Investigation of plateau basin crustal structures and thickening mechanisms in the northeastern margin of the Tibetan plateau

This paper uses deep seismic sounding （DSS） data to contrast and analyze the crustal structures of three plateau basins （Songpan-Garze, Qaidam, Longzhong） in the northeastern margin of the Qinghai-Xizang （Tibetan） plateau, as well as two stable cratonic basins （Ordos, Sichuan） in its peripheral areas. Plateau basin crustal structures, lithological variations and crustal thickening mechanisms were investigated. The results show that, compared to the peripheral stable cratonic basins, the crystalline crusts of plateau basins in the northeastern margin are up to 10 15 km thicker, and the relative medium velocity difference is about 5% less. The medium velocity change in crustal layers of plateau basin indicates that the upper crust undergoes brittle deformation, whereas the lower crust deforms plastically with low velocity. The middle crust shows a brittle-to-plastic transition zone in this region. Thickening in the lower crust （about 5 10 km）, and rheological characteristics that show low- medium velocity （relatively reduced by 7%）, suggest that crustal thickening mainly takes place in lower crust in the northeastern margin of the Tibetan plateau. The crust along the northeastern margin shows evidence of wholesale block movement, and crustal shortening and thickening seem to be the main deformation features of this region. The GPS data show that the block motion modes and crustal thickening in the Tibetan plateau is closely related to the peripheral tectonic stress field and motion direction of the Indian plate. The Mani-Yushu- Xianshuihe fold belt along the boundary between the Qiangtang block and the Bayan Har block divides the different plateau thickening tectonic environments into the middle-western plateau, the northeastern margin and the southeastern plateau.

Representative value of cross-fault in the northeastern margin of the Qinghai-Tibet block and case analysis of the 2016 Menyuan Ms6.4 earthquake

The equation for determining cross-fault representative value is calculated based on hanging wall and foot wall reference level surfaces. The cross-fault data reliability are analyzed base on the stability of reference datum and observation points, thereby facili- tating plotting of the representative value curves after removing interference. The spatial and temporal characteristics of fault deformation abnormalities before the 2016 Menyuan Ms6.4 earthquake, as well as the fault-movement characteristics reflected by representa- tive value, are summarized. The results show that many site trends had changed 1-3 years before the Menyuan Ms6.4 earthquake in the Qilian Fault, reflecting certain background abnormalities. The short-term abnormalities centrally had appeared in the 6 months to 1 year period before the earthquake near and in the neighborhood of the source region, demonstrating a significantly increased number of short-term abnormalities. Many sites near and in the neighborhood of the source region had strengthened inverse activities or had changed from positive to inverse activities in the most recent 2-3 years, which reflect stress-field enhancements or adjustment features.

The Early Breakup of Rodinia Supercontinent in the Northeastern Margin of the Yangtze Plate： New Evidence from SIMS Zircon Ages of the Granitic Gneiss from the Chaolian Island, Shandong Peninsula

The amalgamation and breakup mechanisms of the Rodinia supercontinent during the Meso- and Neoproterozoic have been the focus of much research. However, few studies have examined the response of Neoproterozoic tectonics and magmatism along the northeastern margin of the Yangtze Plate to synchronous global events. The Qianliyan Uplift is located on the eastern margin of the Sulu orogenic belt in the ocean, but the tectonic affinity of the uplift and its relationship to the Sulu orogenic belt remains unclear. In this study, we investigated the formation age, geochemical characteristics, genesis type, and affinity of the granitic gneiss on Chaolian Island of the Qianliyan uplift and its tectonic significance.

The geological structure background and the crustal structure in the northeastern margin of the Qinghai-Tibetan plateau

The geological structure background, the crustal structure and the shape of Moho in the northeastern margin of the Qinghai-Tibetan plateau are studied. Based on artificial seismic sounding profile as well as geological data. The main results are summarized as follows: (1) The geotectonic subdivisions and the characteristics of main deep and large faults in the northeastern margin of the Qinghai-Tibetan plateau are presented; (2) The general features of the Moho are obtained mainly based on artificial seismic sounding data; (3) There exists well corresponding relation between surface faults and some features of the Moho, which suggests that such complex crustal structure might be the preparation environment of strong earthquakes.

