Corrective Effect of the Angle of Incidence of the Magnetic Field Intensity on the Performance (Series and Shunt Resistances) of a Bifacial Silicon Solar Cell

This article presents a three-dimensional analysis of the impact of the angle of incidence of the magnetic field intensity on the electrical performance (series resistance, shunt resistance) of a bifacial polycrystalline silicon solar cell. The cell is illuminated simultaneously from both sides. The continuity equation for the excess minority carriers is solved at the emitter and at the depth of the base respectively. The analytical expressions for photocurrent density, photovoltage, series resistance and shunt resistance were deduced. Using these expressions, the values of the series and shunt resistances were extracted for different values of the angle of incidence of the magnetic field intensity. The study shows that as the angle of incidence increases, the slopes of the minority carrier density for the two modes of operation of the solar cell decrease. This is explained by a drop in the accumulation of carriers in the area close to the junction due to the fact that the Lorentz force is unable to drive the carriers towards the lateral surfaces due to the weak action of the magnetic field, which tends to cancel out as the incidence angle increases, and consequently a drop in the open circuit photovoltage. This, in turn, reduces the Lorentz force. These results predict that the p-n junction of the solar cell will not heat up. The study also showed a decrease in series resistance as the incidence angle of the magnetic field intensity increased from 0 rad to π/2 rad and an increase in shunt resistance as the incidence angle increased. His behaviour of the electrical parameters when the angle of incidence of the field from 0 rad to π/2 rad shows that the decreasing magnetic field vector tends to be collinear with the electron trajectory. This allows them to cross the junction and participate in the external current. The best orientation for the Lorentz force is zero, in which case the carriers can move easily towards the junction.

Elliptically polarized high-order harmonic generation of Ar atom in an intense laser field

High-order harmonic generation(HHG) of Ar atom in an elliptically polarized intense laser field is experimentally investigated in this work.Interestingly,the anomalous ellipticity dependence on the laser ellipticity(ε) in the lower-order harmonics is observed,specifically in the 13rd-order,which displays a maximal harmonic intensity at ε ≈ 0.1,rather than at ε = 0 as expected.This contradicts the general trend of harmonic yield,which typically decreases with the increase of laser ellipticity.In this study,we attribute this phenomenon to the disruption of the symmetry of the wave function by the Coulomb effect,leading to the generation of a harmonic with high ellipticity.This finding provides valuable insights into the behavior of elliptically polarized harmonics and opens up a potential way for exploring new applications in ultrafast spectroscopy and light–matter interactions.

Modulation of the Wind Field Structure of Initial Vortex on the Relationship between Tropical Cyclone Size and Intensity

This study investigates the modulation of initial wind field structure on the relationship between the size and intensity of a simulated vortex.A series of idealized experiments are conducted by varying the radius of maximum wind(RMW)and shape parameter of the initial vortices.The size–intensity relationship is quantified by the linear regression coefficient of the azimuthally-averaged gale-force wind radius against the maximum wind during the development stage,reflecting the degree of size expansion at the same intensity increment.The regression coefficient increases with increased RMW and decreased,with the RMW being the primary constraint.The effect of lowering on the elevation of the regression coefficient gradually stands out when the initial RMW is large.Enlarging the RMW leads to a secondary circulation with a horizontally elongated structure,which retards the intensification while promoting size expansion,thus substantially enhancing size expansion as the vortex intensifies.Broadening the wind field outside the RMW by reducing results in abounding convection in the outer region,which promotes size expansion.Based on the axisymmetric tangential wind tendency and Sawyer–Eliassen equations,when the RMW is large,the active convection in the outer region can weaken the radial inflow induced by the eyewall heating in the inner region,thus retarding the intensification by reducing the radial imports of vorticity near the RMW.

