeometric analysis framework was introduced as a solution. In this letter, the exact geometry concept is combined into the quasi-conforming framework and a novel method, i.e., the exact geometry based quasi-conforming analysis is proposed. In present method the geometry is exactly described by non-uniform rational B-spline bases, while the solution space by traditional polynomial bases. Present method combines the merits of both isogeometric analysis and quasi-conforming finite element method. In this letter Euler-Bernoulli beam problem is solved as an example and the results show that the present method is effective and promising.展开更多
This paper presents an automatic programming system on PC, it has also solved the technic problem in the combination of different curves or surfaces. The NURBS is applied to modeling and fitting complicated curves a...This paper presents an automatic programming system on PC, it has also solved the technic problem in the combination of different curves or surfaces. The NURBS is applied to modeling and fitting complicated curves and surfaces. The circular spline is combined with the NURBS to determine the cutter path in accordance with the features of the interpolation movement of NC machine tool. Three methods have been developed to solve the overcutting problems.展开更多
A desingularized high order panel method based on Non-Uniform Rational B-Spline (NURBS) was developed to deal with three-dimensional potential flow problems. A NURBS surface was used to precisely represent the body ...A desingularized high order panel method based on Non-Uniform Rational B-Spline (NURBS) was developed to deal with three-dimensional potential flow problems. A NURBS surface was used to precisely represent the body geometry. Velocity potential on the body surface was described by the B-spline after the source density distribution on the body surface had been solved. The collocation approach was employed to satisfy the Neurnann boundary condition and Gaussian quadrature points were chosen as both the collocation points and the source points. The singularity was removed by a combined method, so the process of the numerical computation was non-singular. In order to verify the method proposed, the unbounded flow problems of sphere and ellipsoid, the wave-making problem of a submerged ellipsoid were chosen as computational examples. It is shown that the numerical results are in good agreement with analytical solutions and other numerical results in all cases, and sufficient accuracy of numerical solution can be reached with a small number of panels.展开更多
A three-dimensional high-order panel method based on non-uniform rational B-spline(NURBS) is developed for predicting the hydrodynamic interaction forces on a moored ship induced by a passing ship in shallow water. An...A three-dimensional high-order panel method based on non-uniform rational B-spline(NURBS) is developed for predicting the hydrodynamic interaction forces on a moored ship induced by a passing ship in shallow water. An NURBS surface is used to precisely represent the hull geometry. Velocity potential on the hull surface is described by B-spline after the source density distribution on the boundary surface is determined. A collocation approach is applied to the boundary integral equation discretization. Under the assumption of low passing speed, the effect of free surface elevation is neglected in the numerical calculation, and infinite image method is used to deal with the finite water depth effect. The time stepping method is used to solve the velocity potential at each time step. Detailed convergence study with respect to time step, panel size and Green function is undertaken. The present results of hydrodynamic forces are compared with those obtained by slender-body theory to show the validity of the proposed numerical method. Calculations are conducted for different water depths and lateral distances between ships, and the detail results are presented to demonstrate the effects of these factors.展开更多
This paper describes a method for mesh adaptation in the presence of intersections, such as wing-fuselage. Automatic optimization tools, using Computational Fluid Dynamics(CFD) simulations, face the problem to adapt...This paper describes a method for mesh adaptation in the presence of intersections, such as wing-fuselage. Automatic optimization tools, using Computational Fluid Dynamics(CFD) simulations, face the problem to adapt the computational grid upon deformations of the boundary surface. When mesh regeneration is not feasible, due to the high cost to build up the computational grid, mesh deformation techniques are considered a cheap approach to adapt the mesh to changes on the geometry. Mesh adaptation is a well-known subject in the literature; however, there is very little work which deals with moving intersections. Without a proper treatment of the intersections,the use of automatic optimization methods for aircraft design is limited to individual components.The proposed method takes advantage of the CAD description, which usually comes in the form of Non-Uniform Rational B-Splines(NURBS) patches. This paper describes an algorithm to recalculate the intersection line between two parametric surfaces. Then, the surface mesh is adapted to the moving intersection in parametric coordinates. Finally, the deformation is propagated through the volumetric mesh. The proposed method is tested with the DLR F6 wing-body configuration.展开更多
基金National Natural Science Foundation of China(Nos.12002085 and 51603039)Shanghai Pujiang Program,China(No.19PC002)+1 种基金Fundamental Research Funds for the Central Universities,China(No.2232019D3-58)Initial Research Funds for Young Teachers of Donghua University,China(No.104-07-0053088)。
文摘Methods of digital human modeling have been developed and utilized to reflect human shape features.However,most of published works focused on dynamic visualization or fashion design,instead of high-accuracy modeling,which was strongly demanded by medical or rehabilitation scenarios.Prior to a high-accuracy modeling of human legs based on non-uniform rational B-splines(NURBS),the method of extracting the required quasi-grid network of feature points for human legs is presented in this work.Given the 3 D scanned human body,the leg is firstly segmented and put in standardized position.Then re-sampling of the leg is conducted via a set of equidistant cross sections.Through analysis of leg circumferences and circumferential curvature,the characteristic sections of the leg as well as the characteristic points on the sections are then identified according to the human anatomy and shape features.The obtained collection can be arranged to form a grid of data points for knots calculation and high-accuracy shape reconstruction in future work.
