Experimental study on atomization characteristics and dust-reduction performance of four common types of pressure nozzles in underground coal mines

Pressure nozzle is commonly used in the dust-reduction techniques by spraying of underground coal mines.Based on the internal structure,the pressure nozzle can be divided into the following types:spiral channel nozzle,tangential flow-guided nozzle and X-swirl nozzle.In order to provide better guidance on the selection of nozzles for the coal mine dust-reduction systems by spraying,we designed comparing experiments to study the atomization characteristics and dust-reduction performance of four commonly used nozzles in the coal mine underground with different internal structures.From the experimental results on the atomization characteristics,both the tangential flow-guided nozzle and the X-swirl nozzle have high flow coefficients.The atomization angle is the largest in the spiral non-porous nozzle,and smallest in both the X-swirl nozzle and the spiral porous nozzle.The spraying range and the droplet velocity are inversely proportional to the atomization angle.When the water pressure is low,the atomization performance of the spiral non-porous nozzle is the best among the four types of nozzles.The atomization performance of the X-swirl nozzle is superior to other types when the water pressure is high.Under the high water pressure,the particle size of the atomized droplets is smallest in the X-swirl nozzle.Through the experiments on the dust-reduction performance of the four types of nozzles and the comprehensive analysis,the X-swirl nozzle is recommended for the coal mine application site with low water pressure in the dust-reduction system,while at the sites with high water pressure,the spiral non-porous nozzle is recommended,which has the lowest water consumption and obvious economic advantages.

An experimental study on the atomization characteristics of the nozzle for the after-pot cooling of galvanized steel sheets

Air-atomized fog cooling is particularly suitable for the after-pot cooling of galvanized steel strips.With air and water serving as working media,an experimental study was conducted on the atomization characteristics of a newly-developed cross-flow type of fog nozzles.The water flux distribution,spray angle and pressure of water and air were measured.The results show that the water droplet size was small and insensitive to the water flow rate.The spray angle was small and the water flow rate slightly affected the air pressure in the chamber.An empirical correlation between the pressure in the chamber and the gas flow rate was obtained for the purpose of equipment design.

Jet Characteristics and Optimization of a Cavitation Nozzle for Hydraulic Fracturing Applications

Hydraulic jetting is a form of fracturing that involves using a high-pressure jet of water to create fractures in the reservoir rock with a nozzle serving as the central component of the hydraulic sandblasting perforation tool.In this study,the flow behavior of the nozzle is simulated numerically in the framework of a SST k-ωturbulence model.The results show that the nozzle structure can significantly influence the jet performance and related cavitation effect.Through orthogonal experiments,the nozzle geometric parameters are optimized,and the following configuration is found accordingly:contraction angle 20°,contraction segment length 6 mm,cylindrical segment diameter 6 mm,cylindrical segment length 12 mm,spread segment length 10 mm,and spread angle 55°.

Effect of droplet characteristics on liquid-phase distribution in spray zone of internal mixing air-mist nozzle

In continuous casting production,droplet characteristics are important parameters for evaluating the nozzle atomization quality,and have a significant impact on the secondary cooling effect and the slab quality.In order to study the behavior of atomized droplets after reaching the slab surface and to optimize the spray cooling effect,the influence of droplet diameter and droplet velocity on the migration behavior of droplets in the secondary cooling zone was analyzed by FLUENT software.Results show that the droplets in the spray zone and on the slab surface are mainly concentrated in the center,thus,the liquid volume fraction in the center is higher than that of either side.As the droplet diameter increases,the region of high liquid volume fraction on the slab surface becomes wider,and the liquid phase distribution in the slab width direction becomes uneven.Although increasing the droplet velocity at the nozzle exit has little effect on droplet diffusion in the spray zone,the distribution becomes more uneven due to more liquid reaches the slab surface per unit time.A prediction formula of the maximum water flow rate on the slab surface for specific droplet characteristics was proposed based on dimensionless analysis and validated by simulated data.A nozzle spacing of 210 mm was recommended under the working conditions in this study,which ensures effective coverage of the spray water over the slab surface and enhances the distribution uniformity of water flow rate in the transverse direction.

