Evaluation of the Shear Strength of Perfobond Rib Connectors in Ultra High Performance Concrete

Since the previous strength prediction models for the perfobond rib connector were proposed based upon the results of push-out tests conducted on concretes with compressive strength below 50 MPa, push-out test is performed on perfobond shear connectors applying ultra high performance concretes with compressive strength higher than 80 MPa to evaluate their shear resistance. The test variables are chosen to be the diameter and number of dowel holes and, the change in the shear strength of the perfobond rib connector is examined with respect to the strength of two types of UHPC: steel fiber-reinforced concrete with compressive strength of 180 MPa and concrete without steel fiber with compressive strength of 80 MPa. The test results reveal that higher concrete strength and larger number of holes increased the shear strength, and that higher increase rate in the shear strength was achieved by the dowel action. The comparison with the predictions obtained by the previous models shows that the experimental results are close to the values given by the model proposed by Oguejiofor and Hosain [1].

Seismic Performance of High-Strength Short Concrete Column with High-Strength Stirrups Constraints

The seismic performance of four short concrete columns was investigated under low cycle and repeated loads, including the failure characteristics, hysteretic behavior, rigidity degeneracy and steel-bar stress. The influences of reinforcement strength, stirrup ratio and shear span ratio were also compared. Test results reveal that the restriction effect of stirrups can improve the peak stress, so the bearing capacity of specimen can be improved; for the high-strength short concrete column with high-strength stirrups, it was more reasonable to use ultimate displacement angle to reflect the ductility of the specimen, and the yield strength of high-strength stirrups should be devalued when calculating the stirrup characteristic value; the seismic performance of short column would be improved with the increase of volume–stirrup ratio and shear span ratio; the high-strength stirrups and high-strength longitudinal reinforcements did not yield when the load acting on the specimen reached the peak value, which brought adequate safety stock to these short columns. © 2017, Tianjin University and Springer-Verlag Berlin Heidelberg.

A Study on the Bond Strength between High Performance Concrete and Reinforcing Bar

As a preliminary study for the erection of floating structures using high performance concrete, this paper examines the bond characteristics between concrete and the reinforcing bar. Since the floating structure is constructed in aquatic environment, corrosion of the reinforcing steel is likely to develop more prematurely than in onshore structure in case of concrete cracking. A solution to this corrosion problem could use FRP rebar instead of steel reinforcement. To that goal, an experimental study is conducted on the concrete-FRP bond strength to verify if such FRP rebar develops performance comparable to the conventional steel rebar. A series of tests are performed considering the bond length of ordinary steel rebar and G-FRP rebar as test variable with respect to the strength of concrete, and the results are presented.

STUDY ON OPTIMIZATION OF HIGH PERFORMANCE CONCRETE ADMIXTURES

Influences of admixtures on the workability and strength of high performance concrete （HPC） are in- vestigated. The types of investigated admixtures include naphthalene series high range water reducing agent, polycarboxlic series high range water reduce agent and sodium sulfate hardening accelerating agent. Two kinds of curing condition, namely steam curing condition and standard curing condition, are adopted. The result shows that HPC, added with polycarboxlic series of high performance water reducer, has high workability and strength, while sodium sulfate accelerating agent causes poor workability and low strength. Thus for vapor-cured HPC and its formulations, naphthalene series high range water reducing agent with less sodium sulfate should be given pri- ority. Therefore, the differences of curing conditions should be considered when selecting HPC admixtures.