Mechanism and Kinetic Model of In-situ TiB_2/7055Al Nanocomposites Synthesized under High Intensity Ultrasonic Field

In-situ TiB2/7055Al nanocomposites are fabricated by in situ melt chemical reaction from 7055Al-K2TiF6-KBF4 system under high intensity ultrasonic field,and the mechanism and kinetic model of in-situ melt chemical reaction are investigated.X-ray diffraction （XRD） and scanning electron microscope （SEM） analyses indicate that the sizes of in-situ TiB2 nanoparticles are in the range of 80-120 nm.The results of ice-water quenched samples show that the whole process contains four stages,and the overall in-situ reaction time is 10 minutes.The in situ synthesis process is controlled mainly by chemical reaction in earlier stage （former 3 minutes）,and by the particulate diffusing in later stage.The mechanism of key reaction between Al3Ti and AlB2 under high intensity ultrasonic in the 7055Al-K2TiF6-KBF4 system is the reaction-diffusion-crack-rediffusion.Furthermore,the reactive kinetic models in 7055Al-K2TiF6-KBF4 system are established.

Field survey around strong motion stations and its implications on the seismic intensity in the Lushan earthquake on April 20,2013

The Ms7.0 Lushan earthquake on April 20, 2013 is another destructive event in China since the Ms8.0 Wenchuan earthquake in 2008 and Ms7.1 Yushu earth- quake in 2010. A large number of strong motion recordings were accumulated by the National Strong Motion Obser- vation Network System of China. The maximum peak ground acceleration （PGA） at Station 51BXD in Baoxing Country is recorded as -1,005.3 cm/s2, which is even larger than the maximum one in the Wenchuan earthquake. A field survey around three typical strong motion stations confirms that the earthquake damage is consistent with the issued map of macroseismic intensity. For the oscillation period 0.3-1.0 s which is the common natural period range of the Chinese civil building, a comparison shows that the observed response spectrums are considerably smaller than the designed values in the Chinese code and this could be one of the reasons that the macroseismic intensity is lower than what we expected despite the high amplitude of PGAs. The Housner spectral intensities from 16 stations are also basically correlated with their macroseismic intensities, and the empirical distribution of spectral intensities from Lushan and Wenchuan Earthquakes under the Chinese scale is almost identical with those under the European scale.

Distribution characteristics of intensity and phase vortices of speckle fields produced by N-pinhole random screens

We analyze the distribution properties of phase and phase vortices in a speckle field generated by N-pinhole random screens, and find that the phase vortex distributions show similarity and clustering in local regions. The phase patterns have a lot of sets composed of two phase vortices with opposite signs or four phase vortices which are positive and negative vortices alternately. Cases are also found where two adjacent phase vortices have the same topological charges. The density of phase vortices becomes larger with the increase of the radius of circumference and the number of pinholes on screen.Then, the relative positions of phase vortices can be adjusted by changing the radius of circumference and the number of pinholes.

Research on Simulation Methods of Electric Field Intensity on Surface of 10 kV Cable Joint

The electric field intensity (EFI) is important characteristic quantity for evaluating the internal insulation state of cable joints. Based on finite element method, this paper proposes two EFI research methods, field-circuit coupling method and equivalent circuit method. The average EFI of the inner surface of the outer semi-conducting shield can be calculated from the current in the measuring circuit. The relative error between these two methods is about 15%, which roughly proves the consistency of the two methods. Further practical application research enables online monitoring of cable joints.

Consistency of the directionality of partially coherent beams in turbulence expressed in terms of the angular spread and the far-field average intensity

Under the quadratic approximation of the Rytov＇s phase structure function, this paper derives the general closed-form expressions for the mean-squared width and the angular spread of partially coherent beams in turbulence. It finds that under a certain condition different types of partially coherent beams may have the same directionality as a fully coherent Gaussian beam in free space and also in atmospheric turbulence if the angular spread is chosen as the characteristic parameter of beam directionality. On the other hand, it shows that generally, the directionality of partially coherent beams expressed in terms of the angular spread is not consistent with that in terms of the normalized far-field average intensity distribution in free space, but the consistency can be achieved due to turbulence.

The Effects of High-intensity Pulsed Electromagnetic Field on Proliferation and Differentiation of Neural Stem Cells of Neonatal Rats in vitro

