In the fiber winding process,strong disturbance,uncertainty,strong coupling,and fiber friction complicate the winding constant tension control.In order to effectively reduce the influence of these problems on the tens...In the fiber winding process,strong disturbance,uncertainty,strong coupling,and fiber friction complicate the winding constant tension control.In order to effectively reduce the influence of these problems on the tension output,this paper proposed a tension fluctuation rejection strategy based on feedforward compensation.In addition to the bias harmonic curve of the unknown state,the tension fluctuation also contains the influence of bounded noise.A tension fluctuation observer(TFO)is designed to cancel the uncertain periodic signal,in which the frequency generator is used to estimate the critical parameter information.Then,the fluctuation signal is reconstructed by a third-order auxiliary filter.The estimated signal feedforward compensates for the actual tension fluctuation.Furthermore,a time-varying parameters fractional-order PID controller(TPFOPID)is realized to attenuate the bounded noise in the fluctuation.Finally,TPFOPID is enhanced by TFO and applied to control a tension control system considering multi-source disturbances.The stability of the method is analyzed by using the Lyapunov theorem.Finally,numerical simulations verify that the proposed scheme improves the tracking ability and robustness of the system in response to tension fluctuations.展开更多
Aim Aiming at the position tracking control for valve controlled motor electrohydraulic proportional servo systems mainly driving the static load torque, the tracking performance was studied in the presence of the v...Aim Aiming at the position tracking control for valve controlled motor electrohydraulic proportional servo systems mainly driving the static load torque, the tracking performance was studied in the presence of the variable gain and deadzone. Methods On the basis of conventional composite control with the deadzone compensation method, a comprehensive control approach with the deadzone and self adjusting feedforward compensation was proposed. Results Experimental results showed that the good tracking performance was achieved for the sinusoidal and constant velocity position tracking under a wide variations of load torque. Conclusion The position tracking accuracy for valve controlled motor electrohydraulic proportional servo systems has been solved by using the comprehensive control approach with the deadzone and self adjusting feedforward compensation.展开更多
Base on the accurate inverse of a system, the feedforward compensation method can compensate the tracking error of a linear system dramatically. However, many control systems have complex dynamics and their accurate i...Base on the accurate inverse of a system, the feedforward compensation method can compensate the tracking error of a linear system dramatically. However, many control systems have complex dynamics and their accurate inverses are difficult to obtain. In the paper, a variable parameter model is proposed to describe a system and a multi-step adaptive seeking approach is used to obtain its parameters in real time. Based on the proposed model, a variable-parameter-model-based feedforward compensation method is proposed, and a disturbance observer is used to overcome the influence of the model uncertainty. Theoretical analysis and simulation results show that the variable-parametermodel-based feedforward compensation method can obtain better performance than the traditional feedforward compensation.展开更多
A feedforward compensation naethod of the motion errors of NC machine tools imple- mented with software is proposed , with which the motion errors can be compensated whithout changing the original computer control sys...A feedforward compensation naethod of the motion errors of NC machine tools imple- mented with software is proposed , with which the motion errors can be compensated whithout changing the original computer control systems of the NC machine tools. The experimental results show that the circular interpolation profile machining errors decrease by a factor of 2/3 after com- pensated.展开更多
Current research on lane-keeping systems ignores the effect of the driver and external resistance on the accuracy of tracking the lane centerline.To reduce the lateral deviation of the vehicle,a lane-keeping control m...Current research on lane-keeping systems ignores the effect of the driver and external resistance on the accuracy of tracking the lane centerline.To reduce the lateral deviation of the vehicle,a lane-keeping control method based on the fuzzy Takagi-Sugeno(T-S)model is proposed.The method adopts a driver model based on near and far visual angles,and a driver-road-vehicle closed-loop model based on longitudinal nonlinear velocity variation,obtaining the expected assist torque with a robust H∞controller which is designed based on parallel distributed compensation and linear matrix inequality.Considering the external influences of tire adhesion and aligning torque when the vehicle is steering,a feedforward compensation control is designed.The electric power steering system is adopted as the actuator for lane-keeping,and active steering redressing is realized by a control motor.Simulation results based on Carsim/Simulink and real vehicle test results demonstrate that the method helps to maintain the vehicle in the lane centerline and ensures driving safety.展开更多