FAILURE MODE AND CONSTITUTIVE MODEL OF PLAIN HIGH-STRENGTH HIGH-PERFORMANCE CONCRETE UNDER BIAXIAL COMPRESSION AFTER EXPOSURE TO HIGH TEMPERATURES

An orthotropic constitutive relationship with temperature parameters for plain highstrength high-performance concrete （HSHPC） under biaxial compression is developed. It is based on the experiments performed for characterizing the strength and deformation behavior at two strength levels of HSHPC at 7 different stress ratios including a=σs ： σ3=0.00：-1,-0.20：-1,-0.30 ： -1,-0.40：-1,-0.50：-1,-0.75：-1,-1.00：-1, after the exposure to normal and high temperatures of 20, 200, 300, 400, 500 and 600℃, and using a large static-dynamic true triaxial machine. The biaxial tests were performed on 100 mm×100 mm×100 mm cubic specimens, and friction-reducing pads were used consisting of three layers of plastic membrane with glycerine in-between for the compressive loading plane. Based on the experimental results, failure modes of HSHPC specimens were described. The principal static compressive strengths, strains at the peak stress and stress-strain curves were measured; and the influence of the temperature and stress ratios on them was also analyzed. The experimental results showed that the uniaxial compressive strength of plain HSHPC after exposure to high temperatures does not decrease dramatically with the increase of temperature. The ratio of the biaxial to its uniaxial compressive strength depends on the stress ratios and brittleness-stiffness of HSHPC after exposure to different temperature levels. Comparison of the stress-strain results obtained from the theoretical model and the experimental data indicates good agreement.

Strength Regularity and Failure Criterion of High-Strength High-Performance Concrete under Multiaxial Compression

Multiaxial compression tests were performed on 100 mm×100 mm×100 mm high-strength high-performance concrete （HSI-IPC） cubes and normal strength concrete （NSC） cubes. The failure modes of specimens were presented, the static compressive strengths in principal directions were measured, the influence of the stress ratios was analyzed. The experimental results show that the ultimate strengths for HSHPC and NSC under multiaxial compression are greater than the uniaxial compressive strengths at all stress ratios, and the multiaxial strength is dependent on the brittleness and stiffness of concrete, the stress state and the stress ratios. In addition, the Kupfer-Gersfle and Ottosen＇s failure criteria for plain HSHPC and NSC under multiaxial compressive loading were modified.

Seismic Performance of Steel Reinforced Ultra High-strength Concrete Columns

The seismic performance of steel reinforced ultra-high-strength concrete columns(SRSHC) with various shear-span ratios(λ) were studied through a series of experiments.The concrete compressive cube strength value of experimental specimens ranged from 92.9 MPa to 108.1 MPa.The main experimental variables affecting seismic performance of specimens were axial load ratio and stirrup reinforcement ratio.The columns(λ=2.75) subjected to low cyclic reversed lateral loads failed mainly in the flexural-shear mode failure and columns(λ≤2.0) subjected to low cyclic reversed lateral loads failed mainly in the shear mode failure.Shear force-displacement hysteretic curves and skeleton curves were drawn.Coefficient of the specimen displacement ductility was calculated.Experimental results indicate that ductility decreases with axial pressure ratio increasing,and increases with stirrup reinforcement ratio increasing.Limit values of axial pressure ratio and minimum stirrup reinforcement ratio of columns are proposed to satisfy definite ductility requirement.The suggested values provide a reference for engineering application and for the amendment of the current Chinese design code of steel reinforced concrete composite structures.

Characterization of Surface Hardness and Microstructure of High Performance Concrete

The relationship between compressive strength obtained by universal testing machine and rebound value obtained by the hammer of high performance concrete was systematically investigated at the macro level. And a model of high performance concrete strength curve was established from them. At the micro level, the microstructure, hydration products and pore structure of concrete surface were analyzed by scanning electron microscopy（SEM）, comprehensive thermal analysis（TG-DSC） and mercury intrusion porosimetry（MIP）, respectively. The effect of carbonation on surface strength was also investigated. The results showed that the concrete surface hardness layer grew rapidly at early stage and then stabilized at last with ongoing curing age; the rebound value and compressive strength of concrete with slag were higher than those of concrete with the same content of fly ash. In addition, the strength curve obtained by the least square method can satisfy the local standard requirements with an average relative error of 8.9% and a relative standard deviation of 11.3%. When the carbonation depth was 6 mm, the compressive strength calculated by national uniform strength curve was 25 PMa higher than that by high performance concrete.