Numerical simulation of temporal and spatial evolution of fold-thrust belts in the northern and northeastern margins of the Qinghai-Tibetan Plateau

Fold-thrust belts are common structural styles under the background of long-term regional tectonic shortening.The northern and northeastern margins of the Qinghai-Tibetan Plateau are located on the edge of the growth and expansion of the Qinghai-Tibetan Plateau.Since nearly 10 Ma,some significant and typical fold thrust belt have been formed.The spatial-temporal evolution of these fold-thrust belts and the characteristics of surface deformations are significant issues in geodynamics.In this paper,we use the elastoplastic finite element model with considering the contact nonlinearity to study the spatialtemporal evolution of the fold-thrust belts in the northern and northeastern margins of the Qinghai-Tibetan Plateau,with particular attention to the details of the relationship between the depth and the shallow,the spatialtemporal order,and the characteristics of the surface deformation,etc.,in order to make a relatively complete mechanical interpretation of the spatial-temporal evolution of the foldthrust belts in the northern and northeastern margins of the Qinghai-Tibetan Plateau from the perspective of geodynamics.

Gravity evidence of underplating in the northeastern margin area of Qinghai-Tibet plateau

Based on leveling data in 1972 -2011 and relative-gravity data in 1993 -2011, we obtained a longterm vertical crustal-deformation rate of 1.62mm/a and a relative-gravity variation rate of 0.62 × 10^-8 ms^-2a^-1 for the northeastern margin area of Qinghai-Tibet plateau. After removing the contributions from the observed vertical movement and inferred surface denudation, we obtain a gravity-variation rate of 0.73 × 10^-8 ms^-2a^-1 attributable to the mass changes beneath the crust. This positive change suggests that the total mass under the observation stations was gradually increasing. We consider this result to be the gravitational evidence of underplating beneath the study area, and propose that the underplating was caused by collision betwen the Indian plate and Tibetan plateau and by gravitation-potential induced deviatoric stress.

Formation and Evolution of the Late Mesozoic-Cenozoic Ruo'ergai Basin,Northeastern Margin of the Qinghai-Tibet Plateau

The Middle Triassic Ladinian-Upper Triassic Norian series in the Mesozoic-Cenozoic Ruo’ergai basin of Songpan area is characterized of large thick shallow marine-deep marine fine grained clastic.The strata are regionally unconformable between each adjacent two of the Middle-Late Triassic fine grained clastic,the Jurassic coal-containing clastic,the Cretaceous-Paleogene variegated coarse clastic。

The Present Space-Time Motion and Deformation Features of the Northeastern Margin of the Qinghai-Xizang(Tibet) Block and Its Adjacent Area

On the basis of Discontinuous Deformation Analysis (DDA), and considering the moderate intrusion of specific block boundaries to different extents, the first-order block motion model is established for the northeastern margin of Qinghai-Xizang(Tibet) block and the kinematical model for depicting deformation of small regions as well by using GPS observations of three periods (1991, 1999 and 2001). By simulating, we obtained the motion features of the first-order blocks between the large WWN faults on the sides of the studied region, the distribution features of the principal strain rate field and the inhomogeneous motion features with space-time of the faults in the northern boundary of the Qinghai-Xizang (Tibet) block.

Modeling the Dynamic Gravity Variations of Northeastern Margin of Qinghai-Xizang (Tibet) Plateau by Using Bicubic Spline Interpolation Function

In this paper, the spatial-temporal gravity variation patterns of the northeastern margin of Qinghai-Xizang (Tibet) Plateau in 1992～2001 are modeled using bicubic spline interpolation functions and the relations of gravity change with seismicity and tectonic movement are discussed preliminarily. The results show as follows: ① Regional gravitational field changes regularly and the gravity abnormity zone or gravity concentration zone appears in the earthquake preparation process; ② In the significant time period, the gravity variation shows different features in the northwest, southeast and northeast parts of the surveyed region respectively, with Lanzhou as its boundary; ③ The gravity variation distribution is basically identical to the strike of tectonic fault zone of the region, and the contour of gravity variation is closely related to the fault distribution.