文摘Abstract For two rational quadratic B spline curves with same control vertexes, the cross ratio of four collinear points are represented: which are any one of the vertexes, and the two points that the ray initialing from the vertex intersects with the corresponding segments of the two curves, and the point the ray intersecting with the connecting line between the two neighboring vertexes. Different from rational quadratic Bézier curves, the value is generally related with the location of the ray, and the necessary and sufficient condition of the ratio being independent of the ray's location is showed. Also another cross ratio of the following four collinear points are suggested, i.e. one vertex, the points that the ray from the initial vertex intersects respectively with the curve segment, the line connecting the segments end points, and the line connecting the two neighboring vertexes. This cross ratio is concerned only with the ray's location, but not with the weights of the curve. Furthermore, the cross ratio is projective invariant under the projective transformation between the two segments.
基金The Rising Star Project of Shanghai (No.06QA14026) The International Coopera-tion Project of Shanghai (No.41107049)
文摘A new approach for NURBS(Non-uniform rational B-spline) curve and surface fitting for measured points was presented which employs a fairing method applied to digitized point data with discrete curvature. If measured points are used as control points to construct an NURBS curve, then the curvature of each data point corresponding to control point of the constructed curve can be computed. According to the convex hull and local properties of NURBS, based on the curvatures obtained, the measured points can be faired. If faired measured points are used as target points to modify, the constructed curve passing through these faired points can produce a smooth NURBS curve. This paper also presented the justification for utilizing the curvatures of constructed NURBS curve instead of the conventional interpolated curve to fair the measured points. Based on the presented algorithms, some qualities of the constructed curves can be improved.
文摘In this paper, based on the idea of profit and loss modification, we presentthe iterative non-uniform B-spline curve and surface to settle a key problem in computeraided geometric design and reverse engineering, that is, constructing the curve (surface)fitting (interpolating) a given ordered point set without solving a linear system. We startwith a piece of initial non-uniform B-spline curve (surface) which takes the given point setas its control point set. Then by adjusting its control points gradually with iterative formula,we can get a group of non-uniform B-spline curves (surfaces) with gradually higherprecision. In this paper, using modern matrix theory, we strictly prove that the limit curve(surface) of the iteration interpolates the given point set. The non-uniform B-spline curves(surfaces) generated with the iteration have many advantages, such as satisfying theNURBS standard, having explicit expression, gaining locality, and convexity preserving,etc
基金This work was supported by Tianjin Natural Science Fund Supporting Project (05YFJZJ)
文摘This paper presents a flexible method for the representation of welded seam based on spline interpolation. In this method, the tool path of welding robot can be generated automatically from a 3D CAD model. This technique has been implemented and demonstrated in the FANUC Arc Welding Robot Workstation. According to the method, a software system is developed using VBA of SolidWorks 2006. It offers an interface between SolidWorks and ROBOGUIDE, the off-line programming software of FANUC robot. It combines the strong modeling function of the former and the simulating function of the latter. It also has the capability of with on-line robot. The result data have shown its high accuracy and strong reliability in experiments. This method will improve the intelligence and the flexibility of the welding robot workstation.
基金supported by the Foundation for Innovative Research Groups of the National Natural Science Foundation of China (11421091)。
文摘In recent years, high-altitude aerostats have been increasingly developed in the direction of multi-functionality and large size. Due to the large size and the high flexibility, new challenges for large aerostats have appeared in the configuration test and the deformation analysis. The methods of the configuration test and the deformation analysis for large airship have been researched and discussed. A tested method of the configuration,named internal scanning, is established to quickly obtain the spatial information of all surfaces for the large airship by the three-dimensional(3D) laser scanning technology. By using the surface wrap method, the configuration parameters of the large airship are calculated. According to the test data of the configuration, the structural dimensions such as the distances between the characteristic sections are measured. The method of the deformation analysis for the airship contains the algorithm of nonuniform rational B-splines(NURBS) and the finite element(FE)method. The algorithm of NURBS is used to obtain the reconfiguration model of the large airship. The seams are considered and the seam areas are divided. The FE model of the middle part of the large airship is established. The distributions of the stress and the strain for the large airship are obtained by the FE method. The position of the larger deformation for the airship is found.