A Simple Mix Proportion Design Method Based on Frost Durability for Recycled High Performance Concrete Using Fully Coarse Recycled Aggregate

Durability design of recycled high performance concrete（RHPC） is fundamental for improving the use rate and level of concrete waste as coarse recycled aggregate（CRA）. We discussed a frostdurability-based mix proportion design method for RHPC using 100 % CRA and natural sand. Five groups of RHPC mixes with five strength grades（40, 50, 60, 70 and 80 MPa） were produced using CRA with four quality classes, and their workability, 28 d compressive strengths and frost resistances（measured by the compressive strength loss ratio and the relative dynamic modulus of elasticity） were tested. Relationships between the 28 d compressive strength, the frost resistance and the CRA quality characteristic parameter, water absorption, were then developed. The criterion of a CRA maximum water absorption limit value for RHPC was suggested, independent of its source and quality class. The results show that all RHPC mixes achieve the expected target workability, strength, and frost durability. The research results demonstrate that the application of the proposed method does not require trial testing prior to use.

Influence of shrinkage-reducing admixture on drying shrinkage and mechanical properties of high-performance concrete

High-performance concrete （HPC） has specific performance advantages over conventional concrete in strength and durability. HPC mixtures are usually produced with water/binder mass ratios （mW/mB） in the range of 0.2-0.4, so volume changes of concrete as a result of drying, chemical reactions, and temperature change cannot be avoided. For these reasons, shrinkage and cracking are frequent phenomena. It is necessary to add some types of admixture for reduction of shrinkage and cracking of HPC. This study used a shrinkage-reducing admixture （SRA） for that purpose. Concrete was prepared with two different mW/mB （0.22 and 0.40） and four different mass fractions of SRA to binder （w（SRA） = 0%, 1%, 2%, and 4%）. The mineral admixtures used for concrete mixes were： 25% fly ash （FA） and 25% slag by mass of binder for the mixture with mW/mB = 0.40, and 15% silica fume （SF） and 25% FA for the mixture with mW/mB = 0.22. Tests were conducted on 24 prismatic specimens, and shrinkage strains were measured through 120 days of drying. Compressive strength, splitting strength, and static modulus of elasticity were also determined. The results show that the SRA effectively reduces some mechanical properties of HPC. The reductions in compressive strength, splitting tensile strength, and elastic modulus of the concrete were 7%-24%, 9%-19%, and 5%-12%, respectively, after 90 days, compared to concrete mixtures without SRA. SRA can also help reduce drying shrinkage of concrete. The shrinkage strains of HPC with SRA were only as high as 41% of the average free shrinkage of concrete without SRA after 120 days of drying.

Design of Eco-friendly Ultra-high Performance Concrete with Supplementary Cementitious Materials and Coarse Aggregate

Aiming to investigate the mix design of eco-friendly UHPC with supplementary cementitious materials and coarser aggregates, we comprehensively studied the workability, microstructure, porosity, compressive strength, flexural strength, and Young’s modulus of UHPC. Relationship between compressive strength and Young’s modulus was obtained eventually. It is found that the compressive strength, flexural strength, and Young’s modulus of UHPC increase by 19.01%, 10.81%, and 5.99%, respectively, when 40 wt% cement is replaced with supplementary cementitious materials. The relationship between compressive strength and Young’s modulus of UHPC is an exponential form.

Spalling and Mechanical Properties of Fiber Reinforced High-performance Concrete Subjected to Fire

Spalling and mechanical properties of FRHPC subjected to fire were tested on notched beams. The results confirm that the internal vapor pressure is the leading reason for spalling of high-performance concrete （HPC）. At the same time, the temperature-increasing velocity and constrained conditions of concrete element also play significant roles in spalling. Steel fibers cannot reduce the risk of spalling, although they have obvious beneficial effects on the mechanical properties of concrete before and after exposure to fire. Polypropylene （PP） fibers are very useful in preventing HPC from spalling, however, they have negative effects on the strengths. By using hybrid fibers （steel fibers＋PP fibers）, both good anti-spalling performance and improved mechanical properties come true, which may provide necessary safe guarantee for the rescue work and structure repair after fire disaster.