The effects of high-intensity pulsed electromagnetic stimulation （HIPEMS） on proliferation and differentiation of neonatal rat neural stem cells in vitro were investigated. Neural stem cells derived from neonatal rats were exposed to 0.1 Hz, 0.5–10 Tesla （T） [8 groups of B–I, respectively], 5 stimuli of HIPEMF. The sham exposure controls were correspondingly established. Inverted phase contrast microscope was used to observe the cultured cells, MTT assay to detect the viability of the cells as expressed by absorbance （A） value, and flow cytometry to measure differentiation of neural stem cells. The results showed that A values of neural stem cells in both 3.0 T and 4.0 T groups were significantly higher than the other groups 24 to 168 h post HPEMS, indicating a strong promotion of the growth of neural stem cells （P〈0.05）. The A values of neural stem cells in the 6.0 T, 8.0 T, and 10.0 T groups were lower than the sham exposure control group, indicating a restraint of the growth of neural stem cells. The rate of neuron-specific enolase-positive neurons revealed by flow cytometry in HPEMS groups was the same as that in control group （P〉0.05）. It was suggested that 0.1 Hz, 5 pulses stimulation of HPEMS within certain scale of intensity （0.5–10.0 T）, significantly promoted the growth of neural stem cells with the rational intensity being 4.0 T.

Internal electric field modulation by copper vacancy concentration of cuprous sulfide nanosheets for enhanced selective CO_(2) photoreduction

Although the internal electric field(IEF)of photocatalysts is acknowledged as a potent driving force for photocharge separation,modulating the IEF intensity to achieve enhanced photocatalytic performances remains a challenge.Herein,cuprous sulfide nanosheets with different Cu vacancy concentration were employed to study IEF modulation and corresponding direct charge transfer.Among the samples,Cu_(1.8)S nanosheets possessed intensified IEF intensity compared with those of Cu_(2)S and Cu_(1.95)S nanosheets,suggesting that an enhanced IEF intensity could be achieved by introducing more Cu vacancies.This intensified IEF of Cu_(1.8)S nanosheets induced numerous photogenerated electrons to migrate to its surface,and the dissociative electrons were then captured by Cu vacancies,resulting in efficient charge separation spatially.In addition,the Cu vacancies on Cu_(1.8)S nanosheets accumulated electrons as active sites to lower the energy barrier of rate-determining step of CO_(2)photoreduction,leading to the selective conversion of CO_(2)to CO.Herein,the manipulation of IEF intensity through Cu vacancy concentration regulation of cuprous sulfide photocatalysts for efficient charge separation has been discussed,providing a scientific strategy to rationally improve photocata lytic performances for solar energy conversion.

Effect of Electric Field Intensity on the Morphology of Magnetic-field-assisted Electrospinning PVP Nanofibers

Polyvinylpyrrolidone （PVP） nanofibers were processed by magnetic-field-assisted electrospinning （MFAES） technique. Since electric field intensity was one of the most important parameters influencing fiber morphology, the research aimed to study how electric field intensity affects fiber morphology in MFAES technique. The experimental results revealed that the distribution of diameter widened while the average diameter of PVP fibers decreased and the degree of the alignment reduced with the increase of electric field intensity. However, the fibers would be conglutinated together when the electric field intensity was too low. Also, the increase of working distance made the average diameter and the degree of the alignment increase slightly under the same electric field intensity, but the fibers could be partially curved instead of being fully straight if the working distance was too long. It was also indicated that maintaining the electric field intensity at 1 kV/cm With the voltage-distance combinations of 12 kV-12 cm （for 12wt% PVP） and 15 kV-15 cm （for 14wt% PVP） among all other combinations would result in the optimal alignment as well as a narrow size distribution of the fibers.

The Impact of Small Field’s Off-Set on Output Factor in Intensity Modulated Radiation Treatment

In intensity modulated radiation treatment (IMRT) planning, the use of asymmetrically collimated fields that are placed on central axis or its off-set is mostly required. Output is the main topic discussed today for extremely small and/or severe irregularly shaped fields. The air scatter data are involved directly or indirectly in obtaining the output. Despite the fact that extensive data have been published in many studies to provide a guide on the magnitude of output factor for clinical accelerators, there are very few data reviewed about output factor in-air or phantom for off-set fields. This study was aimed to investigate the impact of these conditions for small fields. This study was conducted in Elekta Synergy linear accelerator which produces 6 MV X-ray energy. The in-air output factor (Sc) has been measured by CC04 ion chamber with brass-alloy “build-up” cap and Dose-1 electrometer, and the total output (Scp) measurements were carried on at dose maximum depth in phantom by the same chamber and Thermoluminescence dosimeter (TLD) for 1 - 10 cm2 fields. The all measurements at center of isocenter and off-set fields at three directions (X2, Y1, Diagonal) were done. By decreasing field size from 10 to 2 cm2 at isocenter, the Sc value using CC04 was decreased to 5.4% and Scp using CC04 and TLD to 14.5% and 11% respectively. By increasing off-set value, the Sc and Scp values were increased in all directions comparing to central fields. The maximum increase was obtained in Y1 direction for Sc and Scp. TLD results for Scp is slightly higher than CC04. The dosimetric properties of small fields and their off-set should be evaluated and modelled appropriately in the treatment planning system to ensure accurate dose calculation in Intensity Modulated Radiation Treatment.

