In continuous casting production,droplet characteristics are important parameters for evaluating the nozzle atomization quality,and have a significant impact on the secondary cooling effect and the slab quality.In ord...In continuous casting production,droplet characteristics are important parameters for evaluating the nozzle atomization quality,and have a significant impact on the secondary cooling effect and the slab quality.In order to study the behavior of atomized droplets after reaching the slab surface and to optimize the spray cooling effect,the influence of droplet diameter and droplet velocity on the migration behavior of droplets in the secondary cooling zone was analyzed by FLUENT software.Results show that the droplets in the spray zone and on the slab surface are mainly concentrated in the center,thus,the liquid volume fraction in the center is higher than that of either side.As the droplet diameter increases,the region of high liquid volume fraction on the slab surface becomes wider,and the liquid phase distribution in the slab width direction becomes uneven.Although increasing the droplet velocity at the nozzle exit has little effect on droplet diffusion in the spray zone,the distribution becomes more uneven due to more liquid reaches the slab surface per unit time.A prediction formula of the maximum water flow rate on the slab surface for specific droplet characteristics was proposed based on dimensionless analysis and validated by simulated data.A nozzle spacing of 210 mm was recommended under the working conditions in this study,which ensures effective coverage of the spray water over the slab surface and enhances the distribution uniformity of water flow rate in the transverse direction.展开更多
A three-dimensional, non-isothermal, two-phase model for a PEM water electrolysis cell(PEMEC) is established in this study.An effective connection between two-phase transport and performance in the PEMECs is built thr...A three-dimensional, non-isothermal, two-phase model for a PEM water electrolysis cell(PEMEC) is established in this study.An effective connection between two-phase transport and performance in the PEMECs is built through coupling the liquid water saturation and temperature in the charge conservation equation. The distributions of liquid water and temperature with different operating(voltage, temperature, inlet velocity) and physical(contact angle, and porosity of anode gas diffusion layer) parameters are examined and discussed in detail. The results show that the water and temperature distributions, which are affected by the operating and physical parameters, have a combined effect on the cell performance. The effects of various parameters on the PEMEC are of interaction and restricted mutually. As the voltage increases, the priority factor caused by the change of inlet water velocity changes from the liquid water saturation increase to the temperature drop in the anode catalyst layer. While the priority influence factor caused by the contact angle and porosity of anode gas diffusion layer is the liquid water saturation. Decreasing the contact angle or/and increasing the porosity can improve the PEMEC performance especially at the high voltage. The results can provide a better understanding of the effect of heat and mass transfer and the foundation for optimization design.展开更多
基金funded by the National Natural Science Foundation of China(Nos.51974213 and 52174324)。
文摘In continuous casting production,droplet characteristics are important parameters for evaluating the nozzle atomization quality,and have a significant impact on the secondary cooling effect and the slab quality.In order to study the behavior of atomized droplets after reaching the slab surface and to optimize the spray cooling effect,the influence of droplet diameter and droplet velocity on the migration behavior of droplets in the secondary cooling zone was analyzed by FLUENT software.Results show that the droplets in the spray zone and on the slab surface are mainly concentrated in the center,thus,the liquid volume fraction in the center is higher than that of either side.As the droplet diameter increases,the region of high liquid volume fraction on the slab surface becomes wider,and the liquid phase distribution in the slab width direction becomes uneven.Although increasing the droplet velocity at the nozzle exit has little effect on droplet diffusion in the spray zone,the distribution becomes more uneven due to more liquid reaches the slab surface per unit time.A prediction formula of the maximum water flow rate on the slab surface for specific droplet characteristics was proposed based on dimensionless analysis and validated by simulated data.A nozzle spacing of 210 mm was recommended under the working conditions in this study,which ensures effective coverage of the spray water over the slab surface and enhances the distribution uniformity of water flow rate in the transverse direction.
基金supported by the National Natural Science Foundation of China (Grant Nos. 51876061 and 51821004)the Fundamental Research Funds for the Central Universities (Grant No. 2018ZD04)。
文摘A three-dimensional, non-isothermal, two-phase model for a PEM water electrolysis cell(PEMEC) is established in this study.An effective connection between two-phase transport and performance in the PEMECs is built through coupling the liquid water saturation and temperature in the charge conservation equation. The distributions of liquid water and temperature with different operating(voltage, temperature, inlet velocity) and physical(contact angle, and porosity of anode gas diffusion layer) parameters are examined and discussed in detail. The results show that the water and temperature distributions, which are affected by the operating and physical parameters, have a combined effect on the cell performance. The effects of various parameters on the PEMEC are of interaction and restricted mutually. As the voltage increases, the priority factor caused by the change of inlet water velocity changes from the liquid water saturation increase to the temperature drop in the anode catalyst layer. While the priority influence factor caused by the contact angle and porosity of anode gas diffusion layer is the liquid water saturation. Decreasing the contact angle or/and increasing the porosity can improve the PEMEC performance especially at the high voltage. The results can provide a better understanding of the effect of heat and mass transfer and the foundation for optimization design.