The magnetic compensation of aeromagnetic survey is an important calibration work,which has a great impact on the accuracy of measurement.In an aeromagnetic survey flight,measurement data consists of diurnal variation...The magnetic compensation of aeromagnetic survey is an important calibration work,which has a great impact on the accuracy of measurement.In an aeromagnetic survey flight,measurement data consists of diurnal variation,aircraft maneuver interference field,and geomagnetic field.In this paper,appropriate physical features and the modular feedforward neural network(MFNN)with Levenberg-Marquard(LM)back propagation algorithm are adopted to supervised learn fluctuation of measuring signals and separate the interference magnetic field from the measurement data.LM algorithm is a kind of least square estimation algorithm of nonlinear parameters.It iteratively calculates the jacobian matrix of error performance and the adjustment value of gradient with the regularization method.LM algorithm’s computing efficiency is high and fitting error is very low.The fitting performance and the compensation accuracy of LM-MFNN algorithm are proved to be much better than those of TOLLES-LAWSON(T-L)model with the linear least square(LS)solution by fitting experiments with five different aeromagnetic surveys’data.展开更多
同步参考坐标系锁相环是高压直流(high voltage direct current,HVDC)同步触发控制系统中广泛应用的一种窄带宽锁相环,在交流系统故障引起相位跳变情况下,其动态响应缓慢。为增大锁相环的带宽,一种滑动平均滤波器(moving average filter...同步参考坐标系锁相环是高压直流(high voltage direct current,HVDC)同步触发控制系统中广泛应用的一种窄带宽锁相环,在交流系统故障引起相位跳变情况下,其动态响应缓慢。为增大锁相环的带宽,一种滑动平均滤波器(moving average filter,MAF)被前置于锁相环路,然而MAF本身存在响应延迟,制约了锁相环的同步速度。为了缓解响应延迟问题,文中提出一种考虑MAF延时和前馈补偿的HVDC快速锁相环。首先,利用MAF线性暂态特征预测相位变化,并分别针对故障接入和切除引起的相位跳变问题提出不同的补偿策略;接着,利用不变性原理对锁相环路进行前馈补偿,在负反馈控制和前馈补偿共同构成的复合校正控制系统的作用下,锁相环能够在较小PI参数下实现快速响应;最后,将所提快速锁相环在CIGRE HVDC标准模型和三峡—上海直流工程模型中进行仿真验证。结果表明,该快速锁相环能够有效缓解滤波器响应延迟的制约,缩短失锁时间,进而提高高压直流逆变侧抵御换相失败的能力。展开更多
基金funded by the National Natural Science Foundation of China(Grant Number 52075361)Shanxi Province Science and Technology Major Project(Grant Number 20201102003)+3 种基金Lvliang Science and Technology Guidance Special Key R&D Project(Grant Number 2022XDHZ08)National Natural Science Foundation of China(Grant Number 51905367)Shanxi Natural Science Foundation General Project(Grant Numbers 202103021224271,202203021211201)Shanxi Province Key Research and Development Plan(Grant Number 202102020101013).
文摘In the fiber winding process,strong disturbance,uncertainty,strong coupling,and fiber friction complicate the winding constant tension control.In order to effectively reduce the influence of these problems on the tension output,this paper proposed a tension fluctuation rejection strategy based on feedforward compensation.In addition to the bias harmonic curve of the unknown state,the tension fluctuation also contains the influence of bounded noise.A tension fluctuation observer(TFO)is designed to cancel the uncertain periodic signal,in which the frequency generator is used to estimate the critical parameter information.Then,the fluctuation signal is reconstructed by a third-order auxiliary filter.The estimated signal feedforward compensates for the actual tension fluctuation.Furthermore,a time-varying parameters fractional-order PID controller(TPFOPID)is realized to attenuate the bounded noise in the fluctuation.Finally,TPFOPID is enhanced by TFO and applied to control a tension control system considering multi-source disturbances.The stability of the method is analyzed by using the Lyapunov theorem.Finally,numerical simulations verify that the proposed scheme improves the tracking ability and robustness of the system in response to tension fluctuations.
文摘Aim Aiming at the position tracking control for valve controlled motor electrohydraulic proportional servo systems mainly driving the static load torque, the tracking performance was studied in the presence of the variable gain and deadzone. Methods On the basis of conventional composite control with the deadzone compensation method, a comprehensive control approach with the deadzone and self adjusting feedforward compensation was proposed. Results Experimental results showed that the good tracking performance was achieved for the sinusoidal and constant velocity position tracking under a wide variations of load torque. Conclusion The position tracking accuracy for valve controlled motor electrohydraulic proportional servo systems has been solved by using the comprehensive control approach with the deadzone and self adjusting feedforward compensation.