Investigations of the effects of two typical jet crushing methods on the atomization and dust reduction performance of nozzles

Single-fuid nozzles and dual-fuid nozzles are the two typical jet crushing methods used in spray dust reduction. To distinguish the atomization mechanism of single-fuid and dual-fuid nozzles and improve dust control efciency at the coal mining faces, the atomization characteristics and dust reduction performance of the two nozzles were quantitatively compared. Results of experiments show that, as water supply pressure increased, the atomization angle of the swirl pressure nozzle reaches a maximum of 62° at 6 MPa and then decreases, but its droplet size shows an opposite trend with a minimum of 41.7 μm. The water supply pressure helps to improve the droplet size and the atomization angle of the internal mixing air–liquid nozzle, while the air supply pressure has a suppressive efect for them. When the water supply pressure is 0.2 MPa and the air supply pressure reaches 0.4 MPa, the nozzle obtains the smallest droplet size which is 10% smaller than the swirl pressure nozzle. Combined with the dust reduction experimental results, when the water consumption at the working surface is not limited, using the swirl pressure nozzle will achieve a better dust reduction efect. However, the internal mixing air–liquid nozzle can achieve better and more economical dust reduction performance in working environments where water consumption is limited.

Effect of Intake Conditions and Nozzle Geometry on Spray Characteristics of Group-Hole Nozzle

The group-hole nozzle concept is proposed to meet the requirement of nozzle hole minimization and reduce the negative impact of poor spatial spray distributions.However,there are limited researches on the effects of intake conditions and nozzle geometry on spray characteristics of the group-hole nozzle.Therefore,in this study,an accurate spray model coupled with the internal cavitating flow was established and computational fluid dynamics(CFD)simulations were done to study the effects of intake conditions and nozzle geometry on spray characteristics of the group-hole nozzle.Experimental data obtained using high-speed digital camera on the high-pressure common rail injection system was used to validate the numerical model.Effects of intake conditions(injection pressure and temperature)and nozzle geometry(orifice entrance curvature radius and nozzle length)on the flow and spray characteristics of the group-hole nozzle were studied numerically.The differences in Sauter mean diameter(SMD),penetration length and fuel evaporation mass between single-hole nozzle and group-hole nozzle under different nozzle geometry were also discussed.It was found that the atomization performance of the group-hole nozzle was better than that of the single-hole nozzle under same intake conditions,and the atomization effect of the short nozzle was better than that of the long nozzle.With increase in the orifice entrance curvature radius,the average velocity and turbulent kinetic energy of the fuel increased,which was conducive to improving the injection rate and flow coefficient of the nozzle.Meanwhile,the penetration length and SMD value rose,while evaporation mass dropped.When the ratio of the orifice entrance curvature radius(R)to the diameter of injection hole(D)was 0.12,the spray characteristics reached a constant state due to elimination of cavitation.Conclusions were made based on these.This study is expected to be a guide for the design of the group-hole nozzle.

Comparative study on the flow fields of three atomization nozzles

In this paper, the flow fields of three types of nozzles （ Hartmann, Laval and Laminar nozzles ） under the same conditions are simulated, and the corresponding to pressure, temperature, velocity and turbulence intensity are obtained. The results suggest that two crushing presents in the atomization process using Hartmann nozzle, but only one crushing presents in the atomization process using the other nozzles, through the comparative research on the flow field features of three types of nozzle. Furthermore, the shockwave plays a more important role in crushing of liquid metal than velocity.

Design and Atomization Characteristic of Laval-style Annular Slot Nozzle

Gas mass flux rate,metal mass flux rate and outlet gas velocity are three atomization scale parameters which greatly affect the atomization efficiency. A Laval-style annual slot supersonic nozzle is designed by optimizing the geometric parameters of delivery tube outlet and gas outlet to obtain applicable atomization scale parameters. A computational fluid flow model is adopted to investigate the effect of atomization gas pressure ( P0 ) on the gas flow field in gas atomization progress. The numerical results show that the outlet gas velocity of the nozzle is not affected by P0 and the maximum gas velocity reaches 452 m / s. The alternation of aspiration pressure ( ΔP) is caused by the variations of stagnation pressure and location of Mach shock disk, and hardly by the location of stagnation point. The aspiration pressure is found to decrease as P0 increases when P0 < 1. 3 MPa. However,at a higher atomization gas pressure increasing P0 causes an opposite: the aspiration pressure atomization increases with the gas pressure,and keeps a plateau when P0 > 2. 0 MPa. The minimum aspiration pressure ΔP = - 70 kPa is obtained at P0 = 1. 3 MPa. The results indicate that the designed Laval- style annual slot nozzle has well atomization characteristic at lower atomization pressure.