Different Curing Systems on Mechanical Properties of Ultra-High Performance Concrete with Coarse Aggregate

High durability and high tensile strength makes ultra-high performance concrete( UHPC) an ideal material for bridges,while its early shrinkage in the construction of cast-in-situ mass concrete leads structure crack-easily,which restricts the application of UHPC in deck system. Whether reasonable amount of coarse aggregate can influence the strength of UHPC and improve the shrinkage performance or reduce the cost is still in doubt. Besides,in order to improve its constructability and workability, whether autoclaved curing system of UHPC can be changed remains to be further researched. In response to these circumstances, a systematic experimental study on the strength of UHPC mixed with coarse aggregate in different ratios has been presented in this paper. The three curing systems,namely standard curing,180-200 ℃/1. 1 MPa autoclaved curing,and hot water curing were tested to reveal the relationship between UHPC's properties and curing systems,and the UHPC ' s microstructure was also preliminarily studied by scanning electron microscope( SEM). The experimental research can draw the following conclusions. Under the condition of the same mix ratio, autoclaved curing guarantees the highest compressive strength,followed by hot water curing and standard curing. The compressive strength of concrete increases with the temperature in the range of 25 to 90 ℃ hot water curing,and high temperature in precuring period can speed up the strength development of UHPC,but the sequence of precuring period does not obviously affect the results. In 90 ℃ hot water and autoclaved curing,the strength is over 150 MPa,and it has little relation with gravel ratio. While the value increases first and then decreases in a lower temperature curing with the increasing of gravel amount,even only about 80 MPa at room temperature. The strength increases moderately along with the increase of the curing age by standard curing,especially in the initial stage.

Preparation for Retarding and High Early Strength Concrete

The primary objective of this research was to determine optimum dosage of mixing concrete containing plasticizers and fly ash, consistent with desirable structural grade concrete properties. Factorial tests were also conducted to investigate the four main factors： water-cementing materials ratio, water content, content of superplasticizers （SP） and fly ash content. It was found that the requirement for setting time played the dominant role in shrinkage and anti-cracking, and fly ash played a critical role in workability and reducing heat of hydration but showed insignificant effects on slump, early strength and initial setting time of concrete.

Seismic Behavior of Steel Reinforced Ultra High Strength Concrete Column and Reinforced Concrete Beam Connection

To investigate the seismic behavior of connections composed of steel reinforced ultra high strength concrete (SRUHSC) column and reinforced concrete (RC) beam, six interior strong-column-weak-beam connection specimens were tested subjected to reversal cyclic load. Effects of applied axial load ratio and volumetric stirrup ratio on ductility, energy dissipation capacity, strength degradation and rigidity degradation were discussed. It was found that all connection specimens failed in bending in a ductile manner with a beam plastic hinge. The ductility and energy dissipation capacity increased with the decrease of applied axial load ratio or increase of volumetric stirrup ratio. The displacement ductility coefficient and equivalent damping coefficient lay between those of steel reinforced ordinary concrete connection and those of reinforced concrete connection. The applied axial load ratio and volumetric stirrup ratio had less influence on the strength degradation and more influence on the stiffness degradation. The stiffness degraded sharply with the decrease of volumetric stirrup ratio or increase of applied axial load ratio. The experimental results indicate that SRUHSC column and RC beam connection exhibited better seismic performance and can provide reference for engineering application.