Analysis of the stress intensity factor of welded joints under prior corrosion and complex stress fields

Taking cruciform welded joints under different corrosion degrees, together with 45° inclined angle and full penetration load-carrying fillet, as the research object, the stress intensity factor of a quarter-circular comer crack of welded joints is calculated based on FRANC3D with ABAQUS. Effects of different corrosion pit sizes, crack aspect ratios, and crack depths on stress intensity factor are analyzed. The results show that pit depth plays a major role in stress intensity factor, while the effect of pit radius is relatively small. The cracking modes of the surface and the deepest point are mode I, and mixed modes I and II, respectively. Effects of pit depths, crack aspect ratios, and crack depths on the stress intensity factor at the surface point are greater than at the deepest point.

The 2018 M_S 5.9 Mojiang Earthquake:Source model and intensity based on near-field seismic recordings

On September 8, 2018, an M_S 5.9 earthquake struck Mojiang, a county in Yunnan Province, China. We collect near-field seismic recordings(epicentral distances less than 200 km) to relocate the mainshock and the aftershocks within the first 60 hours to determine the focal mechanism solutions of the mainshock and some of the aftershocks and to invert for the finite-fault model of the mainshock.The focal mechanism solution of the mainshock and the relocation results of the aftershocks constrain the mainshock on a nearly vertical fault plane striking northeast and dipping to the southeast. The inversion of the finite-fault model reveals only a single slip asperity on the fault plane. The major slip is distributed above the initiation point, ～14 km wide along the down-dip direction and ～14 km long along the strike direction, with a maximal slip of ～22 cm at a depth of ～6 km. The focal mechanism solutions of the aftershocks show that most of the aftershocks are of the strike-slip type, a number of them are of the normal-slip type, and only a few of them are of the thrust-slip type.On average, strike-slip is dominant on the fault plane of the mainshock, as the focal mechanism solution of the mainshock suggests, but when examined in detail, slight thrust-slip appears on the southwest of the fault plane while an obvious part of normal-slip appears on the northeast, which is consistent with what the focal mechanism solutions of the aftershocks display. The multiple types of aftershock focal mechanism solutions and the slip details of the mainshock both suggest a complex tectonic setting, stress setting, or both. The intensity contours predicted exhibit a longer axis trending from northeast to southwest and a maximal intensity of Ⅷ around the epicenter and in the northwest.

Features of Recombination Radiation of GaAs Type Semiconductors with the Participation of Fine Acceptor Levels in a Magnetic Field

Using the method of Picus and Beer invariants, general expressions are obtained for the total intensity I and the degree of circular polarization Рcirc.of the luminescence of GaAs-type semiconductors with the participation of shallow acceptor levels in a longitudinal magnetic field H. Special cases are analyzed depending on the value and direction of the magnetic field strength, as well as on the constants of the g-factor of the acceptor g1,g2and the conduction band electron ge. In the case of a strong magnetic field H// [100], [111], [110], a numerical calculation of the angular dependence of the quantities I and Рcirc.was performed for some critical values of g2/g1, at which Рcirc.exhibits a sharp anisotropy in the range from −100% to +100%, and the intensity of the crystal radiation along the magnetic field tends to a minimum value.

Numerical Study on the Two-Dimensional Temperature Fields of Titanium/Aluminum Double-Layer Target Irradiated by High-Intensity Pulsed Ion Beam

Interaction between high-intensity pulsed ion beam （HIPIB） and a double-layer target with titanium film on top of aluminum substrate was simulated. The two-dimensional nonlinear thermal conduction equations, with the deposited energy in the target taken as source term, were derived and solved by finite differential method. As a result, the two-dimensional spatial and temporal evolution profiles of temperature were obtained for a titanium/aluminum double-layer target irradiated by a pulse of HIPIB. The effects of ion beam current density on the phase state of the target materials near the film and substrate interface were analyzed. Both titanium and aluminum were melted near the interface after a shot when the ion beam current density fell in the range of 100 A/cm2 to 200 A/cm2.