基金supported in part by the National Natural Science Foundation of China(51775215,51535004)。
文摘Base on the accurate inverse of a system, the feedforward compensation method can compensate the tracking error of a linear system dramatically. However, many control systems have complex dynamics and their accurate inverses are difficult to obtain. In the paper, a variable parameter model is proposed to describe a system and a multi-step adaptive seeking approach is used to obtain its parameters in real time. Based on the proposed model, a variable-parameter-model-based feedforward compensation method is proposed, and a disturbance observer is used to overcome the influence of the model uncertainty. Theoretical analysis and simulation results show that the variable-parametermodel-based feedforward compensation method can obtain better performance than the traditional feedforward compensation.
文摘A feedforward compensation naethod of the motion errors of NC machine tools imple- mented with software is proposed , with which the motion errors can be compensated whithout changing the original computer control systems of the NC machine tools. The experimental results show that the circular interpolation profile machining errors decrease by a factor of 2/3 after com- pensated.
基金National Natural Science Foundation of China(Grant Nos.51675151,U1564201)Open Fund of the Key Laboratory of Advanced Perception and Intelligent Control of High-end Equipment of Ministry of Education(Grant No.GDSC202013).
文摘Current research on lane-keeping systems ignores the effect of the driver and external resistance on the accuracy of tracking the lane centerline.To reduce the lateral deviation of the vehicle,a lane-keeping control method based on the fuzzy Takagi-Sugeno(T-S)model is proposed.The method adopts a driver model based on near and far visual angles,and a driver-road-vehicle closed-loop model based on longitudinal nonlinear velocity variation,obtaining the expected assist torque with a robust H∞controller which is designed based on parallel distributed compensation and linear matrix inequality.Considering the external influences of tire adhesion and aligning torque when the vehicle is steering,a feedforward compensation control is designed.The electric power steering system is adopted as the actuator for lane-keeping,and active steering redressing is realized by a control motor.Simulation results based on Carsim/Simulink and real vehicle test results demonstrate that the method helps to maintain the vehicle in the lane centerline and ensures driving safety.
基金National key special projects for major scientific instruments and equipment development(2017YFF0107400)。
文摘The magnetic compensation of aeromagnetic survey is an important calibration work,which has a great impact on the accuracy of measurement.In an aeromagnetic survey flight,measurement data consists of diurnal variation,aircraft maneuver interference field,and geomagnetic field.In this paper,appropriate physical features and the modular feedforward neural network(MFNN)with Levenberg-Marquard(LM)back propagation algorithm are adopted to supervised learn fluctuation of measuring signals and separate the interference magnetic field from the measurement data.LM algorithm is a kind of least square estimation algorithm of nonlinear parameters.It iteratively calculates the jacobian matrix of error performance and the adjustment value of gradient with the regularization method.LM algorithm’s computing efficiency is high and fitting error is very low.The fitting performance and the compensation accuracy of LM-MFNN algorithm are proved to be much better than those of TOLLES-LAWSON(T-L)model with the linear least square(LS)solution by fitting experiments with five different aeromagnetic surveys’data.
文摘同步参考坐标系锁相环是高压直流(high voltage direct current,HVDC)同步触发控制系统中广泛应用的一种窄带宽锁相环,在交流系统故障引起相位跳变情况下,其动态响应缓慢。为增大锁相环的带宽,一种滑动平均滤波器(moving average filter,MAF)被前置于锁相环路,然而MAF本身存在响应延迟,制约了锁相环的同步速度。为了缓解响应延迟问题,文中提出一种考虑MAF延时和前馈补偿的HVDC快速锁相环。首先,利用MAF线性暂态特征预测相位变化,并分别针对故障接入和切除引起的相位跳变问题提出不同的补偿策略;接着,利用不变性原理对锁相环路进行前馈补偿,在负反馈控制和前馈补偿共同构成的复合校正控制系统的作用下,锁相环能够在较小PI参数下实现快速响应;最后,将所提快速锁相环在CIGRE HVDC标准模型和三峡—上海直流工程模型中进行仿真验证。结果表明,该快速锁相环能够有效缓解滤波器响应延迟的制约,缩短失锁时间,进而提高高压直流逆变侧抵御换相失败的能力。