Shrinkage, Strength of High and Ordinary Concrete Incorporating Kosovo and Japanese Fly-ash

Ordinary and high performance concrete （OC-C 25/30 and HPC C-50/60） made with fly ash has found numerous applications all over the world since 1970. In Kosovo, fly ash as cement substitution in concrete has not been utilized yet despite the large amount that is produced annually and the positive economical-environment aspects of such technique. This hesitance is due to the laek of experience in the concrete engineering field and because of the chemical composition of Kosovo fly ash, which is classified as non-standard high calcium fly ash （KF）. In light of this fact, this study intended to develop further. So, this paper reports the consistency, workability, shrinkage, high and ordinary compressive strength of concrete containing different percentage of non-class high calcium fly ash as Portland cement substitution （first case-Kosovo fly ash KF） comparing results with F class-low caleium fly ash content （second ease-Japanese fly ash JF） which is common used as cement replacement.

Analysis of Compressive Strength Development of Ultra-high Performance Concrete

A numerical procedure was presented for evaluating the compressive strength development of ultra-high performance concrete(UHPC) with cement-silica fume-slag binder.This numerical procedure started with initial packing behavior of designed UHPC using a random sequential packing method.Furthermore,synergistic effect of combined mineral admixtures was addressed with respect to hydration heat.Accordingly,hydration degree of cement and reaction degrees of mineral admixtures were determined based on a blended cement hydration model.Finally,a compressive strength evolution model was proposed and the evolution of compressive strength of three mixes with different binder recipes was compared.The results showed that the both initial packing behavior of UHPC mixes and synergistic effect of mineral admixtures are critical for predicting the properties of UHPC.A remarkable void fraction of 0.2042 was observed for UHPC mix designed by optimization algorithms under random packing.Furthermore,a negative synergistic effect of the combination of silica fume and slag was obtained with regarding to compressive strength.In addition,for a given mineral admixture replacement of 20%,the formulation of mineral admixture should be carefully tailored where the UHPC incorporating 5%silica fume and 15%slag shows the highest compressive strength.

高强钢筋增强UHPC-CFST组合桥墩抗震性能研究

采用有限元软件ABAQUS,开展了高强钢筋增强UHPC-CFST组合桥墩的抗震数值建模分析,通过与已有试验结果的对比,验证了建模方法的准确性。在此基础上,分析了轴压比、UHPC强度、UHPC厚度和钢管屈服强度等参数对组合桥墩受力性能的影响规律,并给出了各参数的建议取值范围。研究结果表明:增大轴压比和纵筋配筋率可提升组合桥墩的水平承载力和耗能能力,然而会限制试件的变形;提高UHPC强度和UHPC厚度,组合桥墩的水平承载力和位移延性系数均呈现出先增大后减小的趋势;提升钢管屈服强度可稳步增强组合桥墩的水平承载力;增加钢管厚度可明显提升组合桥墩的抗震性能,而体积配箍率和混凝土强度对组合桥墩的抗震性能影响较小。基于分析数据样本,采用多元非线性回归分析得到水平峰值荷载和位移延性系数的计算方法,公式计算值与有限元分析值吻合良好。

高强钢丝布增强UHPC约束混凝土柱轴压性能

为掌握新型高强钢丝布增强超高性能混凝土(UHPC)的约束效应,研究高强钢丝布面密度和层数变化对约束混凝土柱轴压性能的影响规律.首先,利用混凝土泊松比、延性指数和韧性指数对高强钢丝布增强UHPC的约束效应进行评估;其次,考虑高强钢丝布与UHPC提供的约束力,建立复合约束层的侧向约束力模型;最后,基于Ottosen破坏准则和有效约束指标,建立约束混凝土轴压本构模型.研究结果表明:约束柱受压时呈明显的延性破坏,高强钢丝布增强UHPC约束体系可有效抑制裂缝发展,减缓加载后期试件刚度退化;与未约束柱相比,约束柱极限承载力、峰值压应变和峰值应力的最大增幅分别为147.0%、104.0%和58.0%;当高强钢丝布层数从1层增加至2层,面密度增加至3.3倍时,约束柱极限承载力、峰值压应变和峰值应力分别提高了8.4%、29.3%和15.8%,延性指数和韧性指数分别提高了50.3%和44.2%.对比经典约束混凝土轴压本构模型,本文建立的模型结果与试验结果吻合度较高.