Numerical simulation of tectonic stress and strain rate fields in the northeastern margin of the Tibetan Plateau in association with major fault zones

A series of large strike-slip and thrust faults have developed in the northeastern margin of the Tibetan Plateau since the Late Cenozoic,with strong and active tectonic activity and frequent occurrences of large earthquakes.Modulation of regional tectonic stress distribution,strain fields,and seismic hazards has not been well studied.This study introduces a three-dimensional viscoelastic finite element numerical model to calculate crustal stress and strain rate fields under current tectonic loading.The preliminary results show that the direction of the horizontal principal compressive stress rate and compressive horizontal principal strain rate in the northeastern margin of the Tibetan Plateau rotate clockwise as a whole,and this rotation is more significant in the southeast direction because of the block of the Alxa and the Ordos blocks.The NE-SW horizontal principal compressive stress rate and SE horizontal tensile stress rate dominate the entire study region.The maximum value of the horizontal principal compressive strain rate at a depth of 0 km in the model is approximately 4×10^(-8)yr^(-1)near the East Kunlun fault and is smaller in the stable Alxa and Ordos blocks at approximately 1×10^(-8)yr^(-1).The calculated regional stress state is in good agreement with the actual focal mechanism solution,indicating that strike-slip and thrust stress fields dominate the northeastern margin of the Tibetan Plateau.The Altyn Tagh,East Kunlun,and Haiyuan faults demonstrate that the maximum shear strain rate gradually decreases eastward,and the decrease in the maximum shear strain rate value is absorbed by orogenic uplift and crustal shortening at its boundaries.The western section of the Altyn Tagh fault,west-to-middle sections of the East Kunlun fault,and west-to-middle sections of the Haiyuan fault will have high seismic hazards in the future.

Crustal structure of northeastern margin of the Tibetan Plateau by receiver function inversion

Using seismic data of about one year recorded by 18 broadband stations of ASCENT project,we obtained 2547 receiver functions in the northeastern Tibetan Plateau.The Moho depths under 14 stations were calculated by applying the H-κ domain search algorithm.The Moho depths under the stations with lower signal-noise ratio(SNR) were estimated by the time delay of the PS conversion.Results show that the Moho depth varies in a range of ~40–60 km.The Moho near the Haiyuan fault is vague,and its depth is larger than those on its two sides.In the Qinling-Qilian Block,the Moho becomes shallower gradually from west to east.To the east of 105°E,the average depth of the Moho is 45 km,whereas the west is 50 km or even deeper.Combining our results with surface wave research,we suggest a boundary between the Qinling and the Qilian Mountains at around 105°E.S wave velocities beneath 15 stations have been obtained through a linear inversion by using Crust2.0 as an initial model,and the crustal thickness that was derived by H-κ domain search algorithm was also taken into account.The results are very similar to the results of previous active source studies.The resulting figure indicates that low velocity layers developed in the middle and lower crust beneath the transition zone of the Tibet Block and western Qinling,which may be related to regional faults and deep earth dynamics.The velocity of the middle and lower crust increases from the Songpan Block to the northeastern margin of Tibetan Plateau.Based on the velocity of the crust,the distribution of the low velocity zone and the composition of the curst(Poisson's ratio),we infer that the crust thickening results from the crust shortening along the direction of compression.

Dextral strike-slip of Sanguankou-Niushoushan fault zone and extension of arc tectonic belt in the northeastern margin of the Tibet Plateau

Sanguankou-Niushoushan 差错(SGK-NSSF ) 的运动学的特征具有到弧的延期的理解的大意义在西藏高原的东北边缘的构造的带。用地调查和各种各样的数据收集方法，包括大规模地质的印射，典型地形学的测量，并且沉积阶层标明日期， SGK-NSSF 展出明显的右罢工滑倒特征并且因此不是一个左首的罢工滑倒差错，由以前的研究人员相信了，这被决定。这研究的结果证明地质的边界为古生代，中生代，和新生代时代都被差错右地打乱，与是类似的指责的排水量。在地志的效果的消除以后，差错的最大的罢工滑倒排水量被发现是

The U-Pb chronologic evidence and sedimentary responses of Silurian tectonic activities at northeastern margin of Tarim Basin