Dose Comparison between Eclipse Dose Calculation and Fast Dose Calculator in Single- and Multi-Field Optimization Intensity-Modulated Proton Therapy Plans with Various Multi-Beams for Brain Cancer

The purpose of this study was to grasp current potential problems of dose error in intensity-modulated proton therapy (IMPT) plans. We were interested in dose differences of the Varian Eclipse treatment planning system (TPS) and the fast dose calculation method (FDC) for single-field optimization (SFO) and multi-field optimization (MFO) IMPT plans. In addition, because some authors have reported dosimetric benefit of a proton arc therapy with ultimate multi-fields in recent years, we wanted to evaluate how the number of fields and beam angles affect the differences for IMPT plans. Therefore, for one brain cancer patient with a large heterogeneity, SFO and MFO IMPT plans with various multi-angle beams were planned by the TPS. Dose distributions for each IMPT plan were calculated by both the TPS’s conventional pencil beam algorithm and the FDC. The dosimetric parameters were compared between the two algorithms. The TPS overestimated 400 - 500 cGy (RBE) for minimum dose to the CTV relative to the dose calculated by the FDC. These differences indicate clinically relevant effect on clinical results. In addition, we observed that the maximum difference in dose calculated between the TPS and the FDC was about 900 cGy (RBE) for the right optic nerve, and this quantity also has a possibility to have a clinical effect. The major difference was not seen in calculations for SFO IMPT planning and those for MFO IMPT planning. Differences between the TPS and the FDC in SFO and MFO IMPT plans depend strongly on beam arrangement and the presence of a heterogeneous body. We advocate use of a Monte Carlo method in proton treatment planning to deliver the most precise proton dose in IMPT.

Theoretical study of the influence of intense femtosecond laser field on the evolution of the wave packet and the population of NaRb molecule

Employing the two-state model and the time-dependent wave packet method, we have investigated the influences of the parameters of the intense femtosecond laser field on the evolution of the wave packet, as well as the population of ground and double-minimum electronic states of the NaRb molecule. For the different laser wavelengths, the evolution of the wave packet of 6{ }^1／Sigma ^ ＋ state with time and internuclear distance is different, and the different laser intensity brings different influences on the population of the electronic states of the NaRb molecule. One can control the evolutions of wave packet and the population in each state by varying the laser parameters appropriately, which will be a benefit for the light manipulation of atomic and molecular processes.

The dissociation pathways of N_2^+ in intense femtosecond laser fields

Using a neutral N2 beam as target, this paper studies the dissociation of N2^＋ in intense femtosecond laser fields （45 fs, ～ 1 × 10^16 W/cm^2） at the laser wavelength of 800 nm based on the time-of-flight mass spectra of N＋ fragment ions. The angular distributions of N^＋ and the laser power dependence of N^＋ yielded from different dissociation pathways show that the dissociation mechanisms mainly proceed through the couplings between the metastable states （A, B and C） and the upper excited states of N^＋.A coupling model of light-dressed potential energy curves of N2^＋ is used to interpret the kinetic energy release of N^＋.

Observation of the optical X2Σg+–A2Πu coupling in N2+ lasing induced by intense laser field

We propose a simple pump-coupling-seed scheme to examine the optical X^2Σg^+–A^2Πu coupling in N2^+ lasing. We produce the N2^+ lasing at 391 nm, corresponding to the B^2Σu^+(v = 0)–X^2Σg+(v = 0) transition, by externally seeding the N^2+ gain medium prepared by irradiation of N2 with an intense pump pulse. We then adopt a weak coupling pulse in between the pump and seed pulses, and show that the intensity of the 391-nm lasing can be efficiently modulated by varying the polarization direction of the coupling pulse with respect to that of the pump pulse. It is found that when the polarization directions of the pump and coupling pulses are perpendicular, the 391-nm lasing intensity is more sensitive to the coupling laser energy, which reflects the inherent nature of the perpendicular X^2+Σg^–A^2Πu transition.