Design and Fluid-Dynamic Analysis of a Flushing Nozzle for Drilling Applications

The actuator is a key component of the creaming tool in drilling applications.Its jet performances determine the effective reaming efficiency.In this work,a new selective reaming tool is proposed and the RNG k-εturbulence model is used to calculate its internal and externalflowfields.In particular,special attention is paid to the design of theflushing nozzle.The results show that the jet originating from theflushing nozzle has a significant influence on rock cutting and blade cooling effects.In turn,the jet performances depend on geometric structure of the creaming actuator.In this framework,a conical-cylindrical nozzle with a diameter of 7 mm is initially considered as a basis to implement a strategy to optimize the structural parameters of the reaming actuator,and improve the related side tracking reconstruction technology.

Numerical simulation of the dimensional transformation of atomization in a supersonic aerodynamic atomization dust-removing nozzle based on transonic speed compressible flow

To simulate the transonic atomization jet process in Laval nozzles,to test the law of droplet atomization and distribution,to find a method of supersonic atomization for dust-removing nozzles,and to improve nozzle efficiency,the finite element method has been used in this study based on the COMSOL computational fluid dynamics module.The study results showed that the process cannot be realized alone under the two-dimensional axisymmetric,three-dimensional and three-dimensional symmetric models,but it can be calculated with the transformation dimension method,which uses the parameter equations generated from the two-dimensional axisymmetric flow field data of the three-dimensional model.The visualization of this complex process,which is difficult to measure and analyze experimentally,was realized in this study.The physical process,macro phenomena and particle distribution of supersonic atomization are analyzed in combination with this simulation.The rationality of the simulation was verified by experiments.A new method for the study of the atomization process and the exploration of its mechanism in a compressible transonic speed flow field based on the Laval nozzle has been provided,and a numerical platform for the study of supersonic atomization dust removal has been established.

Process modeling gas atomization of close-coupled ring-hole nozzle for 316L stainless steel powder production

The paper aims at modeling and simulating the atomization process of the close-coupled ring-hole nozzle in vacuum induction gas atomization(VIGA)for metallic powder production.First of all,the primary atomization of the ring-hole nozzle is simulated by the volume of fluid(VOF)coupled large eddy simulation(LES)model.To simulate the secondary atomization process,we use the method of selecting the droplet sub-model and the VOF model.The results show that the ring-hole nozzle forms a gas recirculation zone at the bottom of the delivery tube,which is the main reason for the formation of an annular liquid film during the primary atomization.In addition,the primary atomization process of the ring-hole nozzle consists of three stages:the formation of the serrated liquid film tip,the appearance and shedding of the ligaments,and the fragmentation of ligaments.At the same time,the primary atomization mainly forms spherical droplets and long droplets,but only the long droplets can be reserved and proceed to the secondary atomization.Moreover,increasing the number of ring holes from 18 to 30,the mass median diameter(MMD,d_(50))of the primary atomized droplets decreases first and then increases,which is mainly due to the change of the thickness of the melt film.Moreover,the secondary atomization of the ring-hole nozzles is mainly in bag breakup mode and multimode breakup model,and bag breakup will result in the formation of hollow powder,which can be avoided by increasing the gas velocity.

Resonant behaviors of ultra-sonic gas atomization nozzle with zero mass-flux jet actuator

The resonant behaviors of an ultra-sonic gas atomization nozzle with a zero mass-flux jet actuator were numerically investigated with FLUENT software by using a double precision unsteady two-dimensional pressure-based solver. The Spalart-Allmaras turbulence model was adopted in the simulations. Numerical results indicated that the oscillation properties of the gas efflux were effectively improved. Several resonatory frequencies corresponding to different vibration modes of gas were distinguished in the nozzle. With the changing of nozzle geometric parameters, different characters among those modes were elucidated by analyzing the propagations of pressure waves.