基金Provincial Natural Science Foundation of Liaoning,China (No.20010102087)
文摘A new method for recovering shape from cross-sectional contours with complexbranching structures is presented. First, each branching problem by providing an intermediatecontour using distance function and image processing technology is solved. Then, all contours aredivided into several groups of simple contours. For each group, a NURBS curve is fitted to contourpoints in each section within a given accuracy on a common knot vector. Finally, the NURBS surfaceskinning of these contours is performed for providing a smooth geometric model. The method issuitable to reproduce the object by NC machining or rapid prototyping. Some results demonstrate itsusefulness and feasibility.
基金Supported by the National Natural Science Foundation of China (6093300760873111)
文摘This paper presents a novel algorithm for planar curve offsetting. The basic idea is to regard the locus relative to initial base circle, which is formed by moving the unit normal vectors of the base curve, as a unit circular arc first, then accurately to represent it as a rational curve, and finally to reparameterize it in a particular way to approximate the offset. Examples illustrated that the algorithm yields fewer curve segments and control points as well as C^1 continuity, and so has much significance in terms of saving computing time, reducing the data storage and smoothing curves entirely.
基金The authors would like to acknowledge the support by the National Natural Science Foundation of China(Nos.61572056 and 51305016).
文摘To overcome the topological constraints of non-uniform rational B-splines,T-splines have been proposed to define the freeform surfaces.The introduction of T-junctions and extraordinary points makes it possible to represent arbitrarily shaped models by a single T-spline surface.Whereas,the complexity and flexibility of topology structure bring difficulty in programming,which have caused a great obstacle for the development and application of T-spline technologies.So far,research literatures concerning T-spline data structures compatible with extraordinary points are very scarce.In this paper,an efficient data structure for calculation of unstructured T-spline surfaces is developed,by which any complex T-spline surface models can be easily and efficiently computed.Several unstructured T-spline surface models are calculated and visualized in our prototype system to verify the validity of the proposed method.
文摘In the paper [1], the geometrical mapping techniques based on Non-Uniform Rational B-Spline (NURBS) were introduced to solve an elliptic boundary value problem containing a singularity. In the mapping techniques, the inverse function of the NURBS geometrical mapping generates singular functions as well as smooth functions by an unconventional choice of control points. It means that the push-forward of the NURBS geometrical mapping that generates singular functions, becomes a piecewise smooth function. However, the mapping method proposed is not able to catch singularities emerging at multiple locations in a domain. Thus, we design the geometrical mapping that generates singular functions for each singular zone in the physical domain. In the design of the geometrical mapping, we should consider the design of control points on the interface between/among patches so that global basis functions are in C0?space. Also, we modify the B-spline functions whose supports include the interface between/among them. We put the idea in practice by solving elliptic boundary value problems containing multiple singularities.
文摘A method to reparametrize G retional curve to obtain a C^1 curve is given. A practical G^1 continual connective between adjacent NURUS patches along common guadratic boundary curve is presented in this paper, and a specific algorithm for control points and weights of NURBS patches is discussed.
基金This project is supported by National Natural Science Foundation of China (NO.59775009)
文摘A digital model is presented for the purpose of design, manufacture and measurement of hypoid gear, based on the non-uniform rational B-spline surface (NURBS) method. The digital model and the function-oriented active design technique are combined to form a new design method for hypoid gears. The method is well adaptable to CNC bevel gear cutting machines and CNC-controlled gear inspection machines, and can be used to create the initial machine tool cutting location data or program measurement path. The presented example verifies the method is correct.
文摘In this paper, we establish a mathematical model of the forest fire spread process based on a partial differential equation. We describe the distribution of time field and velocity field in the whole two-dimensional space by vector field theory. And we obtain a continuous algorithm to predict the dynamic behavior of forest fire spread in a short time. We use the algorithm to interpolate the fire boundary by cubic non-uniform rational B-spline closed curve. The fire boundary curve at any time can be simulated by solving the Eikonal equation. The model is tested in theory and in practice. The results show that the model has good accuracy and stability, and it’s compatible with most of the existing models, such as the elliptic model and the cellular automata model.
基金The authors would like to thank the finical support from Scientific Research Projects of Jilin Provincial Department of Education(Grant No.JJKH20200104KJ)National Natural Science Foundation of China(Grant No.51975392).