U-Pb ages of Devonian detrital zircons from Tabei Uplift have been determined through LA-ICP-MS test technology.The results revealed that most zircon ages concentrate on 460-414 Ma,especially around 436-423 Ma,indicating possible occurrences of strong tectonic events at the northern margin of Tarim Basin during that period.Combined with previous researches on the basin marginal orogenic belts,intense tectonic activities developed at the northeast margin of Tarim Basin and its obvious sedimentary responses in basin during the end of Ordovician to Early-Middle Silurian are discussed.These include(1) several unconformities within the Late Ordovician-Silurian,showing truncation,erosion,and onlap characteristics,which reflected the local uplift formed during the surrounding extrusion process;(2) the Silurian fluvial delta system from northeast to southwest in Keping,Yingmaili,Hade,and Caohu areas,which reflected the partial uplift at the northeast margin and provided clastic supply to basin;and(3) as indicated by heavy mineral analysis,the Silurian sediments came mainly from the recycles of orogenic belts provenance,which indicated the compress tectonic setting.In addition,a wide range of red mudstone layer distribution in the upper part of the Silurian may be closely related to the surrounding tectonic uplift and the rapid decline of sea levels.

Influence of mantle convection to the crustal movement pattern in the northeastern margin of the Tibetan Plateau based on numerical simulation

Based on the recent observations about the movement and rheological structure of the lithosphere and deformation pattern of the crust, we developed a three-dimensional finite element model for the northeastern margin of the Tibetan Plateau.The model considered the impacts of both external and internal conditions, including mantle convection, gravitational potential energy and block interactions. We compared the simulated surface movement rates to the observed GPS velocities, and the results revealed that crustal movement gradually decreased toward the edge of the plateau. The factors controlling this pattern are the interactions of adjacent blocks, gravitational potential energy of the plateau, and also mantle convection as well. Additionally,according to the observation that there was an apparent difference between the horizontal movement rate of the lithosphere and convective velocity of the underlying mantle, and also based on the results of seismic anisotropy studies that suggest different strengths and deformation regimes of the lithosphere in different tectonic blocks, we proposed that the impact of mantle convection on the lithosphere may have varied in space, and introduced a parameter named mantle convection intensity factor in numerical simulations. Our simulation results show consistent surface movement rates with GPS observations, which further supports the viewpoint of seismic anisotropy studies, i.e., the degree of coupling between the crust and mantle varies significantly among different blocks.

Crustal P-wave velocity structure in the northeastern margin of the Qinghai-Tibetan Plateau and insights into crustal deformation

The transitional area between the northeastern margin of the Qinghai-Tibetan Plateau, Ordos Block and Alxa Block,also being the northern segment of the North-South Seismic Belt, is characterized by considerably high seismicity level and high risk of strong earthquakes. In view of the special tectonic environment and deep tectonic setting in this area, this study used two seismic wide-angle reflection/refraction cross profiles for double constraining, so as to more reliably obtain the fine-scale velocity structure characteristics in both the shallow and deep crust of individual blocks and their boundaries in the study area,and further discuss the seismogenic environment in seismic zones with strong historical earthquakes. In this paper, the P-wave data from the two profiles are processed and interpreted, and two-dimensional crustal velocity structure models along the two profiles are constructed by travel time forward modeling. The results show that there are great differences in velocity structure,shape of intra-crustal interfaces and crustal thickness among different blocks sampled by the two seismic profiles. The crustal thickness along the Lanzhou-Huianbu-Yulin seismic sounding profile(L1) increases from ~43 km in the western margin of Ordos Block to ~56 km in the Qilian Block to the west. In the Ordos Block, the velocity contours vary gently, and the average velocity of the crust is about 6.30 km s-1; On the other hand, the velocity structures in the crust of the Qilian Block and the arclike tectonic zone vary dramatically, and the average crustal velocities in these areas are about 0.10 km s-1 lower than that of the Ordos Block. In addition, discontinuous low-velocity bodies(LVZ1 and LVZ2) are identified in the crust of the Qilian Block and the arc-like tectonic zone, the velocity of which is 0.10–0.20 km s-1 lower than that of the surroundings. The average crustal thickness of the Ordos Block is consistently estimated to be around 43 km along both Profile L2(Tongchuan-Huianbu-Alashan left banner seismic sounding profile) and Profile L1. In contrast to the gently varying intra-crustal interfaces and velocity contours in the Ordos Block along Profile L1, which is a typical structure characteristic of stable cratons, the crustal structure in the Ordos Block along Profile L2 exhibits rather complex variations. This indicates the presence of significant structural differences in the crust within the Ordos Block. The crustal structure of the Helan Mountain Qilian Block and the Yinchuan Basin is featured by "uplift and depression" undulations, showing the characteristics of localized compressional deformation.Moreover, there are low-velocity zones with alternative high and low velocities in the middle and lower crust beneath the Helan Mountain, where the velocity is about 0.15–0.25 km s-1 lower than that of the surrounding areas. The crustal thickness of the Alxa Block is about 49 km, and the velocity contours in the upper and middle-lower crust of the block vary significantly. The complex crustal velocity structure images along the two seismic sounding profiles L1 and L2 reveal considerable structural differences among different tectonic blocks, their coupling relationships and velocity structural features in the seismic zones where strong historical earthquakes occurred. The imaging result of this study provides fine-scale crustal structure information for further understanding the seismogenic environment and mechanism in the study area.