A Laboratory Investigation into the Fuel Atomization Process in a Diesel Engine for Different Configurations of the Injector Nozzles and Flow Conditions

This paper reports a laboratory investigation of the fuel injection process in a diesel engine.The atomization process of the considered fuel(a hydrocarbon liquid)and the ensuing mixing with air is studied experimentally under high-pressure conditions.Different types of injector nozzles are examined,including(two)new configurations,which are compared in terms of performances to a standard injector manufactured by the Bosch company.For the two alternate configurations,the intake edges of one atomizing hole(hole No.1)are located in the sack volume while for the other(hole No.2)they are located on the locking cone of the needle valve.The injection process,the fuel atomization fineness and fuel supply speed characteristics are studied as functions of high-pressure fuel pump camshaft speed and rotation angle.The results obtained show that a decrease in the high-pressure fuel pump camshaft speed can produce fuel redistribution depending on the injector operation.In general,however,the hole No.1 can ensure fuel flow with higher speed with respect to the hole No.2 for all the operation modes of the injector.Based on such an analysis,we conclude that the use of certain injectors can enable a fine tuning of the propagation process of fuel sprays into various areas of the diesel engine combustion chamber.

Influence of Self-excited Vibrating Cavity Structure on Droplet Diameter Characteristics of Twin-fluid Nozzle

It is a great challenge to find effective atomizing technology for reducing industrial pollution; the twin-fluid atomizing nozzle has drawn great attention in this field recently. Current studies on twin-fluid nozzles mainly focus on droplet breakup and single droplet characteristics. Research relating to the influences of structural parameters on the droplet diameter characteristics in the flow field is scarcely available. In this paper, the influence of a self-excited vibrating cavity structure on droplet diameter characteristics was investigated. Twin-fluid atomizing tests were performed by a self-built open atomizing test bench, which was based on a phase Doppler particle analyzer(PDPA). The atomizing flow field of the twin-fluid nozzle with a self-excited vibrating cavity and its absence were tested and analyzed. Then the atomizing flow field of the twin-fluid nozzle with different self-excited vibrating cavity structures was investigated.The experimental results show that the structural parameters of the self-excited vibrating cavity had a great effect on the breakup of large droplets. The Sauter mean diameter(SMD) increased with the increase of orifice diameter or orifice depth. Moreover, a smaller orifice diameter or orifice depth was beneficial to enhancing the turbulence around the outlet of nozzle and decreasing the SMD. The atomizing performance was better when the orifice diameter was2.0 mm or the orifice depth was 1.5 mm. Furthermore, the SMD increased first and then decreased with the increase of the distance between the nozzle outlet and self-excited vibrating cavity, and the SMD of more than half the atomizing flow field was under 35 μm when the distance was 5.0 mm. In addition, with the increase of axial and radial distance from the nozzle outlet, the SMD and arithmetic mean diameter(AMD) tend to increase. The research results provide some design parameters for the twin-fluid nozzle, and the experimental results could serve as a beneficial supplement to the twin-fluid nozzle study.

Numerical simulation of influence of nozzle structure on arc characteristics of GPCA-TIG welding

This work mainly articulated the effects of nozzle structure on arc characteristics in gas pool coupled activating TIG （GPCA-TIG） welding process by using Fluent Software. Different models were set up to adapt the different torch structure during computer progress. The specific configuration of the welding torch made the gas flow in outer gas passage constrained. The nozzle structure has great influence on outer gas distribution because of the changing of coupling region between the outer active gas and molten pool surface. When the coupling degree is reduced or the outer gas passage become smaller, the oxygen in outer gas penetrates into the arc plasma and spreads to the arc region more easily. Owing to its cooling effects, the morphology of arc is contracted, and the arc temperature is increased. When the inner wall and the outer wall of outer gas passage are not parallel, the wide top and narrow bottom nozzle shape can bring more oxygen into the arc plasma, the arc is contracted and the peak temperature of arc rises a little more comparing to the narrow top and wide bottom one.

Structural and Regulating Characteristics of Adjustable Annulus-clearance Nozzle Used in Supercritical Fluid Precipitation

A new type of adjustable nozzle with an annulus clearance between the surfaces of a revolved solid and the matched hole was analyzed, which contained matching parts, regulating parts, guiding elements, and sealing part. The general regulating function of the adjustable nozzle was derived and the regulating and matching characteristics were also analyzed. Through the analysis, it was concluded that the matching-profile curve of either the revolved body or matched hole should be chosen as a straight line in order to keep the linear regulating feature. Moreover, the multi-annulus-clearance nozzle was designed, and some experiments were carried out on preparing budesonide particles with the nozzle. According to the experimental results, it was proved that the annulus nozzles is practical in preparing micro-particles by supercritical fluid precipitation method.