文摘Feedrate scheduling in computer numerical control(CNC)machining is of great importance to fully develop the capabilities of machine tools while maintaining the motion stability of each actuator.Smooth and time-optimal feedrate scheduling plays a critical role in improving the machining efficiency and precision of complex surfaces considering the irregular curvature characteristics of tool paths and the limited drive capacities of machine tools.This study develops a general feedrate scheduling method for non-uniform rational B-splines(NURBS)tool paths in CNC machining aiming at minimizing the total machining time without sacrificing the smoothness of feed motion.The feedrate profile is represented by a B-spline curve to flexibly adapt to the frequent acceleration and deceleration requirements of machining along complex tool paths.The time-optimal B-spline feedrate is produced by continuously increasing the control points sequentially from zero positions in the bidirectional scanning and sampling processes.The required number of knots for the time-optimal B-spline feedrate can be determined using a progressive knot insertion method.To improve the computational efficiency,the B-spline feedrate profile is divided into a series of independent segments and the computation in each segment can be performed concurrently.The proposed feedrate scheduling method is capable of dealing with not only the geometry constraints but also high-order drive constraints for any complex tool path with little computational overhead.Simulations and machining experiments are conducted to verify the effectiveness and superiorities of the proposed method.
基金supported by the Key Project of the National Natural Science Foundation of China(10932003,11272075)the National Basic Research Program of China(2010CB832700)"04"Great Project of Ministry of Industrialization and Information of China(2011ZX04001-21)
文摘The problem of quick analysis using exact geometry data was proposed by Hughes et al. and the isogeometric analysis framework was introduced as a solution. In this letter, the exact geometry concept is combined into the quasi-conforming framework and a novel method, i.e., the exact geometry based quasi-conforming analysis is proposed. In present method the geometry is exactly described by non-uniform rational B-spline bases, while the solution space by traditional polynomial bases. Present method combines the merits of both isogeometric analysis and quasi-conforming finite element method. In this letter Euler-Bernoulli beam problem is solved as an example and the results show that the present method is effective and promising.
文摘This paper presents an automatic programming system on PC, it has also solved the technic problem in the combination of different curves or surfaces. The NURBS is applied to modeling and fitting complicated curves and surfaces. The circular spline is combined with the NURBS to determine the cutter path in accordance with the features of the interpolation movement of NC machine tool. Three methods have been developed to solve the overcutting problems.
基金supported by the National Natural SciencFoundation of China (Grant No. 10572094)the NaturScience Foundation of Shanghai (Grant No. 06ZR14050)
文摘A desingularized high order panel method based on Non-Uniform Rational B-Spline (NURBS) was developed to deal with three-dimensional potential flow problems. A NURBS surface was used to precisely represent the body geometry. Velocity potential on the body surface was described by the B-spline after the source density distribution on the body surface had been solved. The collocation approach was employed to satisfy the Neurnann boundary condition and Gaussian quadrature points were chosen as both the collocation points and the source points. The singularity was removed by a combined method, so the process of the numerical computation was non-singular. In order to verify the method proposed, the unbounded flow problems of sphere and ellipsoid, the wave-making problem of a submerged ellipsoid were chosen as computational examples. It is shown that the numerical results are in good agreement with analytical solutions and other numerical results in all cases, and sufficient accuracy of numerical solution can be reached with a small number of panels.
基金the National Natural Science Foundation of China(Nos.51179019 and 51309152)
文摘A three-dimensional high-order panel method based on non-uniform rational B-spline(NURBS) is developed for predicting the hydrodynamic interaction forces on a moored ship induced by a passing ship in shallow water. An NURBS surface is used to precisely represent the hull geometry. Velocity potential on the hull surface is described by B-spline after the source density distribution on the boundary surface is determined. A collocation approach is applied to the boundary integral equation discretization. Under the assumption of low passing speed, the effect of free surface elevation is neglected in the numerical calculation, and infinite image method is used to deal with the finite water depth effect. The time stepping method is used to solve the velocity potential at each time step. Detailed convergence study with respect to time step, panel size and Green function is undertaken. The present results of hydrodynamic forces are compared with those obtained by slender-body theory to show the validity of the proposed numerical method. Calculations are conducted for different water depths and lateral distances between ships, and the detail results are presented to demonstrate the effects of these factors.
文摘This paper describes a method for mesh adaptation in the presence of intersections, such as wing-fuselage. Automatic optimization tools, using Computational Fluid Dynamics(CFD) simulations, face the problem to adapt the computational grid upon deformations of the boundary surface. When mesh regeneration is not feasible, due to the high cost to build up the computational grid, mesh deformation techniques are considered a cheap approach to adapt the mesh to changes on the geometry. Mesh adaptation is a well-known subject in the literature; however, there is very little work which deals with moving intersections. Without a proper treatment of the intersections,the use of automatic optimization methods for aircraft design is limited to individual components.The proposed method takes advantage of the CAD description, which usually comes in the form of Non-Uniform Rational B-Splines(NURBS) patches. This paper describes an algorithm to recalculate the intersection line between two parametric surfaces. Then, the surface mesh is adapted to the moving intersection in parametric coordinates. Finally, the deformation is propagated through the volumetric mesh. The proposed method is tested with the DLR F6 wing-body configuration.