2023年甘肃积石山6.2级地震发震构造浅析

2023年12月18日23时59分,甘肃临夏州积石山县发生6.2级地震,造成人员伤亡和财产损失。本次地震发生在青藏高原东北缘地区,受青藏高原向NE向扩展挤压作用的影响,区域发育两组较为典型的断裂构造:NWW向大型左旋走滑断裂带是活动块体运动边界,另一组NNW向右旋走滑断裂则发育在块体内部构成次级块体边界。此次积石山6.2级地震就发生在NWW向西秦岭北缘左旋走滑断裂带和NNW向日月山右旋走滑断裂带之间的大型挤压阶区内,初步判定其发震构造为以逆冲作用为主的拉脊山断裂带东南段的积石山东缘断裂。余震展布范围严格限制在黄河以南的积石山东麓大河家第三系盆地内,根据黄河以北拉脊山和以南的积石山山脊线及坡折带存在较大不连续性,且沿黄河南岸发育较明显的断层三角面等构造地貌特征,推测沿黄河发育有一条调节区内挤压变形差异的横向断裂。断裂切断拉脊山北缘断裂带东南段,使积石山东缘断裂成为一个长度不足40 km的独立活动段,判定原震区近期发生更大地震的可能性不大。

2023年12月18日甘肃省积石山6.2级地震的控震构造及特征

2023年12月18日23时59分在甘肃省临夏州积石山县发生6.2级地震,造成了严重人员伤亡,及时了解此次地震的发震构造及其特征,对于分析区域未来强震危险性具有重要意义。综合区域地震构造、地质、震源机制、地震烈度和余震重定位等资料,对此次地震的控震构造及特征进行综合分析后认为,此次强震是发生在西宁—兰州断块内部的一次北北西向逆冲断层作用事件,距震中最近的拉脊山逆冲断裂带构成了此次地震的控震构造。该断裂带处于北西向日月山右旋走滑断层与北西西向西秦岭北缘左旋走滑断层交汇部位,整体呈北西至北北西向弧形展布,包含了南缘与北缘两条倾向相反的分支断裂带。震中位置、余震及烈度分布等数据指示此次地震的具体发震断层为拉脊山北缘逆冲断裂带南段的东支断层带,余震分布和极震区范围等符合逆断层型地震的上盘效应特征,但是否引起同震地表变形,还需进一步的现场调查确定。综合研究认为,此次积石山地震是在印度与欧亚板块持续陆陆碰撞作用下,青藏高原东北缘的西宁—兰州断块沿海原左旋走滑断裂向东侧向滑移过程中,在北东向挤压构造应力场下,引发日月山断层与西秦岭北缘断层构成的区域共扼走滑断裂系交汇挤压部位发生逆断层活动的结果。此次强震进一步指示青藏高原东缘的向东挤出构造体系仍是近年来我国陆内强震活动的主要控震构造,并警示应重视活断层相对发育的断块内部城镇密集区的强震灾害风险。

华北克拉通东北缘改造:来自吉林辉南地区构造热事件的古地磁记录

华北克拉通东北缘处于构造运动活跃地区,古地磁研究可为构造演化和岩浆热事件提供依据。笔者在吉林辉南地区中寒武统32个采点共采集246块样品进行了岩石学、岩石磁学及系统热退磁实验。古地磁实验表明,徐庄组砂质泥岩主要磁性矿物是赤铁矿和磁铁矿,张夏组灰岩主要磁性矿物是颗粒较小的磁铁矿和黄铁矿,且均发生了重磁化,并记录了稳定的中温分量,前者中温分量地理坐标平均方向为D/I=10.9°/50.8°,α_(95)=11.7°,对应的极位置为76°N,264.6°E,A_(95)=13°,与早白垩世岩浆活动记录的古地磁极位置一致;后者中温分量地理坐标平均方向为D/I=29.1°/59.0°,α_(95)=6.5°,对应的极位置为68°N,213.7°E,A_(95)=8.4°,与第四纪火山岩记录的古地磁极位置一致。综合区域地质背景分析,早白垩世—第四纪,吉林辉南及邻区古地磁记录的2次较为强烈的构造热事件,以及因敦化-密山断裂带左旋走滑运动造成的北向运移形成的古纬度差,一定程度上对华北克拉通东北缘起到双重改造作用。