Experimental study of the influence of annular nozzle on acoustic characteristics of detonation sound wave generated by pulse detonation engine

Acoustic characteristics of the detonation sound wave generated by a pulse detonation engine with an annular nozzle,including peak sound pressure, directivity, and A duration, are experimentally investigated while utilizing gasoline as fuel and oxygen-enriched air as oxidizer. Three annular nozzle geometries are evaluated by varying the ratio of inner cone diameter to detonation tube exit diameter from 0.36 to 0.68. The experimental results show that the annular nozzles have a significant effect on the acoustic characteristics of the detonation sound wave. The annular nozzles can amplify the peak sound pressure of the detonation sound wave at 90° while reducing it at 0° and 30°. The directivity angle of the detonation sound wave is changed by annular nozzles from 30° to 90°. The A duration of the detonation sound wave at 90° is also increased by the annular nozzles. These changes indicate that the annular nozzles have an important influence on the acoustic energy distribution of the detonation sound wave, which amplify the acoustic energy in a direction perpendicular to the tube axis and weaken it along the direction of the tube axis.

Effects of atomization parameters of dust removal nozzles on the de-dusting results for different dust sources

In order to obtain appropriate spray pressure and enhance the spraying and dust removal efficiency, various factors including the dust characteristics, nozzle spraying angle, effective spraying range, water consumption and droplet size are taken into account. The dust characteristics from different mines and atomization parameters of different pressure nozzles were measured. It was found that the internal pressure of coal cutters and roadheaders should be kept at 2 MPa, which could ensure large droplet size, large spraying angle and low water consumption and hence realizing a large-area covering and capture for large particle dusts. However, the external spray pressure should be kept at 4 MPa for smaller droplet size and longer effective spraying range, leading to effective dust removal in the operator zone. The spray pressure of support moving, drawing opening, and stage loader on a fully mechanized caving face and stage loader on a fully mechanized driving face should be kept at 8 MPa, under which the nozzles have long effective spraying range, high water flow and small droplet size for the rapid capture of instantaneous, high-concentration and small size dust groups. From the applications on the caving and driving faces in the coal mines, it is indicated that the optimization of spray pressure in different spraying positions could effectively enhance dust removal efficiency. Selecting appropriate nozzles according to the dust characteristics at different positions is also favorable for dust removal efficiency. With the selected nozzles under optimal pressures, the removal rates of both total dust and respirable dust could reach over70%, showing a significant de-dusting effect.

Reaction thrust characteristics of high-pressure submerged water jet of cylinder nozzles

The shapes and geometrical parameters of nozzles are key factors for fluidics. The relationship among the reaction thrust,flow rate pressure,diameter d0 and length L of a cylinder nozzle is analyzed theoretically. The simulation of the flow field characteristics was conducted via the FLUENT computational fluid dynamics package. Effects of the inlet conditions and the nozzle dimensions on the reaction thrust of a water jet were addressed particularly. The reaction thrust experiments were performed on a custom-designed test apparatus. The experimental results reveal that a) the nozzle diameter and the inlet conditions exert great influence on the water jet reaction thrust; and b) for L≤4d0,where the nozzle is treated as a thin plate-orifice,the reaction thrust is independent of nozzle length; for L>4d0,where the nozzle is treated as a long orifice,the reaction thrust can reach maximum under the condition of a certain flow rate. These findings lay a theoretical foundation for the design of nozzles and have significant value,especially for the future development of high-pressure water-jet propulsion technology.

Flow structure and rock-breaking feature of the self-rotating nozzle for radial jet drilling

For improving the hole-enlarging capability,roundness and rock-breaking efficiency of the nozzle in radial jet drilling,a new structure of self-rotating nozzle was put forward.The flow structure and rock-breaking features of the self-rotating nozzle were investigated with sliding mesh model and labortary tests and also compared with the straight and the swirling integrated nozzle and multi-orifice nozzle which have been applied in radial jet drilling.The results show that the self-rotating jet is energy concentrated,has longer effective distance,better hole-enlarging capability and roundness and impacts larger circular area at the bottom of the drilling hole,compared with the other two nozzles.Forward jet flow generated from the nozzle is peak shaped,and the jet velocity attenuates slowly at the outer edge.Due to periodic rotary percussion,the pressure fluctuates periodically on rock surface,improving shear and tensile failures on the rock matrix and thereby enhancing rock-breaking efficiency.The numerical simulation results of the flow structure of the nozzle are consistent with the experiments.This study provides an innovative approach for radial jet drilling technology in the petroleum industry.