六盘山地区新生代构造演化:来自锆石和磷灰石裂变径迹的证据

青藏高原的隆升与扩展不仅导致欧亚大陆内部发生强烈的构造变形,亦对高原周缘的地貌格局及气候变化产生了重大影响.青藏高原东北缘新生代以来的隆升时代与响应过程一直备受争议,而界定青藏高原东北缘构造带隆升时序是解决争议的关键之一.本研究围绕青藏高原东北缘,在陇中盆地、六盘山褶皱逆冲带和鄂尔多斯地块西南缘地区进行了磷灰石和锆石裂变径迹测试分析和热史模拟.测试分析结果表明研究区样品的磷灰石裂变径迹年龄范围分布于136~16 Ma,裂变径迹的长度范围介于11.9~13.3μm;锆石裂变径迹年龄结果为258~79 Ma,但多数样品的年龄介于160~99 Ma;热史模拟结果揭示了研究区新生代以来至少经历了两期隆升和冷却降温事件,即始新世期间(55~30 Ma)和中中新世(17~12 Ma)以来.始新世期间(55~30 Ma)发生的隆升事件可能是印度大陆与欧亚大陆陆陆碰撞远程效应的直接响应,表明印度与欧亚大陆碰撞之初或不久,其应力即已传导至东北缘边界;中中新世(17~12 Ma)以来的隆升剥露冷却事件奠定了青藏高原东北缘现今构造格局.

柴北缘骆驼泉剖面新生代地层磁组构特征及其构造意义

青藏高原东北部新生代构造演化对理解高原隆升和变形模式具有重要意义,而目前对于该地区挤压应力方向转变过程仍存在很大争议.本文对柴北缘逆冲带北西部骆驼泉剖面新生代地层开展系统磁组构(本文特指磁化率各项异性)研究,以揭示该地区挤压应力方向的转变特征.系统岩石磁学结果表明,骆驼泉剖面新生代样品中主要磁性矿物是顺磁性组分和赤铁矿以及少量磁铁矿.通过对磁组构特征分析及其与古水流方向对比表明,骆驼泉剖面新生代地层磁组构主要为初始变形磁组构,可用于指示沉积成岩时期的挤压应力方向.磁组构结果揭示,骆驼泉地区挤压应力方向在上干柴沟组下部沉积时期为NNE-SSW向,而上干柴沟组上部和油砂山组沉积时期转变为NE-SW向.结合柴北缘逆冲带已有磁组构结果指出,该地区早期N-S向或NNE-SSW向挤压应力可能与印度—欧亚板块早新生代以来近N-S向碰撞挤压过程有关,指示印度—欧亚碰撞的挤压应力自下干柴沟组下部沉积时期就已传播至高原东北部地区;而后期NE-SW向挤压应力方向与该地区现今GPS揭示的上地壳运动方向一致,可能与该时段高原东北部巨型走滑断裂构造体系(尤其是阿尔金断裂)有关.此外,柴北缘逆冲带新生代挤压应力方向转变在其北西部起始于上干柴沟组下部沉积时期,而南东部起始于上油砂山组下部沉积时期,与地震反射剖面揭示的断裂活动等地质证据共同揭示柴北缘逆冲带新生代的构造活动自靠近阿尔金断裂的北西部向南东部传播和扩展.综合分析青藏高原东北部地区挤压应力方向转变和其他地质证据发现,挤压应力方向转变显示出自柴北缘逆冲带北西部向东、西和南向扩展特征,与阿尔金断裂在上干柴沟组下部-上油砂山组下部沉积时期剪切应力集中于断裂本身,而上油砂山组下部沉积以来开始散布于高原东北部内部地区的两阶段走滑活动相关.